Search Documents

By E. A. Rychkun

Mining and environmental objectives have traditionally been in conflict. This conflict reflects a delicate balance between the need to spend money to protect the environment, and the need to save money by extracting minerals efficiently. In an increasing number of cases, profit margins diminish rapidly with new environmental regulations and reactionary measures. Forced cleanups and increasing restrictions are unwelcome expensive processes. A practical solution lies in planning rather than reacting. This requires the ability to precisely quantify and qualify environmentally sensitive problems by providing effective engineering tools to model, visualize and analyze subsurface conditions. Prevention of environmental conflicts, and effective cost control are both rooted in the mining company's ability to construct accurate models, monitor changes, assess contamination risks and to design effective remediation plan. This paper presents a case study where these issues are addresses through the application of a new and innovative technology.

Jan 1, 1993

By A. R. Rule

As part of the Federal effort to help maintain an adequate supply of fertilizer minerals, the Bureau of Mines is conducting research to characterize complex, low-grade western phosphate rock and to develop methods for economic recovery of phosphate. The rock varies from soft, friable, altered phosphatic shale to hard, tightly cemented, unaltered phosphate rock. To supplement current beneficiation by sizing, a flotation procedure was devised that included depression of phosphate minerals with H2SiF6 and anionic flotation of carbonate minerals, followed immediately by cationic flotation of silicate minerals. Application of the procedure to several different ores resulted in phosphate concentrates that ranged from 28 to 31 pct P20S in grade and from 60 to 70 pct in phosphate recovery.

Jan 1, 1977

By E. M. Wilde

Through the USGS's National Coal Availability program, coal resource appraisals have been completed for three 7.5-minute quadrangles (Willow Crossing, Colstrip East, Colstrip SW) in the Powder River Basin area of southeastern Montana. Available coal reserves (original reserves minus tonnages affected by current restrictions) vary from 44 to 70 percent of the original reserves. Major restrictions impacting each area also vary. In each area, one or two beds contain most of the reserves, but up to eleven beds contain available coal. The main beds in completed studies are the Knobloch, Rosebud, Sawyer and Flowers-Goodale. Three additional areas (six 7.5-minute quadrangles) are in preparation.

Jan 1, 2001

By M. Albrecht

In the mining industry and particularly in the processing plants, we use some large and unusual equipment. Understanding what it is and what it does is important to good operations, but how do you teach a new employee. When I started out in this field, the information on the processing equipment was easy to come by. Equipment manufacturers readily supplied it; their salesmen, often engineers themselves, knew how important the availability of this information was. Old engineers used their notebooks to train the new engineers. Over time this has changed. Equipment manufacturers have changed hands or gone out of business, and often the older engineers are gone. As a start in reversing this, this presentation will be an introduction to sizing, selecting, and operation of some of this equipment, in particular gravity separating equipment. Major portions of this have been excerpted from A Mining Engineers Notebook: Mineral processing (2).

Feb 23, 2014

By Bruce Kennedy, Charles Bruce

MINERAL EXPLORATION 'The Function of Exploration Mineral exploration aims at locating the presence of economic deposits and establishing their nature, shape, and grade. As all ore bodies are finite, exploration is essentially the lifeblood of the mining industry. It is divided into two phases, reconnaissance and target investigation. It involves geological mapping, geophysical prospecting (aerial and ground or both), geochemical surveys, prospect drilling, and/or exploratory under-ground workings. Successful exploration is followed by development drilling, mine development, and eventually operation. In underground mining, the term "ore" is applied rather loosely to metalliferous rock that can be profit- ably mined, but nonmetallic industrial minerals and energy related materials constitute a large and growing portion of the tonnage extracted by underground methods each year. It is appropriate, therefore, to consider exploration as the search for any useful substance occurring in the earth or in the oceans that is of sufficient value as to volume, grade, chemical and physical com- position, and location as to make extraction by mining commercially profitable for the investment required. The Selection Process The search for ore includes hundreds of mineral commodities. The more successful exploration organizations tend to restrict the search to the mineral commodities for which they have strong exploration expertise and which have a high probability of being concentrated in areas open to exploration and development in sufficient volume, grade, and proximity to the surface to warrant the large expenditures of risk capital in finding an ore body. Special expertise is needed to engage in mineral exploration and development for the extended periods required for success. Individual prospectors continue to discover mineral occurrences, but it generally takes an organization with strong financial resources to carry the exploration process forward to the point of developing "ore." Still greater corporate resources in the form of management, engineering, and sales capability are needed to develop an ore body into an operating mine. In the past, companies other than those engaged in mining rarely conducted exploration, since they lacked the technical skills and know-how to bring a mine to fruition. A notable trend in recent years has been the success of other resource-oriented firms, such as petroleum companies, that have not only acquired the necessary skills to engage in exploration for hard minerals, but are doing so on a far more intensive scale than known in the industry heretofore. The desire to diversify from increasingly regulated oil and gas, the potential for the discovery of a bonanza, and the large scale of mining projects for these capital-intensive firms are the attractions. US government and certain international organizations, such as the United Nations, have fielded sizable exploration programs in the past decade on behalf of Third World countries wherein many of the world's higher grade deposits and scarce mineral resources are located. The level of overall mineral exploration in the industry is, regrettably, closely geared to the business cycle. Accelerated search during the periods of strong demand, shortages, and high prices, together with the long lead times necessary to develop mineral finds, often creates surges in supply which invariably are followed by a collapse in prices. The trend is, therefore, to exploration funding by larger better-endowed firms having the staying power to weather the cyclical nature of mining. Tax incentives, tariff policies, and other incentives have a decided impact on the level and nature of exploration. Surface mining regulations and environmental forces have fostered a renewed interest in under- ground development despite the lower average costs of surface mining. Spiraling inflation has caused mining costs to outpace prices for many mineral substances. Organizations increasingly are directing their search away from high- grade but limited tonnage occurrences toward low-grade disseminated bulk tonnages amenable to mining on a vast scale. Mining continues, therefore, to grow even more capital-intensive with half-billion-dollar mine-mill- smelter complexes now commonplace, compared with the hundred-million-dollar projects of a decade ago. Reconnaissance Exploration Having elected to search for specific mineral commodities, the exploration company narrows its focus to a reconnaissance of those regions offering the best potential. A working hypothesis which is constantly up- dated concerning the geologic controls for ore occurrence guides the search. The possibilities for discovery are best in areas of existing mines and known ore bodies, where the probabilities are high for additional ore occurrences. In such areas, published data on the trends and geologic controls of known mineral occurrences aid the search. Even in some remote territories, a variety of geologic data is available to the explorationist. The major sources of basic geologic data are the libraries of the US Geological Survey (USGS), the state geological surveys, the American Institute of Mining, Metallurgical, and Petroleum Engineers (AIME), the US Bureau of Mines, and various institutions such as Colorado School of Mines. Overseas, virtually all of the countries have their own geologic survey groups which are associated directly, or indirectly, with their respective ministries of mines. The objective of reconnaissance exploration is to narrow the search by pinpointing target areas having interesting mineralization. These favorable areas are then investigated in detail to delineate potential ore bodies.

Jan 1, 1982

By Miguel Reyes, Chenming Zhou, MATTHEW GIRMAN

This paper is aimed at helping the mining industry to better understand the challenges posed by electromagnetic interference (EMI) and to promote electromagnetic compatibility (EMC) in underground coal mines. The paper begins with a review of EMI standards in other industries, then presents some representative examples of EMI instances that have occurred in the mining industry, followed by a literature review of published EMI research in mining and, finally, a discussion on mitigation strategies and practical considerations related to EMI in mining.

By Amanda Powers, Brian Glynn, Robert Sauceda, Daniel Huffines, Mike Garbeth

This paper will review the evaluation performed for the Cottonwood & Hackberry Creek Wastewater Interceptor Improvements Project to replace two separate aging and undersized interceptor sewers by either open cut construction or trenchless construction methods. A case study will be discussed for the utilization of microtunneling to avoid a deep open cut excavation within a landscaped roadway median to construct nearly a mile of new 60-inch interceptor sewer in an urban area adjacent to an environmentally sensitive riverine area, while minimizing the permitting and environmental impacts of construction, and minimizing the impacts to residents and vehicular trafc and restoration reuirements.

Jun 23, 2024

By Ping K. Di

A naturally aged and synthesized manganese oxide-coated granular media was found in our laboratory to have the capability of the removal of soluble Mn(H) from mine drainage by adsorption and oxidation. Mine drainage commonly also includes other heavy metal ions. Extending this principle, this paper presents the removal of heavy metals including lead, copper, cobalt, zinc and nickel in the aqueous solution by using the synthesized manganese oxide-coated granular media. It was found that the adsorption of lead, copper, cobalt, zinc and nickel on the manganese oxide-coated media follows both Langmuir and Dubinin-Radushkevich adsorption isotherms except in the concentration range less than 0.1 mmole/L. The adsorption mechanism involves the ion exchange between the heavy metal ions and synthesized manganese oxide coated on the media. The synthetic manganese oxide surface has a strong metal binding ability to the heavy metals in the order of Pb2+ > Cu2+ > Ni2+ > Zn2+ > C02+ based on the adsorption results using batch and continuous column operations. The breakthrough curves of these heavy metals showed that the synthesized media could be used effectively in the removal of these heavy metal ions in a cell or packed column. The process can simultaneously facilitate the immobilization of the heavy metals on the synthesized manganese oxide coated media. A subsequent pH adjustment dislodges the heavy metals and regenerates the synthetic media. Thus, the process accomplishes the adsorption, immobilization and concentration of the heavy metal from waste stream in one monolithic procedure.

Jan 1, 1995

By C. Zhou, J. Srednicki

Electronic systems have been increasingly used in underground mines to improve mine safety. These electronic systems emit electromagnetic (EM) energy which can adversely impact the performance of other electronic systems nearby and thus should be characterized. Researchers at the National Institute for Occupational Safety and Health (NIOSH) characterized the magnetic fields emitted from devices that can potentially interfere with the performance of proximity detection systems (PDSs) and compared the emission levels of these devices to the susceptibility of PDSs. In this paper, we present our measurement results pertaining to this effort. Particularly, magnetic fields emitted from the different orientations of a powered air purifying respirator (PAPR) and two lite trackers are evaluated based on the RE101 protocol specified in the MIL-STD-461G standard. The results show that both devices emit strong magnetic fields which strongly depend on the orientation of the devices. At some frequencies, the maximum emission levels from the two devices exceed both the emission limit given in MIL-STD-461G and the maximum magnetic fields that a PDS can withstand without a failure. The results and findings in this paper can help the mining industry better understand electromagnetic interference (EMI) underground and provide critical scientific data that support mining-specific recommendations to address EMI-related challenges.

Feb 1, 2023

Unplanned ore dilution can have severe impact on the economics of a mining operation. The paper discusses and distinguishes between controllable and natural parameters influencing ore dilution, and how it can be minimized in longitudinal mining systems of narrow vein orebodies. It is shown through data of surveyed stope profiles and numerical modelling that unplanned ore dilution is a function of stope design and construction, orebody geometry, and rock mass characteristics.

Jan 1, 2010

By James A. Decker

Hanna has developed three production planning systems to help the mine engineers determine the sequence of mining from available ore supples. The Production Scheduling System was developed to give the staff a tool for long range planning by sequencing the removal of blocks from an open pit property. It was needed to determine the year of removal for each block so that the optimum present-valued pit limits could be established by our pit design program. Since in this type of planning short term grade control is less of a factor than it is in daily or monthly planning, the system gives the program greater control and more latitude in block selection. It permits only full blocks to be taken.

Jan 1, 1984

By M. C. Stuttle

MDL Rock Lasers has undertaken successful mapping trials of abandoned mine workings using its underground cavity scanning system. The work was being performed for Kalgoorlie Consolidated Gold Mines (KCGM), Australia's largest gold producer. MDL Rock Lasers supplies underground surveying systems to the mining and quarrying industry KCGM's Fimiston Super Pit, located in Kalgoorlie, Western Australia, is Australia's largest open-pit gold operation. Fimiston's final pit design is expected to be 3.7 km (2.3 miles) long, 1.5 km (0.9-miles ) wide and 540 m (1,770 ft) deep. During the early days of Australian mining, underground operations were labor intensive. Mining was selective and generally narrow stopes were mostly backfilled. Improved processing technology and mine mechanization during the 1970s and 1980s has permitted larger scale operations to adopt less selective underground-stope operations. The "super pit" concept was a logical step for mining companies working toward economies of scale. However, the industry recognized that there was no precedent for excavating a 500-m- (1,640-ft-) deep open pit through ground previously affected by old workings. To appreciate the geotechnical challenge facing KCGM, it is necessary to consider that under the pro¬posed area at the open pit, stoping reached a level of 1 km (0.6 miles) and was supported by more than 2,000 km (1,240 miles) of development headings. The company was fortunate because plans were available for the Golden Mile underground operations. The existing plans were interpreted by the mine's geotechnical team and computer models were constructed of the underground workings. These models can be imported into three-dimensional mine planning packages, such as the Vulcan's Unix-based software, Envisage, to assist analysis and design. This prior knowledge of the workings provided the focus for investigating and confirming ground conditions using probe drilling. After several iterations of drilling, followed by detailed analysis, several decisions were made relating to the nature of the ground and the mining approach to be taken. It was recognized that the stope models were not perfect due to hu¬man error, lack of original survey information and progressive deterioration in ground conditions. It also became apparent that the sole reliance on probe drilling was inefficient in terms of time and quality of information. This was particularly true in complex areas where stopes are in close proximity. A major concern was the presence of open stopes (voids). In many cases, stopes consist of combinations of filled and void sections. The condition of pillars within these underground workings is extremely important. In time, pillars collapse and voids will propagate in upward and lateral directions. So systems needed to be developed that allowed rapid and accurate verification of ground conditions. KCGM was introduced to MDL Rock Lasers while investigating technology for underground mining. The two companies decided to use the C-ALS, MDL Rock Laser's underground laser, cavity scanning system, to improve the management of mining through affected ground. This system was to be used in conjunction with probe drilling and void mapping activities. A field test in one area of the Fimiston Mine verified the capability of the C-ALS system to quickly and efficiently assist in this decision making process. The C-ALS scanner features lightweight, carbon fi¬ber alignment rods from Measurement Devices Ltd.'s (MDL) Boretrak MKII. This is a borehole deviation system that stops the two axis measurement head rotating and lowers the system down a borehole. The scanner is deployed by a 110-mm (4.3-in.) borehole, up, down or sideways. The operator can then carry out vertical and horizontal plan section scans at any user specified ARC (an angular increment of 2°) or the distance between two points on the ARC (CHORD) increments. Windows '95 software enables the operator to control the cavity scanner remotely, surveying the area in real time. The system makes data quick and convenient.

Jan 1, 1999

By B. Kyslinger

"In underground mining, machine design is predominantly dictated by mine conditions and individual customer desires. In partnership with Foresight Energy, J. H. Fletcher & Company was tasked to design and manufacture a new roof bolting machine with six independent drilling apparatus on board capable of drilling and bolting the roof and ribs with material handling. This is the first Fletcher® six head machine to be designed and built for the mines in the United States. The machine is intended to work in the Illinois Coal Basin. The objective was to produce a machine capable of drilling and installing six bolts simultaneously with a limited number of operators. The goal of the mine is to decrease the time to bolt a cut to improve the safety level of the current roof bolting method, improve efficiency and to improve the bottom line cost of entry development. The customer wanted four mast feed drills at the front of the machine dedicated to installing roof bolts and then another two mast feed drills behind them dedicated to rib bolts. This dictated the requirement of latched controls, which would allow the operator to start drilling one hole and then latch the controls to be able to move on to the next. To accomplish this, we developed a unique hydraulic latch circuit to maintain operator safety and compliance. Guarding was added to prevent an operator from coming into accidental contact with a latched drill. The result of the design is a machine with a single platform and six independent masts with drillheads: four masts strictly for drilling and installing roof bolts on the front of the platform and then two masts on the back of the platform for rib bolts. The feed and rotation controls at each operator’s station include a latch control for drilling. The latch control will allow the operator to lock in the feed and rotation once the hole has been collared, allowing the operator to move on to the next hole. The rear of the machine is equipped with material handling. There are two material pods with winch controls as well as a mesh rack that includes mesh lift, mesh tilt and mesh sump. The six-head roof bolter allows fewer operators to drill and install roof and rib bolts, which in turn lowers the miners’ roof exposure per cut. This design reduces the operator’s exposure from the inherent pinch points and rotary hazards once he has engaged the latch drilling. Therefore the machine will help to decrease the time to bolt a cut, improving productivity while enhancing the ability to operate the machine safely. INTRODUCTION When mining underground it is necessary to support the roof quickly to prevent it from collapsing after an area has been mined. Since the 1950s, the primary method for supporting the roof has been the installation of roof bolts. Roof bolting is one of the most basic functions yet one of the dangerous jobs in the underground mining operation (1). The Mine Safety and Health Administration’s (MSHA) Health and Safety Accident Classification injury database showed an average of 660 roof bolter operator accidents per year over a 5-year period (1999-2003) (2). The numbers show that roof bolting is the most hazardous machine-related job in underground mining. It represents 39 percent of all machine-related accidents in underground coal mines. In 1993, the U.S. Bureau of Mines conducted a study that has shown the activity of drilling as the most hazardous job task performed by a roof bolter operator, accounting for 31 percent of all roof bolting injuries (3). Almost half (46%) of these drilling injuries were due to falling rocks or coal from the roof. All of these injuries occurred under supported roof. The majority of these injuries (about 99%) are not caused by a major roof collapse but from falls of smaller rock from the immediate roof. This type of roof failure has also been termed “skin fall.”"

Jan 1, 2017

By S. Anderson

Advances in inexpensive computer automation led to the development and utilization of a computerized ore control system at Cyprus Coppers tone Gold Mine near Parker, Arizona. These new ore control practices improved accuracy, performance, and productivity of the ore control effort. An automated system for data collection, including bar coding of blast hole samples, laboratory analysis, data management, grade estimation, cut delineation, and ore zone stakeout, plays a major role in ore control practices. This is of particular interest because of the large amount of blast hole information being processed, analyzed, and reported daily.

Jan 1, 1991

By A. Rai

"This paper provides an overview of the current use of auxiliary ventilation product and the challenges with limited air quantity in dead-end entry or working face. The PVC low frictional factor, low physical constraint and minimum leakage ventilation duct was development with ""made in US and used in US"". The PVC duct development covering operational and total cost of ownership with on-going success will be presented. This paper will discuss mine sites using new PVC vent duct underground and the results from operational and technical side making a difference. INTRODUCTION The Turquoise Ridge Joint Venture (TRJV) is located in northern central Nevada, and is situated within the Basin and Range province, near the northeast end of the Osgood Mountains (see Figure 1). The TRJV mine consists of typical Carlin type- gold mineralization characterized by low strength rock of altered limestone’s, siltstones, and mudstones. The weak nature of the ground facilitates the underhand cut and fill mining methods [3].Mining Method; Underhand cut and fill : The mine uses underhand cut and fill method which has 12’x12’ top cuts and several different size undercuts. The ore body is accessed off of a secondary development heading, utilizing a heading with a cross section of 14W x 14H or 15W x 16H configuration. In the wider and more massive zones, two headings in a production panel may be worked at any one time. Drift round lengths are determined by the type of drilling machine being used. An example of a typical topcut and associated undercut layout is shown in Figure 2. SECONDARY / AUXILIARY VENTILATION IN UNUNDERGROUND METAL MINES The auxiliary ventilation system provides the required air volumes at the face of dead-end developments and production workings, which in many cases may be considered as the primary method of assuring that the air quantity and quality standards in these working areas are satisfied. The Auxiliary fans and ducting systems are usually the primary means of delivering the required air volumes to the face of dead-end developments and production workings. Both centrifugal and axial-flow fans are used in underground auxiliary ventilation systems, usually electric powered. The internally direct driven axial-flow fans tend to be more popular because of their compactness and adaptability to staging. The most commonly used materials for ridged tubing are coated steel, alloyed steel, fiberglass and resin. Flexible (collapsible) ventilation tubing is also used and is usually made from neoprene-coated or nylon material. To add stiffness and reduce collapsibility these fabric ducts can be formed over a steel spring frame. A very important factor in the design of an auxiliary ventilation system is to minimize leakage and reduce the frictional pressure losses along the auxiliary ducting systems by minimizing their friction factors (K)."

Jan 1, 2015

By Y. C. Kim

The results from a retrospective study are described in this gaper in which she past development drilling activities were investigated using geostatistics. The purpose of the study was to determine the amount of savings in drilling cost that could have been realized through the optimal placement of sequential drill holes using geostatistics. Out of 144 DDH's that were in place within the study area, the results showed a possible elimination of 34 DDH's without any reduction on the confidence interval of the global reserve estimates. If the incremental savings from one drilling campaign to the next were considered, however, the amount of percentage savings were even greater. Other interesting results from this study were; 1) tangible demonstration of the importance of a proper geologic delineation within the study zone, and 2) the robustness of the obtained experimental variograms from the rather early stage in development drilling.

Jan 1, 1981

By J. G. Asbury

Broadly conceived, the demand for electricity depends upon three sets of variables: (i) the growths of the many individual demands for energy services; (ii) the competitiveness of electrically driven technologies in meeting these demands; and (iii) the energy-conversion efficiencies of installed electrical technologies. The first set of variables establishes the size of the potential market; the second, the market penetration of electrical equipment; and the third, the quantity of electricity required to operate the equipment. All forecasts of electricity consumption ultimately depend upon inferred or assumed relationships to describe the future behavior of these variables. This partitioning of the demand-forecasting problem is conceptually useful and will guide the discussion presented in this paper. However, it is also something of an oversimplification. Examined in more detail, the electricity fore-casting problem is exceedingly complex. The variables mentioned above are, in turn, found to depend upon more fundamental sets of demographic technological, resource, and policy variables. The demand projections developed by the major forecasting services are usually developed in terms of these underlying variables, which themselves must be independently forecast.

Jan 1, 1985

By R. B. Lantz

Low Froude Number (Fr) theory* predicts that stably-stratified fl& around a terrain obstacle will divide into a lower layer passing essentially horizontally around the obstacle and an upper layer passing essentially over the obstacle. The prediction was formulated by Sheppard (1956) and Drazin (1961) and confirmed experimentally in the towing tank model d experiments of Hunt et a1 (1978) and the atmospheric full scale experiments of the US EPA Complex Terrain Model Development Program (1982- 1985). The US EPA Complex Terrain Dispersion Model, currently under development, employs the layering principle with the flow in each layer calculated independently by potential flow (PF) theory after the layer thicknesses are established according to a simple function of Fr, i.e., Hc /H = 1 - Fr where Hc is the dividing streamline freight and E is the obstacle height. Use of PF theory in the CTDM is attractive because numerical solutions can be obtained simply and economically, as compared to lengthy Navier-Stokes (N-S) solutions, but realism is sacrificed in creating a surface of discontinuity between the tm layers and eliminating the effects of shear and gravity in each layer.

Jan 1, 1986

By P. Geoffrey Feiss

The Piedmont province of the southern Appalachians is becoming the focus of interest for many exploration geologists. In the past, only those deposits with significant surface exposure have been exploited. Thus, few deposits have been found and relatively little exploration has been conducted in recent years. Modern geochemical and geophysical techniques can alleviate this problem of concentrating on exposed ore bodies by allowing us to "look through" the soil and saprolite to detect the presence of significant mineralization at depth. This paper will attempt to evaluate the feasibility and effectiveness of several geo¬chemical exploration techniques in the Piedmont, of Cabarrus and Stanly Counties, North Carolina. The area chosen for the study is shown in Figure 1, lying almost wholly within the Mt. Pleasant quadrangle, North Carolina. The area is on the eastern boundary between the Charlotte belt, a zone of plutonic and intermediate grade metamorphic rocks, and the Carolina Slate belt, a series of complexly interbedded volcanic and sedimentary rocks of predominantly low grade metamorphism. The area is now considered to be a 500 million year old active, continental margin.1 As is typical of most of the piedmont, outcrop is sparse. Figure 2 is a sketch map of the general geology of the area under study, showing the Charlotte belt rocks in the northwestern quadrant and slate belt rocks, to the east. Within the area are a number of old mines and prospects, the most famous of which are the Furniss and the Phoenix mines in Cabarrus County. All are reported to have contained Au and Cu. Ag and Pb were reported from some. A summary of the deposits is given in Table 1. Data used in this study are from three Master's theses conducted at the University of North Carolina at Chapel Hill. 3,3,6 In separate studies, well waters5, B-zone soils3, and vein and float quartz6 from the area described were sampled and analyzed. Each study concluded separately that geochemical anomalies in the vicinity of the ores justify use of that specific sample type in a geo-chemical exploration program. However, no comparative study of the methods has

Jan 1, 1977

By C. L. Molina

The U.S. Geological Survey (USGS), in cooperation with the Bureau of Land Management (BLM), Geological Survey of Wyoming, and U.S. Bureau of Mines (USBM), will produce an estimate of the amount of available coal in an area about 55 Ian (35 miles) south of Gillette, Wyo., where the Wyodak coal bed is 8-27 m (25-90 ft) thick. Available coal is coal that actually is accessible for development under current regulatory, land-use, and technologic conditions. Local coal-development considerations include roads, ranches, railroads, pipelines, power lines, wildlife and archaeological sites, alluvial valley floors, cemeteries, and the Hilight oil and gas field and gas plant. Some of these considerations would be mitigated so that surface mining may proceed; others presently preclude mining in their vicinity.

Jan 1, 1995