Search Documents

Geostatistics is well known as a tool for ore reserves calculations at the exploration stage. The goal of this paper is to show geoscatistics can also contribute to productivity gains, allow better selection of the mining methods and better control of the grades during production. The first two examples show how geostatistics can provide sophisticated models, using conditional simulations and the use of them for simulations or optimizations of mining processes. A third example will show how to use geostatistics for short term planning in a large polymetallic vein type mine.

Jan 1, 1983

By Louis W. Towle

A brief history of the use of Ammonium Nitrate in explosives and blasting agents is given. Methods of manufacture and physical properties of the various types of Ammonium Nitrate are given with particular reference to their use in blasting agents Important properties of blasting agents discussed are sensitiveness, methods of initiation, velocities of detonation, strength, density, products of detonation, rate of pressure development, and borehole pressure.

Jan 1, 1959

By G. Van Weert

Separation of minerals by shape has received little attention, since minerals normally do not break into different shapes during crushing and grinding. However, comminution of consumer wastes generates opportunities for novel separations based on particle shape. For instance, ductile plastics are broken into longer curved shapes, whereas brittle plastics yield angular particles. Using spouting beds for particle separation in water requires controlling the spout's instability. The preferred geometry for such redesigned spouting beds is reported. Plastic cylinders, discs and spheres were separated as a function of rising water velocity and amount of particles in the system. By using 5 mm particles, differences in settling behavior could be video recorded.

Jan 1, 1999

By H. Lyn Bourne

This is the sixth annual tabulation that gives mineral royalty information. This tabulation, like the previous editions, includes all of the earlier data plus more than 100 new entries. In addition to the royalty information, some entries show the cost of purchased reserves. An article in the December 1984 Kentucky Coal Journal could have far reaching applications. It explains that a banking firm examined the "reserve risk" as one of six factors for analysis when financing a coal project. The firm concluded that coal reserves in Kentucky are worth an average of $0.29/t ($0.26 per st) in-place. The banking firm based this in-place value on its examination of more than 50 leases. In-place value is especially important when trying to establish a mineral value for a given deposit. Ernie Lehman wrote to this author after last year's column appeared and he quoted the lease rates for lead and zinc on federal land. He states, from first hand information, that the leases are based on a percentage of net smelter return as follows: 4% for the first five years, 4.5% for the next five years, and 5% thereafter. The figures used in last year's column ($ per st) came from dividing reported royalty income by reported production. The information reported last year merely translates the results of the net smelter return (as written in the lease) to royalty income per ton to the US Government for the various years. Statistics from the Minerals Management Service of the Federal Government show that oil and gas account for 40% and 53%, respectively, of the Federal royalty income. Coal accounts for about 4% and all other minerals, the remaining 3%. Oil and gas leases are mostly at 12.5%. Most of the coal leases are at 12.5% for surface mining operations and 8% for underground mining. Many of the other commodities are leased at 5%, which has been true for decades. Relative to Federal leases, this year's table shows some percentages and some costs per ton. This was done to give information about the leases and also to show income produced by various commodities. Note that some commodities have a variation in $/ton even though the royalty percent is the same. These variations result from a combination of factors that influence the value of a mineral commodity. The same caveats that have appeared in previous columns relative to factors that influence the value of reserves are restated. The data in the table serve as a general reference and are not intended to present an absolute scale of reserves costs. Several factors influence the value of any mineral commodity. The factors include: • location/transportation (especially significant for most industrial minerals); • market conditions both for the commodity and the company acquiring the right to mine it; *quality or grade of the deposit as it reflects the amount of processing/beneficiation necessary to produce the finished product; and • legislative restrictions and conditions for mining a given material at a given site. These and other factors will significantly influence the cost of reserves. The table shows the range of royalties and the variations in the basis of computing the fees. In a few instances, it gives the cost of acquired reserves based on purchase price and quantitative estimates of the material in place. The table lists the commodity in column 1, and the subsequent columns give the location - either by state, US geographic area or Canadian province; the cost - R for royalty and P for purchased cost; and the year in which the lease or purchase agreement occurred. The last column offers either comments or gives a footnote number for more information. The cost column requires more explanation. The units may refer to cubic yards (/yd), cubic feet (/cu ft), tons (/T, 2000 lbs) or acres (/A). 1 cu yd = 0.7646 m3 1 cu ft = 0.2832 m3 1st=0.9078t 1 acre = 0.4047 hm or m2 In several cases, the royalty is a percentage of the sales price of the finished product and is levied against either the amount produced or the amount sold. We thank those who contributed information for the table: G. Anderson, B. Brown, R. Ganis, K. Hauser, E. Lehman, and S. Sims. Their help is appreciated as are the contributions by those who asked to remain anonymous. This column requires additional information each year. That data must come from people in the minerals industry who have royalty information. What appears in the table is only a very small fraction of the cost information relative to the various commodities and the geographic areas for which there is royalty information. If you find this column of interest and possess information write the author at the address given in the author's box or call 313-462-0005.

Jan 7, 1988

By Steve Wirch, Robert Jankowski

The issue of dust control in underground coal mines has been extensively studied by both government and industry. This research work has resulted in many techniques which control the dust or help miners avoid it. Control techniques either prevent the dust from becoming airborne or cleanse the air before it can be inhaled. Avoidance measures minimize the exposure of miners to the airborne dust by blowing the dust away from work areas or making it unnecessary for a miner to occupy a dusty region. One of several successful dust control measures in continuous miner sections is the use of a machine mounted scrubber which cleanses the air and helps to prevent the contaminated air from reaching areas frequented by mine personnel. Research on the application of scrubbers on longwall shearers began in the 1970s and continued into the 1980s. The most successful projects showed only moderate improvement when a scrubber system was mounted on a longwall shearer, and the less successful projects actually increased worker dust levels. There are many reasons that scrubbers have not been successfully applied on longwalls. The most significant of these is that longwalls have across the face ventilation and generally have high face air flows. Scrubbers tend to work best when they are the primary cause of ventilation. Therefore, their capture efficiencies on longwalls tend to suffer because of the exposure of the drums to the primary airflow. Other reasons scrubbers have not been implemented on longwall s include the successful application of an excellent water spray system, effective cutting techniques, and dispersion of dust sources. These techniques can help control drum generated dust, increase production, and limit the relative effectiveness of a scrubber.

Jan 1, 1995

By R. Tamir

This paper will describe the benefits of utilizing the decision support system, DSS to support the methodology of structured decision-making in the mining environment. It will outline the layers of the mining related decision making – 1. Creation of “one truth” situational awareness utilizing 2. existing planning, ERP, operational and monitoring agents, a. Expressing plan verse performance across mining phases and functions compared with the actual and trends to evaluate performance. b. Creating alternate courses of action and the implications up and downstream. 3. It will review the current condition were although a multitude of technologies resolve multi variable issues they do not interact in a way that assists decision makers throughout the organization in making high-quality decisions that will push the overall performance envelope. 4. The paper will show the benefits of integrating military methodologies to resolve multi variable complexed issues (operational, financial and other), operating in changing environments in order to meet time sensitive objectives with restricted resources. This is achieved by creating a shared situational awareness thru incorporating information from a multitude of data generating agents, creating COA, selecting the appropriate and turning it into a plan. The paper will discuss the implementation and suggest a path.

Feb 1, 2023

By Chris Roos

The mining industry has made strides in planning for operations to be safe for the workforce and public, to protect the natural environment, and to maximize value for shareholders. However, many of the techniques used to accomplish these goals are based on estimated models of mineral content, production efficiency, and economic performance. The industry has begun to recognize the need for understanding the uncertainty in these models, how it affects their decisions, and what the potential impacts are for each project. The challenge has become how technical professionals can effectively communicate the impact of this uncertainty and its importance to both technical and non-technical audiences. This paper presents mining engineers (and other technical professionals) with traditional and modern principles of data visualization and technical communication that can assist with communicating the effects of uncertainty in the mine planning process.

Jun 25, 2023

By Douglas W. Barr

Water is a necessary part of our environment. It is a biological necessity, but more than that, it is a necessary part of our life style. Those of us who live in the north woods expect water to be part of the scene. There are few natives of this region who would be content to eliminate the streams, the lakes, the marshes, or our forests. Throughout the world, water has been so much a part of man's environment and man's adaptation to life has been so closely tied to water that our way of life and ways of accomplishing our work include water as an essential tool. The production of taconite is an example of our dependence on water. Other methods could have been developed to process taconite ore but the process methods chosen utilize water. Water is used for grinding and separation and for trans- porting the ore from one part of the process to another and for dust control. A typical large plant producing 10 million tons of taconite pellets per year will have on the order of 130,000 gallons per minute (8.202 m 3/51 of water in circulation in the plant. About 120,000 gal. per min. (7.571 m 31s) will pass to tailing thickeners where 110,000 gal. per min. (6.940 m 31s) is separated from tailing and returned to the process. About 15,000 gal. per min. (.9464 m 31s) goes with thickened tailing to tailing basin. My point is that there are great volumes of water in motion in a taconite plant,

Jan 1, 1980

By Magnus Ericsson

The unexpectedly quick recovery in world crude steel production in the second half of 2009 was due almost entirely to increased production in China that began in late 2008. Previous peaks in monthly production in China were matched by April 2009. The rest of the world had still not reached pre-crisis production rates by May 2010. Chinese production drives growth, but there has been some growth in most other larger crude steel producing countries as well, compared to production in 2009. If the production rate of the first four months of 2010 continues, the total output of crude steel in 2010 will be somewhere around 1,410 Mt (1.5 billion st), the same as in the record year of 2007.

Jan 1, 2010

By A. H. Srnallbone

Over the past few years the rising production costs, shortage of skilled labor, and increased use of lower grade ore bodies have all added justification for the use of on-stream analysis. A rise in the number of on-stream units indicates that this type of assay is now being accepted as a necessity. On-stream analysis is a much more rapid means of obtaining true assays of a flowing product when compared to wet chemistry or "grab" samples dried, briquetted and assayed by x-ray. In contrast, on-stream analysis uses real time samples assayed every 30 seconds while each stream is assayed every 5 to 15 minutes. It is very important not only to know that a change has occurred in the process, but to know what caused the change and how to correct for the change. For example, in a tailing sample the elements of interest comprise between 1% and 10% of the sample. The remainder is water and gangue. Previously the gangue was not assayed nor were the low atomic number elements used for corrections. In addition to the demand for higher accuracies some concentrators were being penalized for excessive Ca or in some cases 5i in their concentrates. This penalty was being imposed by the smelter in order that they could better cope with pollution problems and prolong the life of their furnaces. But until Ca, 5i, and S are measured on-line, nothing can be done about their control. By accurately measuring these light elements on-line, a complete assay is obtained of the total sample providing improved accuracy for the important products. The justification for complete accuracy assays is now even more obvious because they are possible at very 1ittle increased cost and at no increase in analytical time.

Jan 1, 1977

By H. Habenicht, E. Urschitz

Three mining methods for full extraction in flat coal seams - i.e., longwall (L W), shortwall (SW), and rib pillar extraction (RPE) - are com- pared with each other in view of the introduction of a mechanized, self-advancing roof support. Features are shown according to which RPE appears most attractive under certain conditions. In this presentation, the mining methods are outlined and discussed. The new support (Alpine Breaker Line Support, ABLS) is described, and its employment is explained. A trial operation in RPE using the ABLS has been conducted successfully in a South African coal mine. The results and improvements are stated.

Jan 1, 1988

By J. D. Miller

"Bastnaesite is one of the important mineral resources for the production of rare earth materials, and it is typically associated with calcite and quartz as gangue minerals. Fatty acid or hydroxamic acid are recommended collectors for bastnaesite flotation. In this research, potassium lauryl phosphate was expected to provide a stronger flotation response for bastnaesite than for the calcite and quartz gangue minerals. Using potassium lauryl phosphate as collector, the results of captive bubble contact angle measurements, zeta potential determinations and microflotation experiments for bastnaesite, calcite and quartz are reported. Greater selectivity for bastnaesite was achieved using potassium lauryl phosphate than using octyl hydroxamate as collector. These results indicate that potassium lauryl phosphate might be a promising collector in the flotation of bastnaesite ores. The computation results of universal force field (UFF) interaction energies for the mineral-reagent interactions are also reported and were found to correlate well with the experimental microflotation results.IntroductionBastnaesite ((Ce,La)FCO3) belongs to the mineral class of semisoluble salt minerals, whose characteristics include ionic bonding and limited solubility in water. Bastnaesite, for the most part, contains the cerium subgroup or the lighter rare earth elements (Zhou et al., 2014). The Mountain Pass deposit in California in the United States and the Bayan Obo deposit in Mongolia in China are the two major deposits of bastnaesite (Azizi et al., 2016; Satur et al., 2016). Calcite and/ or quartz are common gangue minerals in these and many other rare earth deposits (Jordens et al., 2014)"

Jan 1, 2017

By Jr. Gambrell

For more cost effective strata control, a fundamental understanding of the behavior of the support system is needed. To assist in this understanding for shield supports, behavior of a four-leg shield design used on a soft floor in an operating longwall system is presented. The shield was constructed having a split base and a split caving shield. Attention is focused on other-than-normal loading on the canopy and its effect on deformation of the lemniscate links. Examples of the typical bending and twisting deformations are given. Schematics of the canopy, caving shield, and lemniscates showing important forces and moments are presented. Approximate minimum values of the forces and moments are calculated. The need for use of more inclusive three-dimensional design techniques is demonstrated.

Jan 1, 1990

By Daniel B. Brimhall

The research presented here was initiated to investigate the role of atmospheric oxygen in the leaching of copper waste dumps. The problem of increasing the recovery rate of copper from these dumps is or great importance considering there are by conservative estimate in excess of fifteen billion pounds of copper located in dumps in the western United States. At this time, there is an increased interest in recovering copper from these dumps on a large scale. Large tonnages of low-grade material are being placed on the waste dumps of most copper mining operations in the western United States each day. The size of these dumps ranges from 5.5 million tons at Mineral Park, Arizona, to 4 billion tons at Kennecott's Utah operation (1). Leach solutions are recycled and contain ferrous and ferric sulfates. Large quantities of dissolved aluminum, magnesium and calcium salts may also be present. To this solution make up water is added to maintain the solution inventory and sulfuric acid is added for pH adjustment. Iron is introduced into the leach solution by the dissolution of the iron-containing sulfide and oxidized minerals present in the ore deposit. In addition to the iron from dump leaching, iron is also introduced during the precipitation process when the pregnant solution is passed over metallic scrap iron if cementation is used to reduce the copper in solution.

Jan 1, 1972

By S. D. Van Nort

The Grasberg porphyry copper-gold deposit of Freeport Indonesia Inc., an 81% owned subsidiary of Freeport-McMoRan Inc., lies within the Ertsberg Mineral District in central Irian Jaya, Indonesia. The Grasberg deposit was discovered during a drilling campaign initiated in early 1988. Production at the open pit Grasberg deposit commenced in December 1989. The Grasberg copper-gold orebody is contained with a young igneous complex of dioritic composition which intrudes limestones of the Tertiary New Guinea Group. Alteration is typical of porphyry copper deposits worldwide except that higher grade primary chalcopyrite with significant gold values is associated with a centrally located zone of strong quartz stockwork.

Jan 1, 1991

By Chee Theng

"Getting minerals out of ores is messy, but mineral processors learn to have fun with it. Celebrating the innate joys of the industry was the theme of this year’s Colorado MPD Conference. At the same time, attendees dug deeper for insights into problems that continue to dog the community, including tailings dam crises, water resource challenges, and a dwindling number of academics to teach and train the workforce (see box).Tailings dam crisesMatt Fuller of Tierra Group International Ltd. brought some of the audience to tears with his impassioned talk on “The Infamous Legacy of Upstream Tailings Dams,” which won the conference’s Lou Cope award for best paper. The talk was especially poignant coming on the heels of the January tailings dam failure in Vale S.A.’s Córrego do Feijão iron ore mine in Brazil, the latest in a series of catastrophic dam failures over the past decade that includes the Fundão dam failure in 2015.Noting that the two dams share a common characteristic — both are upstream tailing dams — Fuller explained the three basic dam construction methods and why certain upstream tailing dams are susceptible to failure (Fig. 1). The downstream, centerline and upstream methods denote the direction the centerline of the dam crest moves with each successive raise in elevation of the dam. With the downstream dam, the foundation for future raises is essentially the same as that of the starter dam, he explained. With the centerline dam, half of the dam is constructed on the same foundation as the starter dam, and with the upstream dam, each successive raise is built out over the top of the tailings.“Downstream dams are expensive to build because each successive raise is bigger, so the sustaining capex to build them keeps growing,” Fuller said. Many decades ago, mine owners realized they could construct a starter dam, put their tailings through a hydrocyclone, generate a coarse sand fraction and stack the sand over the top of the tailings to build the next raise. “Then, there is no sustaining capex, it all comes out of operations,” Fuller added. The footprint is smaller, and it is a favorable means of retaining the tailings."

Jul 1, 2019

By J. `. Spitzinger

In situ recovery (ISR) of uranium alters the baseline groundwater geochemistry in order to mobilize and complex uranium to extract and concentrate it. ISR wellfield restoration is often challenging, and primarily relies on groundwater sweep, reinjection of treated permeate, and/or injection of reductants. Greater focus should be placed on injection-based approaches (using existing infrastructure) based on established engineering concepts used for in situ remediation of groundwater plumes. Such injection-based approaches could shorten restoration timeframes consequently reducing long-term operational costs. This paper addresses various types of injection-based approaches to wellfield restoration based on in-situ remediation success with other constituents that require similar treatment. This paper describes necessary design practices for injecting reactive chemicals (e.g., reductants or biostimulants), operations and maintenance (O&M) strategies to prevent fouling of the chemical delivery system and well network, and natural constraints to restoration. Best practices for successful biostimulation strategies that minimize residual uranium, radium, oxoanions, and other trace elements are as described. Advantages of such injection-based approaches could include significant reductions in restoration times, and consequently, lower restoration costs.

Feb 23, 2014

By Hemendra N. Kalia

To plan a safe and efficient coal mining operation, the design engineer should use all the available information regarding the property to be exploited. The reliability of the mining operation must be as high as possible so that the plants relying on the coal can operate at the maximum design capacity. A good design should incorporate all of the known geological characteristics of the deposit, the structural and physical properties of the coal, as well as the rock which will form the roof and floor of the mine openings. A systematic method is proposed as a guide to insure a mine design that will be safe, efficient and will minimize surface disturbances resulting from mining operations. It is anticipated that the method proposed will result in maximum extraction at perhaps minimum cost to the operator. In general, to develop a mining area, several factors are systematically reviewed: (1) determination of the economic minability of the deposit, (2) the computation of the coal reserves, (3) the marketability of the coal, and (4) the life of the property. In general, boreholes are drilled in a predetermined pattern and geophysical or geological methods are used to log the boreholes. The information so obtained is primarily used to determine the quality and the extent of the deposit and to determine to some extent such geological features as faults, barren areas, washouts, and channels.

Jan 1, 1973

By T. R. West

Planning for urban development in many locations is based largely on 0.10 factors, 1) soil conditions and 2) socio-political aspects of the region. A more widely based approach is necessary, however, if a complete and functional plan is to be obtained. Under this unified approach, the overall field of earth science is included in the planning process. As considered here, the earth sciences comprise a large segment of the natural sciences; that is, geology, pedology, geomorphology, reengineering geology and ground water hydrology. A number of shortcomings can develop when using the restrictive, two-factor approach for urban development planning. These deficiencies are discussed in the paper. The specific considerations for each earth science area are examined and land use considerations for various urban requirements reviewed in light of these specialties. To illustrate the potential of the unified or earth science approach, Tippecanoe County, Indiana is presented as an example. The current area planning system for Tippecanoe County is examined to determine how well it compares with the unified approach and some of the shortcomings of the current plans are discussed.

Jan 1, 1972

By D. D. Harbuck

The U.S. Bureau of Mines investigated germanium and gallium extraction from an ore containing 0.089% Ge and 0.036% Ga. While previous researchers concluded that a reducing agent such as 502 is needed to extract germanium and gallium from such ore, this research showed that high extractions (87% Ge, 97% Ga) were possible using sulfuric acid alone, if the acid concentration were properly controlled. This control was achieved using a two-stage counter-current leach circuit. Microprobe analyses revealed that the non-extracted germanium is in solid solution with quartz, and therefore cannot be leached with 502 or sulfuric acid.

Jan 1, 1991