Search Documents

By T. J. DeMull

AMAX's Sleeper Mine uses conventional cyanidation milling and heap leaching techniques to produce gold. Since milling operations commenced in March 1986, average ore processing rates have improved from the design rate of 455 tonnes per day to more than 720 tonnes per day. Heap leaching was added to the process facilities in September 1986 at a design rate of 1,500 tonnes per day, and current heap leaching rates exceed 2,680 tonnes per day. Presented are descriptions of the Sleeper processing facilities with emphasis on the crushing and grinding circuits, a review of the selection of crushing and grinding equipment, and a summary of operating performance during the first 16 months of operations.

Jan 1, 1988

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

The effectiveness of the grouting of saturated, fractured rock in the vicinity of underground workings depends to a great extent on the correct interpretation of the specific hydrogeological conditions at the site. During the planning of grouting operations, calculations of the hydrogeologic co-efficients and of the parameters of the isolating grout curtain(s) and the procedures for forming the curtain(s) must be based on valid hydrogeologic characteristics of the fracture system of the rock within each hydrostratigraphic unit (Anon., 1976). This chapter presents a discussion of the background information that must be collected for these purposes. Details of testing are presented in Chapter 3. The general design of new or the reconstruction of existing underground workings requires a broadly based organization having the expertise to develop a grouting operations plan once it acquires the necessary information. The needed information includes: 1) general information about the hydrogeologic section, 2) the engineering design of the underground workings, 3) the geology of the region, 4) the hydrochemistry of the ground water, 5) the hydraulic properties of the rock, 6) the characterization of all gases present, and 7) characterization of the rock's physical-mechanical properties which is necessary to avoid or control hydrofracturing . The geological documentation portion of the hydrogeological investigation is prepared based on the results of geologic mapping, geophysical surveys and on geo-exploratory operations at a regional and local scale. Geological data from the excavation of other underground workings in adjacent areas of the region is also included. Finally the results of site specific investigations in boreholes constructed at the site of the proposed underground activity are incorporated. A section of the preliminary report entitled "General Information about the Project Site" patterned after the parent STG guidance document on this subject must be com- piled based on the contents of geological reports and on the general construction plan for a new project or the plan for reconstruction of an existing operation. This section of the preliminary report must contain concise information about the conditions under which the planned grouting operations are to be conducted. The information must cover the geo- graphic, administrative, and economic subject areas also. Information about sources of electrical power, heat and water supplies, the presence and characteristics of local construction materials suitable for making grout (particularly clay and cement for the clay-based grout), transportation, and the status of communication lines and other services must be included in this section. Map scales for this section should be on the order of 1:25,000. The technical characterization of planned underground workings is presented in a project report chapter called "General Construction Plan for a New or the Restoration of an Old Operation. " The characterization comprises concise information about the purpose of the workings, the planned depths (for shafts) and the length (for horizontal and inclined workings), the inside and excavated diameters (for shafts), the cross-sectional area (for inclined and horizontal workings), and the face and mouth markers. If excavated underground workings exist in the region, then a concise description of them must be provided. The characterization of all excavations and all operational conditions must be specified. The location within the general structure of the proposed operation is specified. Flow charts must be included in this section that show: 1) the plan for opening the deposit, 2) the plans of the mining operations, and 3) the planned geological sections as they relate to the main workings. These graphical flow charts and appendices are drawn in scales of 1:2000 or 1:5000. 2.1 GEOLOGICAL CHARACTERIZATION The geological characterization of a site of proposed underground workings includes the following principal subject areas: stratigraphy, lithology, structural geology and a characterization of the status of fracturing. 2.1.1 STRATIGRAPHY AND LITHOLOGY A description of the geological section of the rocks to be intersected by the planned underground workings is complied on the basis of: 1) research data derived from core extracted from exploratory boreholes and monitoring boreholes, 2) the documentation and mapping of all natural out- crops in the region, 3) the data from all existing under-ground workings in the regions where operations are being canied out already, along with data from adjacent regions, 4) the data from surface and borehole geophysical investigations (standard and specially developed logging methods, and 5) regional stratigraphy. The geological description of the rock must express the maximum detail possible. The description provides the name of the rock, the granulometric composition (for fragmented rock), the composition and type of stratification, the drilling characteristics of the rock, a visual estimate of porosity and density for each stratum identified, the karstic

Jan 1, 1993

By Jr. Koch

In the Hydrogeochemical and Stream Sediment Reconnaissance (HSSR) phase of its National Uranium Resource Evaluation (NURE) pro¬gram, the U.S. Department of Energy (DOE) samples about 1400 sites for stream sediments in each two-degree quadrangle of the National Topographic Nap Series (NTMS) and about 1200 sites for ground or stream water. Through a geological/statistical analysis, we find that NURE data are useful for assessing the uranium resources of the NTMS quadrangles. Our computer-implemented System for Uranium Resource Evaluation (SURE) calculates a score for each NTMS quadrangle based on the HSSR, geologic, and radiometric data; we score the four Colorado quadrangles--Pueblo, Montrose, Durango, and Trinidad--that comprise the study area. We interpret the scores in terms of geology and the known occurrences, which include the Hanson ore deposit with reserves of 30,000,000 lbs. U308 and the Pitch mine with reserves of 1,740,000 lbs. SURE depends in part on distinguishing mineralized or metalliferous granitoids from barren ones through "geochemical signatures."

Jan 1, 1980

By Douglas W. Fuerstenau, Pradip Pradip

The design and development of selective flotation collectors has been the key to the remarkable success of flotation in beneficiating complex, difficult-to-process ores. It remains a challenging area of contemporary research in mineral processing.

By A. Perry

Latin America is in the path of economic growth characterized by increased privatization, joint-venture projects, and reduced trade barriers. Privatization is changing the industrial operating mode from Government-owned/Government-operated to a privately-owned/government-regulated regime. The establishment of joint ventures, such as in construction and management of infrastructure, energy and mining projects, and deregulated industries (electricity/gas/ telecommunications), is now a common practice in the region. These changes, coupled with the growing awareness of environmental protection issues, have led to a sincere effort on the part of the countries of Latin America to establish reasonable environmental regulations and controls (RERCs) for all industries, including mining and energy, for the benefit of present and future generations. However, RERCs require further consideration of many factors with respect to environmental, geologic, economic, and social impacts in the region. The process must find a balance between the need to sustain profitable operations and the need to adequately protect the environment. While striving to find a balance between continued industrial profitability and environmental protection, the RERCs must be scientifically sound, pragmatic, flexible, and enforceable. There has been worldwide attention focused on the environment, and international symposia have been held on such issues as global warming, water pollution, air pollution, and hazardous wastes. Organizations such as the United Nations (UN) and the Organization of American States have performed rather extensive studies on the environment for various industries and activities, and have developed some broad general plans to address environmental concerns. This technical information is available for the asking, and should be considered a starting point for countries embarking on the passage and enforcement of their own RERCs.

Jan 1, 1998

By Wayne S. Cavender

The geochemical association of arsenic and gold in epithermal precious metal deposits of the Basin and Range province is well documented, and in this paper I wish to discuss the evaluation and utilization of this element association for geochemical gold exploration. In 1961-62, I conducted an exploration program on lands controlled by Getchell Mine, Inc, and centered about the Getchell gold mine itself, Besides exploring for new gold deposits, the program was to evaluate these lands for potential deposits of any type; thus, a multi-phase program encompassing a number of exploration methods was conducted. I shall not elaborate on the process of designing the program or of integrating the various methods, but for gold exploration, geochemical methods were determined to have the best potential. This paper is based on that effort. Figure 1 shows the exploration area, which covers the northern half of the Osgood Mountains in eastern Humboldt County, Nevada. The Getchell $line is on the east flank of the range and is about 40 miles northeast of Winnemucca.

Jan 1, 1964

By D. R. Willmer, E. J. Haas

As national and international health and safety management system (HSMS) standards are voluntarily accepted or regulated into practice, organizations are making an effort to modify and integrate strategic elements of a connected management system into their daily risk management practices. In high-risk industries such as mining, that effort takes on added importance. The mining industry has long recognized the importance of a more integrated approach to recognizing and responding to sitespecific risks, encouraging the adoption of a risk-based management framework. Recently, the U.S. National Mining Association led the development of an industry-specific HSMS built on the strategic frameworks of ANSI: Z10, OHSAS 18001, The American Chemistry Council’s Responsible Care, and ILO-OSH 2001. All of these standards provide strategic guidance and focus on how to incorporate a plan-do-check-act cycle into the identification, management and evaluation of worksite risks. This paper details an exploratory study into whether practices associated with executing a risk-based management framework are visible through the actions of an organization’s site-level management of health and safety risks. The results of this study show ways that site-level leaders manage day-to-day risk at their operations that can be characterized according to practices associated with a risk-based management framework. Having tangible operational examples of day-to-day risk management can serve as a starting point for evaluating field-level risk assessment efforts and their alignment to overall company efforts at effective risk mitigation through a HSMS or other processes.

Jan 1, 2016

By J. A. Organiscak

Enclosed cab filtration systems are typically used on mobile mining equipment to reduce miners? exposure to airborne dusts and diesel particulates generated during mining operations. Various filter configurations can be used within the heating, ventilation, and air conditioning (HVAC) systems of cabs to remove the airborne contaminants. The air cleaning performance of cab filtration systems is highly dependent on the efficiency of the air filters, the number of filters used, and their placement within the HVAC system. This paper shows how to mathematically model cab filtration systems and illustrates a methodology for developing other cab filtration system design models. Node diagrams of several filtration system circuits are illustrated with their mathematical models at steady state airflow and concentration conditions. Laboratory and field data are presented to demonstrate the validity and utility of modeling enclosed cab air cleaning performance. The paper concludes that incorporating multiple filters throughout the HVAC system improves the air cleaning performance and robustness of the cab filtration system design.

Feb 23, 2014

By K. E. Burgher

Since World War II, the need for the use of explosives in construction, mining, and quarrying near congested urban areas has increased dramatically. Often times a coal mine, once isolated from a city, finds itself surrounded by residential and commercial structures. The United States Bureau of Mines and others have researched blast design to a point where ground vibration and airblast damage can be avoided. A problem still exists, however. It is the fact that people often react to only the loud noise associated with a blast although it may not cause damage. Most often it is the concussion of a blast, less than 20 hertz and inaudible, that produces damage. Public fear from the "startle" and "fright" of loud blast noise greater than 20 hertz leads to the complaints which are generally unfounded. See Thackray, Touchstone, and Baily (1975) for a further discussion of the startle effects of loud sudden noises. When blasts are designed in accordance with U.S.B.M. specifications, management generally has little to worry about with respect to damage claims. Complaints, however, still arise when the noise is accentuated from the blast. It is meteorological conditions which dictate how the sound levels will propagate. Some mines use small pilot test shots (generally one-two lbs) to determine when atmospheric conditions favor sound travel.

Jan 1, 1987

By M. J. Ross, D. A. Norrgran, J. A. Wernham, J. N. Orlich

INTRODUCTION Laboratory testing for magnetic concentration circuit design is a requirement, just as it is for most other types of concentration. Natural variations in raw materials allow on1 y the broadest of generalities to be made regarding magnetic separation. Further, magnetic fields are geometry dependent, leaving fundamental models of a separator overly dependent upon the exact conditions for which the models were derived. Despite this, an understanding of the basics of magnetic separation and of the problem to be attacked can result in rapid progress towards the final circuit design with a relatively simple testing program. Magnetic Separation Basic Principles A magnetic field can readily be understood in terms of lines of flux. A familiar demonstration of these lines of flux is the pattern of iron filings on a sheet of paper when a magnet is placed underneath. Lines of flux2 are measured in Gauss (1 line/cm2) or Tesla (10000 gauss). Regions of high field strength have a greater number of lines. Field direction is indicated by a convergence of lines. When a particle is placed in a magnetic field it cuts the lines of flux and alters them in one of three basic patterns. These patterns are referred to as diamagnetic, paramagnetic and ferromagnetic. Diamagnetic materials have electronic structures which react to oppose an applied magnetic field. This opposition acts to locally reduce the applied field slightly. The visualization is that lines of flux diverge and go around the particle. Because of this divergence or opposition, a diamagnetic particle will tend to move towards regions of lower flux density. That is to say that the particle will be repelled by a magnetic field. Aluminum oxide and napthalene are examples of diamagnetic materials. Paramagnetic materials have an electronic structure which increases an applied magnetic field. Although these materials also exhibit diamagnetism, they have randomly oriented impaired electrons which align with the magnetic field. The resultant local field enhancement is significantly larger than the diamagnetic opposition. The visual-

Jan 1, 1986

By C. A. Rowland

When studying the feasibility of using autogenous or semi-autogenous grinding, operating and engineering companies frequently request assistance from the mill manufacturers in three areas - 1. Recommendations for studying the suitability of autogenous or semi-autogenous grinding for the specific ore. 2. Mill sizing, to accomplish required grind. 3. Recommendations on mill design and operation. Rod mills and ball mills are selected by the use of bench scale standard grindability tests and established calculation procedures, of which the most frequently used are the Bond Grindability tests and the Bond Work Index equation(1). The accuracy of these have been reviewed by C. A. Rowland in his papers, showing the correlation of work indices calculated from plant operating data and laboratory grindability tests(2)(3). The selection of autogenous and semi-autogenous primary mills has not reached the stage where mill size selection can be made from bench scale tests. Considerably more extensive testing will be necessary than required for selecting rod mills and ball mills.

Jan 1, 1974

By G. E. Rouse

Anomalies of sulfur dioxide and other gases have been defined, by direct measurement, around various sulfide bodies. These readings were made (1) in soil gas and (2) in the atmosphere, from both ground vehicles and, to a limited extent, from helicopters. Test areas included porphyry copper and molybdenum deposits, sulfide bearing vein systems, pyrite zones associated with sandstone uranium accumulations, and pyrite-bearing mine dumps. Some of the deposits are covered by as much as several hundred feet of overburden or barren rock, while others outcrop, or have been exposed by mining operations. Depending on local conditions, background values of sulfur dioxide in soil gas and the atmosphere range from 1 to 15 parts per billion. Using present techniques, anomalous readings are recognized at approximately two times background. Apparent "depth penetration? on known deposits has ranged to several hundred feet. Readings have been made over known deposits from a helicopter and ground vehicle moving at up to 40 mph. The rate at which the survey may be carried out depends largely on the size and extent of the anomaly. The existence and magnitude of sulfur dioxide anomalies around sulfide-bearing deposits is a function of geology, target size, soil moisture, and climatic conditions such as temperature and temperature changes, barometric pressure, wind velocity, and precipitation. Industrial S02 pollution can effectively mask the presence of the anomalies sought.

Jan 1, 1971

By Adam Bedell, Brad Crenshaw

Tunnel project contract documents often present groundwater infiltration requirements for components of the underground portions of the project. All too often these documents require quantifiable target inflows for these components, but only refer to them in subjective terms such as “dry,” “manageable,” etc. The Contractor’s definition of these terms will inevitably differ from the Engineer’s definition of these terms. The purpose of this paper is to look at common subjective terms used in documents and provide suggestions for reasonable quantifiable language. Additionally, the paper will provide information and recommendations on relative levels of cost and effort increase needed to provide increasing levels of water cutoff (i.e., achieve “dryness”?).

Dec 1, 2022

What is your personal view and assessment of the overall health of the industry in the current global economy? The economic outlook remains soft for the near future and, although the global economy is showing signs of recovery, uncertainty has tempered the pace of recovery. In addition to uncertainty, we are still facing significant economic challenges in many parts of the world, including Europe and the United States. The rapid expansion of China?s economy has recently slowed, further contributing to the sense of uncertainty in the overall health of the global economy. This situation is both a blessing and a curse, depending on which sector of the mining industry we are considering. For example, coal, industrial minerals, aggregates, base metal and precious metals markets are impacted by different forces and drivers and will experience different outcomes within the same economic environment. Let me give a few concrete examples to illustrate this concept. The prevailing economic uncertainty that I have just described tends to drive investors toward safe havens. Gold has historically been viewed as a safe haven and as long as investors shy away from traditional investments, gold prices will remain high and gold mining companies will continue to expand and invest capital in their operations. The same sluggish economy that drives gold prices higher has the opposite effect on other segments of the minerals industry. A great example of this is industrial minerals and aggregates used in construction. The markets that consume these minerals have contracted significantly over the past five years. The outlook for this segment is poor, as the glut of available housing continues to inhibit demand for new construction and, thus, many industrial minerals. In addition to this, the federal government?s lack of political will to enact long-term legislation funding transportation and infrastructure projects continues to be a drag on the U.S. aggregates industry.

Jan 1, 2013

By R. Hawker, P. Singh, K. V. Jessu, P. C. Pinazzi, A. J. S. (Sam) Spearing

Rock bolts are highly important underground to prevent falls of ground and thus, ensure safety. In situ, the ground reinforcement is subjected to a combination of loads, such as shear, tensile, and/or bending loads. Studies have been conducted to evaluate the effect of either shear, tensile, or bending loads on the ground support. However, only a few studies have been done to evaluate the effect of combined load on the rock bolt performance. In situ, the order of loads acting on the bar cannot be predicted, and more than one load can act on the bar at the same time. Thus, a hybrid failure criterion was developed that covered all combined loading conditions. Fifty-eight un-grouted laboratory rock bolt tests were conducted in total under two load conditions: applying shear displacement to the rock bolt and then tensile load to failure, and applying tensile displacement to the rock bolt and then shear load to failure. From the test results, the failure criterion was developed based on regression analysis. A nonlinear relationship was determined for the loading condition variations. The failure criterion presented in this paper can be used as a guide in the rock bolt capacity design under all loading conditions.

Sep 8, 2020

By Mehmet Guney

During the last decade various modifications of room and pillar and sub-level methods have been tried in an effort to eliminate gob-fires, dangers from roof falls, surface subsidence and to increase efficiency of extraction in the Armutcuk Mine, Turkey. It was eventually decided that the most likely system to give maximum benefits in view of existing geological conditions and coal seam characteristics was a system of cut-and-fill stoping employing hydraulic stowing. This paper has attempted to examine the trends of working techniques of hydraulic stowing. In addition, the results achieved and technical problems involved are discussed.

Jan 1, 1968

By K. F. Unrug

The method of coal pillar design involves primarily two aspects, the geometry of the pillar and the strength of the coal. However, the strength of the coal has to be emphasized with respect to the entire pillar dimension rather than isolated strength values of coal samples taken and measured from different locations. The presently applied pillar design systems do not specify clearly what the coal sample strength really represents. The intention of this paper is to introduce the concept of seam strength as opposed to the current practice of using coal strength as a prime design criteria in the formulation of pillar calculations. Seams are most of ten composed of multiple layers of coal, partings, and bone in different configurations, changing within the vertical section of the seam even in relatively close locations. The difference in strength between the weakest and strongest component of the coal seam could be as much as five times or more. An experimental approach based on multiple compressive tests performed on coal samples from the Coalburg and the Warfield seams from Eastern Kentucky was undertaken. The analysis of the results lead to the conclusion that for pillar calculations both the weighted mean of the seam strength and the strength of the weakest stratum should be considered rather than the relatively vague aspect of coal strength The design of pillar dimensions based on the above mentioned aspects should assure a more realistic design performance.

Jan 1, 1985

By Hiroyuki Abé

This paper is a review of research and development on geothermal energy extraction in Japan especially on hydraulic fracturing. First recent geothermal developments in Japan are outlined in Part I. An increase in the production rate of geothermal wells may be highly dependent on the geothermal well stimulation technology based on hydraulic fracturing. The hydraulic fracturing technique must be developed also for geothermal energy to be extracted from hot, dry rock masses. In Part II, the research on hydraulic fracturing and field application are reviewed.

Jan 1, 1982

By C. M. Goodall

Solids and liquid phase residence time distribution data is reported for a laboratory column flotation cell. The effects of various physical flotation parameters on residence time distributions are reported and analyzed. A plug flow model with recycle is proposed for the froth phase and a tanks in series model for the pulp. By comparison of two and three phase residence time -distribution data it has been shown that the use of liquid residence time distribution data to predict the residence time distribution of the solids in a column is not valid.

Jan 1, 1990

By Louis M. Schlesinger

KMG Minerals, Inc., a mica-feldspar-quartz producer in Kings Mountain, N.C., uses about 50% of its plant's -200 mesh slimes to manufacture brick. However, the company is unable to market the remaining 50% of this fine mineral mixture. The NCSU Minerals Research Laboratory operated a pilot plant to process these slimes to produce an additional product. The process, consisting of blunging and hydraulic sizing, was designed to separate a kaolin-enriched -270 mesh product from the bulk of the coarser +270 mesh "grit" minerals. Size analysis showed that this product was 80% finer than 20 microns and 50% finer than 6 microns (in equivalent spherical diameter). An evaluation indicated that it is a hydrous aluminum silicate that might be suitable in the filler and extender markets for traffic paint, some types of plastics, joint cements, and dusting compounds. Because of its high viscosity, it will be difficult to use more than a small percentage in cast ceramic bodies. However, it might be possible to use up to 10% in extruded ceramic bodies (i.e., electrical porcelain). The 15.2 cm (6 in,) diameter Linatex Hydrosizer was tested using a range of teeter water flowrates, so that the net rise velocity was varied from 0.10 cm/s to 0.40 cm/s. The solid feed rate to the sizer was maintained at approximately 1.1 t/hr/m2 (0.12 ton/hr/ft2). Tests were run using both "shallow" (i.e., 6 in.) and "deep" (i.e., 15 in. teetered beds. The best overall result was obtained when the sizer was operated with the "deep" teeter bed and a net rise velocity of 0.10 cm/s. About 97% of the +270 mesh material was rejected and approximately 79% of the -270 mesh material was recovered in a 14% solids slurry.

Jan 1, 1994