Search Documents

By B. Mishra

This paper presents a rock mechanics investigation of the time-dependent behavior of the rock immediately surrounding the excavation in a hypothetical one-entry coal mine based on the geology of the Illinois coalfields Research in the area of time-dependency is almost nonexistent and, therefore, this research was performed to make inroads into this neglected research area. Numerical analysis of a typical one-entry coal mine in an Illinois basin was performed using the commercial finite difference program FLAC3D. The immediate roof of the coal entry was assumed to be a shale formation. Shale in other formations has shown a tendency to creep with time. Therefore, in this study the authors modeled the shale in the roof using time-dependent characteristics. The input properties were taken from laboratory creep tests performed on shale. Model runs were performed at different stages, mimicking the progressive excavation of the entry. The model results showed that stresses in the roof attained the limit of yielding. Using Mohr-Coulomb failure criteria, potential zones of failure were also predicted. The results showed that the current computational capacities are sufficient to explore this previously uncharted territory of ground control.

Mar 1, 2014

By Leonard B. Rothfeld

For many years, pulverized coal (PC) boilers in utility power plants have been the dominant market for domestic coal. Today, two new coal utilization technologies challenge the PC boiler's dominance. Atmospheric fluidized bed combustion (AFBC) and "coal gasification/combined cycle" (GCC) stand on the verge of commercial demonstration in the utility environment at a scale of 100 MW. Developed over the past decade, these technologies respond to the demands for cleaner ways to burn coal and for more flexibility in fuel supply. In the near term, these are the "clean coal" technologies most likely to have a significant impact, because they are ready for commercial application. As for environmental acceptability, consider that just a few years ago one of the environmental slogans was "no coal in California." Indeed, the only large quantities of coal above ground in California at that time were in transit on the way to Asia. Today, thanks to new technology, we can point to two operational coal-burning plants in California and one in the works: * Cool Water GCC demonstration plant (100 MW) * California Portland Cement AFBC commercial cogeneration, near Riverside (190 000 lb/hr steam) * Energy Factors AFBC commercial cogeneration at Stockton, to be operational 1988 (44 MW)

Jan 1, 1987

By M. Schlegel, J. A. Villa Mena, R. E. Vivas

ArcelorMittal, headquartered in Luxembourg, is one of the world’s largest steel and mining companies. It supplies steel to industries such as automotive, construction, and energy, with a strong emphasis on sustainability and innovation. The company employs about 125,000 people and, in 2024, produced 42.4 million tons of iron ore and 57.9 million tons of crude steel across 15 countries. Its mining operations span Canada, the United States, Mexico, Brazil, Ukraine, Bosnia and Herzegovina, Kazakhstan, and Liberia, focusing on iron ore and coal extraction to support steel production. This study examines Peña Colorada, one of Mexico’s largest iron ore mines (a joint venture by ArcelorMittal and Ternium). Facing declining ore grades, Peña Colorada adopted Hexagon solutions to uncover and capture project value. A comparison of two Life of Mine (LOM) plans from 2012 and 2016 (before and after implementing Hexagon solutions) shows that between 2019 and 2023, Peña Colorada reduced actual waste by 26% (compared to 2012 LOM) and 19% (compared to 2016 LOM). LOM Plans are generated yearly, and each time, opportunities for reducing mining waste were identified, evaluated and implemented. The key driver was schedule optimization using Hexagon MinePlan Schedule Optimizer (MPSO). This reduction means less waste transported to disposal sites, resulting in fewer hauling equipment operating hours, lower fuel consumption, and reduced carbon emissions.

Feb 22, 2026

By Duluth Engineers' Club, Engineers' Club of Northern Minnesota

"Prospecting and Exploration. Since the Lake Superior ores occur in pockets or distinct bodies and vary much as to character and location, the actual mining of the ores is preceded by much work of an exploratory character. This work includes prospecting and exploration.Prospecting is the term generally applied to the quest for surface indications of ore, or the conditions which would warrant the expectation of finding ore in the vicinity. It includes such 'operations as geological examination, dip needle work, shallow test-pitting, and trenching. The ore bodies of the Mesabi Range are non-magnetic, and dip needle prospecting is therefore valueless. On the Cuyuna range, however, magnetic attraction as evidenced by the dip needle has been extensively employed as a guide to the location of ore deposits; in other localities it has found limited application.Drill Exploration. After the presence of an ore deposit is known or suspected, resort is generally had to exploration by means of diamond or churn drills. On the old ranges geological conditions generally make this manner of ascertaining the exact limits of an ore deposit impracticable; so, if two or three adjacent drill holes develop considerable depths of ore, the sinking of a shaft for underground exploration, development and mining is generally considered warranted. On the Mesabi Range, however, the flat-lying and comparatively shallow characteristics of the ore formation warrant much more extensive drill explorations. On this range, then, an ore body 'is almost invariably followed· out with the drills, and its limits are determined to the point where the complete plan of development can be worked out in advance of actual mining operations"

Jan 1, 1920

By Roger Storry, Arnaud Hochart, David Harris, Olivier Martin

"INTRODUCTIONThe Port of Miami Tunnel (POMT), designed and constructed by Bouygues Civil Works Florida between 2009 and 2014, was a Public Private Partnership between the Miami Access Tunnel Concessionaire, Florida Department of Transport, Miami-Dade County and the City of Miami. The project comprises dual 11.3m internal diameter, 1.27km long, twin lane road tunnels running between Watson and Dodge islands under the main shipping channel in Biscayne Bay. Five cross passages (CPs), spaced at 200m centre to centre, provide emergency access between the two tunnels, as shown in Figure 1.The CPs were constructed by open-face excavation methods but the particular geological conditions at the project site (loose and variable carbonate sedimentary strata with very high permeability) required specific ground treatment solutions to provide safe excavation conditions and to ensure the long term serviceability of the permanent works construction. Where access allowed, ground treatment was performed from the ground surface using deep-mixing techniques; however, at two locations (CP2 and CP3) surface access was restricted and ground treatment by freezing, performed from the tunnels, was required. The CPs are 12.3m long with an excavation diameter of 5.8m and are located up to 30m below the water table partly or wholly within the Key Largo limestone (termed Layer S7 in the ground model). Layer S7 is a coralline limestone having a metastable honeycomb structure and high variable porosity. At CP2 the upper portion of the excavation was within the overlying Anastasia Formation limestone (Layer S6), comprising a highly permeable coquina. The geological profile along the project is shown in Figure 2.This paper presents aspects of the freeze design and the risk mitigation necessary to successfully achieve the construction of the CPs in the unique geological conditions."

Jan 1, 2016

By David L. Brostrom, William C. Brice, Perry A. Canton

The business of mineral exploration and development has become much more than simply a problem of locating orebodies and designing mines. Favorable economic analysis of mining and processing feasibility is no longer sufficient to justify the development of a mine. New laws, enacted by virtually every level of government, require comprehensive land use planning, environmental analysis, mineland reclamation, mine safety studies, and many other considerations. This profusion of new laws says in effect, that the mining company is no longer responsible only to its stockholders. Mineral development today can be compared to a partnership. As in all partnerships, the risks and liabilities as well as the benefits are held jointly by all the participants. In addition to the mining operator, this partnership consists of the public, through its many levels of government, interest groups, and individual citizens. Therefore, you'd better know your partner very well - his responsibilities and capabilities. Mining is considered a high risk venture. The risk on the part of the operator and the lending institutions has long been recognized. The risk that the public and its government take in these mining ventures has now been recognized also. The people and their government have learned that they inherit, through abandonment or forfeiture, the mistakes and problems of individuals and companies regarding these natural resources. In looking through the "Mining Engineering Handbook" recently published by the Society of Mining Engineers, I noted that in their discussion of liability for excavations, the authors quoted from the book of Exodus, 20th chap., where Moses said to his people: "When a man leaves a pit open, or when a man digs a pit and does not cover it, and an ox or an ass falls into it, the owner of the pit shall make it good; he shall give money to its owner, and the dead beast

Jan 1, 1974

By Stanley J. Gasior

Most bituminous coal mined near Eastern industrial areas requiring high Btu pipeline gas is caking and therefore unsuitable for fixed-bed pressure gasification by present techniques. If the caking property of such coal can be destroyed the resulting fuel can be gasified in a fixed bed at pressure with steam and oxygen as a preliminary step in making a high-Btu gas. To find a practical way to convert strongly caking coals of granular or small lump size to noncaking fuel was the object of this study. In previous work strongly caking coals of 1/8- to 1-1/2-inch size was converted to a noncaking coal char by treatment in a static bed in about 3 hours [1/]and coal of 18-100 Tyler mesh in a fluidized bed in about 5 minutes.[2/] An inert gas such as `steam, nitrogen, carbon dioxide, or a mixture of all three with a small amount of oxygen was used in both studies. In our work a strongly caking bituminous coal from the Pittsburgh seam of 4-8 Tyler mesh size was converted to a-noncaking form in free-fall in about 2 seconds by dropping it through a countercurrent flow of steam containing 4 to 7 percent oxygen at 1,150°-1,200° F and 300 psig. This method should also be applicable to smaller-sized material.

Jan 1, 1965

By H. Sevim

A new method of designing haulage systems, consisting of belt conveyors and hoists for underground mines is discussed in this paper. Efficient and economic design of such systems will prevent operational bottlenecks and provide savings. The developed model uses a heuristic algorithm to optimize the design parameters and to select the proper equipment specifications. It is a probabilistic model because it considers the probabilistic aspects of face operations. It is versatile because it can accommodate belt conveyor networks of any configuration and hoisting systems that can be either drum or friction hoists for single or multiple-level operations. The model also has the option to internally determine the required capacities of the bunker(s) and shaft- bottom bin. The objective of the optimization process is to minimize the "expected cost per ton of ore hauled" from the working faces to the surface. A numerical example is included to illustrate the capabilities of the model.

Jan 1, 1987

By Sandeep Kumar Jeripotula, Govinda Raj Mandela, Aruna Manglapady

The main aim of this work is to evaluate whole-body vibration (WBV) of dozer operators based on three sitting postures (i.e., with 15° lean forward inclination posture, vertically erect posture with no inclination, and with 15° lean backward inclination posture) in Indian surface coal mines. A seat pad tri-axial accelerometer was used to collect WBV data from six dozer operators for three different sitting postures. Results showed that except for Dozer-1, 2, 4, and 5 operators during lean forward sitting posture and Dozer-4 operator during vertical erected posture, no other dozer operators have exceeded an exposure limit value (ELV) of 1.15 m/s2 in any of the considered sitting postures. Similarly, the vibration dose value (VDV) based on exposure action value (EAV) of 9.1 m/s1.75 has surpassed for all the dozers. But no dozer operator has exceeded an exposure limit value of 21 m/s1.75. The outcome of the study infers that based on “above health guidance caution zone (HGCZ)” for daily vibration exposure, i.e., A(8) measurements, for the operator sitting in lean backward postures the vibration amplification was reduced by 32.89% less compared with lean forward posture and 16.23% less when compared with vertically erected posture. Similarly, based on VDV(8), the exposure to vibration for the lean backward posture was reduced by 33.34% when compared with lean forward posture and 17.11% less when compared with vertically erected posture. Based on the above observation, it is concluded that lean back inclination with a trunk flexion of 15° is a favorable sitting posture, as it exposes the dozer operators to minimum vibration.

By Lewis J. Patterson

In the period of time allotted to this paper, an attempt will be made to cover a great deal of territory, figuratively speaking, as far as our experience with ammonium nitrate is concerned. In giving this subject the "broad-brush" treatment, it will be necessary to generalize on the major points which at the same time will permit me to avoid, to a great extent, any involvement in the purely technical and theoretical aspects of blasting. The practice of theorizing before a new idea is tried has practically been discontinued in our organization simply because experience has shown that, almost without exception, theories have fallen aside as some new development takes its place. In regard to blasting, logic and experience seem to have little place in this phase of quarry operations. As the use of low cost blasting agents was introduced in our operating practice, a man who had no previous experience in the field of blasting but with sound knowledge in safety procedures was given the responsibility of supervising the drilling and blasting operations. A total lack of experience is not ordinarily recommended as a prerequisite to assuming the responsibilities of a supervisory position. However, in this case it was obviously a wise decision because there were no pre-conceived ideas as to what techniques would or would not be successful.

Jan 1, 1958

By Richard C. Corson

The objective of blending materials in a bedding pile is to reduce the variation in successive samples taken from the materials to be blended. In designing a bedding and reclaiming operation, several mechanisms are available to effect the reduction of variability, or increase in homogeneity, of the materials. These mechanisms can act before stacking, in the stacking process, in reclaiming and after reclaiming. In evaluating alternative methods of stacking and reclaiming, the potential user must judge each method on the basis of certain criteria; the capital cost of the equipment, the allowable absolute variability of the reclaimed product and the effectiveness of blending. Several stacking and reclaiming methods have been tested using a computer simulation. Based on the results of this program, factors were developed to describe the effectiveness of blending for chevron stacking of discrete materials and preblended materials, bucket wheel reclaiming and drum reclaiming. From these factors, the total effectiveness of a combined stacking and reclaiming system can be determined.

Jan 1, 1985

By A. G. Mayton, D. H. Ambrose, C. C. Jobes, N. K. Kittusamy

In a systematic study, the National Institute for Occupational Safety and Health (NIOSH) evaluated seat designs in low- and mid-seam shuttle cars during production operations at two underground coal mines in southern West Virginia. The purpose was to support, with additional data, earlier findings that NIOSH ergonomic seat designs (featuring viscoelastic foam padding and lower-back support) may help reduce health risks to operators of coal mine shuttle cars. Eight shuttle car operators evaluated seven seat designs (one already in use in each vehicle and five NIOSH designs) relative to perceived and measured whole-body vibration (WBV) exposure (including vehicle jarring/jolting) and discomfort. Operators’ perceptions using a visual analog scale (VAS) and questionnaire ratings were compared with International Standards Organization (ISO) 2631-1:1985 fatigue-decreased proficiency (FDP) limits and measured WBV levels on low- and mid-seam shuttle cars. Objective and subjective data results indicated that NIOSH seat designs (with added adjustability, lower-back support and improved seat padding) performed better to reduce vehicle jarring/jolting levels and that shuttle car operators favored them over existing seat designs. The NIOSH low- and mid-seam shuttle car seats showed 45 to 77 percent better performance in FDP and 9 to 60 percent better performance overall in operators’ ratings. Considering the VAS results for low- and mid-seam shuttle cars under no-load conditions, operators rated the level of jarring/jolting 18 to 89 percent lower with the NIOSH seats. Reductions in measured vehicle jarring/jolting were 19 to 46 percent for the three-directional vector sum accelerations relative to the existing seats on the low- and mid-seam shuttle cars. Questionnaire responses indicated that operators for both shuttle car models rated NIOSH seat designs as more comfortable overall. Vehicle operators most frequently suggested adding armrests to improve the seats on the mid-seam shuttle car. A suggested improvement for the low-seam shuttle car was to make the seat a better fit for the operator compartment, which would enhance clearance between the operator and vehicle controls and allow for better seat adjustment and operator visibility.

Jan 1, 2009

By Jan M. Mutmansky

Since 1973 when the first edition of the SME Mining Engineering Handbook was published, many significant changes have occurred in the US mining industry. The industry went through a fairly prosperous period immediately after 1973, but then many economic pressures came to bear on mining companies, particularly in the metal and coal branches of the industry. These pressures changed both the mining methods used and the general economics of the mining methods. As a result, the industry today is different in many ways titan it was in 1973. A general summary of some of the more important changes that have come about will be provided here as well as some assessment of the effects of these changes on the choices of mining methods. In the metal mining industry, the most significant trends were increased surface mining, the use of larger and more efficient equipment, and increased technology and automation. The primary impetus for these changes was unprecedented competition from foreign producers. In many cases, this competition came about because of the nationalization of foreign mines and the tendency for these mines to become a source of foreign exchange. Under these circumstances, the mines could be operated even though they were not profitable. As a result, domestic

Jan 1, 2008

By D. C. Yang

A practical and economical flowsheet has been developed and demonstrated by integrating the packed column flotation with the GranuFlow process for fine coal recovery. Orimulsion, which was used as an additive, served a dual purpose: first in the flotation and second in the dewatering and granulation steps. The test results on the coal preparation effluent sample show that Orimulsion is flexible and compatible with fuel oil and various frothers used in the packed column. Clean coal with ash contents of 3.0, 3.7, 4.3 and 5.1% were produced from a head sample of 33% ash at combustible matter recoveries of 72.4, 81.1, 87.5, and 89.2%, respectively. Other advantages include high throughput, low moisture, improved handleability, and reduced dustiness of the dewatered coal, thus providing a very significant economic Incentive for the integrated process.

Jan 1, 1998

By C. L. Sainsbury

For 10 years, the author has been engaged in a program of geologic mapping of the Seward Peninsula, Alaska, for the U.S. Geological Survey. Initially, two 1:63,360-scale quadrangles were napped by traditional methods of traverses by foot and by tracked vehicle, supplemented by reconnaissance from a light aircraft owned and piloted by the author. Five summers were required to map those two quadrangles, which lie north of the tree lice in typical Arctic climate. In 1967, the project was reoriented toward the reconnaissance capping of four 1:250,000-scale quadrangles, with helicopter support to be used for cart of each of four summers amounting to about 45 hours time per support year. The light aircraft was use-,' to support the field operations. Over the year,, the aircraft was used in progressively more geologic tasks, culminating in 1970 with a successful field test of rudimentary devices made to collect soil, rock, and sediment samples while the aircraft remained airborne. Additionally, an attempt was made j- 1970 to prepare reconnaissance geologic maps entirely by the use of the light aircraft combined with foot traverses [fr??], the landed aircraft. Several such maps, prepared at the rate of about one 1:63,360-scale quadrangle per day, were checked from a helicopter by an impartial observer end were found to be sufficiently accurate for reconnaissance mapping when reduced to 1:250.000 scale.

Jan 1, 1971

By R. Kramer, A. Habibi

A ventilation survey was conducted in an underground longwall trona mine. The mine is relatively shallow and categorized as a gassy mine. The ventilation system includes three intake and six exhaust shafts, and three surface axial fans ventilate the mine in a blowing configuration. Airflow quantity, pressure losses and air psychrometric characteristics were quantified, and the influence of moving cages and skips in the shaft examined. The benefits of utilizing high-accuracy digital pressure transducers and advanced psychrometers were seen when undertaking a “leapfrogging” survey to gather data needed to build a computer ventilation model. Two underground booster fans with VFDs are idle but available at the mine. The ventilation model was used to determine the optimal booster fan locations to decrease operating cost by reducing the load carried by the main fans. A leakage study was conducted to evaluate the effects on the system of additional pressure from a booster fan. The study finally prepares a future ventilation model for the next 15 years of mine operation and investigates the effect of proposed scenarios.

Jan 1, 2014

By Curt Swanson, David C. Mathy, Dru R. Nielson, Kent VonAspern

In 1997, Central Contra Costa Sanitary District undertook the design of the Martinez East Side Trunk Sewer Improvements Project. Microtunneling was specified for approximately 1,035 meters (3,400 feet) of 600-mm (24-inch)diameter pipeline to be installed through estuarine soil deposits (San Francisco Bay Mud) and alluvium beneath the congested city streets of downtown Martinez, California. Directional drilling was specified for approximately 275 meters (900feet) of 200-mm (8-inch) diameter pipeline in four separate segments to be drilled through bedrock within narrow utility easements between residential properties. This paper presents a case history for the design and construction of themicrotunneling and directional drilling aspects of the project.

Jan 1, 1999

By Robert Stefanko

The Federal Coal Mine Health and Safety Act of 1969 had far reaching effects upon many aspects of mining, ventilation being no exception. In this paper, good ventilation procedures are briefly reviewed, and attention is focused on the changes brought about by the new Act. By way of illustration the ventilation system for a typical Pittsburgh Block system is developed and the requirements of the fan determined. This is then solved by an available computer program, and the application is evaluated. Figure 1 represents a projected system for a coal property 1 by 3 miles in plan at a depth of 1000 feet with a coal thickness of 6 feet and desired daily tonnage of approximately 7200 tons on a two-shift basis. Only one half of the mine is shown (north area) with a mirror image mining arrangement to be developed concurrently for the south area. Six working units are projected, three in each area, one on pillar extraction, another developing panel entries and a third on main entry development. A two-split system is used for each working section so that the continuous miner and bolting crews each have a separate split of air, and no equipment need pass through a line brattice. The old requirement of 6000 cfm at the last open crosscut has been increased to 9000 cfm, and for the first time a minimum quantity (3000 cfm) is stipulated at the face thus requiring either line brattice or an auxiliary fan. With the respirable dust requirement limited to 3 mg/m3, the use of a blower system is precluded and exhaust systems are virtually the only choice. Maintaining the line brattice within 10 feet of the working face at all times as required by the new law has a definite effect on the mining cycle and is most difficult at best. In the highly gaseous Pittsburgh seam located in south-western Pennsylvania and northern West Virginia quantities of 20,000 cfm per split are not uncommon to maintain the methane percentage below the required l%

Jan 1, 1972

By Richard S. Della Valle

Sandstone and shale samples from the Morrison (Late Jurassic) and Dakota formations (Cretaceous) from northwestern New Mexico have been analyzed for the major elements Na, K, Fe and the trace elements Sc, Cr, Co, Rb, Sb, Cs, Ba, Hf, Ta, Th, iJ and the rare earth elements (REE) in whole rock and clay sized fractions by instrumental and delayed neutron activation analysis. The clay sized fraction clearly shows enrichment patterns and halo effects ; whereas, the whole rock fraction does not. Important elemental dispersion halos associated with uranium in sedimentary environments include the REE, Hf, and Sb. The distribution of these halos are due to a combination of complexation, chelation and the orignal paleoenvironments.

Jan 1, 1984

By Roger D. Sharpe

Oklahoma contains extensive resources of high-purity gypsum that were deposited in the Anadarko and Hollis basins during Permian time. The gypsum resources and reserves are estimated to be about 48 billion short tons and a; located in the western portion of the state. Oklahoma is the largest producer of gypsum products in the United States. The Blaine Formation and the Cloud Chief Gypsum contain several beds of minable thickness. Four stratigraphic units in the Blaine Formation are quarried in Oklahoma. The Shimer, Nescatunga, and Medicine Lodge Members are quarried in northwest Oklahoma. The Van Vacter Member, consisting of three gypsum beds, is quarried in southwest Oklahoma. The Cloud Chief Gypsum is quarried in the west-central part of the state. The gently dipping gypsum in the Blaine Formation generally crops out along low escarpments and is covered in the downdip direction by increasing overburden, consisting of sand, shale, and/or dolomite. Anhydrite occurs in the downdip direction under the thicker overburden. The Cloud Chief Gypsum crops out as hills, which are eroded remnants of a more widespread, massive sulfate unit. All of the gypsum produced in Oklahoma is extracted using quarrying methods. A variety of products are made from gypsum quarried in Oklahoma. The products are manufactured from uncalcined, calcined, and deadburned gypsum. Products vary from raw, ground gypsum used for agriculture, to high-value-added industrial plasters, cements, and fillers produced from calcined gypsum. A sampling of the many products manufactured from Oklahoma gypsumincludes: (1) agricultural-soil amendment; carrier for insecticides, pesticides, and herbicides; calcium supplement in animal feeds; (2) gypsum wallboard-common, fire-resistant, and water-resistant varieties; (3) industrialgypsum plasters-art and casting, pottery and ceramic, molding and tooling, crayons, wall patching; (4) industrial gypsum cements-oil-well cement, high-strength statuary, high-strength tooling, fiber-reinforced architectural, road and bridge repair; (5) food and pharmaceutical-filler and binder in aspirin and other medicines, yeast activator in brewing of beer, moisture absorbent in bread and pizza dough; and (6)portland-cement retarder-ground with clinker to control setting time.

Jan 1, 1999