Search Documents

By S. M. Khandrika

Most of the coal presently used by the utility industry is cleaned at preparation plants employing wet processes. While water is the mainstay of coal washing, it is one of the least desirable components in the final product causing a reduction of the heating value as well as handling difficulties. Currently available dewatering techniques are inefficient for dewatering very fine coal (minus 325 mesh). The US coal industry has expressed serious concern about utilizing advanced cleaning processes such as column flotation because an efficient and economical dewatering process is not available.

Jan 1, 1992

By I. H. Gundiler

A pilot-plant flotation concentrate containing 21.6 g/t gold and 2 kg/t silver was used for this study. Base-line cyanide and thiourea tests showed 30-40% extraction of both gold and silver. After roasting (450-750C), the maximum gold extracted was 89% with thiourea and 76% with cyanide. Pressure oxidation tests were conducted following a statistical experimental design in a 2L laboratory autoclave at 10% pulp density, and the residues were subsequently leached in acidic thiourea solutions for 2h. Leach results were presented in the form of contour maps, and optimum autoclave conditions were determined for maximum gold extraction (93%). However, silver extraction was only 7% when gold extraction was maximized.

Jan 1, 1992

By William R. Yernberg

Caterpillar introduced 21 new products during Caterpillar Press Days ‘96, held in June at the company’s proving grounds near Tucson, AZ. The event, billed as the largest product introduction ever held by Caterpillar, was attended by press from around the world. Most of the new products were demonstrated at Caterpillar’s Tinaja Hills Training Center in the Sierrita Mountains south of Tucson. Under the scorching Sonora Desert sun, the press was treated to demonstrations of the new equipment. After a display of the equipment’s power and capabilities, the press was given an opportunity to operate the new models and, in some cases, compare them with the old.

Jan 1, 1996

By Christopher Mark

Area wide pillar failures, or “squeezes,” were once fairly common in underground coal mines. While rare today, they do occur. This paper describes seven case histories that were investigated by MSHA Technical Support. They occurred across the range of US coalfields, in both longwall and room-and-pillar mines, and involved development mining, pillar recovery, longwall panel extraction, and multiple seam interactions. Significant lessons from each are discussed.

Jun 25, 2024

By Boyd Eisenbraun, Dennis Murr, Milton Rojas

Approximately since 1925, the phenomena of grinding and classification of minerals with screens have been studied. In the U.S. iron ore mining operations located in the so-called “Mesabi Iron range,” magnetite processing plants have made progress in the application of high-frequency screens that have allowed them to process low-grade Taconite ores and successfully achieve the economic benefit of these minerals. In the particular case of magnetite minerals disseminated in the siliceous matrix, the main objective is to reduce the generation of particles called “middlings” with high silica contents. Commonly the primary challenge of the metallurgical task is to achieve high recoveries and iron concentrates with low impurities. To achieve this, several studies and industrial applications have shown success in this regard and not only in iron ores, but also in other minerals around the world. The study described in this paper attempts to describe some key aspects that helped develop an effective solution and list the benefits associated with this modern process design by using industry-proven technologies for minerals in Chile that have similar characteristics to the minerals of the iron belt in the United States.

Feb 1, 2025

By Kenneth W. Torpey, James G. Ball, Richard F. Flanagan, David S. McAllister

INTRODUCTION Under a Federal grant by the Urban Mass Transit Administration (UMTA) (80%), and sponsored by the State of New York (200), Niagara Frontier Transportation Authority is constructing a 10.3 km (6.4 mile) light rail rapid transit system in Buffalo, New York. The $450 million project, which began construction in the Spring of 1979, is unique in rail transit alignment designs in the U.S.A. and the first predominantly underground light rail system in North America. The Buffalo project is unique in that the first phase of the expandable system follows the alignment of Main Street and is on the surface in a proposed 1.6 km (1.0 mile) pedestrian mall in the downtown business district. The alignment then progresses northward into a cut-and-cover portal and standard double-box configuration for 2.74 km (1.7 miles) at a depth of 9.1-10.7 m (30-35 ft) and subsequently drops into bedrock at depths of 18.3-27.4 m (60 to 90 ft). The 5.63 km (3.5 mile) rock tunnel section consists of two single tunnels 4.88 m (16.0 ft) nominal finished diam. and includes five stations. The rock tunnel line section was divided into a north and south contract of 2 316 m (7,600 ft) and 3 243 m (10,640 ft), respectively. Due to the existing surface facilities and the future station locations, the line tunnel contracts differed considerably in their shaft access

Jan 1, 1981

By A. B. Cecala

The US Bureau of Mines has designed and evaluated total mill ventilation systems (TMVS) at two mineral-processing operations. Both systems have proven proficient at cost-effectively reducing respirable dust levels throughout the mills. An 11.8-m3/sec (25,000-cfm) system installed at a clay-processing mill provided about 10 air changes per hour(acph). This system reduced respirable dust concentrations by about 40% throughout the mill building. The second evaluation was performed at a silica sand operation. Tests were performed with 23.6 and 47.2 m3/sec(50,000 and 100,000 cfm) of ventilation to the mill building, corresponding to 17 and 34 acph. Average mill-wide respirable dust reductions were 36% and 64%, respectively. This work was done to determine general guidelines and design criteria for operations that may be interested in implementing TMVS. TMVS should be designed to draw clean make-up air in near the base of the mill. This air provides general purging and may clear some dust-laden areas throughout the mill structure. It is discharged at or near the top of the structure. Without the TMVS, dust can exit the building through open doors, windows, etc. and contaminate outside plant workers. This dust can also be recirculated back into the mill building causing additional contamination problems. TMVS is not a stand-alone system. It is a supplemental technique to assist other localized dust control systems (Mody et al.,1987).

Jan 1, 1995

The 2014 George A. Fox Conference at the Graduate Center, City University of New York in New York City was presented under the theme, ?21st Century Challenges for the Tunneling Industry. Bruce Grewcock, chief executive officer and president of Peter Kiewit Sons? Inc., opened the conference with a keynote address in which he set the tone for the rest of the day by touching on the many challenges the industry is facing, which are plentiful and complex. Covering the breadth of the industry, he spoke about everything from the technical challenges that come from working beneath the streets of some of the most densely populated regions in the world to the challenges that come from working with the people who live in those areas. ?My observation is that we, as an industry, are being asked to put structures in places where they are needed, but are complex environments to work in,? said Grewcock. ?We work in an industry that relies on some of the most technically challenging engineering in the world, and when we are done with a project, we cover it up and no one ever sees it.? Despite these issues, Grewcock said that, in his opinion, the biggest challenge the industry is facing is that of people; more precisely, where to find the next batch of people. Looking out at the conference-record crowd of more than 400 registered attendees, Grewcock quipped that he saw plenty of gray beards and asked aloud, ?Where will we find, educate and train the people to tackle the issues that this industry will face in the future??

Mar 1, 2014

By A. J. Naldrett

Over the past six or seven years important new ideas have been developed concerning the origin of nickel sulfide deposits. To a large extent these have been stimulated by the major nickel discoveries of the Eastern Goldfields area of Western Australia (Woodall and Travis, 1969; Ewers and Hudson, 1972). Prior to these finds, the most important nickel camps were regarded as being associated exclusively with intrusive rocks such as the Nickel Irruptive at Sudbury or the intrusive peridotites at Thompson, rocks that were thought to have no close association with volcanism. Study of the Australian discoveries, coupled with work in South Africa (Viljoen and Viljoen, 1969) and Canada (Naldrett and Mason, 1968; Pyke, Naldrett and Eckstrand, 1973), has shown that volcanic rocks with true ultramafic compositions and extrusion temperatures of 1400 to 1600°C were a common feature during the Archean. Under certain circumstances economic concentrations of nickel sulfides have formed from these rocks, either settling to the base of their associated flows or accumulating in shallow intrusive feeders to the flows. The aim of this article is to show how these ultramafic rocks can be recognized, how the nickel deposits, if present, are likely to occur within them, and what special features characterize ore-bearing examples of the rocks.

Jan 1, 1975

By E. S. Forbus

A process for producing reductive bleach in-situ in kaolin slurries has been developed. The bleach is formed by mixing an iron sponge powder (-325M) with slurry treated with SO2. The process has been successfully demonstrated in production, and applied to several grades. The color, brightness, and viscosity of the bleached product is equivalent to or better than that of product bleached with commercial sodium hydrosulfite . The tested products can be bleached at a cost, which is 38-54% of those associated with the use of commercial bleach.

Jan 1, 1993

By E. Fidler

A recent headline in the Wall Street Journal declared, "trendy management schemes very often fail." Many of the management techniques addressed in the accompanying article are associated with quality management including reengineering, benchmarking, total quality management, and employee empowerment. The article made the point that executives, employees, and customers who are involved in such programs rate the effectiveness of these programs very low, and the programs often fail. Yet, we all know of companies that have made significant advances in their operations using these same quality management practices. Why do a few succeed while many fail? History has shown that the companies that successfully carry out quality management programs have two things in common: 1) Strong leadership committed to the success of the program. 2) A comprehensive plan for carrying out and maintaining the program. Stated another way -the reason many companies fail is the lack of committed leaders and inadequate planning. It is ironic that the title of the Wall Street Journal article is "The Best Laid Plans."

Jan 1, 1994

By W. R. Reed

This study evaluates the roof-bolter canopy air curtain (CAC) system in an exhausting face ventilation system, demonstrating its effectiveness and illustrating the CAC protection zones. Two scenarios are considered: (1) a roof-bolting machine in the center of the entry for installation of the fifth row of bolts from the face, and (2) a roof-bolting machine positioned close to the face for the installation of the last row of bolts. In both scenarios, the bolting machine is placed in an environment that contains 6.0 mg/m3 of respirable dust and is ventilated by an exhaust curtain with 9,000 cfm (4.25 m3/s) of air to simulate the roof-bolter machine operating downstream of a continuous mining machine. Two operation positions are simulated at the same bolting location: dual drill heads in the inward position for two inside bolts and in the outward position for two outside bolts. The influence of the CAC on airflows and dust dispersion is evaluated with the CAC operating at 250 cfm (0.12 m3/s) with dust reductions ranging from 39.5 to 82.8 percent. When the roof bolter is operated close to the face, increasing CAC airflow was required for adequate protection, as the dust reductions can be as low as 39.5 percent. Increasing CAC airflows to 350 cfm (0.17 m3/s) and 450 cfm (0.21 m3/s) were evaluated, demonstrating that dust reductions increased to 59.7 percent (350 cfm) and 72.0 percent (450 cfm). These results revealed improvement in respirable dust reductions compared to the CAC airflows at 250 cfm when the bolter is operated close to the face, showing the CAC can provide protection against high respirable dust concentrations for roof-bolter operators.

By Daniel Maine

Swelling clay soils have been problematic to many types of infrastructure in the United States. However, their impact on underground construction is often misunderstood. The use of swell pressures in design of initial tunnel and shaft support lacks proper guidance and is often mis-interpreted. This paper provides insight and guidance on how to implement a geotechnical investigation program to determine if swelling soil exists at a site and how it impacts the design of temporary support systems for underground projects. An example is provided for how swell pressures were incorporated into the design of an initial support system for a rib and lagging tunnel system and problems that occurred.

Jun 23, 2024

By Ross Goodman, Jean-Luc des Rivières

The Ohio River Tunnel Project encountered multiple unexpected geotechnical challenges which, continuing to develop over time, hampered excavation completion and impacted the cast-in-place final lining technique and work execution sequence for the entire project. The continued degradation of the excavated hard rock tunnel conditions led to a unique, dynamic, geologic setting that forced the project to innovate new and adaptable measures allowing for a conventional cast-in-place liner to be completed in a safe and timely manner and minimize delay.

Jun 13, 2023

By James S. Browning

The Mineral Resources Institute of The University of Alabama conducted research on the removal of sulfur from coal using a combination of gravity concentration and flotation methods. The research utilized the gravity and centrifugal force capabilities of the Humphreys spiral to remove part of the pyritic sulfur and ash. Flotation of the Humphreys spiral coal concentrate removed additional sulfur and ash to yield products that conform to Federal air quality standards for sulfur oxide emissions. The clean coal products recovered by the combined process contained 7.7 to 8.0 percent ash, 0.12 to 0.16 percent pyritic sulfur, and 0.78 to 0.96 percent total sulfur. Pyritic sulfur rejection by the process was about 95 percent. In addition to obtaining good recoveries of high quality coal the tests demonstrated that the pyrite in the wastes could be isolated as enriched flotation products by the combined gravity - flotation apporach. Pyrite concentrates analyzing 25 to 33 percent sulfur were recovered. Potential benefits of the pyrite flotation step are recovery of a product of possible market value and the elimination of the pyrite from the waste ash which could be a potential acid water problem when impounded.

Jan 1, 1981

By D. A. Fenton

Two large 34 ½ foot diameter mills have seen seven years of continuous operation before massive fracturing occurred on one of the trunnion cones. These fractures were discovered when liner changes were made. Four modes of failure were identified, three of the modes combining to cause a large circumferential tear in the 4-inch cone plate. A theoretical account is made of the modes of fracture and comparison made with field results. New material was used to repair the fractured cone, and the complete repair took ten weeks. The repair was monitored and lasted twenty-six weeks before the newly designed structure was available.

Jan 1, 1982

By Robert C. Freas

The Northeastern United States is the most highly urbanized region in North America. It is also an area with a tremendous appetite for stone products. Within this context limestone has truely become an "urban ore". Its uses extend from traditional aggregate markets to lawn and garden, archetectual, chemical, agricultural, industrial, and environmental applications. This paper looks at both the occurance and uses of limestone in the northeast, and briefly examines changing patterns in consumptive use.

Jan 1, 1985

Placing a detonating explosive inside a volume of rock is an efficient method of rock fragmentation. The explosion generates internal tensile stresses in the rock, and because rock is a brittle material, this brings about crack propagation and fragmentation far more efficiently than does application of explosive on the surface. To get the explosive inside, we drill a pattern of boreholes and charge the explosive into the holes. This is really the one and only purpose of making blastholes in mining: to give access for the explosive to the interior of the rock. No matter how big and expensive a drilling jumbo we stand up in front of a rock face, and no matter how many boreholes we let it drill, the rock does not fall apart by itself without blasting. It is the action of the explosive in the boreholes that does it. When we consider that we need a pound or two of explosive for every cubic yard of rock to be fragmented, and a pint of borehole volume for each pound of explosive, we see that the process of blasthole charging is an important element in the whole process of rock blasting.

Jan 1, 1975

By X. P. Zheng

Barium fluorphlogopites were synthesized in the laboratory in order to investigate the effects of composition and crystal parameters on surface properties and floatability. The negative surface charge of mica is determined by the barium content, the crystal cell volume, the distance between layer structure and the Ba-O bond length. The higher barium content, the larger the cell volume and distance between the layer structure and the longer the Ba-O bond, the more negatively charged the surface is and hence the more easily adsorbed to cationic collectors. When an anionic collector (sodium oleate) is used, barium oleate forms on the mica surface and hence chemical adsorption occurs.

Jan 1, 1993

By Robert G. Beverly

INTRODUCTION Standards limiting the annual exposure of United States uranium miners to radon daughters were established in 1967 at 12 Working-Level-Months (WLM). The standard was reduced by a factor of three, to 4 WLM, in 1971. Currently, the standard is again being examined to determine if it should be changed. Since 1967, Union Carbide has calculated individual monthly exposures in company and contract-operated mines located on the Colorado Plateau. Although it has been possible, by extensive ventilation control measures and accurate routine sampling, to meet the current exposure standard, there are many miners whose exposures closely approach the 4 WLM standard for any given year. However, it was noted that for miners who work for any extended period of years the [average] exposure was much less than the standard. The primary purpose of this paper is to show that, in effect, any annual exposure standard to radon daughters results in a long-term exposure considerably below that standard. Further, most miners, due to their job assignments and/or employment habits, only receive a small fraction of the standard. HISTORY OF EXPOSURE STANDARDS Prior to 1967, radiation protection in uranium mines was fundamentally based on a radon daughter concentration guide. In 1960, the American Standards Association published mine and mill radiation protection standards (ASA-1960). The Colorado Department of Mines, in 1961, adoped a standard which followed the ASA Standard and provided that if concentrations exceeded 10 Working Levels (WL), the area was to be shut down until corrective action was taken; if between 3 and 10 WL, corrective action was to be initiated; between 1 and 3, additional samples were to be taken and individual exposures evaluated; and if below 1 WL, conditions were considered to be controlled. In 1967, the U.S. Department of Labor issued the first exposure standard which called originally for limiting annual exposures to 3.6 WLM but which was later changed to 12 WLM. The complicated regulatory developments leading to this standard have been described elsewhere (Beverly-1969, Rock & Walker-1970). Effective July 1, 1971, this exposure standard was lowered to 4 WLM per year, which is the current standard. Over the past year, there has been speculation about the potential risk to uranium miners working at the present standard. A recent NIOSH Study Group Report (NIOSH-1980) concluded: "There is also strong evidence that a substantial risk extends to and below 120 WLM of exposure." The 120 WLM corresponds to a miner working in uranium mines for 30 years, a rare occurrence, at an exposure rate of 4 WLM per year, an even rarer occurrence. On the other hand, the General Accounting Office, in a recent Report to the Congress (GAO-1981), was very critical of reports by NIOSH on general low-level radiation risks. The GAO recognized that”...important questions remain unanswered about the cancer risks of low-level ionizing radiation exposure;" and recommended that Congress enact legislation giving statutory authority to an interagency committee to coordinate Federal research on health effects of ionizing radiation exposure. The International Commission on Radiation Protection at its March, 1980 meeting recommended limiting the inhalation of radon daughters to 0.02 J per year, equivalent to 0.4 WL, which on an annual basis would be 4.8 WLM and noted it is common to reduce this figure by 20% for allowance in the case of uranium miners for external and/or dust exposure(Sowby-1980). This is essentially equal to the present standard of 4 WLM. As earlier uranium miner exposure studies are reevaluated, and as new studies are conducted, it is important that the relationship between regulatory standards and the resulting actual exposures be recognized. UNION CARBIDE URANIUM MINING EXPERIENCE Union Carbide started mining Colorado Plateau uranium-vanadium ores in the late 1920s for the contained vanadium values. In the early 1950s, the Atomic Energy Commission contracted Union Carbide to produce uranium at mills located in Uravan and Rifle, Colorado. The company now has over fifty years of mining experience in the area. Some mines are operated as company mines and others are operated by private mining companies under a contractual arrangement. Ventilation, sampling, and exposure calculations are carried out the same in contract mines as in company-operated mines. Data presented in this report do not differentiate between company or contract employees and include all employees who worked underground any portion of a year in Union Carbide mines from 1967 through 1980. At the peak of uranium mining activities in 1970, there were 577 miners employed at year end (285 company employees and 292 contract) and 52 mines in operation (8 company-operated and 44 contract mines). Contract mines varied from two-man operations up to 15 employees. Company mines were generally the larger operations and employed from 20 to 100 miners.

Jan 1, 1981