Search Documents

By Fabrizio Fara

The Ship Canal Water Quality Project (SCWQP) includes a 2.7-mile long, 18'-10" internal diameter tunnel which is located inWest Seattle. Tunneling in urban areas and soft ground conditions (Till and Till-like soils in Seattle) is associated with the risk of settlements, especially in presence of groundwater above the alignment. The Designer foresaw the use of soil improvement (jet grouting) outside of the launch shaft to mitigate the risk of flowing ground and to provide a redundant sealing. The Contractor proposed and ultimately successfully executed a different approach by using a “Steel Bell System” or Pressurized Can as described in this paper.

Jun 13, 2023

By William J. Miles

For compliance with the Hazard Communication Standard and other federal and state regulations, numerous minerals, chemicals and products need to be evaluated for crystalline silica content at a threshold of 0.1 %. The polymorphs of crystalline silica that can occur in chemical and mineral products are quartz, cristobalite and tridymite. Other natural, industrial and synthetic amorphous silicas and hydrates must be distinguished from these polymorphs to prevent over-regulation in the workplace and environment. A number of industrial silica products are composed of glasses, expanded perlite, diatomite, slags, and precipitated and fumed silica products. Amorphous silica hydrates used for industrial products, include opal (hydrated silica of biogenic or inorganic origin), perlite, pumice and tuffs. In addition, crystalline and amorphous silicate minerals and chemicals, abundant in nature and industrial products, must be distinguished from the polymorphs of crystalline silica.

Jan 1, 1997

By H. K. Lin

During slow-cooling crystallization of iron-making blast furnace slags, most rare-earth elements in the feed recrystallize as cerite-calcium while scandium and europium concentrate in a sheet-like "mineral". The mineralogy of this "mineral" is studied with one of the objectives being the extraction of the "mineral" from the slag for recovery of Sc and Eu. This "mineral" has been identified as one of the mica group minerals and can be named as rare-earth-bearing barium fluorophlogopite. The mineralogical characteristics of this "mineral" are investigated and discussed. This "mineral" can be effectively recovered from the slag by flotation with dodecylammonium acetate or a combination of dodecylammonium acetate and sodium oleate as a collector.

Jan 1, 1996

By Kenneth E. Merklin

The heavy media process is now being used extensively throughout the world for the gravity concentration of a great number of different minerals. The process is a commercial adaptation of the heavy liquid procedure which has been used in laboratories for many years to separate mineral of different specific gravities. In the heavy media process, a suspension of finely divided particles in water is used to increase the apparent specific weight of the fluid to the desired separating point. The original heavy media process used sand, galena, pyrite and occasionally other materials as the solid constituent of the separating suspensions. As the process developed, the need for a more universal media meeting the following requirements was recognized: 1. High specific gravity. 2. Resistance to abrasion. 3. Resistance to corrosion, 4. Readily reduced to a suitable size consist for suspension in water. 5. Available in quantity at economical price levels. 6. Easy to recover by a simple method.

Jan 1, 1958

By P. Eng. Daniel Kelly

INTRODUCTION The Astoria property is located in the prolifically mineralized Abitibi greenstone belt and is one of the most advanced projects presently under development by Yorbeau Resources Inc. This property, which hosts the Astoria gold deposit, is located in the southern part of Rouyn township, Abitibi area, Quebec, 4 km south of the city of Rouyn-Noranda (Figure 1). The Astoria deposit has been the subject of underground development for over a half century, beginning with Granada Rouyn Mining Co. in the 1930's and followed by Astoria Rouyn Mines Ltd. in the 1940's. Yorbeau Resources Inc. acquired the property in 1984 and has, since then, conducted numerous exploration programs on this gold deposit. The diluted reserves of the Astoria deposit are estimated at 1,3 million metric tons grading 6,14 grams of gold per metric ton (1.4 million st at 0.18 oz/st). This reserve figure is based on the results of surface and underground exploration carried out from January 1986 to June 1987 and includes ore in the proven, probable and possible categories. This paper is divided into two sections. The first part includes a summary of the geological environment including a description of the gold bearing zones and a short discussion on wall rock alteration. The second part of this paper reviews the underground work and the objective of the ongoing exploration program.

Jan 1, 1988

By Russell L. Cook

Stringent environmental regulations, which have limited the use of sludge ponds, coupled with the economic incentive to clean more 'coal or to add fine coal cleaning additions to existing preparation plants have increased the use of static thickeners in preparation plants. The Lamella Gravity Settler, sometimes de signated Lamella Thickener, is a shallow depth sedimentation device which has been applied in a variety of industrial process and wastewater control projects in place of the conventional raked thickeners. This paper presents the theory and design of the La-mella Thickener, as well as describing the operating results from several full scale installations in a variety of Appalachian preparation plants.

Jan 1, 1977

By T. W. Martin

In 1973 the percentage of total coal production mined by surface methods in the United States again increased, reflecting a long term trend. Barely three decades ago less than 10 percent of the U.S. coal was produced in this manner. Last year surface coal mines produced 299 million tons, 50.7 percent of our nation's coal. At present there are about 2450 strip mines producing coal in 23 states. While accident rates for surface coal mines are less than underground coal mining rates, surface coal mining is certainly one of the more hazardous occupations. Figure 1 shows the injury rates (fatal and non-fatal accidents) of major U.S. industries. Note that surface coal mining is more hazardous than all other industries except contract construction. Accident rates are about the same as the contract construction industry which uses similar equipment. A limited amount of detailed data was available on elements of surface coal mining jobs and this lack of compiled information made it difficult to assess the significance of the conditions contributing to accidents and to make recommendations that would reduce accident frequency. Therefore as part of the Bureau of Mines continuing research efforts related to the health and safety of the coal miner, a contract was awarded to Theodore Barry and Associates of Los Angeles to conduct an "Industrial Engineering Study of Hazards Associated with Surface Coal Mines."

Jan 1, 1974

By E. Stemn

Incident investigation is of utmost importance in most high-risk industries. This study was undertaken to study the content of past investigation reports to determine the effectiveness of the incident investigations. The study uses a semi-quantitative method to assess the effectiveness of incident investigations in the Ghanaian mining industry by evaluating the quality of past investigation reports. The assessment tool consists of 5 elements with several indicators and rating scales for assessing the quality of an investigation report as a measure of the effectiveness of the investigation. The method was applied to 304 investigation reports of 3 Ghanaian large-scale gold mines, and the results correlated with incidence rates of the mines to determine if any relationship existed. The results showed that the mines differ significantly in the quality of their investigation reports, suggesting differences in the effectiveness of their investigations. In addition, the incidence rates of the mines negatively correlated with some elements of the assessment tool. In general, the method was found useful and revealed areas where improvement is needed. INTRODUCTION The importance of learning from incidents is well documented in the literature. For instance, some scholars regard learning from incidents as important for improving safety [1,2]. Thus, many organisations spend considerable resources in identifying lessons from incidents and subsequently on the process of improvement that follows the identification of lessons. It is therefore important for such organisations to determine the effectiveness of their learning from incidents processes, in order to identify specific areas where improvements are needed, so that interventions can be as specific as possible. The learning from incidents process models the plan-act-check-do approach of management systems, often consisting of four major stages, namely; data collection and incident analysis, planning interventions, implementing interventions and follow-ups and evaluation [3,2]. The investigating and analysis of incidents have been regarded as one of the vital stages of the learning process since it is the stage where lessons are identified [3,2,4]. It has also been noted elsewhere in the literature that results of the previous stage of the learning process are important for the next stage [3]. For example, ineffective incident analyses could result in the planning of ineffective remedial measures. One of the primary aims of incident investigations is to identify lessons from previous incidents which when implemented can prevent future recurrences or minimise the effects of future incidents. There is thus the need for organisations to assess the quality of their investigations periodically since it is one of the means they adopt to improve safety and the quality of remedial measures to some extent depends on the effectiveness of the investigations. Although previous studies [5,2] have assessed the effectiveness of the learning process, and some aspects of the learning process, such as incidents reporting, there is less focus on the effectiveness of incident investigations. The research described in this paper was therefore conducted to contribute to this gap, focusing more closely on incident investigation reports.

Jan 1, 2019

By David A. Lee

It was estimated in Chemical Week1 that the uranium fuel requirements for the U.S. Electric Utility Industry by the mid 1980's would be about four times that-of what it is today. This corresponds to approximately 45,000 tons per year of 'yellow cake' - of which a good portion is represented by ammonium diuranate - vs. the 11,700 ton total estimated for 1975. Perhaps just as significant is the 40-fold increase in thirty years projected for the entire world since 1970. Thus by the year 2000. 'yellow cake' production could be in the order of [3]50.000 short tons annually.2 'Yellow cake', so named because of its inherently bright yellow color, is a finely divided precipitate that can be formed after the leaching step when refining uranium ores. Feed solids enhancement then occurs to at least 50% by weight using filters or centrifuges This is followed normally by drying and then calcining with the conversion of ammonium diuranate to triuranium octoxide represented by the following equation: [9 (NH4)2 U2 07 heat 14 NH3 7 + 15 H2O7 + 2N2/ + 6 U308 4] Theoretically, assuming 100% conversion every 100 kgs. or 100 lbs. of ammonium diuranate will result in 90 kgs. or 90 lbs. of triuranium octoxide.

Jan 1, 1976

By D. H. Desy

This research was undertaken to establish the lncendivity of aluminum alloys against rusty steel under frictional impact conditions at typical coal mine fan speeds, to determine any differences in incendivity among various aluminum alloys, and to Investigate less incendive materials as substitutes for aluminum alloys. With a specially designed apparatus, three aluminum casting alloys and three constructional steels were tested for incendivity in frictional impact against rusted steel in flammable methane-air mixtures. Although varying in degree, all aluminum alloys investigated exhibited a high ignition probability under the test conditions; none of the steel specimens tested caused any ignitions under the same conditions.

Jan 1, 1973

By Michael P. Evans

Traditionally in coal processing jigs have been used to clean the coarse coal fraction, the +3/8" or +1/4" material. Today with the advent of modern fine coal jigs in the United States, its place was moved from the coarse to the inter- mediate coal circuit, the 3/8" x 100 mesh. The most economical coarse coal circuit to build and operate is a heavy media bath circuit. The following table summarizes the cost per raw coal ton processed for a coarse coal jig circuit, and a coarse coal heavy media bath circuit. The flowsheets used to compare these two circuits are shown in Figures 1 and 2.

Jan 1, 1983

By C. H. Cheh

The amount of fines in run-of-mine coal has been increasing and coal quality has been deteriorating as a result of the increased use of mechanized and continuous mining methods. Removing the mineral matter and pyritic sulfur from coal prior to combustion will lower transportation costs, improve power plant performance and reduce sulfur dioxide emissions. Since physical cleaning methods can only remove individual particles of mineral matter and pyrite, it is necessary to crush and grind coal to fine sizes to separate these contaminants so they can be removed by deep cleaning processes. The increased portion of fines in run-of-mine coal together with attempts to increase the mineral matter removal efficiency have stimulated interest in fine coal cleaning technology. However, there are many problems to be solved before fine coal cleaning can be applied to power plant coals. These problems include: 1. coal cleaning plant capacity is reduced when conventional cleaning circuits are modifies to deep clean coals; 2. existing equipment and technology is not suitable for cleaning fine coal; 3. coal recovery is reduced; and 4. fine coal is difficult to dewater, dry, handle, transport and store.

Jan 1, 1982

By J. G. Groppo

Lowering of filter cake moisture of ultra-fine coal to a 20 percent level using conventional vacuum filtration could be achieved using a combination of metal ion and surfactants. Pretreating coal slurry with about 0.2 Kg/ton of a surfactant and 50 ppm of copper or 10 ppm of aluminum ions provided filter cake containing 22.8 percent moisture. The lowering of moisture is explained due to formation of hydrophobic micro-agglomerates which facilitates dewatering.

Jan 1, 1994

By L. E. Sausa

Measuring the specific gravity of a pulp in concentrating plants is a relative, y simple procedure, but the desired accuracy is often difficult to attain. Many plants use the system of weighing a known volume of the pulp on a scale. In many cases, this method is quite accurate, but obtaining a true sample presents quite a problem. This is especially true when the pulp tends to froth, the solids settle rapidly, or the flow is fast at the point of sampling. There is also the problem of the operator neglecting to take the sample because of duties elsewhere, or, if everything Is apparently running smoothly, he assumes the pulp density is also all right. In 1952, the Pine Creek plant of Union Carbide Nuclear Company began working on a better method for measuring and controlling pulp density. After an extensive investigation of different methods for measuring the specific gravity of moving pulps, the Research Department decided that the bubble tube method appeared to be the simplest and most promising for our applications. It consists of two bubble tubes, of different lengths, submersed in a pulp. Low pressure air is supplied to, the two tubes through sight bubblers to maintain approximately equal volume of air to each bubble tube. The bubble tubes are also connected to a differential manometer, one to each side. Therefore, knowing the vertical distance between the outlets of the bubble tubes, the manometere can be calibrated to measure directly the specific gravity of the pulp. (Figure No. 1 illustrates this model.)

Jan 1, 1960

By Weibai Hu

The flotation separation of wolframite from fluorite and quartz is investigated with chelating agents and neutral oil as synergic collectors. Test results indicated that a-nitroso-ß-naphthol has a strong collectivity for wolframite and selectivity against fluorite and quartz. The 8-hydroxyquinoline has collectivity and selectivity also. They both have a better activity than sodium oleate. However, the cupferron is slightly inferior. The synergism of chelating agents and neutral oil looks promising, especially for fine wolframite particles. The activation effect of Fe2+ and Ca2+ ions on separation of wolframite from fluorite and quartz is slight. The UV absorb-spectra measurements showed that the adsorption of chelating agent on wolframite is multilayer, and flotation behavior is related to chemisorption. The chelating agent which bonds to Fe and Mn sits on the wolframite surface, and the reaction between Mn2+ ion with collector is more significant. The essentials affecting reagent activities are the bonding factor and the hydrophobic factor. These factors are discussed by structure-activity relationship theory. The synergism of neutral oil is a secondary collector likely to lengthen the hydrocarbon chain of chelating agents.

Jan 1, 1985

By C. Vasilescu

Phytotechnologies use plants to remediate various media impacted with different types of contaminants. These technologies can be implemented either in situ or ex situ. The affected media in which phytotechnologies can be applied include soil, sediments, groundwater and surface water. They are best applied at sites with shallow contamination of organic, nutrient, or metal pollutants that are amenable to one of five treatment options: phytoextraction, phytotrans-formation, rhizosphere, bioremediation, phyto-stabilization or rhizofiltration. Phytoremediation can be used along or, in some cases, in place of mechanical cleanup methods. Phytoremediation can be used to clean up metals, pesticides, solvents, explosives, crude oil, polycyclic aromatic hydrocarbons and landfill leachates.

Jan 1, 2006

By Botond Beno, Dave Watson, Danny Read

The Hampton Roads Bridge-Tunnel (HRBT) Expansion widens the existing I-64 four-lane bridge-tunnel corridor to eight lanes through construction of two parallel tunnels, interstate widening, and bridge expansions. The design-build contract was awarded to Hampton Roads Connector Partners with HDR and Mott MacDonald retained as lead designers in a Design Joint Venture. This paper will highlight some of the e challenges related to the design of the twin bored tunnels from spaceproong, tunnel enabling wors, segmental lining design and durability considerations.

Jun 23, 2024

By Abhiram Kumar Verma, Soumya Ranjan Mallick

Generally, waste such as soil and sandstone is used in mines for road construction or haul roads. In many such mines, it is challenging to design haul road pavement to match the dumper capacity. This paper investigates overburden soil to find its utility as a pavement material. It is found that overburden soil is unsuitable pavement material without stabilization; hence, nine composite materials are developed using overburden soil and RBI. Physical, mechanical and microstructural properties of unstabilized and stabilized soil are determined. Statistical analysis is carried out to assess the effect of soil type, RBI and curing period of strength characteristics of unstabilized and stabilized soil. ANOVA tests assess the influence of RBI percentage on soil geotechnical properties, and regression relations are developed. Two-way ANOVA shows the effect of RBI and soil type on soil geotechnical properties, whereas one-way ANOVA shows that the influence of soil type is more than the RBI. The regression relation is developed for CBR, UCS, Poisson’s ratio and modulus of elasticity with a good correlation coefficient. The performance of RBI is more with the finer material and reduces with an increase in the size of soil grains. The performance of the developed composite is better than the earlier developed composite based on overburden with fly ash, lime kiln dust, lime or clinker.

Mar 19, 2024

By Todd Minoski, Matthew McElhinney, Mark Morris, Mark Mazzella, Joseph Bright, Morgan Sears, Craig Compton

To promote the safety and health of U.S. mineworkers, researchers with the National Institute for Occupational Safety and Health (NIOSH) are currently involved in gathering additional field data from the nation’s underground coal mines. The purpose of this field study was to monitor ground movement and changes in pressure during mining where conditions include a thick parting in the coal seam. To accomplish this, three arrays of field instrumentation were installed in the wraparound bleeder of a room-and-pillar panel at the Maple Eagle mine located in southern West Virginia. Borehole pressure cells (BPCs) were used to monitor the change in pressure in pillars located adjacent to the gob. Roof extensometers were installed to measure roof sag at various horizons in the immediate roof, while rib extensometers were installed to measure displacement of the in-seam parting as mining progressed. Additionally, visual observations and manual measurements were taken during subsequent site visits. The repeatability of results, important from a scientific perspective, was accomplished by successfully obtaining field measurements from two nearly identical instrumentation sites. The data collected indicated that the front abutment extent at the edge of the panel was approximately 200 ft, corresponding to a distance of 9– 10 times the square root of the depth. Yielding of the slabbed pillar began when the pillar line was approximately 290 ft outby the instrumentation sites. This was followed by load shedding onto the abutments and the measurement of small amounts of roof sag in the No. 1 entry. Instrumentation data, as presented in this paper, can be used to better understand stress redistribution, pillar performance, and roof/rib displacements. Additionally, this data is suitable for assisting in the calibration of numerical models. Insight gained from applying these models can be used to make better engineering-based judgments for conditions that could potentially be encountered in the future.

Jul 1, 2023

By Robert M. Cox

The principal factor that must be determined for the effective design of a coal mine roof bolt support system is the maximum stable tension that can be developed with a given bolt assembly in a particular roof rock. There are four basic types of roof bolt anchorage techniques available: (I) the splitwedge; (2) mechanical expansion units; (3) resin point anchors or grouted expansion units; and (4) the cone shell which is placed in a reamed hole. A study of this problem has been made which includes theoretical analyses, laboratory experiments and field tests. A static free-body analysis of each of the anchorage techniques has provided formulas for predicting the anchorage capacity for a particular rock from the results of standard pull tests. The formulas also provide an insight into the anchorage mechanism of technique and allow for a comparative evaluation of the methods for design purposes. The theoretical analyses also indicate clearly the pertinent variables affecting the anchorage mechanism of each method.

Jan 1, 1977