Search Documents

By D. McElhinney, J. Winfield, G. Buchan, B. Slaker, A. Iannacchione, T. Minoski, G. Rashed, M. Van Dyke, M. Murphy

"The National Institute for Occupational Safety and Health (NIOSH) has previously established pillar design guidelines for the underground stone mining industry. These guidelines were created from an empirical database of pillar observations and were largely drawn from shallow, flat-lying mining operations. Current trends forecast a great amount of underground stone mines developing under deeper cover, higher seam dips, and more frequent multiple-seam mining configurations than in the past. The complex loading conditions and limited experience in these environments presents a substantial increased risk of ground failure. To investigate these loading conditions, NIOSH has installed a pillar and roof monitoring system at an underground limestone mine in central Pennsylvania. The mine is operating in a seam with dips ranging from 13 to 18 degrees and overburdens ranging from 275 m (900 ft) to 425 m (1,400 ft). Instrumentation installed in an undeveloped pillar and in surrounding strata is currently measuring pillar and roof behavior in response to stress redistribution during excavation. Laser scans are being used to measure ground displacement and changes in conditions associated with local mining conditions and significant geological features. Initial stress measurements show a gradual increase in stress in response to mining, and stress changes that correspond with blasts. The seismic system is operational, with calibration events signaling on each of the 18 sensors. INTRODUCTION Improving mine-wide ground control stability can help reduce the potential for catastrophic failure of underground structures. The National Institute for Occupational Safety and Health (NIOSH) has conducted prior research in stone pillar design and has established fundamental pillar design guidelines for the underground stone mining industry, which resulted in the development of the S-Pillar program (Esterhuizen et al., 2011; Esterhuizen and Murphy, 2015). The data that constitute the S-Pillar program were derived from past mining experience that was almost exclusively drawn from shallow, flat-lying, single-level mining operations1. Stakeholder interactions with NIOSH researchers have indicated that increased numbers of underground stone operations are expected to mine under significantly deeper cover, with greater seam dips, and under multi-level operating conditions (Slaker and Murphy, 2016). The complex loading conditions and limited experience in these challenging environments present a substantial increased risk of ground failure. Inadequate pillar design in these new and challenging environments could result in catastrophic wide-area pillar collapses and an increased safety burden to miners working in the U.S. limestone mining industry. To develop design guidelines and prevent inadequate pillar designs for these challenging environments, NIOSH is currently conducting detailed pillar response investigations at case-study mine sites operating in challenging environments."

Jan 1, 2018

By S. Natansohn

A prevalent technique for the recovery of silver from wastes generated in silver-tungsten electrical contact fabrication is electrowinning. Such scrap is placed in a permeable plastic basket which constitutes the anode compartment and this basket is suspended in a larger cell in which the cathode is mounted. A silver nitrate solution is used as the electrolyte and, upon application of an electric field, the silver migrates to the cathode where it deposits out. At times, there is tungsten migration to the cathode compartment and consequent co-deposition with the silver. This W contamination, which may amount to several thousand ppm, necessitates additional purification of the deposited Ag and its removal would therefore be advantageous. The elimination of the W impurity would also extend the operating period of the cell with corresponding increase in the Ag output and savings in labor costs.

Jan 1, 1982

By A. Mull, J. Weyer, J. Brune

"The “Reiche Zeche” mine in Freiberg, Germany, a 600-year-old lead-zinc-silver mine with extensive open mine workings, experiences severe ventilation losses due to leakage. Much air leaks into abandoned workings, decreasing the airflow available to active working areas. Usually, this leakage occurs in remote areas that lack transportation infrastructure like roadways or rail, making it difficult to haul construction materials to the sites to erect passive ventilation controls such as stoppings, regulators and seals. Transportation distances make it impractical to hand carry traditional construction materials, such as bricks and concrete. Alternative materials, such as brattice, foaming polymers, concrete canvas, and some innovative ventilation control designs have been investigated for this purpose. The suitability of the materials investigated depends on many factors including the pressure it can withstand, the ease of transportation, and workability. Impacts of mine water must be considered, as the Reiche Zeche is below drainage and experiences significant inflow of water. Researchers must consider the effects water inundation as well as how the stopping construction material reacts to being exposed to acidic mine water. INTRODUCTION Problem Statement Mining in the area around Freiberg, Germany began in the 12th century. The mine is used for research, mining engineering education, tourism and air conditioning for a local hospital. The first records of mining in the Reiche Zeche are from around 1384. Due to the strength and competency of the host rock, many of the oldest workings still stand and remain open today, although they may not be accessible. Reiche Zeche also connects to several other, closed mines in the area that are largely unmapped. This allows air to leak into neighboring mines, reducing the air available to ventilate to the working areas of Reiche Zeche. In order to improve ventilation efficiency, it is necessary to control the ventilation and reduce leakage by constructing seals, stoppings and regulators. A challenge with building traditional seals and stoppings in the Reiche Zeche is that the old workings lack transportation pathways or rails. Also, the lack of compressed air, water or electricity makes it difficult to operate power tools and drills. This means that construction materials must be hand carried – some over distances of several kilometers. Figure 1 shows a typical drift in the Reiche Zeche. Researchers investigated using lighter, more easily transportable materials including concrete canvas, expanding polyurethane and polyurea foams, and brattice. The applicability and utility of these materials depends on a variety of factors including the ventilation air pressure, chemical resistance to acidic and mineral-laden mine waters, ease of transport, and ease of construction. Stoppings and seals must be substantially constructed so that they remain tight and do not require maintenance. It is also important to consider the toxicity of the construction materials in case of a mine fire."

Jan 1, 2016

By R. Raby

During the 1980 decade, the rapid price increase for flake graphite has generated a high degree of interest for the discovery and the development of alternate occidental sources of supply in response to fluctuations in quality and availability from current producers. Alike many industrial minerals, graphite draws its complexity not only from its mineralogy and unique properties but also from the very large spectrum of industrial applications each calling for specific quality criterion. As new high technology uses are being developed, more rigid specifications will apply. Discovered during the latter part of 1988 by Mazarin inc., some 30 Km South of Fermont near the Quebec-Labrador border, the Lac Knife deposit was quickly identified as one of the world major long term alternate source of stable supply for this mineral. This paper also reviews the status of the project development as of late 1991, while updating previous papers published by Industrial Minerals1990 and Mining Magazine 1990.

Jan 1, 1992

By Mark Colwell

This paper summarizes the results of a research project whose goal was to provide the Australian coal industry with a longwall installation roadway (faceroad) design methodology that could be utilized by suitably qualified colliery personnel. This goal was achieved in 2012 and the design methodology (and software package) is referred to as Analysis and Design of Faceroad Roof Support (ADFRS). The intended benefits to underground operations, in the provision of this information and resource, are a safer and more productive workplace.

By N. J. Keys

This paper concerns the development and application of a high throughput multi-stream photometric sorting machine developed for the South African gold mines. It is now believed that this sorter and its progeny may be found suitable for a large proportion of all possible sorting applications. A laser light source and sensitive photomultiplier are employed in a scanning system to detect light reflected from the surfaces of rocks passing through the sorting zone. Electronic circuitry then analyzes the photomultiplier signal, which represents the varying intensity of the reflected light, and produces control signals to actuate the appropriate valves of an array of air blast rejection devices to remove from the feed certain particles selected by the analyzing process. Typical throughput per machine ranges from 50 tons/hour for a-2 ½? + 1 ¼? feed to 200 tons/hour for -6" +2 ¾ " material.

Jan 1, 1974

By D. E. Munson

The Waste Isolation Pilot Plant (WIPP) Project was established in 1975 by the Department of Energy (DOE) under Public Law 193 to develop the necessary technology for safe disposal of radioactive wastes from the defense programs of the U.S. The technology development involves extensive theoretical, numerical, and laboratory programs, as well as construction of the WIPP facility in southeastern New Mexico for in situ testing and waste storage demonstration. If after the demonstration, the facility is found to comply with regulations of the Environmental Protection Agency, then the facility will become a repository for Transuranic (TRU) waste. The underground portion of the facility is 655 m beneath the ground surface in massive natural salt deposits of the Salado formation, as shown in Figure 1.

Jan 1, 1991

By MATTHEW HART, THOMAS BAMFORD, Kamran Esmaeili, MICHAL KOWALCZYK, FILIP MEDINAC

Improved haul road conditions can positively impact mine operations resulting in increased safety, productivity gains, increased tire life, and lower maintenance costs. For these reasons, a monitoring program is required to ensure the operational efficiency of the haul roads. Currently, at Bald Mountain mine, monthly site severity studies, ad hoc inspections by frontline supervisors, or operator feedback reporting is used to assess road conditions. These methods are subjective and provide low temporal resolution data. This case study presents novel unmanned aerial vehicle (UAV) technologies, applied on a critical section of haul road at Bald Mountain, to showcase the potential for monitoring haul roads. The results show that orthophotos and digital elevation models can be used to assess the road smoothness condition and to check the road design compliance. Moreover, the aerial mapping allows detection of surface water, rock spillage, and potholes on the road that can be quickly repaired/removed by the dedicated road maintenance team.

Sep 15, 2020

By Jerry Williams

GEORGE WEINMAN: At this time, our co-chair, Jamie Davis from Phelps Dodge, will come to the podium. JAMIE DAVIS: Our next speaker is Jerry Williams from Phelps Dodge, Morenci. Jerry is the maintenance planning supervisor and is in charge of preventative maintenance and maintenance scheduling. Jerry's group uses predictive tools to monitor and predict the equipment failure throughout the mine, from pumps to shovels to motors, you name it. The title of Jerry's talk is "If You're Not Using Predictive Tools, You're Behind the Curve." I’ll turn it over to Jerry.

Jan 1, 1998

By P. Sander, M. Spiegl, J. Reilly, A. Van Droogenbroeck

Although the outdated idea of calculating risk as the deterministic product of its likelihood and impact is not entirely a thing of the past, a multitude of organizations have adopted the usage of probabilistic methods for risk analysis, as they better reflect the inherent uncertainty of cost and risk estimates with ranges. But are these advancements sufficient in a complex environment such as tunnelling projects, where inadequate modelling of cost and risk can result in estimate discrepancies that run into millions of dollars? This paper explores two advanced probabilistic modelling techniques for tunnelling projects. The first one demonstrates how the cost and schedule uncertainty related to changes in excavation and support classes can be modelled with correlated variables. The second example models the risk related to explosive ordnance clearance on construction sites using a probabilistic event tree.

Dec 1, 2022

By Vas P. Srinivasa

A comminution circuit is an important integral part of a mineral processing plant. Nearly 40% of the capital cost and 30 to 40% of the operating cost are taken up by the crushing and grinding circuit. Therefore, considerable care should be given to the design and selection of this circuit. Several factors affect the selection of a comminution circuit--energy consumption, avail- ability of the equipment, the remoteness of location, and availability of trained personnel, to mention a few. Each of these factors influences the choice. Selecting a comminution circuit strictly on lower capital cost may not be optimal. Crushing and grinding circuits are usually site specific and should be selected - only after careful analysis of all the factors involved. The objective of this paper is to show the effect of these factors, which are extranious to capital cost. Usually, the capital cost of a semiautogenous grinding circuit is lower than that of an equivalent conventional circuit. However, due to lower equipment availability and high power costs in certain locations, the economic advantage of lower capital cost is lost. Analysis indicates that a break even point occurs at a power cost of 5¢/kWh. This paper describes the procedure utilized for selecting the most economic comminution circuit and states the conditions applicable for each cominution circuit.

Jan 1, 1983

By E. J. Karges

[For reasons well known to Mining Engineers, fine grinding in the wet form is quite universal inn plants engaged in the traction of metallic values from crude ore In the processing, of non-metallic and industrial minerals, however, fine grinding in dry form is the more common method. The crude materials generally contain less moisture than required for wet grinding, and the products are usually marketed or used in the dry form, most of them as powders. To grind wet would therefore entail the addition of water and the expense for drying the product, which is not justified. This paper will concentrate on the particle size reduction or fine grinding of materials to produce a dry powder]

Jan 1, 1963

By B. G. White

Traditional interpretations of vein ore deposits in the Coeur d' Alene Mining District, such as the view that these deposits formed in a transcurrent tectonic regime during the Precambrian, are being supplanted by the view that the deposits (1) formed in low-grade metamorphic shear zones similar to those that host an important type of gold deposit, (2) display features, such as wall rock carbonate zoning and vein zoning, that are common to ore deposits elsewhere, and (3) are probably Mesozoic and possibly related to emplacement of the Idaho batholith. In recent years, new interpretations have led to major ore discoveries that are likely to extend the life of the district for decades.

Jan 1, 1998

By Craig M. Sams

Matching mill? drives to mill power draws is a relatively new practice with the introduction of variable speed drive arrangements. Semi-autogenous grinding (SAG) mills are the focus of this paper as ball and rod mill characteristics are easily charted as charge loading and speed change. In addition, a look at types of drives available in the market and mechanical ratings is outlined to match the specifics of each drive.

Jan 1, 1991

By Douglas J. Lootens

Geologic mapping was undertaken in the Sierrita Mountains as part of a Doctoral program at the University of Arizona, Tucson. During the study, approximately 35 square miles was mapped in detail, with particular attention given to specific areas of great or significant structural complexity and their relation to mineralization in the vicinity. A combination, of field studies and photogeologic interpretation was used in order to define regional and local structural controls for disseminated copper-molybdenum mineralization in and adjacent to the study area. Gratitude is expressed to the faculty of the University of Arizona, Department of Geology for their assistance in this work and to Bear Creek Mining Company for making numerous reports and drill cores available for study.

Jan 1, 1965

By Mingfei He, Jianhua Chen, Yingchao Liu, Yuqiong Li

Pyrite is one of the most common sulfide minerals on earth, which is usually grown with chalcopyrite and other sulfide minerals. In flotation practice, pyrite from different mines or different sections in a same mine may have different flotation behaviors. This is because the pyrite crystal contains lattice defect, including ionic vacancy and lattice impurity. The present work investigates the effects of three typical 3d transition metal (Co, Ni, and Fe) on the adsorption of CH3OCS2 −, OH−, and CN− on pyrite surface by density functional theory (DFT) calculations. Calculated results show that Co impurity reduces the adsorption energies of CH3OCS2 − and CN− on the surface of pyrite, while Ni and Cu impurities significantly increase the adsorption energies of CH3OCS2 − and CN− on the surface of pyrite. Co impurity has small influence on the adsorption of OH−, but Ni and Cu impurities significantly increase the adsorption energies. Calculations on Mulliken charge population of Co2+, Ni2+, and Cu2+ indicate that the Mulliken charges of Co2+, Ni2+, and Cu2+ after OH− adsorption are more than those after CN− adsorption. This suggests that the ionic property of the M-OH- coordination bond is greater than that of M-CN- coordination bond, while covalent bonding of M-CN- coordination bond is greater than that of M-OH- coordination bond. The adsorption results are discussed based on coordination field theory (CFT).

Oct 6, 2020

By C. L. Van Dover

Organisms living at hydrothermal vents are adapted to catastrophic disturbances in their environment caused by processes such as tectonic activity and mineralization that shift the locus of fluid flux and volcanic eruptions that pave over active systems and reset the hydrothermal cycle. The scientific community appreciates this risk of natural, local loss of species, genetic, and habitat diversity. The risks of more profound loss of diversity and ecosystem function and health as a consequence of additive commercial activities in hydrothermal systems are unknown, and are not the same across all deep-sea hydrothermal systems. Vent communities differ from one ocean basin to another, as do the geological settings and geochemical dynamics of vent systems. Communities on the East Pacific Rise represent one end-member in the catalog of hydrothermal vent communities. In these systems, the life cycle of a hydrothermal field is on approximately the same time scale as the lifespan of the species that live there. From studies of the 1991 and subsequent eruptions at 9N on the East Pacific Rise, we understand the rapidity with which new vents are colonized when nearby brood stocks are available to repopulate the system. Almost instantaneously, microbial biofilms and mats form, followed quickly by invasion of mobile opportunistic organisms (especially crabs, copepods). In a matter of a few months, a predictable succession of sessile organisms recruits, grows, and reproduces. Within two to three years, the system returns to levels of species diversity that begin to match those of the pre-eruption condition. Vents on the Mid-Atlantic Ridge (MAR) represent a different end-member, with catastrophic disturbance rare relative to the life span of the organisms that make up the bulk of the biomass. We have no experience with an eruptive event or other major transformation of venting activity on the MAR and thus have no knowledge or insight regarding the time it would take for the biological diversity to return to pre-cataclysmic levels.

Jan 1, 2008

By John C. Nichols

The Ouachita, Ozark-St. Francis, and Mark Twain National Forests are located within the Ozark and the Ouachita Mountains regions of southern Missouri, central and northern Arkansas, and eastern Oklahoma- an area generally referred to as the Ozark-Ouachita or Interior Highlands. These national forests share many similarities in geography, biotic resources, and areas of shared public, market, and user interests. The three national forests have joined together to evaluate the natural resources within the Highlands and to study the impacts of the forests on local and regional economies and on the people who use these national forests and their resources. Other federal, state, and local government agencies and universities have joined with the Forest Service in this project, broadening the assessment area beyond the national forest boundaries to include 107 counties in Arkansas, Missouri, and Oklahoma. The diverse, resource-related data for the as- sessment area address social, economic, terrestrial, and aquatic issues and conditions throughout the Highlands. The assessment report currently is being developed by the Forest Service and will include an accoMpanying CD-ROM. The Ozark-Ouachita Highlands assessment has provided a forum for minerals- and geology-related resources, industries, social significance, and potential to be profiled and discussed along with other critical assessment resources. The state geological agencies in Arkansas, Missouri, and Oklahoma were active contributors to this effort. Their reports and other key data bases developed and used for the minerals sections of the published assessment report will be available either as a supplemental CD-ROM or on the Internet. Updated information on the progress of the assessment report can be found at the Ouachita National Forest Website, at <http://www.fs.fed.us/oonf/ouachita.htm>. This will also include a matrix displaying the minerals in the assessment area, their occurrence by assessment-area counties, and a potential ranking, as well as information on interesting geologic features. The state and federal reports, resources, and data bases, have helped answer key questions concerning mineral resources and related issues in the Highlands:

Jan 1, 1999

By P. Sarnoff

Gold has always been a crisis investment. For centuries gold has been considered globally the money of last resort. In time of war, inflation, financial uncertainty, political upheaval there has with few exceptions always been a flight to gold. The gold paradox simply is that even though we have gone through for the past handful of years all the kinds of. anxieties that would cause the gold price to rise, it has instead dropped drastically. Figure 1. illustrates the important factors that influenced the gold price significantly up or down before 1987. Obviously, since then, even though we have had wars, inflation, financial problems involving breaking banks and thrifts let alone collapsing financial institutions, the gold price has both in the long-term and the short-term trended downwards. Figure 2. depicts the gold price path since 1987. If the presence of time-honored and time-tested factors that should have driven the gold price up didn&apos;t do the job, then logic dictates that new factors to drive the gold price down and keep it depressed arose. And they did. But before addressing these depressants permit me to turn to the arcane art of gold price prediction and fore-casting.

Jan 1, 1992

By Donald W. Gentry

This paper presents some of the results of a rock mechanics in¬strumentation program designed for, and implemented at, longwall panel 4N at the York Canyon Mine near Raton, New Mexico. The objective of this particular instrumentation program was to determine the response of the rock mass to longwall mining of a thick coal seam utilizing shield-type supports. Measurements were made in the rock along the ground surface, above the coal seam, in the coal seam and immediately below the coal seam. Longwall test panel 411 had a total developed length of 762 m (2500 ft) and a face width of 168 m (550 ft). The seam mining height in the panel area was approximately 3 m (10 ft). The average depth of overburden above the panel is 107 m (350 ft) al¬though it ranges from 73-134 m (240 - 440 ft). Roof support at the face was provided by Hemscheidt shields. These shield-type supports weigh 11.4 metric tons each.

Jan 1, 1977