Search Documents

By G. Bräuner

The methods of burst control treated in the authors' very informative paper have been applied in the Ruhr Coalfield, Germany, for more than 20 years and have proved to be highly effective. It might be interesting here to mention a few experiences: The symptoms of critical stresses when drilling with small diameters ("test drilling") are essentially the same as described. However, we consider the situation safe if these symptoms occur beyond a certain distance ahead of the face. That safety distance equals three times the seam thickness plus the daily advance. It is the total seam thickness that counts, not merely the mined portion. Critical stresses within the safety distance are dissolved by so-called destressing measures: drilling with heavier equipment, blasting, or water infusion. To avoid bump initiation, the destressing operations should begin at the sides of the stressed zone rather than in the middle. As to water injection, there are two different principles. If the situation is critical already, high pressures are applied for hydraulic fracturing. If the stresses still allow to drill deep holes, the fluid pressure is kept low and acts for a longer time. This is to make the coal break successively instead of violently - a long-term precaution. When the stresses are very high, destressing is the most appropriate means. We mostly drill with 95 mm-diam (3.7 in.- diam). The techniques in detail are somewhat complex and subject to modifications. But the general idea is to accomplish burst prevention by controlling the potential burst situations.

Jan 1, 1990

By J. Hanna, I. Anazia

Selective fatty acid flotation of carbonate gangue from sedimentary apatites was achieved under acidic pHs without a specific apatite depressant and without conditioning the pulp with the collector. Concentrates (35% to 38% P2O5, 0.8% to 1% MgO) with high recoveries (80% to 85%) were produced from Indian and Chinese dolomitic ores. The calcareous and/or dolomitic-siliceous phosphate ores of South Florida and Utah required two flotation stages: one for carbonate removal, as mentioned above, and the other for phosphate recovery from siliceous gangue. Preliminary tests on the South Florida ore gave concentrates analyzing 29% P2O5 and 0.8% MgO, with a P2O5 recovery of 76%. A concentrate obtained from the western US phosphate ore from Utah assayed 30% P2O5 and about 1% MgO, with a P2O5 recovery of 89%.

Jan 1, 1988

By David McGregor, Ashoke SenGupta, Jerry Darlington

The stability of bentonite clay suspensions against flocculation in the presence of certain anionic polymers was investigated. These polymers included a purified sodium lignosulfonate, a sodium oxylignosulfonate, a potassium salt of humic acid, and a sodium polyacrylate. The polymers differed from one another in molecular weight as well as in carboxylic, phenolic, and sulfonate group contents. The scope of this study is in evaluating the extent of thinning achievable in a bentonite clay suspension in the presence of these anionic polymers under varying electrolyte concentration, presumably as a result of deflocculation of the clay platelets by the polymers. Under certain conditions of polymer dosage and electrolyte concentration, the lignosulfonate seemed to have flocculated the clay suspension, while the other polymers served fairly well as a deflocculating/dispersing agent. The lignosulfonate, however, showed some deflocculating ability when the electrolyte concentration of the suspending medium (water) was increased by adding sodium chloride to the clay suspension. Among the four polymers tested, the polyacrylate was found to be the most effective in deflocculating clay particles, followed by the humate and the oxylignosulfonate.

Jan 1, 2003

By I. Longson

Maintaining control over underground environmental conditions in the United Kingdom is increasingly dependent on the contribution of underground booster fans. Given the recent trends of higher rates of production from a fewer number of coal faces with higher levels of mechanization and higher power consumption, the effect has been to place a greater load on the mine ventilation system. This has increased the scale of potential problems that may arise should any of the main ventilation control devices not perform at the required full duty. This is particularly true for underground booster fans. Major changes occur in the main ventilation parameters on the stoppage or restart of a booster fan which results in a temporary loss of environmental control. This paper analyzes the impact of such events and details a mathematical model thar has been developed for a single-mesh circuit containing a main and a booster fan. Predictions based on this simple model are presented and discussed with particular reference to the energy changes occurring within the ventilation system immediately following a booster fan stop or restart

Jan 1, 1995

By P. Massacci

This study deals with the development and utilization of computer models for evaluating the extent to which variability of raw material grades can be reduced from the deposit to the processing plant. The specific case of a cement works is examined. The deposit and the elementary quarring operations were modeled for the medium and long-term planning of production with the objective of predicting grade variability of the flow stream in time. The feeds inferred from previous modellings were used for simulating storage operations. In particular, the storage process (linear stockpile, as an alternative, blending from various heaps) was modelled in order to select the main parameters of the process to minimize grade variations of the feed to mill. The ways followed for modelling the prehomogenization process are described. The homogenization performance and efficiency in the silo stage has also been studied and an estimate made of the distribution of residence time on the basis of input and output sampling.

Jan 1, 1986

By P Moser

Within the EU-research project "Blasting Control", jointly operated with partners from France, Italy and Greece, between 1992 and 1995, the Department of Mining Engineering of the Montanuniversity Leoben, Austria took over the task to develop a diagnosis system applicable in underground drifting, in order to identify possible reasons for blast failures or poor blast performance. For that purpose 120 m of 12 m2 test galleries were excavated at two different mine sites. For every blast performed the collar and bottom position of every hole drilled, the charged hole length and the drift and face profile of the round blasted were monitored. These 'geometrical" data were put directly from the measuring devices into SURPAC, the mine planning software chosen for data analysis. Based on the data computed, 3D plots comparing actual and planned data were made visible on the screen or as hard copies. Experience from the introduction of this system into a mining operation showed, that the system developed contributes to an improved understanding of the reasons for blast failures and forms the basis for an improved blast design. The soft- ware package SURPAC was also used to train the miners directly at the mine site in order to improve the quality of their work.

Jan 1, 1996

By R. W. Seedsman

Mandalong Mine was originally planned to operate with panel widths of 250 m and a predicted surface subsidence in excess of 3 m. The consent conditions applied by the NSW government on this mine plan were very tight and, following a change in ownership, were considered by the new operator to present a number of unacceptable business risks An acceptable risk profile for the mine layout restricted surface deformations to less than 500 mm vertical subsidence, less than 7 mm/m tilt, and less than 5 mm/m strain. Empirical subsidence prediction methods indicated that it would be necessary to reduce extraction panel widths of 80 m - an uneconomic option. The application of a number of rock mechanics concepts identified that the local overburden geology could be exploited such that panel widths of up to 175 m could be possible. The 125 m width was selected as a low-risk introduction of this new subsidence prediction method. The extraction of the first 2 longwall panels has demonstrated the validity of the prediction subsidence method and has provided the opportunity to refine the selection of key input parameters. The impact of mining through a zone of thrust faults was successfully predicted. The mine is now planning the introduction of 160 m wide panels, and will review the associated subsidence impacts prior to any further increases in width.

Jan 1, 2006

By John M. Wootten

The development of new coal markets is -t upon the ability to utilize coal in an environmentally acceptable and economically viable fashion. Foremost in the concerns about coal utilization is the impact its combustion has on air pollution. Concerns over environmental issues, such as acid rain, are currently one of the major impediments to the development of new coal markets. The Department of Energy and the Synthetic Fuels Corporation are addressing certain aspects of the development of new technologies for the utilization of coal. However, at the present time, there is a void in the new technology development process. That void is the step from proof- of-concept to commercial demonstration. Congress has established the Clean Coal Technology Fund at a level of $750 million to fill this void. The Department of Energy, in a solicitation of interest, received over 175 proposals for commercial demonstrations of clean coal technologies. A review of these solicitations indicates that $1.2 billion worth of research could be accomplished with a federal cost sharing of $425 million or 35 percent of the total. Industry has indicated, through this response, its willingness to invest its limited funds on projects it feels have the greatest potential for the clean use of coal. What must now occur is that Congress must appropriate the monies from the fund to initiate the commercialization of these clean coal techno1ogies.

Jan 1, 1986

By M. K. Gangal, E. D. Dainty

The CANMET diesel-related work, carried out in cooperation with the Canadian mining industry, resulted in the identification of several useful R/D studies. One such study was the development of a dash-mounted alarm signal system to indicate overexposure of production LHD diesel vehicle operators to toxic contaminants in a mine environment. The resulting instrument has been called the [CO2 Exposure Meter]. This meter is particularly applicable to LHD machines because previous investigations have indicated that operators of LHDs and some haulage truck drivers are exposed to up to 200% of the contaminant concentrations measured in the general mine return air. This paper describes the development of the system which continuously monitors and displays the operator's exposure to diesel pollutants, and indicates an overexposure by an alarm light. The overexposure limits are preset by mine personnel based on carbon dioxide (CO2) measurements, which in turn are related to simultaneous spot respirable combustible dust (RCD) measurements (or to Air Quality Indices - AQI, if available). The CO2 settings are, in general, related to the engine/exhaust treatment selections, vehicle duty cycle and local ventilation rates and efficiency. The system continuously displays one of three lights: green for underexposure, yellow for caution, and red for overexposure. Overexposure can occur for several reasons, such as: reduced ventilation, malfunction of the diesel vehicle, and excessive airborne contaminants. The paper confirms satisfactory operation of the system in a laboratory-simulated mine environment, as well as in field trials.

Jan 1, 1993

By K. C. Jordi

Many systems which are modelled mathematically result in a model where the relationships between some or all of the parameters are found to be non-linear. These systems are usually complicated further by a desire to make the system achieve multiple and often conflicting objectives or goals simultaneously. Rozwadowski (1970) developed a model to describe the total discounted net profit of a mine as a function of the amount of ore developed and of the grade of the amount of ore mined. Dynamic programming was used to determine the policy which gave the maximum net present value. In this paper it is shown that the relationships between the variables can be approximated by piecewise linear functions. This is amenable to solution by an algorithm based on the simplex algorithm of linear programming. The goals of maximizing the net present value, the total net profit and the total gold output are incorporated simultaneously into a goal programming formulation of the system. The resulting model is characterized by a large number of disconnected constraints. These are decomposed into several smaller problems and the problem solved. The solution is examined to discover the sensitivity of the system to changes in certain parameters. In particular the interaction between the three goals is analysed to determine whether there is conflict between any of the goals and, if so, what the trade-offs between the conflicting goals are.

Jan 1, 1979

By Por J. B. Evans

El mantener un beneficio óptimo sobre todo el conjunto de un emplazamiento minero necesita una constante puesta al día de las estrategias operativas. En esencia, cada estrategia es una combinación particular del gasto del capital previsto, el flujo de ingresos y el tiempo transcurrido. La selección de una estrategia basada en el beneficio potencial requiere que cada estrategia contemplada con un ordenador, un análisis tal puede ser engorroso. Este capítulo discute o desarrolla una técnica de "corte rápido" que asigna una relación de beneficio a las estrategias alternativas e identifica aquellos aspectos de una estrategia que producen mayor impacto sobre el beneficio. Esta técnica puede proporcionar valoraciones rápidas de suficiente precision para muchas de las decisiones de las estrategias operativas que se toman sobre la marcha en minas que se encuentran en explotación.

Jan 1, 1982

By M. K. Gangal, E. D. Dainty

CANMET/MRL has been contributing to an industry/government program to assess the quality of air in mines, and improve the working environment for Canadian miners. The ultimate aim of this program is to recommend a sampling methodology and appropriate concentration limits for both the soot (diesel particulate matter - DPM) generated by diesel equipment, and respirable combustible dust (RCD) as measured underground. The program was conceived by the Canadian Adhoc Diesel Committee, which consists of representatives from seven major Canadian mining companies, three provincial inspectorates, one union representative, two manufacturers of diesel equipment, and CANMET, a Federal Canadian research agency. This paper describes the modification and laboratory confirmation of an existing methodology for the sampling and analysis of DPM/RCD, including: sampling problems, filter selection, filter efficiency, DPM size distribution, the approximate performance of fractionating devices, and it reports the results of current ambient measurements of exposure levels in Canadian underground mines. Because of the concern about the health impact of DPM/RCD on mine workers, North American agencies are in the process of establishing limits for these aerosols. So far, the Province of British Columbia is the only jurisdiction in North America to legislate the maximum exposure level of RCD in its underground mines, i.e. 1.5 mg/m3 interim level recommended by the Adhoc Diesel Committee. It has also recommended the use of the CANMET/ADHOC RCD sampling protocol.

Jan 1, 1993

By Robert W. Waytulonis

Miners working in underground mines where diesel equipment is used are exposed to exhaust pollutants. These include carbon monoxide (CO), carbon dioxide (CO,), nitric oxide (NO), nitrogen dioxide (NO2), sulfur dioxide (SO2), hundreds of different hydrocarbons (HC) and particulate matter. Evidence from animal inhalation studies and limited epidemiological investigations have led the National Institute for Occupational Safety and Health (NIOSH) to recommend that ‘... whole diesel exhaust be regarded as a potential occupational carcinogen ...’ NIOSH further stated that ‘... the excess cancer risk for workers exposed to diesel exhaust has not yet been quantified, but the probability of developing cancer should be decreased by minimizing exposure…’ The International Agency for Research on Cancer(IARC) reached a similar conclusion, saying that ‘... diesel engine exhaust is probably carcinogenic to humans.’ Before these declarations, there was insufficient evidence concerning the carcinogenicity of diesel exhaust. It was well known, though, that diesel exhaust caused less severe problems, such as headache, eye irritation and unpleasant odors. In 1988, a milestone was reached in the Mine Safety and Health Administration (MSHA) regulatory process. An advisory committee recommended a three-tier approach to regulating diesels used underground-approval of diesel equipment, safety and health. Diesel particulate matter may be specifically regulated. In addition, ambient air quality standards are being proposed that will establish a new standard for CO2 and lower the permissible exposure limits for the NO2, CO, SO2 and formaldehyde emissions that originate from diesels and other sources. Additional safety and emission restrictions are also proposed for diesel engines in coal mines. The goal of the US Bureau of Mines (USBM) diesel engine research program is to minimize the health and safety problems associated with underground diesel equipment use. Part of this program is focused on reducing exhaust emissions from diesel-powered equipment used in underground mines.

Jan 1, 1993

By Max John

INTRODUCTION One of the main advantages of the New Austrian Tunneling Method (NATM) is its adaptability to varying rock conditions. This method is therefore successfully applied when complex geologic features are expected which cause uncertainties in the prognosis of the rock mass behaviour, as was the care at the Arlberg Expressway Tunnel. Furthermore, by employing the NATM problems are avoided when encountering varying geologic conditions or even extension fault zones along the tunnel, as was the case at the Dalaaser Tunnel and Perjen Tunnel. The NATM can also be used for rock and soil. The following examples will show how various rock conditions can be mastered. In accordance with the NATM all tunnels which will be discussed are road tunnels having a cross section area between 70 and 100 m2. The construction consists of a primary support, which ensures stress redistribution during excavation (Figure 1). The primary support is reinforced shotcrete strengthened by steel arches, when necessary, and rock bolts. When encountering rock pressure, swelling rock or soil, the primary support is suplemented by an invert arch. The purpose of the secondary lining is to increase the safety of the tunnel with regard to long-term stress redistribution processes or changes in rock mass properties as well as to protect the insulation. The secondary lining consists of cast concrete without reinforcement and is generally 0.25 or 0.30 m thick.

Jan 1, 1981

By J. A. Finch, J. Yiantatos, A. R. Laplante

This paper re-examines the mixing conditions in the collection zone of flotation columns. These have in the past been characterized with a single uniaxial dispersion coefficient, E. The relationship between E and column diameter, Dc, is examined based on residence time distributions (RTDs) in columns of Dc ranging from 5.lcm to 184cm. Results agree with published correlations in chemical engineering, i.e. E a Dc '" , Data explain why pilot columns display significant upgrading between the feed level and the interface, whereas plant columns do not. It also suggests that, for plant columns, the full collection zone (up to the interface) can be considered when calculating the residence time. A mathematical model considering two regions of different mixing was compared to the single E model. Both models adequately fitted measured age distributions inside the column and overall RTDs. Measured and simulated mixing characteristics are compared to those of flotation banks, using a tanks-in-series approach; banks of comparable mixing to columns are identified.

Jan 1, 1988

By J. Villeneuve, G. Fourniguet

Simulation of Mineral Processes is now commonly used by the Engineers in charge of plant design or optimization but a good knowledge of the simulation tool is still needed to conduct a project. A new level of algorithm has been defined above the simulator to answer directly to the user's questions. This level has been called the supervisor of simulation, which is using the automation concepts of sensors and actuators. At any place of the flowsheet (i.e., a stream or an equipment), the user may indicate which value could change by graphically implementing an actuator. Then, he can evaluate the effect of the variation of this value at any other place of the flowsheet by inserting a sensor. Thus, by example, it becomes possible to look at the evolution of the recoveries and/or the circulating loads when scanning an interval of the possible teed flowrates. This approach conducts to an increased facility in using a simulator and in analyzing the predictions. It is also a very valuable tool for permitting to characterize the sensibility of the simulation results to the variation of some settings (e.g., load of grinding media, rotation speed, water addition, etc.) or feed characteristics (e.g., flowrate, sizes, grades, grindability, etc.). Thus, the most important variables can be identified for design and pre-control optimization of plants. This new level of simulation will be implemented in a further version of the USIM PAC simulator and selected examples are presented.

Jan 1, 1995

By S. W. Kan, M. G. Kakarkis, J. Zelanco

Grouting has been used in underground mining for more than 20 years. Chemical grouting is often used as a remedial measure when the implemented ground-control program is unable to completely prevent structural failures or when there is a need for preventing a structural member from unraveling. The utilization of polyurethane grout is restricted by its limited range of physical and mechanical properties. To overcome some of the drawbacks of polyurethane, research is being conducted on a newly developed polyester based grout. The polyester resin, identified by Sandvik as Strata Grip, provides a number of features, including variable gel times and a much-reduced chemical hazard. Equally important are the mechanical properties of the product. The strength and deformability of any chemical grout must be compatible with the intended purpose of grouting and the expected deformation of the rock that is to be grouted The assessment of the mechanical properties of polyester grout is the focus of this work. Field experiences and laboratory research defined the properties of an effective grouting material. Experimental results indicate that the polyester grout meets or exceeds the recommended properties for many injection applications. Furthermore, the results suggest that the ability to adjust mechanical properties via resin formulation has the potential to expand the applicability of chemical grouting in ground control.

Jan 1, 1999

By Numan Elmas

This paper presents detailed information on the genesis, formation, and industrial utilization of Yaylacik magnesites. Tectonically, the study area is located within the Tavsanli Zone, immediately south of the Izmir-Ankara suture in western Turkey. The geologic setting mainly comprises ophiolitic melangks basics, and ultrabasics associated with very rich magnesite deposits and lacustrine sediments. The ophiolitic unit tectonically overlies the schists and carbonate rocks. The presence of glaucophane and lawsonite indicates a low-temperature/high-pressure metamorphism. The ultra- basic rocks, which exhibit cumulate composition, have been mostly serpentinised and represent the oceanic floor of the Yaylacik ophiolite. Basic intrusives consist of dolerite and diabase, and they show the characteristics of within-plate dolerites. The magnesite occurrences are commonly observed in block, stockwork, lens, and vein forms and were deposited within the serpentinites. In most magnesite samples, secondary quartz/chalcedony formations are observed as fracture fillings due to the highly effective tectonic movements. Field surveys and microscope studies reveal that magnesites had been formed by the metasomatic alteration of serpentinites. Chemical analyses show that, although MgO content of the magnesites varies from 43.41% to 50.48%, Fe203 and CaO are lower than 1%. Silica contents are as high as 5.52% in a few samples. Although Yaylacik magnesites are not suitable for making basic refractory bricks, they are widely used as caustic-calcined magnesite in a variety of applications, including animal food, artificial fertilizer, chemical (acid neutralizer), medical and pharmaceutical, and water treatment.

Jan 1, 1999

By J. W. Hawkins

Understanding aquifer properties in surface mine backfill is essential for managing the groundwater flow system as well as controlling the formation and discharge of acid urine drainage. Slug tests (injection and withdrawal) performed on wells in mine spoil may yield two distinctly different response characteristics. One type of response is indicative of a porous media system. The second type of response indicates the presence of a pseudokarst system. The presence of voids or conduits in the backfill is indicated by an almost instantaneous partial recovery of the water level displacement. This rapid recovery is turbulent flow and cannot be analyzed by conventional (Darcian) methods. The turbulent flow may cause the calculated hydraulic conductivity to be less than the actual values. The slug dissipation surface area created by the voids contiguous to the test well add to the known dissipation surface area of the screened interval. This can cause the calculated hydraulic conductivity to be greater than the actual hydraulic conductivity or the aquifer to appear more permeable. Whenever analyzing data from aquifer tests in mine spoil, these potential problems must be kept in mind. In spite of the problems encountered during slug testing of spoil, the aquifer hydraulic parameters derived and the slug responses observed remain useful in the hydrologic characterization of a mine site.

Jan 1, 1994

By Fred W. Stuart

Microprocessor technology has revolutionized the business community by placing tremendous computing power in the hands of the end-user for a very inexpensive price tag. The range of applications covers process control, to office automation, to personal computing capabilities. With the influx of this new technology, which these systems have to offer, also comes some unique operational and control considerations. But before we address these items, let us lay a foundation of common terms to be used throughout this presentation. Due to the rapid advances in microprocessor technology, where a new generation of computers is announced every two or three years, it becomes difficult to define a microprocessor system and have it valid for an extended period of time! Therefore, for this presentation, we will be dealing with a subset of microprocessors called Personal Computers or PC's. At the heart of a PC is a Central Processing Unit or CPU. The CPU performs the actual program and command execution. The programs dealing with driving the various peripheral equipment is referred to as the Operating System (for example: DOS : Disk Operating System, CP/M - Control Program/Microcomputers, etc.). The CPU is normally housed in an enclosure which contains power regulators, peripheral equipment interfacing 'cards', and expansion 'slots' to enlarge the capabilities of the PC system.

Jan 1, 1989