Search Documents

By E. B. Thorn

The production of portland cement requires that four basic elements -- calcium, silica, alumina and iron -- be ground to a fine powder, homogenized, and fed to the pyroprocessing unit, where it is burned to a cement clinker. The raw material must either be ground wet in a slurry form or dried and ground to a dry powder, with a fineness of approximately 85% passing the 200 M screen. According to the Portland Association's Plant Information Summary, approximately 38% of the U.S. capacity is ground wet and 62% ground dry. The following data is taken from the Portland Cement Association's 1981 Energy Survey: [Million BTU/Ton kW h/Ton Wet Process Plants 5.86 138 Long Dry Process Plants 4.97 123 Dry Preheater Plants 4.03 157 ]

Jan 1, 1984

By Peter Werner

Technological advances in mine equipment and milling processes have enabled mining companies to exploit ever lower grades of ore. The result has been larger disturbances, greater volumes of waste, a complex web of infrastructure, and an overall trend towards mega-projects that can extend over several square kilometers. This explosive growth in a mining operation’s disturbance footprint provokes an obvious question: What’s it going to cost to reclaim all of this? At face value, this can be an enormous financial liability for a company, but since the timing of reclamation may be years in the future for many operations, these costs can be heavily discounted thereby limiting the burden on the corporate balance sheet. Nonetheless, mining companies are eager to remove these liabilities as quickly as possible, conversely, regulators want assurance reclamation will, in fact, occur. How might one bridge these competing interests? Navigating the practical and financial requirements of a post-closure landscape requires foresight, judgement and assumptions, however, companies who do not adequately plan for these future expenditures when there is no off-setting income stream will likely face some difficult decisions. Simple risk analysis tools and utilizing the time value of money can help bring some clarity to this end-of-mine life phase.

Feb 1, 2025

By G. Thorsen

An alternative way to the normal practice of precipitation of jarosite, goethite, or hematite for removal of iron from zinc sulphate process liquors/ is to employ the techniques of solvent extraction. The process presented avoids the addition of any external alkali for the extraction of iron by integrating the leaching and solvent extraction steps in a hydrometallurgical zinc plant. By starting the leaching of zinc from the solid zinc calcine material with an organic solution of an acid liquid cation exchanger, the organic phase is loaded with the organic zinc salt from the direct reaction with zinc oxide. The residue from the organic leaching is transferred to a hot acid leach circuit where the remaining zinc oxide and the zinc ferrites will dissolve form¬ing an aqueous sulphate solution of zinc and iron. In the subsequent solvent extraction of iron from this aqueous leach solution, iron is exchanged with zinc from the organic phase. The commercial carboxylic acid Versatic 10 (Shell) is highly efficient for this integrated process of leaching and solvent extraction. The resulting iron-loaded organic phase is heated to 150-200 C in the presence of water whereby the iron will be directly precipitated from the organic phase as iron oxide of high purity and the regenerated organic acid is recycled to the organic leaching step for reloading with zinc.

Jan 1, 1980

By R. Scheffel, R. Washnock, G. Zarate

"The second survey of global copper leaching operations has been completed, the data published in 1998 has been updated. A survey questionnaire was sent to 40 identified copper leach operations around the world including those leach properties still in operation that responded to the 1998 survey. This paper lists the results of 26 operations that responded to the survey. Selected information from the survey is represented in graphical form. INTRODUCTION Copper leaching was first performed by truck dumping huge monolithic stockpiles of ore and flooding the surface with leach solution or lixiviant with little understanding to the parameters that support optimum recovery of the metal. Heap leaching has evolved into a controlled process whereby a complex low grade ore is stacked in shallow lifts (under 10 m in most cases). The ore is usually crushed and agglomerated, conveyor stacked on an engineered containment system (leach pad) and irrigated in a controlled manner. The lixiviant chemistry is designed to extract the optimum amount of metal from the ore. At first glance, heap leaching appears to be simple in nature. In fact, it is a very complex process. A plethora of technologies such as material handling, environmental control, analytical techniques, solution chemistry, hydrology and many others contribute to the design and operation of a heap leach. Heap leaching requires an inter-disciplinary approach between geologists, mining engineers and metallurgists. Many operational factors affect heap leaching. The process must address climatic factors, flexible operation, quality control before and after leaching, physical characteristics of the ore, geology, mineralogy, reagent consumption, solution application rate and methods (wobblers or emitters), particle size, and favorable conditions for bacterial growth and survival. Predicting, troubleshooting, and optimization of leach recovery is a significant challenge when considering the number of variables involved and their interactions The survey updates many of these key operating parameters to the current state of the art. It should provide the reader an excellent benchmarking summary of these factors on a site-by-site basis."

Jan 1, 2016

By G. Brofas

The reforestation potential of bauxite mining spoils by seeding was examined on this research work. The experimental plot was established on the location Strofi Koukouvista 5, Ghiona Mountain. The experiment consists of 3 species (Pinus nigra, Robinia pseudoacacia, and Spartium junceum) with 4 sowing treatments and 2 sowing seasons (autumn and spring). The treatments were: (1) broadcasting; (2) broadcasting and soil cultivation; (3) broadcasting with straw mulching and straw binding with asphalt emulsion; (4) broadcasting with soil cultivation, straw mulching and straw binding with asphalt emulsion. Third year results show that spring is better than autumn as a sowing season. Only the Spartium junceum species were found to germinate and survive in autumn. The results are better for all the species on the spring seeding. The most effective treatments for Robinia pseudoacacia and Pinus nigra are 3 and 4 while for the Spartium junceum even simple broadcasting shows good results although the best ones are achieved with treatments 2, 3 and 4. The paper?s findings show that reforestation by sowing could be effective for some species but further experimentation with other species is recommended. Concerning Robinia pseudoacacia, testing of different seed preparation treatments is needed in order to maximize the germination of seeds.

Jan 1, 2002

By Wesley W. Eckles

Microcomputer technology has begun to revolutionize petroleum engineering. Petroleum engineers' use of relatively inexpensive personal computers (PC's) is likely to continue expanding rapidly. Since 1982 SPE's Microcomputer Applications Committee has developed a Society-wide users group, a bi-monthly newsletter (MICROCOMP NEWS), an SPE Short Course, a hardware and software distribution program, and a world wide electronic network (SPE NET). The purpose of this paper is to share SPE's experience in creating a dynamic program for meeting the individual member's need in the application of microcomputers to petroleum engineering. My hope is that this will encourage other engineering and scientific organizations to provide similar programs for their members.

Jan 1, 1985

By M. Adnan Goksel

The hydrothermal agglomerating process described (U.S. Pat. 3,235,371, (1966)) is different from the conventional high temperature processes. Green pellets or briquettes made with mixtures of moist iron ore concentrates and burned or hydrated lime fines are hardened in an autoclave at 198°C and under steam pressure for 1/2 to 5 hours, with or without previous drying. Under the neutral conditions, oxidation of magnetite does not occur as in the conventional processes. The resulting agglomerates are hard and resistant to abrasion and weathering, and they do not disintegrate in the Linder test. The equipment required for the process is not complicated, and favorable operating costs are projected because of the low temperature and efficient heat recuperation. A low capital investment makes the process attractive even when the annual pellet production is below a million tons.

Jan 1, 1968

By J. B. Offei, K. Awuah-Offei

Mining companies registered with the SEC were required to comply with Regulation S-K 1300 for their annual report covering the first fiscal year ending on or after January 1, 2021. Consequently, most mining registrants filed their first S-K 1300 compliant disclosures in 2022. The US Securities & Exchange Commission (SEC), as part of its disclosure review program, has been issuing comment letters in response to these filings. This paper presents an overview of the trends in these comment letters. The authors reviewed comment letters retrieved from the SEC’s EDGAR database based on Standard Industrial Classification (SIC) Codes that cover mining, the content of the comment letter (whether it references S-K 1300 or not), the names of SEC staff listed in the comment letters, and other criteria. The analysis shows the SEC staff's reviews have been comprehensive covering the breadth of S-K 1300 and eliciting compliance with the rule. The staff through their comments are eliciting all the disclosures required by S-K 1300 and are not allowing registrants to substitute disclosures based on other standards for S-K 1300 disclosures. It is important, however, not to over generalize as the comments are based on the particular context.

Feb 1, 2023

By Gary E. Slagel

The federal Office of Surface Mining (OSW) has undertaken an effort to revise many of their permanent program regulations. Numerous procedures for compliance are being rewritten to allow for greater flexibility while meeting the requirements of the Surface Mining Control and Reclamation Act. This study investigates, for certain select provisions, the cost differential between complying with the original OSM standards and the more flexible, state-specific standards being allowed in many of the revised regulations. Estimated cost savings that could be realized under a few of the revised regulations are substantial and should provide a basis for seeking revisions to the state regulatory programs.

Jan 1, 1982

By Levent Ozdemir, Gerald Dollinger

An extensive series of linear and rotary cutting tests were run in soft and medium strength rocks at the Earth Mechanics Institute of the Colorado School of Mines to investigate the possibility of very high speed mechanical excavation for tunnel, raise, and shaft boring. The results of these tests demonstrate that cutter penetrations of 38.1 mm (1.5 inch) and cut spacings up to 228.6 mm (9 inch) are possible in such rock without exceeding the bearing capabilities of the cutters. It was also demonstrated in vertical boring tests that continuous excavation rates up to 38.1 m/hr (125 ft/hr) can be achieved with state-of-the-art technology provided sufficient thrust and torque is available. A predictor model for soft rocks was also developed using the test data. Analysis of this model shows that the errors between the predicted and observed cutter normal loads appear to be independent of cutter diameter, tip width, cut spacing, and depth of penetration. This suggests that the structure of the model is correct with respect to these variables. An analysis of the coefficients in the model was also made and a correlation found between the principal coefficient and Unconfined Compressive Strength. The second coefficient in the model was found to be similar in magnitude to rock properties such as Brazilian Tensile Strength, Shear Strength and Point Load Index.

Jan 1, 1989

By Robert Stefanko

The results of a recent study on the influence of continuous and conventional mining techniques on the size consist and wash- ability characteristics of coal are presented. Eight samples, four each from continuous and conventional mining sections were collected. Each sample was screened in seven size fractions, and each size fraction was totally fractionated at five gravities. The data thus collected was statistically examined for the influence significance of mining techniques, size, and gravity on the quality of the mined product. The paper presents the sample collection method, data gathering and analysis procedures, and major conclusions. The study revealed that there are pronounced differences in the products from the two mining systems and that conventional mining yielded a better product in terms of size-consist, and yield, ash, and sulfur in both the raw and washed products. The results of the study are significant in regard to consideration of resource utilization and conservation, and environmental impacts.

Jan 1, 1974

By Miroslaw M. Hajdasinski

A project's rate of return (ROR) [The list of all the acronyms used in his text is provided at its end.], be it an internal or external one, usually needs to be approximated. The success and efficiency of an approximation procedure depend on the quality of the initiating parameters such as bounds or seed values (guesses). Current approximation procedures commonly use bounds and guesses dictated by intuition rather then by mathematical consideration. The paper presents three ROR-bounding and six ROR-guessing approaches and examines their suitability on the examples of the typical project cash flow patterns.

Jan 1, 1996

By Daniel E. Walsh

A pilot scale study was performed to evaluate the potential for gravity concentration of gold from -13 mm (-1/2"), crushed ore from Ester Dome, Alaska. 9.04 tonnes (9.94 tons) of crushed ore were sampled and processed through a Pan-American jig -Wifley table pilot plant. Plant products were sampled for assay and material balance calculations. Gold recovery through one stage of jigging and two stages of tabling was 17.4% at a concentration ratio of 615:1. Concentrate grade was 766.3 g/tonne (22.4 oz/ton). The feed grade to the plant was calculated at 1.71 g/tonne (0.050z/ton). Jig tailings, primary table tailings and secondary table tailings grades were 1.44 g/tonne (0.042), 1.30 g/tonne (0.038), and 5.47 g/tonne (0.16 oz/ton) respectively. Significant, coarse, free milling gold values were shown to remain in the jig tailings. Concentrate mineralogy is discussed.

Jan 1, 1991

By I. H. Douglas

All grade control methods in use currently by the mining industry are imprecise. The methods suffer from being locally inaccurate, leading to are loss and contact dilution. An ore/waste indicator variable can be used to predict the probability of ore occurrence at a given location, Po. Then, an ore grade Zo for an ore location and a waste grade Zw for a waste location are obtained. The expected revenue is calculated at each location, based on its probability of being are or waste, the corresponding grade, and on the cost of mining and processing the ore or the waste. Finally, the decision of whether to recover the block is based on the expected revenue value for that block. The method is illustrated with an example taken from the Jerritt Canyon district in northeastern Nevada.

Jan 1, 1994

By J. Gibson

"INTRODUCTION As one of the most pressing and important political debates of this century, climate change has captured global attention and is forcing governments to take action towards decreasing GHG and carbon emission levels below what was previously thought to be necessary. With the ever-increasing price of diesel fuel accompanied by the popular topic of carbon taxes and greenhouse gas emissions, the mining industry is looking to industry specialists for assistance. The benefits of a no-idle policy reach far beyond carbon reduction and fuel savings, ranging from decreased maintenance to increased engine life. With products like battery powered A/C systems and diesel-fired heaters, going no-idle is easier today than ever before. With both systems being manufactured to withstand the harsh environments of the mining industry, the end user will see a seamless change from conventional, inefficient belt-driven systems to future, stand-alone mobile equipment HVAC. THE HISTORY OF GHGS AND CLIMATE CHANGE In 1896 Svante Arrhenius first claimed that the combustion of fossil fuels may eventually result in enhanced global warming, but not until 1955 did Gilbert Plass draw global attention to global warming by summarizing that adding carbon dioxide to the atmosphere would intercept infrared radiation and thus warm the earth. Then in the early 1960’s Charles Keeling developed modern technology to produce concentration curves for atmospheric CO2 (Figure 1). In 1988 the Intergovernmental Panel on Climate Change (IPCC) was founded by the United Nations after acknowledgement of a rising global annual temperature. The IPCC consists of over 2500 scientific and technical experts from more than 60 countries, and because climate change could not be solved by a single country, the Kyoto Protocol was negotiated in 1998 requiring all participating countries to reduce their GHG emissions by at least 5% from the 1990 levels. The Protocol was signed by 186 countries in 2001 (since then several countries have retreated from the agreement, including the United States)."

Jan 1, 2015

By Evan Brinkerhoff, Steve Chorley

The largest hard rock TBM ever to bore in the USA, an 11.6 m diameter Robbins Main Beam TBM, recently underwent a planned in-tunnel diameter change to a more compact 9.9 meters. The first-of-itskind conversion process for the Main Beam TBM was undertaken 2.8 km into the bore and was not done inside a shaft or pre-excavated portal. This paper will detail the unique dual-diameter machine designed for the Mill Creek Drainage Relief Tunnel in Dallas, Texas, USA, machine performance, and successful size conversion process that took place in early 2021—a process that utilized the four C’s of construction to enormous benefit: Communication, Cooperation, Collaboration and Coordination.

Dec 1, 2022

By Ihsan Berk Tulu, Deniz Tuncay, DYKE MARK ALEXANDER VAN, Ted M. Klemetti

Bleeder entries are critically important to longwall mining for the moving of supplies and miners as well as the dilution of mine air contaminants and must stay open for many years. In this study, standing supports in moderate cover bleeder entries were observed, numerically modeled and instrumented by researchers at the U.S. National Institute for Occupational Safety and Health (NIOSH). The measurements of the installed borehole pressure cells (BPCs), standing support load cells and convergence meters, and roof extensometers are presented in addition to the numerical modeling results and visual observations made by the NIOSH researchers in the bleeder entries. The results include the effects of multiple panels being extracted in close proximity to the instrumented site as well as over one and a half years of aging. As expected, standing supports closer to the longwall gob showed the greatest load and convergence. The roof sag appeared generally independent of the proximity to the longwall gob. The BPC readings were driven by both the proximity to the gob and the depth into the pillar. The results of this study demonstrated that the entry roof can respond independently of the pillar and standing support loading. In addition, the rear abutment stress experienced by this bleeder entry design was minimal. The closer the mine development, pillar or supports are to the gob, the greater the applied load due to rear abutment stress.

By Jay P. Chapman

The basic control requirement for multi-pump, long distance slurry pipelines are discussed and a particular example of an operating slurry pipeline using programmable controllers is presented.

Jan 1, 1983

By Dennis A. Fenton

This paper presents some techniques and data required to design large ball mills. The advent of larger size mills leads to consideration of the gearless drive as a practical solution to utilize large horsepowwers. The particular shell structure under consideration is subjected to thermal as well as magnetic loads. The magnitude of the inertia, magnetic and shell temperature characteristics have a very significant effect on the design and performance of the hydrodynamic pivoted shoe bearing. Particularly since these bearings have lower frictional resistance properties than hydrostatic trunnion tee rings. The structure of the mill is designed for long life. Parameters involved with the fatigue life of the structure are discussed together with some of the more important aspects of the design.

Jan 1, 1975

By Xiaochao Shu, Kun Wang, Fanwei Meng, Rui Tao

Rapidly searching for carbonatite-related rare earth element (REE) mineralized systems is of paramount importance to explorers, because these systems provide the world’s most significant supply of REE. Biotite and barite are suitable indicator minerals that can offer reliable elemental geochemical information used for REE exploration. In this study, we provided an elemental geochemical dataset of biotite and barite from Cenozoic REE deposits in the eastern Tibetan Plateau, and compared the obtained data to those of biotite and barite forming in other geological settings. The F (i.e., fluorine) contents in carbonatite-hosted biotites are highly variable, with biotites from mineralized carbonatite complexes having much higher values (1.05–2.37 apfu, where apfu = atoms per formula unit) than their counterparts from barren carbonatite complexes (≤ 1 apfu). It is therefore believed that the presence of high-F biotites can be regarded as a sign for predicting REE reservoirs. Barites in REE mineralized systems contain much higher (even one or to orders of magnitude) total REE contents (ΣREE >100 μg/g) relative to those species forming in carbonate-hosted fluorite-barite deposits and open marine environments. This means that the high ΣREE concentration of barite can serve as an effective index for REE exploration. The above information is integrated into a REE exploration program in which the areas with strong local tectonism along cratonic edges are priority exploration targets, and high-F biotites and REE-rich barites can serve as direct indices for rapidly identifying carbonatiterelated REE mineralized systems at a strategic distance from other geological settings.

Jun 9, 2023