Search Documents

By Feng Junfa, Du Feng, Li Huamin, Syd S. Peng

"The Ordos coal field is located in the northern midwestern part of China (Fig. 1). Since the mid- 1980s, it has been developed into one of the major coal fields in the world, producing approximately 833 Mt (918 million st) of raw coal in 2013. There were once more than 400 coal mines operating in the region. However, due to the combination of market conditions and implementation of government consolidation policies, the number of coal mines operating in recent years has been reduced considerably, with increasing output.The surface of the Ordos coal field is covered with loess and alluvium layers of varying thicknesses. In many areas, their combined thickness may amount to as much as 100 m (328 ft) underlain by thin bedrock. Many loess and alluvium are aquifers receiving water from rainfalls. There are also gullies of varying depths crossing the coal field. Figure 2 is a typical stratigraphic column highlighting the coal seams and roof and floor rocks of interest.In conjunction with the development of highproductivity coal mines, numerous ground control instrumentation tests have been conducted in the operating longwall panels. Analyses of the results of those tests offer the opportunity to understand the effect of wide-ranging mining and geological factors on the overburden movement. For this reason, trips were made to coal mines of interest to interview mine management and collect their unpublished internal research reports on ground control instrumentation. In addition, literature searches on published thesis/dissertations and papers in the professional journals were performed. Finally, data from a total of 95 fully mechanized longwall panels were collected. The instrumentation involved primarily the monitoring of hydraulic pressures of longwall shields, from which the first roof weighting and first roof caving interval and periodic roof weighting and periodic roof weighting interval were identified and determined. Some panels also included measurements of roofto- floor convergence at the face, roof strata bed separation, longwall face sloughage and the height of caving and fractured zones in the overburden. Those 95 panels were located in 20 coal mines (Fig. 1) congregated along both sides of the Wulunmulun River with the following mining and geological conditions. All together those 20 mines produced more than 224 Mt (246 million st) in 2013, accounting for approximately 27 percent of the total coal production in the Ordos coal field:1. Period of mining: 1991-2013.2. Mining methods: All panels employed the one slice, full-seam natural-caving longwall mining method like those practiced in the United States. All panels were developed with a twoentry system with a single-row of chain pillars measuring 20- x 20-m (65.6- x 98.4-ft) wide.3. Coal seams (Fig. 3): Coal in Ordos coal field is high-quality steam coal, that is very low in sulfur, potassium and ash, but high in Btu. Data were collected in panels mined in a total of 10 seams with 82 panels in four seams and the remaining 13 panels in six seams. The first six seams (1-2, 2-2, 3-1, 3-2, 4-2, 5-2) were mined by the Shenhua Coal Group (the world’s largest coal company) and the #4-2, 5-2, 6R, 62, and 62R seams were mined by both the Shenhua and Yitai Coal groups. In each coal group, the sequence of mining was in descending order. For example, in Shenhua Group, the top seam 1-2 was mined first, followed by the 2-2, 3-1, 3-2, and 4-2 seam in that descending order. In Fig. 3, the top-down sequence of coal seams is listed from left to right in each coal mine group. All seams were near horizontal with dip angles less than 3°."

Jan 1, 2014

By Dirk van Zyl

It can systematically assess if the control and management systems designed for protection of sensitive ecosystems are adequate. The results of the assessment can help to identify key elements in the project that pose higher risks due to uncertainties in design. These assessments can then be used to make recommendations to further manage and reduce risks as the project is developed. QUALITATIVE RISK ASSESSMENT The general principles of a risk assessment are well summarized by Kaplan and Garrick (1981): "In analyzing risk we are attempting to envision how the future will turn out if we undertake a certain course of action (or inaction)." Fundamentally, therefore a risk analysis consists of an answer to the following three questions: What can happen? (i.e. what can go wrong?) How likely is it that that will happen? If it does happen what are the consequences?" Risk assessments can be performed using various levels of sophistication depending on the amount and accuracy of data available. A qualitative risk assessment uses descriptors throughout to express the level of risk. The definitions of the descriptors are presented in terms of the magnitude or concentration of contaminants. The results of a qualitative risk assessment can be used to: a)Document the evaluation and decisionmaking process. Although differences of opinion may exist about the definitions of the descriptors, the process is well-documented; b)Express the relative risk associated with specific activities or design elements; and, c)Select those failure modes or release mechanisms that may result in significant risks. These mechanisms can then be further developed in quantitative risk assessments. A qualitative risk assessment can be performed in a systematic approach using four steps (Van Zyl, 1987): A qualitative environmental risk assessment can be used to describe the risks associated with the development of a new mine and to make an evaluation of the adequacy of its design for environmental protection. The relative magnitude of risk associated with selected failure modes and exposure/consequence scenario assessments is the final result of a qualitative risk assessment. These failure modes are based on site specific areas and components, and mining and construction phases. The four steps of a risk assessment (hazard assessment, exposure assessment, consequence assessment, and risk characterization) are used in the development of a qualitative risk assessment. Relative magnitudes (using a five point scale of negligible to high) for each step, can be quantified in a qualitative risk assessment. Development of the descriptors for the relative magnitudes in each step is a very important part of a qualitative risk assessment. The success of a qualitative risk assessment depends on the adequacy of the information base and the subjective judgements made in each step. The quality of the risk assessment is, therefore, dependent on the experience of the assessors. A mining project in a sensitive coastal environment is presented as an example to demonstrate the application of a qualitative risk assessment. INTRODUCTION Environmental impacts from mining operations have been a significant factor in the last century. This was especially the case prior to the development of a better understanding of environmental processes and the potential impacts of acid rock drainage (ARD), and associated heavy metals, or the uncontrolled disposal of tailings and waste rock (Smith, 1987). Much care has been exercised over the last two decades in designing and operating mines to limit the environmental impacts as far as possible. All new mines are specifically designed with mitigative methods to manage such potential environmental impacts. Attention is directed to ARD impacts, safe disposal of mine waste rock and tailings, transportation and storage of chemicals and fuels, and final reclamation. A qualitative risk assessment can be used to address all project systems and activities that may potentially pose a risk to the environment.

Jan 1, 1992

By William W. Wellborn

Abrasives are substances both natural and synthetic that are used to grind, polish, abrade, scour, clean, or otherwise remove solid material usually by rubbing action (as in a grinding wheel), but also by impact (pressure blasting). Facts about the discovery, early use, adaptation, and development of abrasives prior to the 20th century are few. From the sparse, earliest information that is available, it would appear that the science of abrasives began when, to fashion his tools, man began to select certain kinds of rocks in preference to others because of their peculiar properties. There is evidence that stones were sawed by some sort of grinding machine as early as 4000 BC in Egypt. The real expansion of abrasives use coincided with the beginning of metallurgy in the Middle East around 2000 BC. The earliest confirmed use of abrasives for grinding metal comes from a steel dagger found along with a sharpening stone which was dated at about 1500 BC. Natural and manufactured abrasive substances play an important role in fashioning and finishing numerous products with a wide variety of end-use applications. The mining and preparation of crude, natural abrasives for their markets and the manufacture of synthetic and other abrasive materials contribute significantly to the US economy (Table 1). In addition, just as sawing to specific dimensions enhanced the value of the Egyptian stone, the use of abrasives in fabrication of modem products, and the addition of abrasives to others, add value. GENERAL CONSIDERATIONS The most important physical properties of materials that qualify as abrasives are hardness, toughness (or rigidity), grain shape and size, character of fracture (or cleavage), and purity (or uniformity). To fabricate bonded abrasive products such as grinding wheels, additional considerations include stability under high heat and bonding characteristics of grain surfaces. The economic factors of cost and availability are always important. No one singular property is paramount for any use. For some applications extreme hardness and toughness are needed, as in diamonds for drill bits. For other uses, factors of greatest importance are hardness and ability to break down slowly and, in the process, develop fresh cutting edges when grains become worn. In garnet sandpaper, for example, highly cleavable, friable, or extremely tough grains are not desirable. For other uses, extreme hardness may be objectionable. Abrasives for dentifrices and for glass-cleaning soaps are cases in point. For the most efficient uses in more critical applications, different types of abrasives are rarely completely interchangeable. While crushed quartz and garnet are both used in sandpaper, the two abrasives are not at all interchangeable in their applications. In the final analysis, the choice of a high-grade abrasive depends upon the quality and quantity of work performed by the abrasive per unit of cost. Initial cost of an artificial abrasive may be much greater than that of a natural abrasive, but the artificial mineral may do so much better work and do it so much faster that the ultimate cost is less. It is for this reason that artificial abrasives have largely replaced natural abrasives.

Jan 1, 1994

By Alphonce Wikedzi, Mussa D. Budeba, Samwel V. Manyele, Sospeter P. Maganga

The present study provides an overview of the challenges and opportunities in processing complex gold-copper ores. The systematic literature review was conducted using Scopus database and seven-step methodological approach. The study indicates that the major challenges in processing complex gold-copper ores through the conventional cyanidation method include (1) increase in cyanide consumption; (2) increase in cyanide destruction cost; (3) low gold recovery; (4) decrease in adsorption efficiency; (5) decrease in electrowinning efficiency, and (6) difficulties in the measurement of free cyanide concentration in the leaching system. Moreover, the study indicates that several methods have been developed and some have been implemented in the mining industry for processing complex gold-copper ores. This includes ore segregation, pre-aeration, pre-treatment methods (e.g., ammonia), alternative lixiviants (e.g., thiosulfate, thiocyanate, glycine), cyanide destruction methods, and cyanide and copper recovery technologies. The study concluded that using lixiviant mixtures (e.g., cyanide-glycine), pre-treatment with environmentally friendly reagents (e.g., glycine) and the integrated membrane-based process (SuCy process) are new directions in processing complex gold-copper ores. However, more investigations are required to advance these processes to a commercial scale.

Sep 30, 2023

By B. Simser, T. Butler, A. Hall

The longterm future of Glencores’ mining operations in the Sudbury basin area of Ontario, Canada likely depends on mining deposits at depths below two kilometres. To gain a better insight into the rockmass response to mining, a geological scouthole program has been implemented at Glencores’ Nickel Rim Deep and Onaping Depth Project to gain insight into rockmass conditions ahead of the devel-opment face. The scouthole program involves drilling long (up to 600 m) subhorizontal boreholes drilled ahead of the development end and collecting data about the rockmass conditions from various geophysi-cal and mechanical tools (in addition to conventional core logging). Once all data has been collected and the borehole is available, seismic sensors are installed up to 450 m down the hole as part of the micro-seismic monitoring program with the leading sensor always located ahead of the development end. The recorded seismic data is used to provide realtime insight into the rockmass response to mining. On May 20, 2017 a flurry of seismicity with a maximum moment magnitude (Mw) of 0.7 occurred causing damage to the ramp heading. Data from the microseismic monitoring system had indicated that conditions at the development end were changing prior to the rockburst. A back analysis of the scouthole data indicated a clear anomaly in the rockmass at the location of the rockburst. The scouthole data also provided sufficient information to suggest that once this anomalous zone was exited, mining conditions would improve. With the microseismic monitoring system providing realtime information from the rockmass, the area was re-habilitated and ramp development continued successfully. Details of the rehabilitation and adjustments to the ramp development are discussed. Some correlations between the scouthole data and recorded micro-seismicity are also presented.

Apr 26, 2022

By S. C. Gambrell

Support characteristics of in-cycle trusses are analyzed using a photoelastic model loaded by tightening a truss in the sequence normally used in an underground mine. Stresses in the roof at its center point and at the junction of the roof and rib are examined. Effects of zero tension and unequal tension in the inclined anchor rods are presented. Effects of simulated subsidence on stress in the roof surface and on tension in the separate truss members are examined. Conclusions are drawn relating to (1) the effects of tension in the inclined anchor rods on uplift and compressive stress parallel to the roof surface, (2) the effects of subsidence on stress in the roof surface, and (3) the effects of subsidence on tension in the truss members.

Jan 1, 1987

By Richard C. Travis, Edward C. Dowling

A detailed kinetic study of the flotation installation at the Metcalf Concentrator revealed a rougher flotation circuit operating under less than optimal conditions. Based on these results, a project was initiated to approximately double the rougher flotation capacity by increasing the installed volume from 780 cubic meters to 1,560 cubic meters. This project, which was completed in early 1991, replaced the existing cells with larger capacity cells. A comprehensive analysis of results demonstrates significant metallurgical benefits. INTRODUCTION/BACKGROUND The Metcalf Concentrator is located in Morenci, Arizona and is part of Phelps Dodge Morenci, Incorporated. Sumitomo Metal Mining of Arizona is a minority partner in the operation with 15% interest. The Metcalf Concentrator is the newer and smaller concentrator and operates in conjunction with the Morenci Concentrator. Operating capacity at Metcalf is currently 48,000 TPD of ore on a 365 days per year basis. The Metcalf Concentrator was commissioned in 1974 at a 30,000 TPD operating rate for the purpose of treating ores originating in the Metcalf Mine. The mine takes its name from the former town of Metcalf which was named for Robert Metcalf who was credited with discovery of the mineral district. The predominant ore mineral is chalcocite which occurs as a secondary enrichment closely associated with iron pyrite. The host rock is largely granodiorite and quartz monzonite. The original rougher flotation circuit consisted of a total of six rows of Wemco 8.5 cu. meter (300 cu.ft.) flotation machines treating pulp from the two grinding sections (Sections A and B). Each row was configured in a 4-4-4 arrangement. Shortly after startup the throughput rate was increased significantly without sustaining a recovery loss. This increase was achieved by raising the target value for the particle size of the cyclone overflow which is the rougher flotation feed. Shortly thereafter, the capacity of the pump and cyclone began to restrict further increases in throughput. After testing, two 66 cm. (26-in.) cyclones and a 12-in. X 12-in. centrifugal pump replaced the original classification equipment. As a result of these modifications, the grinding section could routinely process in excess of 42,000 TPD. Due to the increased tonnage rates, limitations in the rougher flotation circuit performance were observed. In an effort to improve the performance of rougher flotation with this higher throughput, the speed of the flotation mechanisms was increased from 230 RPM to 250 RPM. This change improved the suspension of the coarser feed and induced additional air into the pulp. It did, however, apply additional strain to the motors, shortening their life. At these elevated processing rates, it was found that the dart valves operated almost entirely at the top end of the control range and could not efficiently handle upsets from the grinding section. This was remedied by lowering the end overflow weir and allowing some of the tailings to overflow the end weir. However, in order to obtain acceptable recovery levels, the flotation pulp was maintained at a high level, adversely influencing the rougher concentrate grade.

Jan 1, 1993

By Diler Katircioglu-Bayel

This study aims to investigate the effect of combined mechanical and ultrasonic milling on the size reduction of talc. Firstly, the talc sample was wet ground in a stirred media mill for five different times (30, 60, 90, 120, and 150 min), and the optimum result was subsequently achieved with treatment by ultrasonication. The effects of amplitude (20, 35, and 50 μm), solid content (2.5, 5, 7.5, and 10%), and sonication time (60, 120, and 240 min) on the sizes of the final product were investigated. The pre-milling by wet grinding caused a decrease in the grinding resistance of talc. Sequential ultrasonic treatment, which was applied to the talc sample, generated smaller particles in comparison to those acquired by stirred media milling alone. Experimental results were assessed based on the product particle size (d10, d50), reduction ratio, and specific energy consumption. Submicron particles prepared by ultrasonic treatment were perfectly stable compared to stirred media milling alone as investigated in terms of particle size. In addition, the effects of mechanical and ultrasonic milling on structural properties of talc particles were characterized by XRD analysis.

By Diler Katircioglu-Bayel

This study aims to investigate the effect of combined mechanical and ultrasonic milling on the size reduction of talc. Firstly, the talc sample was wet ground in a stirred media mill for five different times (30, 60, 90, 120, and 150 min), and the optimum result was subsequently achieved with treatment by ultrasonication. The effects of amplitude (20, 35, and 50 μm), solid content (2.5, 5, 7.5, and 10%), and sonication time (60, 120, and 240 min) on the sizes of the final product were investigated. The pre-milling by wet grinding caused a decrease in the grinding resistance of talc. Sequential ultrasonic treatment, which was applied to the talc sample, generated smaller particles in comparison to those acquired by stirred media milling alone. Experimental results were assessed based on the product particle size (d10, d50), reduction ratio, and specific energy consumption. Submicron particles prepared by ultrasonic treatment were perfectly stable compared to stirred media milling alone as investigated in terms of particle size. In addition, the effects of mechanical and ultrasonic milling on structural properties of talc particles were characterized by XRD analysis.

By K. H. Nimerick

Froth flotation of coal is growing in importance and complexity. Some of the reasons for these changes follow. 1) A need exists for energy resource conservation. 2) Preparation plants are processing widely varying coal -- deep seam, strip and stockpiled either separately or as blends. 3) More fines are being generated because more mines are using automatic mining equipment. 4) It is more practical and economical to remove ash and sulfur at the preparation plant than during utilization.

Jan 1, 1982

By Douglas Ball

An underground storage field is a gas field where man, not nature, has put all or most of the gas. All but one of those in use today are in the pore spaces or "porosity" of sedimentary rocks, the most common being sandstone. The one exception, near Newcastle, England, is a gas storage in a cavern dissolved from rock salt. The tens of millions of barrels of LPG (liguified petroleum gas) now stored in salt caverns mined in shale is liquid storage, not gas storage, and in this paper I recognize the presence of these installations but do not include them in the gas storage category, Since, with the English exception, gas storages are gas fields, they can all be sorted into the categories used to describe gas fields, 95% of them once gas fields anyway, but some of the remaining 5% are the ones having the greatest effects on underground waters.

Jan 1, 1960

By B. Berg, J. Stephenson, J. Mansanti, C. Nyikos

"Intrepid Potash, Inc.’s Carlsbad East facility has refined sylvite and produced muriate of potash (MOP) since 1965. In addition to MOP, Intrepid Potash began recovering the mineral langbeinite from a mixed ore reserve in 2005. In 2011 a new langbeinite recovery process for the coarse (+850 micron) size fraction was constructed to enhance the overall langbeinite recovery. Based on the limited mixed ore reserve and an abundance of langbeinite ore reserves the transition of the East plant to a langbeinite only facility was targeted for 2021. Due to a decreasing grade of the mixed ore reserve, declining sales pricing, and high sylvite operating costs a strategic decision was made to accelerate this transition into 2016. To enable a successful transition, a fines recovery system needed to be developed, constructed and implemented. This paper describes the advancement of langbeinite processing at Intrepid Potash and the planning, development and successful execution of the transition to a langbeinite only operation. BACKGROUND Langbeinite (K2SO4·2MgSO4) is a double salt containing potassium sulfate (K2SO4) and magnesium sulfate (MgSO4). It is used as fertilizer and in the industry is described as Sulfate of Potash Magnesia. It is attractive as a specialty fertilizer and in addition to containing a ready source of a primary nutrient potassium, it also provides two secondary essential nutrients, magnesium and sulfur. It is especially attractive for chloride sensitive crops. Langbeinite has a specific gravity of 2.8, a Mohs hardness of 4.2, and is brittle thus very friable. It is the hardest of the saline minerals, and despite its relative softness on the Mohs scale can be very abrasive in process environments and in field applications, probably due to its conchoidal cleavage. Its solubility at 240 g/l is less than the solubility of sylvite (KCl) or halite (NaCl) and due to even slower relative dissolution kinetics washing with cold water has been a common practice for upgrading langbeinite ores. The solubilization/crystallization relationship for langbeinite is different from the majority of other evaporite minerals in that once langbeinite is solubilized it does not form langbeinite again. Instead it gives up one mole of magnesium sulfate, takes on various waters of hydration and precipitates out as either schoenite (K2SO4·MgSO4·6H2O) or leonite (K2SO4·MgSO4·4H2O) depending on temperature. Due to its partial solubility and phase transitions at its surface when exposed to moisture, there is strong cohesion between wetted particles; the resulting stickiness of the upgraded products can create significant materials handling issues unless processed in slurry form or at relatively low moisture levels. Langbeinite has been produced commercially from two locations, the Kalush and Stebnik regions in the Cartpathian Mountains of former Poland and now the Ukraine and from the Permian Basin in New Mexico (Garrett, 1996; Smith 1949). Current production is from two operators in the U.S., Mosaic and Intrepid Potash."

Jan 1, 2017

By J. Mark Richardson

The use of an integrated software package to simulate and optimize the performance of mineral processing circuits is illustrated by three examples. Each represents application of the software and associated techniques to optimization of an existing plant. In the first example, a South-western U. S. copper company employs the method to simulate and improve performance in crushing, screening and SAG milling. A second copper producer evaluates equipment changes and flowsheet alternatives in a closed-circuit ball mill-cyclone operation. A Southeastern U. S. aluminum refinery optimizes performance of a dry milling and classification circuit for production of carbon particles used in anode casting. Graphical and tabular data describe the circuits simulated and the results achieved in each example.

Jan 1, 1990

By Sotiris N. Kamenopoulos, Zach Agioutantis

Rare earth elements (REEs) are considered critical minerals for industrial and defense sectors. REEs are not as rare as the word “rare” portrays; yet, the exploitable and/or profitable deposits of REEs may be found only in certain geographical areas. The political and social conditions characterizing these areas may not always be in favor of mining operations. These conditions are imposing the need for extra consideration on the geopolitical constraints prior to any decision-making and before any mining project begins. This study assesses the risk related to mining projects for areas that feature REE deposits based on a geopolitical viewpoint. Probable ranking differences between the current assessment and a 2015 assessment are discussed. The comparative indicators used and the appraisal procedure applied in this comparison are based on a number of different geopolitical indicators. Several ranking changes occurred between 2015 and 2019.

By RICHARD A. THOMAS, Liming Yuan, Lihong Zhou, DAVOOD BAHRAMI

Mine ventilation simulation software has become an essential tool for the mining industry to design and manage mine ventilation operations. Building a well-calibrated mine ventilation network is time consuming, however, and requires great effort. In the last several decades, the mining industry has seen a steady increase in the use of air velocity sensors to monitor airflow and detect unexpected abnormal airflow in some key locations in underground mines. The present research work was carried out to explore the possibility and methodology of calibrating a ventilation network model using atmospheric monitoring system (AMS) data on a routine and ongoing basis.

Aug 1, 2022

By Gilbert Sauriol

The mining complex, which the Mines Gaspé division of Noranda Mines Limited has operated in Murdochville since 1954, includes open pit and underground mines, two mills, one leaching plant and a smelter. The under- ground mining uses predominantly a large scale room and pillar method, rooms 15 m wide, 30 m high and 300 m long being common. Ore production is effected by 4.5 m3 front-end loaders and 32-tonne trucks powered respectively by 225 and 325 kW diesels. Daily dust and gas readings show that air quality can be maintained at an acceptable level with much less ventilation than that normally specified. This paper emphasizes the point that air requirements should be based on Air Quality Standards, thus allowing an operation to benefit from favourable conditions or from improvements such as exhaust treatment, fuel alteration, etc.

Jan 1, 1983

By B. R. Waples

The first reaction in organizing a project of magnitude is that it's the same as smaller projects -- just bigger. This is not totally correct. The industry's record of completing big-money jobs on time and within budget is not outstanding. From a personal point of view, my question is: What is the project size at which controls are lost? Is it controls? Is it the number of pieces of equipment? Is it the number of decisions to be made? The slowness of communications? Or is it a combination of all of these? In working on multimillion-dollar jobs, the percentage of overrun seems to be lower or show an underrun when the following basics are followed: 1) Preplanning is intensified 2) Data gathering is complete 3) Approach is optimized 4) Planning is realistically scheduled 5) Changes are minimized 6) Decisions are expedited

Jan 1, 1982

By T. Diering

Gemcom PCBCTM is a software package which has been developed over the last 22 years for the planning and scheduling of block cave mines. This paper presents an update of the various research and development activities done to PCBC recently. It also provides an overview of the current capabilities of the software including tools for both feasibility type studies as well as tools for operating mines. PCBC is used extensively by prospective and operating block cave mines and some of the recent applications are described.

Jan 1, 2010

By Joel Lööw, Jan Johansson, Lena Abrahamsson

In this study, we try to illustrate what new technology can mean for the individual miner. We formulate the notion of Mining 4.0, where we attempt to create an image of how the future might look from a miner’s perspective and how mining companies might navigate their way to a future that works for all miners. 

By Norbert Patzelt, Hans Knecht, Wolfgang Baum

Future ore reserves of major gold producers in North America and elsewhere will consist of refractory gold ores. About 60 % of the current U.S. gold production is mined in Nevada. Several of the large gold operations in this state indicate that 40 to 90 % of their future ore feeds will contain refractory gold. To compound problems, average head grades for refractory U.S. gold ores have fallen from 8 - 9 g/mt to about 4 g/mt by 1991. In Latin America, 52 % of the gold operations will require milling for optimal recovery. Deeper reserves are, like in North America, refractory. Particularly in hard, (semi)refractory sulfide ores, many operations may experience substantial decreases of gold recov­ery. For example, Martins et al. (1991) report that at an Austra­lian mine, sulfide ore treatment led to 4 - 10 % lower gold reco­veries as the work index increased from 8 kWh/t to 14 kWh/t and the grind coarsened. Many refractory ores should actually be classified as semirefractory since a fine sulfide fracturing and liberation would make 80 - 90 % of the gold cyanide leachable. However, conventional comminution is often prohibitively expensive for these ore types.

Jan 1, 1995