Search Documents

By Robert L. Grayson

An application of goal programming (GP) in evaluation of proposed purchases of major mining machinery is presented. It incorporates historical operating data compiled on mechanical delays to production time. The goal programming technique, which is an extension of integer programming, is used to maximize an objective function. The objective function combines the capital budgeting evaluation methods of net present value, payback period, profitability index, and total net earnings as goals weighted according to a management preference. The GP method gives an optimal solution to a multiple-goal problem. A sensitivity analysis is performed to determine the effect of an increased production forecast or a tightened budget on proposal selection.

Jan 1, 1982

By L. Xu

Since the establishment of the standard dust concentration of 2 mg/m3, a strong effort has been made by mining engineers and researchers to provide better dust control equipment and procedures for underground coal mines. Particular areas of success have been control of dust generation by better coal-cutting strategy, better design of water sprays for dust suppression and air movement, use of scrubbers, and improved design of face ventilation systems. A drastic improvement occurred over time such that the average dust concentrations for continuous miner operators dropped from 6.5 mg/m3 in 1968 to 1.3 mg/m3 in 1980 and for auger, cutter, longwall, and roof bolter occupations from 2.7 mg/m3 in 1973 to 1.6 mg/m3 in 1980 (Niewiadomsky, 1983).

Jan 1, 1990

By B. S. Crocker

Introduction Pebble mill grinding can be defined as wet or dry grinding in a tumbling mill with pebbles used as grinding media instead of metal balls. To clarify the terminology, which may differ in the various mineral industries, it is essential to point out the differences between grinding with partially sized and carefully sized grinding media. When grinding with partially sized media (limited top size only), sizing is usually the setting of the primary crusher and there is no bottom sizing-all fines, chips, sand, and small sizes are included. This is often called run-of-mine or primary autogenous grinding. In this case the entire crusher discharge is fed into the mill and part of it becomes "charge" and the rest is "sand feed." When grinding with carefully sized media (i.e., media that is sized both at the top and bottom of the size range), no fines or chips should be present in the charge to the mill. This is pebble milling and the grinding media consists of ore, rock, Danish pebbles, gravel pebbles, or ceramic pebbles-media that is appreciably lighter than steel balls. The grind¬ing charge is fed to the mill to maintain a load and it does the grinding usually on a classified sand product of suitable size. If the grinding media is the same as the raw material being ground, this type of grinding is also called secondary autogenous grinding. Pebble milling was in common use in the gold mines of South Africa in the early 1900s. It is by far the oldest form of autogenous grinding. It may be used to grind crushed ores from a maximum size of about -% in. to all -10 µm. Pebble milling differs from "run of mine" grinding in many ways, but two big differences are: I) The ore itself is crushed to approximately t/4 in., or it may be further reduced to 8 or 10 mesh in a rod mill or fine crusher. 2) Then carefully screened ore of the correct size is placed in one or more stages of pebble mills to grind the ore to its desired final size. The media size is carefully selected to be the most efficient for the particular size reduction required in each stage. This is a precise practice, and pebble mills can be designed as easily and accu¬rately as can rod mills or ball mills by those skilled in the art. A pebble mill is a rotating cylinder in which the grinding media has been carefully sized for the job in hand. If the mill is doing coarse grinding, the media will be correspondingly large and the mill might be called a primary (or intermediate) pebble mill or a lump mill. If it is to do fine grinding, the media selected is proportionately smaller and the mill would be called a secondary or tertiary pebble mill. The media itself is normally rounded pebbles made from screened ore from the primary-crusher discharge. The charge could be rounded pebbles of the correct size removed from a primary autogenous mill, or the pebbles could be carefully sized gravel, sized beach pebbles, or sized flint pebbles. Usually the specific gravity of a pebble is from 35 to 55% of that of steel balls. It commonly varies from 2.66 to 4.2, depending on the specific gravity of the ore. Primary pebble mills, or lump mills, would be charged with pieces of rock up to 10 in. maximum and 5 in. minimum and would grind crusher discharge with a maximum size of 1/4 in. on hard ores and 3/8 in. on softer ores. Secondary pebble mills could be charged with pieces of rock screened on 4 x 4-in. square mesh and retained on 1 1/2 x 1 1/2 in. These mills would grind material with a top size of 8 to 10 mesh. Tertiary pebble mills could be charged with screened rock that would pass 3 x 3 in. and be retained on 1 x 1 in. and grind 35 to 48 mesh sands. Principles of Operation Media Size To operate a pebble mill efficiently it is imperative that great care be taken in screening the rock feed that is fed into the mill to round up into a range of pebble sizes that are suitable for grinding of the sands that are also being fed into the mill, having regard to the top size and the average size of such sands. Since most mill operators know from experience the correct size of steel balls to be used in a mill to handle different sizes of sand feed, it is convenient to relate the pebble size to a ball size. If the correct ball size is not known, it is relatively simple to conduct batch laboratory tests in 12- to 18-in. laboratory mills to determine the optimum size of steel ball. Also, Bond and others have published formulas for calculating the optimum ball size. When the correct size of the individual steel ball is known, then a pebble of the same weight will perform the same grinding if used in the proper size of mill and under the proper conditions, which will be defined later. This media size, as defined by the average weight of the individual pieces, is most important. The following tests will serve to clarify this point. Laboratory Tests Using Steel Balls or Pebbles. Several labora¬tory grinds were made to compare a given size and weight of steel ball with a pebble of the same weight but larger size, and of the same size but lighter weight. The following loads were used in the 12-in. laboratory mill: All 1 1/4-in. steel balls weighing 122 ± 10 g. All 1 3/4-in. pebbles weighing 123 ± 5 g. All 1 1/4-in. pebbles weighing 45 ± 3 g. To equalize capacity, the test with the steel balls was run only 34% as long as the tests with pebbles. In each case, 2,500 g of primary sands were ground at the optimum gravity for the media being tested at a speed 78 1/2 % of critical speed, and for 170, 340, and 680 revolu¬tions for the steel balls, and 500, 1,000, and 2,000 revolutions for the pebbles. The first test is summarized in Table 74 by showing the 80% passing size in microns for the feed and for each of the grinds. Two other tests are summarized in Table 75 showing the screen analyses

Jan 1, 1985

By Michael Day, Paul Kos, Scott Brinton

Quantitative hydrogeologic characterization of fractured rock is challenging because fracture systems are convoluted and difficult to characterize discretely. For large-scale water resource impact analyses, it may be more appropriate to use a watershed water balance approach and analyze fractured systems in terms of “bulk” hydraulic parameters over a large enough scale (hundreds of meters), so that the fractured media may be evaluated as “equivalent” porous media [1]. This is a common investigative methodology for mountain watersheds in fractured bedrock terrain because it does not rely on discrete flow paths but instead evaluates inputs to (recharge) and outputs from (discharge) the ground-water system [2,3]. This paper describes the use of this methodology to perform a practical and cost-effective hydrogeologic characterization and mining impact analysis for a proposed granite quarry in a mountain watershed. The key conclusions of the study guided the mine planning that was designed to minimize impacts to the fractured granite hydrogeologic system and preserve recharge to downgradient sedimentary aquifers.

By A. T. Stroebel

Diatomite deposits, the skeletal remains of tiny aquatic plants called diatoms, are found in many parts of the world. Only a few of these de- posits are of commercial value. Open pit mining is used in nearly all deposits now being worked. Processing methods range from simple drying, crushing, sizing and packaging to carefully controlled and highly sophisticated calcining and air classification procedures, employing the latest control and testing techniques. The major uses of processed diatomite are in filtration as filter aids and fillers and extenders.

Jan 1, 1979

By Edwin H. McKee

Eruption of rhyolitic ash-flow tuffs in the area of the McDermitt (Cordero) caldera began about 17.4 m.y. ago and continued for about 1.5 m.y. During this period of silicic eruptions, a circular area about 30 km in diameter collapsed to form a caldera that subsequently filled with sedimentary and volcanic rocks. 3 A total of more than 200 km of silicic rocks was erupted from the volcano. The final phase of igneous activity, about 15.5 m.y. ago, included resurgent doming and intrusion in the central part of the caldera. Three to 4 m.y. later +I2 m.y. ago), hydrothermal solutions using the northern part of the caldera ring fractures as conduits deposited cinnabar, pyrite, alunite, and other minerals in tuffaceous lake beds and volcanic rocks accumulated within the caldera. The ore-forming solutions may have been a residuum from the silicic magma or connate water or ground water heated by the still-hot resurgent magma in the central part of the caldera. The source of the mercury has not been identified. Later oxidation of the sulfide minerals and redistribution of the supergene minerals corderoite, several mercury nitro-oxychlorides, marcasite, iron, and titanium oxides in the sedimentary rocks account for most of the newly discovered ore body at Cordero.

Jan 1, 1976

By Ray Brainard, Adriana Ventimiglia, Amanda Kerr

Preliminary design is underway for a new Southern Nevada Water Authority (SNWA) project that will ensure one of America’s most reliable water systems by providing continued, reliable water service to existing and future customers. The Horizon Lateral is a $1.6 billion water transmission pipeline that includes 7–10 miles of 108-inch finished diameter rock and soft-ground tunnels. The tunnels will traverse volcanic rock in or around the McCullough Mountain Range and the surrounding alluvial basin. The tunneling community will find relevance in hearing about this critical infrastructure project from a leading wholesale water utility owner with a proven track record for on-time, collaborative projects.

Dec 1, 2022

By Egons R. Podnieks, Wallace W. Roepke

Mining technology to utilize vital lunar resources will be required for any commitment to permanent lunar basing. Lunar mining must be viewed both as a major supporting element for space resource commercialization and for creation of human settlements on lunar and planetary surfaces to support long-range space exploration. The Apollo missions to the lunar surface and results from fundamental research on analogue lunar rocks by the Bureau of Mines, and others, have provided the initial data for developing lunar mining technology. The multi-disciplinary research projected in this paper outlines the scientific and engineering needs to realize the lunar mining goals.

Jan 1, 1990

By Lei Pan, Venkata Atluri, Xuming Wang, Yuesheng Gao, Jan D. Miller

Polysaccharides have been used as depressants for naturally hydrophobic talc in the flotation of base metal sulfide ores, precious metal sulfide ores and platinum group metal (PGM) sulfide ores. The results of this surface chemistry study confirm guar gum as a preferred polysaccharide for talc depression in the flotation of these ores. In addition to the practical application of the research results, the surface chemistry results are of academic significance, providing further information to understand how polysaccharide depressants function in these complex sulfide flotation systems.

By Graham A. Brown

Activities in offshore mineral exploration In Australia are increasing almost daily, at such a rate that this report will rapidly become out of date. At the time of writing, February 1967, there were no commercial discoveries of offshore minerals reported in Australia, although there has been definite encouragement in many fields. While this initial encouragement has not revealed any commercial mineral deposits offshore hopes are running high in Australia for success in 1967. Why should mineral deposits be expected offshore in Australia in the first place? The reasons are many. The minerals to be discovered also are many. The reasons are based on the history of alluvial and beach mining activities in Australia's past and at the present time, and on the physical environment of the vast Continental Shelf which surrounds the continent. A brief examination of the two primary features which are necessary before offshore mineral exploration can be contemplated should be, undertaken. Two favourable environments are necessary; firstly a Continental- Shelf to form a physical environment for the accumulation of the mineral deposits, and secondly a favourable political-legal environment to give the exploration companies adequate protection during exploration, and suitable long term arrangements for the exploitation of the deposits after discoveries have been made. Australia is well endowed with both of these.

Jan 1, 1967

By Sergio Estebanez, Martha Gross, Ruben Rubal, Yvonnick Rescamps, Alexandre Cochennec

The Hampton Roads Bridge-Tunnel (HRBT) Expansion project in coastal Virginia, USA will add two 1.5-mile (2.4 km) TBM bored tunnels alongside two existing immersed-tube tunnels between artificial islands. The site’s unusual constraints and the requirements of a large-diameter variable-density TBM shaped the design-builder’s decisions for handling TBM inputs and outputs, siting the TBM plant and supporting equipment, and sequencing tunnel-construction operations. This paper addresses the logistics necessary to enable key functions of the 46-ft (14-m) TBM and its ancillary equipment, including transport of most materials by barge, U-turn of the TBM on an artificial island, and delivery of materials for the second tunnel through the first one while interior structures are under construction.

Jun 13, 2021

By Nikolaos Syrtariotis, Mark Berger, Timothy O’Brien, Vojtech Gall

The Northeast Corridor Superconducting Maglev Project (SCMAGLEV) entails construction of a high-speed train system between Washington, DC and New York City, with the first leg between Washington and Baltimore, MD. This innovative project will shorten travel times between Washington DC and Baltimore to approximately 15 minutes, and connect Washington, DC to New York City in under an hour. In 2021 the draft EIS is expected to be issued for comment with a Final EIS/ROD anticipated by early 2022. This paper provides an update on the project as presented in Gall et al. (2020) and discusses the economic and environmental benefits, preferred alignment alternative, preliminary staging and launching of the TBMs for construction, and preliminary station design.

Jun 13, 2021

By J-M M. Rendu

Geostatistics are increasingly recognized as powerful tools for reserve evaluation and grade control. It is also generally accepted that geologic input is required for the results of a geostatistical study to be meaningful. The role of the geologist is significant at all stages, whether it be to oversee the creation of the database, to assist in the statistical and semivariogran studies, to ensure appropriate block evaluation and kriging, or to review the results obtained. However the link between geology and geostatistics is often complex and not well understood. A presentation is made of the areas where geologic input is needed, and of the tools which the geologist should have at his disposition to ensure that his role is fulfilled. Organization of a Geostatisticel Study To be acceptable as the basis for financial investment, a geostatistical reserve estimation should be composed of four phases, the last phase being optional: Phase 1 - Background discussions, Phase 2 - Computation, Phase 3 - Reserve reporting, Phase 4 - Reserve audit. During the background discussions (Phase 1) the role of the geologist is primordial, as it is then that most decisions will be made concerning the geologic factors to be included in the geostatistical model.

Jan 1, 1985

By R. L. Bullock

The New Lead Belt of Missouri, situated in the heart of the Clark National Forest, stands as a dynamic example of how mining activities can successfully coexist in a restricted wilderness area. After 16 years of intensive drilling activity, mine development and surface plant construction, many would agree that the mine-plant design philosophy of St. Joe has minimized the imbalancing effects to the ecology and the wilderness appearance of the Ozark area. In a recent dedication speech of St. Joe's newest operation, it was stated: 1 "this Brushy Creek Mine, as well as nearly all of the mines in this district, lies within the boundaries of the Clark National Forest. Here the Forest Service has an outstanding and realistic program for multi-use of Federal lands. Mining, lumbering, recreation and conservation coexist in, what I consider, a delightful wilderness environment. I believe that this same type of usage could be permitted on all government land without seriously detracting from its natural beauty." Each and every activity in the process of discovery, exploration, development and finally operating a mine and process mill could have drastically degraded some phase of nature's environment were it not for the well developed and executed plans of the mining people involved. This is not to say that everything has been kept in perfect balance; but most certainly the industrial impact on what was once a wilderness area has been held to a minimum. What follows is the story of how each phase of this gigantic development was handed by industry people. Through their interaction and cooperation with government agencies, educators and researchers, allowed not only the ecology of the area to be protected, but the aesthetic beauty of the Ozarks to remain intact.

Jan 1, 1973

By Adam Levy, Thomas Novak, Sampurna Arya, Joseph Sottile, Kozo Saito

The use of a woven wire-mesh screen as part of a flooded-bed dust-scrubbing system is popular in the underground coal mining industry. It is used in combination with a demister (mist eliminator) to remove dust from the dust-laden air. A study was conducted to measure the pressure drop across a flooded-bed, wire-mesh screen at different airflow rates in one-phase (dry) and two-phase (wet) conditions. Two empirical relationships between pressure drop and air velocity were developed for dry and wet conditions, respectively. In both cases, the form of the empirical relationships was found to be similar to relationships given by Sabri Ergun for high velocity, non-Darcy, single- and multi-phase flow through porous media. The experiments were repeated on a reduced-scale model of the wire-mesh screen, and the pressure-velocity relationships obtained from the full-scale prototype experiments were tested. The test results show validation of the full-scale empirical formulae on the small-scale model with an insignificant variation. This paper presents the empirical equations for pressure drop across the wire-mesh screen in dry and wet conditions. Researchers can use these equations as a tool to predict total pressure drops for wire-mesh screens of different scale sizes.

By Allan H. Caverson

Over the past nine years a means for measuring the distance between the mine roof and floor has been developed at the White Pine Mine which yields relevant information utilized in the mining operation. The technique known as "convergence!' is an efficient, low cost way for obtaining large quantities of data for predicting roof falls, caving activity, and overall mine stability. From a limited introduction in 1964 related to monitoring an experimental longwall project, the activity of convergence measurements has been expanded to become a production tool now found in all sections of the mine. Presently, the program involves four main types of activity: 1. Monthly measurements in areas known to be active, and in sample blocks scattered throughout the mine for a long-term stability study. 2. Semi-monthly measurements along vital travel roads, belt drifts and compressor sites. 3. Weekly measurements in areas where men are working. 4. Daily measurements in pillar-recovery and caving operations. Today, one field engineer and six technicians are involved full time in convergence work. Rock Mechanics technicians have installed approximately five thousand stations since the start of the program and of this number, over twenty-five hundred active stations still comprise the mine-wide network spread over the more than five square mile extent of the White Pine Mine workings.

Jan 1, 1973

By S. Maurigiannakis

In an effort to promote sustainability in the construction industry, the natural decorative stones that cover large external areas of buildings may be replaced with artificial stones. In this paper the physical and mechanical properties of artificial decorative stones are presented and are critically compared with corresponding natural stones. To test suitability for various applications, artificial stone specimens were subjected to weathering testing (freezing-thaw cycles in a climatic chamber). Mechanical characterization of these specimens was based on uniaxial compressive testing as well as non-destructive ultrasonic testing. Preliminary results show that artificial stones can replace natural stones, thus creating a sustainable development option for the construction industry.

Jan 1, 2003

By R. B. Hawkins

The discovery of the gold deposits of the Jerritt Canyon district and the construction of the E. R. Bell Mine is one of the significant mining developments in the United States during the past ten years. This mine will exploit one of the larger deposits of disseminated gold presently known, with proven, recoverable reserves in excess of 67.6 million grams of gold. Interest generated by the success of this project has contributed greatly to the tremendous resurgence in exploration for disseminated gold deposits in Nevada and throughout the west. The Jerritt Canyon project, including the Bell Mine, is a 70/30 joint venture between Freeport Gold Company and FMC Gold Incorporated, both of which are wholly owned affiliates of the respective parent companies, Freeport-McMoRan, Inc. and FMC Incorporated. Under the terms of the joint venture agreement, Freeport Exploration Company, another Freeport-McMoRan affiliate, manages the exploration and pre-mine development. Drilling, design, construction and management of the Bell Mine are provided by Freeport Gold Company.

Jan 1, 1982

By C. Clark, J. Seymour, D. Benton

"National Institute for Occupational Safety and Health NIOSH is conducting research on jackleg use and related accidents in underground metal mines. This paper provides an analysis and overview of jackleg drill usage, accidents, operational characteristics, and alternatives, based on information from injury reports, legacy research, stakeholder input, and published literature. Jackleg drills are involved in more ground fall accidents in underground metal mines than any other drill. Jackleg-related injuries are most prevalent at the face in the course of installing initial ground support. Alternatives to jacklegs for drilling and bolting under incomplete support in narrow underground openings are not yet available. Small mechanized bolting equipment needs to be developed to address jackleg-related accidents and improve safety at mines where jacklegs are being used. JACKLEG DRILL Description The term “jackleg drill” is a generic name for a class of handheld, rotary, percussion rock drills that are equipped with an attached reaction leg to provide stability and thrust for the drill (Figure 1). All of the drill and leg controls are located near the operator’s handle at the rear of the head portion of the drill. Jacklegs are classified according to the bore size of their pneumatic pistons which normally range from 6.03 to 8.26 cm (2.375 to 3.25 in) [Kurt, 1982; Clark, 2012]. Jacklegs typically weigh 460 N (103 lbs), but their weight can approach 535 N (120 lbs) after they are fitted for operation with drill steel and air and water hoses [McKibbin and Clark, 2001]. In underground mines, jackleg drills are commonly used to drill 3.8-cm (1.5-in) diameter holes 1.83 m (6 ft) deep in rock. Application The jackleg drill is primarily used in underground mines when the size of the ore body, the ground conditions, or the mining method do not permit large openings to be mined using mechanized equipment (e.g., narrow vein mining). Jacklegs are used to drill blast-holes for explosives and also holes for installing ground support. These versatile drills are used in nearly all phases of mining including exploration, development, production, and maintenance [Kurt, 1982; Williams et al., 2007; Chen and McKinnon, 2012]. The jackleg is used to drill holes in rock using drill bits attached to hollow steel bars called drill steels (rotary percussion drilling). After the hole is drilled, the jackleg can be used to install different types of ground support components, depending on the ground conditions and the specific ground support measures that are needed. For example, the jackleg can be used to install expansion-anchor rockbolts or resin-grouted rockbolts using the drill’s rotary-motion feature. On the other hand, the jackleg can also be used to install friction-type Split-Set™ rockbolts using the drill’s percussion (hammer-motion) feature. As shown in Figure 1, various washer-like bearing plates can be installed along with these bolts to provide additional ground support and to help secure surface control products, such as wire mesh and shotcrete that are in turn used to retain small, loose material between the bolts [Clark, 2012]."

Jan 1, 2016

By John E. Feddcck

New York City's $360 million North River Water Pollution Control Project is part of New York State's plan to clean up the Hudson River. The project is to provide a sewage treatment facility capable of accomodating a peak waste water flow of 330 MGD which will in great measure eliminate the 192 MGD of raw sewage that N. Y. C. discharges into its surrounding waters. Eleven miles of intercepting sewer lines must be constructed along the west side of Manhattan Island to service approximately one-half of the island. The first contract award was for a 4134 ft. sewer tunnel with a finished inside dimension of 16' x 16'. This main intercepting sewer will feed a sewage treatment plant located on and adjacent to the Hudson River. The tunnel is parallel to the river and is located under 12th Avenue between 125th Street and 143rd Street. The Penn- Central Railroad tracks are above and just to one side of the tunnel location. The working tunnel diameter is 21 ft. and numerous problems of support, mining method, and ground control have been encountered. (see Dwg. 1)

Jan 1, 1970