Search Documents

By Mark E. Smith

To allow recovery of gold values from ore which cannot be economically processed by the mill, Pinson Mining Company has developed a run-of-mine heap leaching facility. In order to estimate production scale recovery rates, reagent consumption and percolation problems, a series of pilot scale tests were performed. These tests typically consisted of 3,630 metric tons (mt) (4,000 tons) leach ore at a grade of .94 to 1.56 grams per metric ton (g/mt) (.03 to .05 oz.) Au/Ton. Test heaps were loader stacked to approximately 4.3 meters (14 feet) high. Information from these pilot scale tests was employed in the design and construction of the production scale facility. Parameters such as spray rate, leach cycle, sprinkler placement, and barren solution chemistry were determined by the pilot tests.

Jan 1, 1983

By S. Middlemiss

The Indentation Fracture technique is being developed as a tool for use in comminution and mineral liberation analysis. Fracture toughness measurements for a number of mineralogical materials were made and comparisons were drawn between these and properties measured with the Ultrafast Load Cell drop weight apparatus. The technique has also been used as a probe to quantify differences in fracture properties at different areas in the microstructure of a material. In both a Utah limestone and a South African quartzite, material near a grain boundary fractures very differently to that in the bulk. Ongoing work is ultimately aimed at producing a comprehensive fracture model for a multi-mineral system based on its micro-fracture characteristics.

Jan 1, 1994

By Atmesh K. Sinha

Death and injury rates in mining have been the highest of any industry; the injury severity rates in mines have also been the highest. Tentative figures reveal that 1971 was the best year yet for the bituminous coal indus¬try with the lowest number of fatal accidents. Nevertheless, 177 men were killed at a frequency rate of 0.76 per million man hours. Coal mine accident statistics have been described at various times as unacceptable and intolerable and recently resulted in the enactment of massive legislation. The 1969 Coal Mine Health and Safety Act was passed by Congress "to improve the working conditions and practices in coal mines and to prevent accidents and occupational diseases originating in the coal mining industry." The prevention of accidents in coal mines is the statutory responsibility of mining engineers and the moral responsibility of all who have any part to play in mining coal. The questions to be answered by these men may well be - What are the reasons for the high accident rate? Are the mines as safe as they can be? Are our mines sufficiently manned to insure proper supervision of production cycles and safety requirements? Are our plans for safety committees, safety campaigns, and safety inspections sufficient? Are they producing the results intended? If not, how can these be reorganized to have a greater impact? What is the real cost of an accident? What are the immediate and long-term plans for further improvements? These questions are in no way exhaustive, and the answers are not easy. There are many aspects of mine safety, and any one of them can be the subject of a lengthy discussion. The aim of this paper, therefore, is to limit the analysis to documented fatal electrical accidents in mines so that meaningful conclusions for improvement in electrical accident-experience statistics can be made. In doing this, it is also the intention to emphasize areas of missing information and propose a few suggestions for better hazard analysis.

Jan 1, 1972

A parametric study was conducted to establish the optimum operating conditions for the column flotation of fine coal. The parameters examined in this investigation included collector and frother dosages, feed solids content, and the volumetric flow rates of feed slurry, air and wash water. Despite the wide range of conditions studied the experimental data were found to fall along single grade-recovery curves, just below the maximum separation predicted by the release analysis technique. The deviation of the parametric test data from the release curve was attributed to the nonselective entrainment of mineral matter associated with poor froth washing. The operating point on the characteristic recovery-grade curve was found to be primarily determined by feed rate and aeration rate.

Jan 1, 1992

By D. L. Moellenberg

Under various state laws enacted mostly within the last 20 years, reclamation requirements and standards for hard-rock mining operations have been established virtually everywhere in the western United States. Unlike the uniform and detailed coal mine reclamation requirements under the federal Surface Mining Control and Reclamation Act ( "SMCRA" ) and state programs mode led after SMCRA, the various state law hard-rock mine reclamation requirements are based upon a variety of objectives, and therefore are subject to varying standards from state to state. While the diversity of reclamation requirements complicates the determination of what reclamation measures will be required at any particular mine, there are valid reasons for this diversity. There are dozens of different commodities mined in the United States, and mining methods are different for each commodity. Local natural conditions such as climate, precipitation, geology, hydrology, and biology vary widely across the county. Site-specific conditions also affect mining and reclamation methods. Also, factors such as economics, land use, and environmental protection issues receive different priorities in different states and communities within those states. State reclamation requirements in general provide the flexibility to consider site-specific circumstances, allowing operators to design and engineer the best reclamation measures for each mining site. To the mine developer or manager, reclamation requirements must be translated into design, operational, and closure measures for mine planning. Each of these measures must then be assigned additional costs to be factored into the economic decisions for a particular mining operation. On a broader level, reclamation costs must be factored into decisions such as where to invest in exploration and mine development. The purpose of this paper is to provide a summary of the state non-coal mine reclamation requirements in twelve western states. This summary comparison may be useful as a starting point in considering how local reclamation requirements will impact potential mining costs.

Jan 1, 1994

By Mark C. Williams, Shunsuke Managi, Noriko Hikosaka Behling

Particle processing is a key to using solid particles in fuel cell applications. Selectivity with regard to reactivity, impurities, etc. is an important feature and the treatment of particle surfaces could greatly impact the performance of direct carbon fuel cells. Solid fuel particles will become increasingly important in the future. Present energy conversion systems for solid fuels are too inefficient. New energy conversion systems for solid fuels with higher energy conversion efficiencies are possible. Fuel cell technology is a key technology in these new conversion systems. The direct carbon fuel cell (DCFC) operates on carbon particles obtained from a variety of solid fuel feedstocks. The DCFC is the only fuel cell designed to directly oxidize carbon particles in a special anode chamber. The particles are generally graphite structure with high purity. The electrolyte used is the high temperature solid oxide, molten carbonate, or hydroxide electrolyte. Since a pure stream of CO2 is produced, the stream can easily be sequestered and disposed. Pure carbon dioxide produced as a by-product would also have a market in many industries. A well-defined technology roadmap identifying key research and development (R&D) issues is necessary to provide a framework for the development of these systems and to prevent entrenchment in inherently inefficient technologies. This review paper describes the direct carbon fuel cell and its system, how it works, the developmental status, the characteristics of the carbon particles needed, and the research and development issues for the technology

By Jerome F. Sheldon

The earliest recorded history in the use of belt conveyors in the United States is in O. Evans' "Miller's Guide" published in Philadelphia in 1795. Evans defines a conveyor as a "broad endless strap of thin pliant leather or canvas revolving over two pulleys in a case or trough." (Ref. 1) In this definition, pulleys are being used in a bulk material belt conveyor application. Pulleys used in belt drives can trace their origin back to 1200 A.D. In fact, Engineers had considerable experience designing them into drives transmitting greater horsepower than those used in the early belt conveyors. In belt conveyor application, a pulley's purpose is primarily three-fold, 1) support the belt in directional changes, as designed in the conveyor, 2) transmit driving power to the belt, and 3) guide or train the belt. There are various types of pulleys used in belt conveyor systems and these are thoroughly covered in "Belt Conveyors For Bulk Materials" prepared by CEMA, 1966. For our discussion, however, the most common used in belt conveyors are drive pulleys, snub pulleys, head pulleys, tail pulleys, takeup pulleys and bend pulleys. The drive pulley imparts the driving force to the belt and may be located at the head or discharge end of the conveyor, in return strand, or at the tailor loading end of the conveyor. A snub pulley is located near the drive pulley to provide more arc of contact between the belt and pulley for maximum

Jan 1, 1971

By L. A. Garfield

Since the start of mining operations at White Pine in 1953, over 22 miles of drifts have been driven for the purpose of developing the ore body. The drifts, normally driven in multiples of three or five headings, serve as conveyor belt routes, ventilation ducts, equipment and haulage roads, and initial access to mining blocks. Development openings in the flat-lying, bedded ore body are driven in rectangular section from 16 to 32 feet wide and from 8. 5 to 16 feet high. The floor level normally coincides with the bottom limit of the chalcocite values and the roof or back is carried at the most competent stratum adjacent to the top of the ore. A development front consisting of five headings and associated crosscuts is advanced at an average rate of about 100 feet per month using conventional drill and blast techniques and equipment. The cyclic nature of the functions involved in driving the openings and the need to include them in production schedules preclude significant improvements in advance rates using current drill, blast, muck, and haul sequencing.

Jan 1, 1969

By David D. Lambert

REE analyses of cumulate plagioclase from the PGE ore zone of the Stillwater Complex indicate that pressure fluctuations in the magma chamber acting on a single magma can- not be responsible for features such as the reappearance of Mg-rich olivine on the liquidus. The data is more consistent with a model involving multiple injection and mixing of geochemically distinct magmas. The PGE bearing sulfides of the J-M Reef are associated with such a re- appearance of olivine, indicating that the unusual location of the ore zone may be related to the addition of new magma, compositionally distinct from magmas that produced cumulates in the Ultramafic zone of the complex.

Jan 1, 1981

By Robert E. Mead

During the past three years the New York Trap Rock Corporation has been restricting blasting operations to days when favorable atmospheric conditions prevailed. By favorable atmospheric conditions is meant the absence of temperature inversions or isothermals in the lower atmosphere or under 6,000 feet altitude. Strong wind and wind shear can also cause conditions unfavorable for blasting. As a result of this practice, there has been a marked decrease in the number of blasting complaints received. The New York Trap Rock Corporation operates four stone quarries on or near the Hudson River within 60 miles of New York City. The Company supplies approximately 7,080,000 tons of high grade, crushed and graded aggregate, rip rap and by-products to the New Pork City area annually, This stone is carried to the market by a fleet of company owned deck &cows which are moved by tugs of a subsidiary towing company. Stone from two of the quarries is diabase: and, from the remaining two, dolomite.

Jan 1, 1962

By Brian Stimpson

A recent study by the National Academy of Engineering concluded that if the U.S. Coal Industry is to double production by 1985 it must open 30 new 2,000,000 tons per year surface mines in the eastern states and 100 new 5,000,000 tons per year surface mines in the western states, in addition to major growth in underground mining. Major expansions in coal mining are also planned in other countries. Engineering geology can play an important part in coal mine development, operation and abandonment (Table I), and with the increasing scale of surface coal mining and the requirements of environmental legislation, it seems certain that engineering geology and geotechnics will play a growing role in surface coal mining.

Jan 1, 1976

By Ihsan Berk Tulu, Mark Alexander Van Dyke, Deniz Tuncay, Ted M. Klemetti

Bleeder entries are critically important to longwall mining for the moving of supplies, personnel, and the dilution of mine air contaminants. By design, these entries must stay open for many years for ventilation. Standing supports in moderate cover bleeder entries were observed, numerically modeled, and instrumented by researchers at the National Institute for Occupational Safety and Health (NIOSH). The measurements of the installed borehole pressure cells (BPCs), standing support load cells and convergence meters, and roof extensometers are presented in this paper in addition to the numerical modeling results and visual observations made by the NIOSH researchers in the bleeder entries. The results include the effects of multiple panels being extracted in close proximity to the instrumented site as well as over one and a half years of aging. As expected, standing supports closer to the longwall gob showed the greatest load and convergence. The roof sag appeared generally independent of the proximity to the longwall gob. The BPC readings were driven by both the proximity to the gob and the depth into the pillar. The results of this study demonstrated that the entry roof can respond independently of the pillar and standing support loading. In addition, the rear abutment stress experienced by this bleeder entry design was minimal. The closer the mine development, pillar, or supports are to the gob, the greater the applied load due to rear abutment stress.

Jan 7, 2021

By M. S. Prasad

This paper presents the process methods of beneficiating various copper-cobalt and copper-zinc ores mined by Gecamines in Zaire. Geology and mineralization of both sedimentary and vein type deposits are described with special emphasis on the production of oxide, dolomitic and sulfide concentrates. Description of different types of concentrators and their treatment methods are discussed for the production of sulfide, oxide and dolomitic concentrates. Production of concentrates, their consumption and stocks are briefly reviewed. Modernization of the concentrators with substantial investments on grinding, classification, flotation methods and tailings treatments are also discussed to improve the metallurgical efficiency of the concentrators with a view to improve the production of concentrates both qualitatively and quantitatively.

Jan 1, 1990

By Samuel S. M. Chan

Rock surrounding mine openings frequently is an impermeable type such as shale or granite. Most rock, however, has joints, bedding planes, cleavage planes, or other potential discontinuities. Permeability to fluids (gas or liquid) may exist via natural joints or fractures in an otherwise impermeable rock. In the mining situation, tectonic and induced tensile and shear stresses may be great enough to cause joints to open or fractures to develop in previously solid rock. The rock, as a result, becomes less self-supporting and may - require artificial support such as rock bolts or timber. Simultaneously, as fractures develop, permeable paths may be created. If fluid can be injected into a previously solid and impermeable rock mass, a logical conclusion is that a fracture (crack) flow path must be transmitting that fluid. The U.S. Bureau of Mines Laramie (Wyo) Energy Research Center has been evaluating results of in-situ oil shale fracturing (hydraulic or explosive) and retorting experiments by. a fluid (air) injection , and borehole air flow profile logging technique since 1956 (1, 14, 15). In the oil shale case, it is imperative to know the location and flow capacity (permeability) of natural fractures, if they exist, and induced fractures that inter-connect vertical wellbores at depths of fifty to several hundred feet. By injecting air into one wellbore in a system of several wells and measuring input volume and pressure while simultaneously measuring the output of other wellbores, the minimum areal extent of interconnecting permeable fractures can be determined. Exact locations (depths) of fractures and individual fracture flow capacities between wellbores can be determined by air flow profile logging (14, 15). Knowledge of fracture locations and permeability is essential to rational experimental in-situ retorting design.

Jan 1, 1973

By Albert J. Kritscher

The Similkameen Copper Project located near Princeton, British Columbia, is operated by the Similkameen Mining Company Limited, a wholly-owned subsidiary of Newmont Mining Company. The orebodies for this project are located on both sides of the Similkameen River for which the project is named. The project involves the processing of an average of 15,000 STPD of andesitic ore, mineralized largely with Chalcopyrite, at an overall plant availability rating of 90 percent. Project life is nominally 15 years. Design for the plant and its ancillary facilities was undertaken by Bechtel Corporation with procurement and construction management by Canadian Bechtel Limited. Construction began in June 1970 and first ore was introduced into process in March 1972. This paper concerns itself only with the project tailing system. The processing plant is located on a bench of glacial stream gravels which overlooks the river canyon. This site represented the only relatively flat area of sufficient size to accomodate processing facilities near to the ore- bodies. Reference is made to Figs. 1 and 2 showing the relationship of project features in plan and profile.

Jan 1, 1973

By John E. Young

United States Steel Corporation's Winifrede Mine is operated by Lynch District in the mountainous region of Eastern Kentucky. This region is characterized by narrow mountain ridges and precipitous slows which present both an opportunity and challenge in the design and selection of coal handling facilities for the movement of coal from the section belts to the railroad cars. The narrow finger ridges precluded use of underground haulage and, thereby, presented the opportunity to use high capacity equipment on the outside bench. The precipitous mountain slopes, steepest at the Winifrede seam horizon, presented a challenge to select a solution for lowering the coal approximately 1000 feet from the seam level to the valley floor railroad load-out point. It was evident from the start of planning that these two factors predominated; namely, rail haulage and coal lowering, and solutions to these would determine the final design of the Winifrede Mine coal handling facilities.

Jan 1, 1970

By RENE GOMEZ, RAUL CASTRO

Estimation tools and models are now available to estimate fragmentation, but some variables have yet to be studied to understand their effect on the fragmentation process. One such variable whose mechanisms have yet to be studied is the residence time, which in block caving directly depends on the distance that fragments travel from their original position in the broken ore to the drawpoint. In this study, granular material fragmentation was characterized during its flow to understand its characteristics and mechanisms. The results show that the breakage of fragment singularities occurred mainly within medium and smaller sizes, increasing fine material during flow. Thus, the main fragmentation mechanism in experiments was identified as abrasion between rock fragments where fine material continuously increases as distance increases in spite of the high rock strength and the piston flow movement used. The results presented here can be applied to incorporate fragmentation during flow of large travel distance of ore such as in block caving.

By Sandro Moro, Giuseppe Tiberti, Giovanni Plizzari, Antonio Conforti

"During TBM operations, thrust jacks apply high-concentrated forces to the last installed precast segment. These loads generate a disturbed region in the precast segment under the thrust jacks, in which significant tensile stresses (defined as splitting or bursting stresses) occur perpendicular to the load direction. In addition, due to the demand of compatibility, the combined effect of TBM high-concentrated loads determines tensile spalling stresses in the area far from the loads. Therefore, local rebars or fiber reinforcement are required in these areas. This paper focuses on the study of the effects generated by high-concentrated loads exerted by TBM hydraulic jacks, mainly in terms of both spalling and splitting phenomena. Experimental tests on small-scale specimens showed that polypropylene fiber reinforcement significantly enhances both the bearing capacity and the ductility. Moreover, polypropylene fibers resulted in very effective control of compatibility cracks.INTRODUCTIONTunnel segments are generally reinforced by conventional rebars (RC segments) in order to resist the tensile stresses both at Serviceability (SLS) and Ultimate Limit States (ULS).In the two last decades, Fiber Reinforced Concrete (FRC) has been used in many precast tunnel segments (sometimes also in combination with conventional rebars). Steel Fiber Reinforced Concrete (SFRC) is generally used for these applications even though there is a growing industry interest on macro-synthetic fibers for structural applications. Conforti et al. (2015) showed that polypropylene (PP) macro fibers can be used as shear reinforcement in both wide shallow and deep beams. Referring to precast tunnel linings, very few early experiences are reported in literature. Bonalumi et al. (2015) developed full-scale tests on tunnel elements reinforced by PP fiber reinforcement and conventional rebars (hybrid solution). The design process of segmental concrete tunnel linings generally models the standard load cases of demolding, storage, transportation, positioning and embedded ground condition. In all these stages the ring can be modelled as simple curved beam elements (having a height equal to the lining thickness and a width equal to the segment length). During these loading conditions, flexural demand is generally limited; thus, in case of conventional RC elements, a rather low ratio of longitudinal curved rebars is usually adopted (?s of about 0.2-0.3%)."

Jan 1, 2016

By Virgil A. Bilyeu

The Pan American Mine, in southeastern Nevada, is about 26 miles west southwest of Pioche, Nevada, and about 266 miles southwest of Salt Lake City, Utah. The mine is located in the Comet Mining District, and since the ore occurrence is generally the same in the Comet and well known adjacent Pioche Mining Districts, the history of the two shall be considered the same. The Pioche District began about 1869 with the production of high grade gold and silver from fissure veins in the Cambrian Prospect Mountain quartzite. Peak production was reached in 1872 and then declined with sporadic production until 1924, when Combined Metals Reduction Co. shipped its first, complex sulphide ores mined from the CM bed at Pioche. Extensive ore bodies in this CM bed attracted interest in the same bed in the Comet District. Small pockets of high grade silver-lead were mined from fissures cutting the CM and other limestone beds above. Exploration in the CM beds at this time proved a large area of mineralization too low grade to be considered ore.

Jan 1, 1967

By Paul H. Rydlund

The wide use of bulk ANFO in surface coal mines is questionable in our energy conscious environment. At many locations, bulk ANFO is not the proper economic selection. Water conditions, energy requirements, waste and spillage, and vibration control are factors too often overlooked in the proper choice of blasting agents. Cost savings over 20% have been realized by converting bulk ANFO to packaged blasting agents. Future trends suggest greater concern for energy conservation in blasting will limit bulk ANFO applications and promote packaged products where quality can be maximized, waste and spillage eliminated, and water compatibility in wet areas assured.

Jan 1, 1980