Search Documents

By Faruk Oksuz, Cary Hirner, William A. Rochford

Grouting is a frequently utilized remedy in the planning and implementation of ground improvement and tunnel rehabilitation practice. The state-of-art grouting application used for Chicago’s McCook Reservoir project offers a unique alternative to the tunneling industry for pre-excavation grouting as well as tunnel rehabilitation, rescue and post-excavation ground improvements. The McCook Reservoir project included a computerized grouting control and data collection system for a precise and highly effective groundwater cutoff in fractured dolomites. By using balanced and stabilized grout mixes, the effective permeability of the rock mass was reduced over two orders of magnitude to less than 0.1 Lugeon by installing a double line grout curtain. The stable grout mix designs allowed high pressure and effective grouting at depths up to 125 m (410 ft).

Jan 1, 2005

By Jeremy Theys

The Sacramento Regional County Sanitation District (SRCSD) is improving the sewer system in the Natomas area of Sacramento, CA. The Upper Northwest Interceptor (UNWI) system is an ongoing series of tunnel pipeline projects that will provide sewer conveyance for all residents of northeast Sacramento County to the New Natomas Pumping Station, located North of downtown Sacramento, also in the city of Sacramento limits. The New Natomas Pumping Station then carries wastewater flowsto the Sacramento Regional Wastewater Treatment Plant in Elk Grove via the existing Lower Northwest Interceptor. The Joint Venture of Traylor Brothers, inc. and J.F. Shea (TSJV) were awarded the UNWI 1&2 project in late September, 2007. The planned 5.8 km (3.65 mile) construction route for UNWI 1&2 begins at the New Natomas Pump Station and runs north along the East Drainage Canal to the begin-ning of UNWI 3&4 at Bridgecross Drive. UNWI 1&2 includes approximately 5.8 km (19,240 feet) of 3.65 m (144 inch) inside diameter pipe using Earth Pressure Balance Tunneling Methods. The project also includes 16.76 m (55 feet) of 3.04 m (120-inch) diameter interceptor pipeline, twenty three access manholes spaced approximately 305 m (1,000 feet) apart along the alignment, a 2.13 m (84-inch) by 3.65 m (144-inch) transition structure, a 3.65 m (144-inch) by 3.04 m (120-inch) transition structure, and the connection of three existing sanitary sewer lines to the interceptor.

By G. Duncan, K. Winther, R. Ericsson

Distinct trends in grinding mill technology have emerged in recent years. In an effort to optimize overall mill performance for the needs of the End User, broad measures of logistical speed, process flexibility, operational risk, and overall costs now exert greater influence on the specification of grinding equipment. As a result, innovative alternatives to conventional grinding mill structures, supports, drives, feed, and discharge configurations are now being offered and selected with greater frequency. This paper investigates these trends in grinding mill technology, utilizing optimization and decision-theory techniques. In particular, the paper considers how specific advances in process design, product engineering, manufacturing techniques, and mining operations continue to relax technological constraints, enabling further mill innovation. In this context, a methodology is presented, illustrating how proper selection and specification of grinding mill components and configuration can target an optimization of the four End-User performance measures listed above.

Jan 1, 1999

By R. J. Pruett

The Georgia kaolin district is the world’s largest producer of kaolin. Georgia production tripled from 2.87 Mt (3.17 million st) in 1968 to8.35 Mt (9.2 million st) in 1998. Development of the Georgia kaolin industry can be traced to the identification of the mineral resource, the adoption of innovative process technologies and the creation of markets for kaolin. Georgia kaolin is an abundant and high-quality resource that shows a range of advantageous properties. Technical developments in wet processing, delamination and calcination allowed production of high-value products. The use of kaolin pigments in the paper industry provided a market that absorbed the rapid growth in kaolin production.

Jan 1, 2000

By Doug Harding

The Niagara Tunnel Project (NTP) is a 10.4 km (6.5 mi) long, 14.4 m (47.5 ft)bored tunnel that will run under the City of Niagara Falls from the Upper Niagara River to the Sir Adam Beck Power Station. The completed project will enhance the capacity of the Sir Adam Beck Power Station by adding 500 m3 (17,657 ft3) of water per second through the tunnel. The paper describes the project in which the world’s largest hard rock TBM at14.4 m (47.5 ft) in diameter is being used to excavate the tunnel. Features of the project include the use of a High Performance (HP) Main Beam TBM, state-of-the-art ground support and tunnel logistics systems. A continuous conveyor is used for muck transport from the TBM to the disposal area. The paper will also discuss the optimization of the TBM system as the tunnel advances through the varying geology. In June 2004 the Ontario Government announced that Ontario Power Generation(OPG) had been given approval to proceed with the third tunnel under the city of Niagara Falls—the first two tunnels were constructed in the 1950s using drill and blast techniques. The third tunnel, appropriately named The Niagara Tunnel Project (NTP), consists of a 10.4 km (6.5 mi) long TBM-bored, concrete-lined tunnel with a finished diameter of 12.5 m (41.1 ft). In August 2005, OPG announced the selection of Strabag AG of Austria, one of the largest construction companies in Europe, as the contractor to build the NTP Project at a price of CAN $600 million. In September 2005, Strabag A.G. selected The Robbins Company of Solon, Ohio to design, manufacture and deliver a new 14.4 m (47.5 ft) diameter High Performance state-of-the-art Main Beam Hard Rock TBM to be used in the excavation of the tunnel. In order to meet the aggressive construction schedule as requested by OPG/Strabag, the TBM needed to be supplied as “ready to bore” within a 12 month period after the contract was awarded to Robbins.

Jan 1, 2007

By Leroy O. Gieseke, John B. Begley

If the particles produced and transported in your plant are as chunky as rough crushed coal or as fine as cement, there are probably several conveying and elevating systems suitable for your operation. The problem is deciding which is most suitable in terms of space, energy cost, allowable product degradation, productivity, and angle of movement. Each conveying and elevating method should be fit to the products it can handle successfully, to desirable economics, and to suitability for the overall operating scheme. Matching along these lines will result in selection guides that should be useful for many years, although design evolution is expected for the materials handling equipment involved. There are several common bulk material handling devices for moving solids: belt conveyors, screw conveyors, bucket elevators, chain conveyors, and en-masse conveyors/ elevators. En-masse conveyor/elevator equipment is commonly compared and contrasted with the other devices. These comparisons often involve en-masse versus all others. En-masse has developed into a versatile technique because the machines can move materials horizontally, vertically, or in closed circuit. Such machines unload, elevate, store, reclaim, and distribute materials-all without ancillary equipment except for chutes and gates. Bulk material can be carried, as with a belt conveyor or bucket elevator; pushed, as with a flight or screw conveyor; bumped, as with a vibrating conveyor; blown, as with a pneumatic conveyor; fluidized, as with a dense phase pneumatic conveyor; or by applying internal forces to it to induce "en-masse" flow. Conveying en-masse is analogous to the flow of a fluid in an open channel, and elevating en-masse is analogous to the flow of fluid in a pipe. In the case of a fluid, flow is caused by a differential in pressure. With en-masse movement, flow results from resistance to shear induced by the movement of chain and flights.

Jan 12, 1980

A practical core-based method for estimating in situ stress was tested using 360° measurements of rock core diameter in a laboratory setting. In several mining districts across West Virginia, rock cores were recovered from exploration core holes and oriented using an acoustic televiewer (ATV) summary log. Measurements of diametral variation were performed at 0.1-foot depth intervals using a benchtop device comprised of a pair of diametrically opposed contact digital indicator gauges working in tandem. The diametral profiles were evaluated to determine strain direction and strain magnitude. Stress magnitudes were calculated when values for Young’s modulus, and Poisson’s ratio were available. Stress direction results are compared to other stress determination methods, including downhole overcores, drilling-induced fractures, and borehole breakouts. The testing and analytical methods used are similar to the diametrical core deformation analysis (DCDA) method (Ito, Funato, and Shono, 2012), but with a number of important improvements.

Jan 7, 2020

By J. Torma-Krajewski, C. Hipes

Many mining companies apply ergonomic principles, but it is done either informally and/or reactively. Examples of an informal approach include replacing worn equipment, such as seats, with models that have ergonomic features, or modifying tasks to eliminate safety hazards that will also reduce risk factor exposures that may result in musculoskeletal disorders (MSDs). A reactive approach is followed when modifying a task/equipment after an MSD occurs. Neither one of these approaches involves a systematic method of proactively applying ergonomic principles to actually prevent injuries or illnesses. This paper will discuss how Vulcan Materials Company applied ergonomic principles and the interventions implemented to reduce risk factor exposures.

Jan 1, 2007

By F. Bruey

The Factorial Model Experimenters are often interested in systems that are multi-factorial. A multi-factorial system is one whose output is believed or known to be dependent on the particular settings of several inputs, or factors. We can think of these factors as defining a space, with each point in this space corresponding to a particular set of factor settings. Experimenting can be thought of as exploring this space - finding out how the response of the system changes as factor settings are changed. There are several challenges in this exploration, among which are deciding what region to explore, designing an experiment that explores it most effectively, and describing the results of the exploration. This paper deals principally with the last of these; it shows how the factorial model can be used to describe how the response of the system changes as factor settings are changed. A strength of the factorial model is that it treats the factors as causes of change in the system's response and focuses on relations among these causes. In particular, the factorial model focuses on whether causes act independently on the system (in a sense to be explained below), or whether they interact. This is important because the experimenter generally seeks to control the system, and because control based on causes that act independently of other causes is relatively simple, whereas control based on causes that interact is more challenging. Also, mapping the space - finding out how the response of the system changes as factor settings are changed - will require less work if, during the exploration, it can be determined which of the causes act independently. For the sake of example, let us assume that the space we are exploring is three-dimensional, and that we have already defined, for each of the three factors, the range of interest. Let us consider all the ways in which the response of the system might depend on the settings of these three factors. In the simplest case, the response in this region does not depend on any of the factors. The response is constant throughout the space, at say, 80 units.

Jan 1, 2007

By E. F. Schnitzer, D. R. Haight, G. T. Krogman

The 1997 New Year’s Day Rogue River flood near Medford, Oregon, USA, entered historic channels, eroded a 150-foot-wide buffer, and captured an inactive gravel pond located within the channel migration zone. Channel redirection caused by pit captures threatened adjacent inactive gravel ponds. In response to this capture, a stakeholders group of concerned individuals and organizations was formed. This group ultimately developed a rehabilitation plan, which conformed to the Rogue River’s geomorphic trends. A two-dimensional model, FLO-2D, was used to evaluate channel splits, flood storage, backwater, and future conditions. Modeling results coupled with trend analysis were used to create a stable design where stream barbs, gravel redistribution, a channel outfall spillway, bendway weirs, bank reshaping, and revegetation were integrated into a single plan for a three-mile reach. The quick action by the stakeholders group averted further damage to the Rogue River system and surrounding environment. The project has preserved three miles of mainstem habitat, one mile of side channel habitat, and protected ten gravel ponds from pit capture.

Jan 1, 2006

By F. M. McEvoy, E. J. Steadman, R. Murfin

In England, the provision of aggregate is determined by the historical relationship between construction and aggregate consumption. This approach does not necessarily lead to sustainable decision-making and can be seen as being driven by political expediency, rather than reasonable environmental consideration. The introduction of the statutory requirement for Strategic Environmental Assessment (SEA) in the UK has provided the opportunity to examine this issue on a more rational basis. This paper provides a practical application of a SEA based approach, to the provision of aggregates at a regional level. The process, underpinned by relevant information on resources and environmental assets, suggests that alternative supply scenarios for aggregate provision are tested in a transparent, consistent manner with increased genuine stakeholder consultation. It supports a move away from "predict and provide" approaches to one where aggregates are sourced with the best balance of environmental costs and benefits.

Jan 1, 2005

By Zhenqi Cai

The ongoing Overpeck Valley Parallel Sewer Project of Bergen County Utilities Authority (BCUA), New Jersey, is a US $65 million CSO improvement program to meet a State DEP consent order by 2010. One major program component includes a total of 1.8 km (1.2 mile) long, 1,800 mm (72 in) diameter reinforced concrete pipe (RCP) installed by a Herrenknecht AVND1800AB MTBM. The alignment includes drives through 850 m (2,788 ft) of extremely soft glaciolacustrine varved clay, 980 m (3,214 ft) of loose to medium dense mixed soils containing silty sands, gravels, and boulders, and crosses under the New Jersey Turnpike, US Highway Route 46, and a CSX Railroad Intermodal Yard and a branch mainline. Two types of MTBM cutterheads are being used, one configured for the weak varved clay, and one for the mixed soil conditions. The MTBM is also equipped with a double-steering system consisting of a standard front steering joint and a second trailing steering joint to assist grade control should adequate steering not be achieved by the front primary steering in extremely weak soil conditions. This paper discusses the significant engineering aspects and challenges related to site settings, ground characterization, key MTBM features and performance, and required ground treatment.

By Maurice A. Ponti

The D.C. Water and Sewer Authority is implementing the Anacostia River Projects component of its Long-Term CSO Control Plan, including 21 kilometers of 3.7- to 7-meter-diameter CSO near-surface diversion storage/conveyance structures and flood relief, pressurized-face, soft ground tunnels at a maximum depth of 65 meters. This paper describes a project-specific soil grouping system that is primarily based on soil characteristics for tunneling derived from tests including Atterberg limits, grain size, swelling, mineralogy, triaxial, pressure meter, and consolidation, which differentiates the project from past area tunnel projects using descriptive systems based primarily on area geology.

By J. P. Brady

A major spontaneous combustion incident occurred in the sealed goaf of the SL3 Panel; Southland Colliery in 2003 resulting in the loss of a longwall and sealing of the mine. The most important issue for the new owners, Yancoal Australia Pty. Ltd, was to effectively manage the atmosphere in the fire affected sealed area. This atmosphere comprised of flammable gases, the products of combustion and excessive levels of oxygen due to pressure differentials across the panel isolation seals with a potential ignition source associated with the residual spontaneous combustion event. The challenges were met in the first instance by the erection of pressure balance chambers with limited success. The problem was not solved until the pressure chambers were pressurized using a Floxal Nitrogen Plant supplied by Air Liquide Australia. Given the success of this approach on a small scale, a higher capacity Air Liquide Floxal Unit was acquired to manage spontaneous combustion at the recommencement of longwall mining operations. This provided the ability to pressurize pressure chambers that were installed in the Maingate Seals behind the face of the adjacent Longwall Block effectively preventing the ingress of oxygen and permitting the goaf to self inert in a reasonable time period. This paper summarizes a new proactive method of mitigating the risks associated with active and sealed goaves. Proactive management of these areas using low flow nitrogen into pressure chambers to maintain a positive pressure has eliminated typical reliance in explosion proof or explosion resistance seals as the primary control.

Jan 1, 2009

By D. A. Lindsey

Gravel lithology affects the quality of aggregate because different rock types in gravel have different physical and chemical properties. The lithologic composition of alluvial gravel reflects the composition of its source terrane and the variable effects of weathering and transport on each rock type. This report discusses lithologic controls on aggregate quality in the mountain-front environment of the Colorado Front Range. Lithologic controls on aggregate quality of gravels were evaluated using pebble count data. Gravel lithology along the Front Range shows both temporal and regional variation. The principal variable in gravel lithology is quartz plus quartzite, of which quartzite is commonly more abundant. Large quantities of metaquartzite derived from the mountain front southwest of Boulder, Colo., were dispersed northeastward during deposition of the oldest Front Range gravels. Average quartz plus quartzite is greatest in the oldest gravels. Aggregate quality is probably enhanced by large quantities of quartzite. Abundant volcanic rocks in gravel may enhance aggregate quantity, but such occurrences are local in extent. Abundant sedimentary rocks in gravel, mainly sandstone near the mountain front, may decrease aggregate quality.

Jan 1, 2002

By A. B. Cecala

Enclosed cabs have been used for many years to isolate workers on mobile equipment in the mining industry for health and safety reasons. These enclosed cabs create a microenvironment for workers where they can be either more protected or more vulnerable to contaminants. Over the past decade, the National Institute for Occupational Safety and Health (NIOSH) has performed substantial research efforts to improve the air quality inside enclosed cabs of both underground and surface mobile mining equipment. In these efforts, NIOSH has partnered with mining companies, original equipment manufacturers (OEMs), and manufacturers of filtrations and pressurizations systems in a synergistic effort to reduce respirable dust and improve the air quality inside these enclosed cabs. Various field studies over this time have shown an array of results ranging from very minor to very significant reductions (protection factor: 3 ? 89) in respirable dust levels inside these enclosed cabs. In addition to and concurrent to the field work, NIOSH also performed a comprehensive laboratory study to evaluate all the factors involved in cab filtration and pressurization systems and identified those factors that were most significant for an effective system. From this comprehensive research effort, the key components for an effective filtration and pressurization system have been identified in an effort to provide the best air quality, thus minimizing the respirable dust exposure, to equipment operators inside of enclosed cabs of mobile mining equipment.

Feb 27, 2013

By Verya Nasri

This paper presents analysis of damages and rehabilitation design for three major French rail-way tunnels built in mid-19th century. The La Nerthe tunnel underwent ovalization deformation with excessive displacement at the springline, and pinching and bursting of the liner bricks at the crown due to tectonic residual stresses with very high lateral earth pressure. The Saint-Louis les Aygalades tunnel invert was subjected to undulatory deformation resulting in tracks misalignment, which was caused by non-homogeneity of mechanical and hydraulic properties of the ground. The Roches de Condrieu tunnel required widening to comply with the increase in dynamic envelope of trains due to their larger cross section and higher speed. The applied rehabilitation methods and constraints of work in these busy mainline railway tunnels have been discussed in detail.

Jan 1, 2008

By A. B. Cecala

Video technology coupled with datalogging exposure monitors have been used to evaluate worker exposure to different types of contaminants. However, previous application of this technology used a stationary video camera to record the worker?s activity while the worker wore some type of contaminant monitor. these techniques are not applicable to mobile workers in the mining industry because of their need to move around the operation while performing their duties. the Helmet-Cam is a recently developed exposure assessment tool that integrates a person-wearable video recorder with a datalogging dust monitor. these are worn by the miner in a backpack, safety belt or safety vest to identify areas or job tasks of elevated exposure. After a miner performs his or her job while wearing the unit, the video and dust exposure data filesare downloaded to a computer and then merged together through a NIOSH-developed computer software program called enhanced Video Analysis of Dust exposure (eVADe). by providing synchronized playback of the merged video footage and dust exposure data, the eVADe software allows for the assessment and identificationof key work areas and processes, as well as work tasks that significantlyimpact a worker?s personal respirable dust exposure. the Helmet-Cam technology has been tested at a number of metal/nonmetal mining operations and has proven to be a valuable assessment tool. mining companies wishing to use this technique can purchase a commercially available video camera and an instantaneous dust monitor to obtain the necessary data, and the NIOSH-developed eVADe software will be available for download at no cost on the NIOSH website.

Sep 1, 2013

By S. Garcia, J. Gebhardt, D. McBride, A. Hernandez, A. Esplín, M. Cross

The Minera Yanacocha operation consists of several heaps interconnected with ponds and gold recovery plants and presents various operating challenges. A comprehensive process model has been developed in order to better understand the effects of certain operating parameters and inventory issues. An integral component of the process water/mass balance is a model of each heap that describes heap behavior based on the individual characteristics of the heap. The heap models are linked to a mass balancing program in order to track flows and concentrations throughout the circuit. A case study of the process heap model is presented for the La Quinua heap, including results for the normal base line operation and several operational problems such as loss of solution flow to the heap (i.e., pump failure), increased flow to a section of the heap (i.e., pond volume control), effect of significant rain events, and impact of a change in material properties (i.e., change in ore type). The impact on heap operating efficiency is discussed with regard to effects on recovery and gold solution grades.

Jan 1, 2007

By S. E. Phillipson, P. L. Tyrna

Lineament analysis, a remote sensing application for geological structures, has been criticized for reliance on subjective interpretations. The Mine Safety & Health Administration’s Roof Control Division performs lineament analyses with a technique that removes much subjectivity. Study areas are viewed on satellite images with software that allows examination under artificial sun azimuths and elevations. Extraneous lineaments are removed through successive steps of superposition, resulting in selection of the most robust linear features. Field investigations revealed a strong coincidence of joint and fault zones that were parallel with projected lineaments. The Roof Control Division’s successful identification of lineaments associated with roof falls and highwall failures has prompted some mine managers to incorporate lineament analysis as a mine-planning tool. The identification of potentially hazardous ground conditions will allow mine operators to obviate safety concerns that might otherwise adversely affect miner health and safety.

Jan 1, 2002