Search Documents

By C. B. Manula

A method for the feasibility assessment of open-pit operations using conventional shovel/ truck systems to mine steeply pitched coal seams has been applied at The Pennsylvania State University. Three computer models were developed for the analysis: a geology and reserves model (GEOL), an open-pit materials handling simulator (OPMHS), and a cash flow model (CASH) (Manula, Albert, and Burgos, 1976). GEOL provides the basic mining data; OPMHS simulates shovel/truck performance related to pit profiles and average mining locations to provide productivity rates needed to size the system; and CASH provides either a selling price or rate of return (ROR) for the product. The general flow of information generated by these models is shown in Fig. 1. Since the ratio of overburden-extracted to coal-produced places a definite economic limit upon a mining venture, geological data must be analyzed with the least possible manual effort to minimize computational errors. This is especially true if the property contains several seams that are steeply pitched. In this situation, a computerized analysis is by far the most efficient and effective method to determine coal reserves and waste tonnage. This chapter describes the reserve model developed at Penn State and provides an example to demonstrate its application.

Jan 1, 1979

By M. J. McPherson, P. Mousset-Jones, G. Danko

Ventilation and refrigeration fortune climate modification contributes significantly to the operating costs of a deep hot mine. Mine climate simulation programs can he used to minimize the impact of these costs. There are several computer codes available to assist in this work. Whichever simulation program is used, it is the mine ventilation engineer who must supply the input data. This paper raises and answers the following question, namely, what accuracy is required of the basic input parameters, in order for a certain precision to he obtained in the predicted air temperatures? In the first part of the paper a new approach is described to estimate the dry and wet bulb temperature of the airflow, either in a dry or wet roadway. The calculation procedure allows an arbitrary temperature change with time, using Duhamel's superposition solution. Matrix-vector representation is applied to simplify the computational structure. In the second part of the paper the sensitivities of the dry and wet bulb air temperatures are analyzed, to the changes of the rock thernrophysical properties, the heat transfer coefficient, and the wetness factor.

Jan 1, 1987

By J. F. T. Agapito, J. B. Page

This paper describes part of a geotechnical study based on stress determinations and convergence measurements conducted to assess the long-term stability of an experimental room-and-pillar oil shale mine. A rock mechanics program was initiated in 1971 at the Colony Mine as part of a large study conducted for the design of a commercial operation. The Colony Development Operation is a joint venture currently consisting of four active members; Ashland Oil Inc., Atlantic Richfield Company (Operator of the project), Shell Oil Company, and The Oil Shale Corporation. Although oil shale commercialization plans are presently suspended, rock mechanics instrumentation has been continued as part of Colony's policy in maintaining readiness to proceed with a commercial shale oil plant when national energy policies became better defined. The property is located in the southern edge of the Piceance Creek Basin in northwestern Colorado, approximately 200 miles west of Denver. Experimental mining operations were conducted from 1965 to 1972 with one of the major objectives of the pilot mine being the assessment of opening and pillar sizes for the determination of extraction ratio and life of the property. Mining was conducted in a 60 foot thick portion of the Mahogany Zone in the Parachute Creek Member of the Green River Formation, at depths of 600 to 850 feet by a one-bench system. Pillar dimensions were 58 feet by 58 feet and rooms were 55 feet wide.

Jan 1, 1977

By F. D. Mendes, A. H. Martins

The high copper grade in the Igarapé Bahia (Brazil) gold-copper ore restricts the direct application of the classical cyanidation process. Copper oxide and sulfide minerals react with cyanides in solution, causing high leach-reagent consumption, raising processing costs and decreasing gold recovery. According to studies, a feasible solution would be to pretreat the ore to remove copper minerals prior to cyanidation. The goal of this experimental work was to study the conditions for the removal of copper from the Igarapé Bahia gold-copper ore by sulfuric acid leaching, applying a statistical approach to the experimental design. By using the Plackett Burman method, it was possible to select the variables that exhibited the largest influence on copper extraction at the sulfuric acid leaching stage. These variables were leach solution temperature, stirring speed, sulfuric acid concentration in the leach solution and ore particle size. The individual effect of these variables and their interaction influences on the experimental response were analyzed by applying the replicated full-factorial design method. Finally, the selected variables were optimized by the ascending-path statistical method, which determined the best leach experimental conditions for maximum copper extraction. The optimized leaching conditions resulted in a copper extraction of 75.5%. Keywords: Copper, Gold, Extraction, Sulfuric leaching, Optimization

Jan 1, 2003

By Robin J. Batterham, Stephen H. Algie

It is often stated that innovation is central to the economic survival of mining and mineral processing in the face of global competition, and yet technology is often far from a core strategy in our industry - hence the concerns that are often voiced about the apparent slow rate at which new technology is applied. Much of the discussion stems from a lack of understanding of the role of technology in innovation, and of the role of R&D within the innovation process. To a large extent this has all been said, however, the messages are clear and deserve repetition. This paper expresses the personal views of the authors, based on experience in government-funded (CSIRO and universities) research, and in CRA Ltd, a large mining and mineral processing company. Further than this, it explains how our own development unit within the CRA Group has come to see its key roles as including the transfer of technology, and the training of technologists to move into the operating business units. We conclude that these critical tasks are the keys to creating the environment that will allow us to maximise the contribution of technology.

Jan 1, 1995

By M. A. Marticorena, R. Stratton-Crawley, C. I. Basilio

Diethylenetriamine (DETA) is a selective depressant for nickeliferous pyrrhotite during pentlandite flotation. Laboratory flotation tests conducted on ore and process samples showed that pyrrhotite rejection is greatly improved by small additions of DETA; however, the effectiveness of this depressant is most noticeable when the mineral sample is oxidized. LIMS and XPS analyses conducted on flotation products and pyrrhotite specimens showed that the difficulty in pyrrhotite rejection arises from inadvertent activation of the mineral by heavy metal ions, such as Ni2+, cu2+ and Ag+, that are present in the process water. In the presence of DETA, however, the mineral is deactivated under oxidizing conditions. The deactivation mechanism may involve oxidation of the activation products, which are likely in the form of heavy metal sulfides, followed by solubilization by DETA. FTIR spectra of pyrrhotite electrodes contacted with DETA showed no trace of the reagent on the surface, substantiating the view that its role is one of complexing agent that enhances the dissolution of activation products under oxidizing conditions. FTIR spectra of pyrrhotite contacted with amyl xanthate solutions showed that both dixanthogen and iron xanthate are formed on the surface, the latter becoming more predominant at higher potentials. In the presence of DETA, however, only a small amount of xanthate is adsorbed on the mineral at potentials (Eh) approximately 200 mV higher than the case without DETA.

Jan 1, 1995

By J. T. Sitarski, R. C. Emmett, L. W. Luinstra, R. P. Klepper

A mining operation in Zimbabwe produces a pyritic gold concentrate that requires oxidative pretreatment prior to cyanidation in order to liberate 80 percent of the gold values. Bio- oxidation offered the potential of increased gold recovery and was considered to be an economically advantageous alternative to the existing practice of roasting the concentrate. Based on bench- scale test work, a small bio-oxidation plant, capable of processing approximately 50 percent of the concentrator production, was installed at the mine to evaluate this approach. The plant included two 57 m3 bioreactors in series and the ancillary equipment needed to prepare the feed concentrate, to wash the leached residue prior to cyanidation, and to neutralize the waste liquor. The plant was operated for a year-and-a-half, and the conditions needed to achieve a 90 percent liberation of gold values were determined. A number of critical technical problems were encountered, and many were resolved on-site. Others have been addressed since the pilot plant was moth-balled in June 1988. Valuable insight was gained from the operation of the pilot plant, which has provided useful guidance for continued process and equipment improvement.

Jan 1, 1990

By L. W. Stanger, Erich U. Petersen, William J. Tafuri, Donald M. Hausen, Douglas N. Halbe

Gold mineralization at the Mercur Mine was controlled primarily by structure and secondarily by lithology in Mississippian-age sedimentary rocks. Gold was localized where Sevier-age high angle northeast-striking faults are intersected by younger northwest-striking fault zones. The Lulu Graben is a northeast- striking fault zone composed of a south-dipping master fault coupled with subsidiary or antithetic faults. The Twist Fault zone, a sinuous, low-displacement , north-striking zone of fracturing, bisects the graben. Large- tonnage disseminated ore bodies formed east of the Twist Fault zone within silty, thin-bedded, bioclastic carbonates. West of the Twist Fault zone, gold was restricted to rock near peripheral faults surrounding a subvertical collapsed pipe developed within the graben. An overlying thick carbonaceous shale capped the ore zone. Presence of abundant limited- displacement faulting and of hydrothermal jasperoid is associated with cartonate-hosted disseminated gold. Conversely, increased fault displacement and widespread brecciation are associated with reduced dissemination of gold into normally receptive carbonates.

Jan 1, 1990

By M. Misra, I. Anazia

The dispersion of oily collector has a significant effect on the flotation recovery of ultrafine coal. Generally, reagent dispersion is accomplished by mechanical mixing and/or ultrasonic agitation, followed by direct addition of dispersed collector into the flotation cell. Such dispersion and reagent addition techniques are invariably inadequate and nonselective. A new collector addition technique involving gas phase transport of atomized collector has shown improved results when compared to conventional reagent addition techniques. This technique involves atomization of the collector into the air stream. Under these circumstances, an aerosol is introduced into the flotation cell. Initially, the oil is dispersed within the air phase (continuous with respect to oil), and the air phase is dispersed within the pulp (continuous with respect to aerosol). In the flotation cell, the atomized oil droplets coalesce on the bubble's surface and create a de facto oil-encapsulated bubble. This approach provides excellent dispersion, increases selectivity, and, most significantly, increases the flotation rate of ultrafine coal. Atomization of collector/frother combinations yielded improved flotation recovery and maintained near uniform froth levels, which is a desirable feature in coal flotation. Microscopic examinations of the attachment of oil- coated bubbles at a coal surface were conducted by attachment time and contact angle measurements. Oil-coated bubbles attach at significantly faster rates and with a higher contact angle than oil-free bubbles.

Jan 1, 1988

By W. J. Wuest, M. J. DeMarco, J. R. Koehler

Yield-pillar-based gate-road designs often fail to provide mine operators with adequate ground control. This is because of the unknowing m is employment of "critically" sized pillars. A "critical” pillar is one that is too large to either yield nonviolently or to yield before the roof and floor sustain permanent damage and is too small to support full abutment loads. To demonstrate the critical pillar concept, afield study of a tapering gate road was conducted by the US Bureau of Mines at the Sunnyside Coal Mines, Sunnyside, UT. Extreme pillar stresses and associated coal bumps characterize the response to first panel mining of a 16.8-m (55.1-ft) wide critical design. Significantly lower pillar stresses, early yielding of the pillar and adjacent panel rib, and an absence of coal bumps suggest that a narrower 12.2-m (40-ft) wide design more closely approaches proper yield pillar dimensions. A probe hole in several 10.6-m (34.8-ft) wide pillars revealed low stress levels and substantial pillar and panel rib yielding prior to abutment onset, indicating a properly functioning yield pillar design.

Jan 1, 1997

By T. A. P. Sankar, S. Gundiah, Pradip, R. A. Kulkarni

Two modified polyacrylamide flocculants, namely polyacrylamide with glycolic acid functionality (PAMG), and a copolymer of acrylamide with N-acryloyl-[T]- aminobutyric acid (HPVP), were synthesized, characterised and evaluated for selective separation in apatite/quartz and apatite/dolomite/calcite systems, respectively. PAMG flocculant was found selective in the separation of tricalcium phosphate (TCP) from its mixtures with quartz at acidic to neutral pH range. The selectivity deteriorated at alkaline pH. In contrast, polyacrylic acid (PAA) flocculant was found most effective only in the alkaline pH range. HPVP flocculant (even though flocculating all three minerals namely apatite, dolomite and calcite) was observed to be quite selective for the separation of calcite from apatite-dolomite minerals in single mineral tests in the presence of sodium hexametaphosphate dispersant at neutral pH. There was, however, no selectivity observed during tests on synthetic mixtures. This loss in selectivity is attributed to the phenomenon of hetero-flocculation, as reported earlier, for separation in an apatite-dolomite system with polyethylene oxide.

Jan 1, 1993

By S. K. Kawatra, T. C. Eisele

Coal-cleaning operations commonly produce a fine-waste stream containing a considerable amount of coal. The recovery of this coal is normally not economical because the coal is mixed with large amounts of difficult-to remove clay slimes and is often heavily oxidized or contaminated. Conventional froth-flotation machines cannot, in a single flotation stage, produce an acceptable product from such material, and even flotation columns often have difficulty cleaning this type of feed. A new type of flotation column was designed specifically to deal with these problems, and a column of this design was installed and tested in a coal-cleaning plant in Ohio. The feed coal tested was the plant&apos;s tailings-thickener product. The coal was 80% -176 µm and had a heating value of 8401 Btu/ lb. The coal contained 39.8% ash, as fine clay, and 2.83% total sulfur. Because previous attempts at conventional flotation of this type of material had been abandoned, plant personnel believed that the coal was too heavily oxidized and contaminated for flotation to be effective. However, by using the new column it was possible to recover up to 85% of the calorific value in a product containing < 11 % ash, and it was possible to recover 60% of the calorific value in a product containing <8% ash. In addition, the bulk of the pyritic sulfur was also rejected from the coat.

Jan 1, 1996

The stability of mine roofs in permafrost zones is determined mainly by temperature and ice content. The deformation resulting from creep and temperature-dependent physical properties of frozen rock mass is the dominant component of total deformation. Roof bolts can consolidate the roof and control its deformation. In this paper, a finite-element model, for the analysis of the effects of roof bolting in a frozen rock mass is presented. The model includes the variables normally encountered when analyzing the effects of roof bolting in rocks. It also accounts for properties unique to frozen rock mass: creep deformation and the change in Young&apos;s modulus with changing temperature. The model shows that, as bolt spacing decreases, there is a trade-off between increased roof stability from increased mechanical support and decreased stability from increased conduction of heat into the frozen roof. This result was expected and shows that, for a given set of rock-mass conditions, including ice content, temperature, particle size, etc., there is an optimum bolt length and bolt density for minimum roof deflection.

Jan 1, 1997

By Michael G. Nelson

Underground coal mining practice often requires that some coal be left in place at the seam boundaries after mining, for purposes of ground control, quality control, machine guidance, or good operating practice. Many methods for measuring the thickness of boundary coal have been developed, but only the natural % R gamma background method as bee used in routine operations. Use of this method is constrained by the level and consistency of the natural gamma background in the bordering strata, the accuracy of the gamma detection instrument, and the elevation profile of the seam boundary being detected. Computer simulations for three commercially available gamma detection instruments, designed for mine use, showed that measurement of boundary coal thickness by the natural gamma method can provide satisfactory input for horizon control systems when the gamma detector is large, when the sensor is mounted on the mining machine, and when the elevation profile of the seam boundary does not change rapidly in the direction of advance.

Jan 1, 1993

By Jean-Michel Rendu

The semivariogram is one of the most important tools available to the geostatistician for the analysis of mineral deposits. To be complete, a semivariogram study must include a minimum of three parts which are highly interdependent. These are: calculation of the semivariogram, mathematical modeling, and geologic interpretation. The known factors and conditions which controlled or influenced the distribution of mineralization within the body being studied should be considered in the analysis .of the semivariogram. The presence and characteristics of successive phases of mineralization, the chemical and physical properties of the host rocks and the mineralization should all be considered. This requires close and continued communication between the geologist and the geostatistician prior to and during the semi-variogram study. Geologic stationarity is needed if meaningful semivariogram results are to be obtained. The first step is, therefore, to determine whether the mineralization can be analyzed as a whole or if different geologically homogeneous sections must be defined and evaluated separately. Different methods can be used to calculate an experimental semivariogram from known sample values. The method chosen will depend not only on the anticipated and actual statistical properties of the deposit, but also on its geologic characteristics.

Jan 1, 1982

By Patricia O. Milley

Two years ago, AlliedSignal embarked on a journey to improve QUALITY. However, the focus of this endeavor was on the CUSTOMER and not the traditional product focus. It wasn&apos;t that a focus to improve product quality wasn&apos;t fruitful in the past. We&apos;ve practiced it in the chemical industry for many years with significant results. But our industry today is in a survival mode and yesterday&apos;s way of doing business is simply not good enough. In the mining industry, we have to make lug strides in how we do business or face losing our customer base. As you are well aware, other parts of the world are importing our technology at a rapid rate. We must work smarter to stay ahead of our customers ever more demanding need for higher quality at lower prices. With this as a driver, throughout the Corporation we reviewed in depth how we support our customers to keep them competitive and sought to eliminate work which did not help them reach this goal. Our first year of emphasis was on tools: how to hold meetings, gather data, and how to make decisions. This sounds very basic, I know, but you can&apos;t begin to imagine how productive meetings can become when you start with an agenda and prework delivered days in advance, and agree at the start of the meeting what should get accomplished. In the second year, we applied these tools to our work processes. We mapped how we do our work, scrutinized each step for value to the customer, and then set to work on how we could do things better. The areas we concentrated on were customer linked commercialization of new products, manufacturing and materials management. Our discussion today will focus on the commercialization of new products.

Jan 1, 1994

By H. Lyn Bourne

The is the 14th consecutive year for this column and the 13th in which the royalty data have been tabulated. Some holes still exist in the list of royalties that readers hopefully will fill. Construction aggregates - either sand and gravel or crushed stone - are the most common mineral commodity. In spite of their pervasive use nationwide, royalty information for these commodities has been difficult to acquire from some states. Readers can help. Share information about these missing states and next year there will be fewer states without information. Dennis Bryan sent a copy of a report, "Regional Appraisal of Mineral Materials: Carson City District, BLM." The report was authored by real-estate appraisers. It contains more than 50 references to leases of various construction materials in Nevada and nearby states. It gives a thumbnail sketch of each lease and is a good reference. However, the authors erroneously imply that the royalty rate and the in-place value are the same. Several of this year&apos;s new entries come from the report. However, the royalties for landscaping materials vary from state to state and by rock type. Some boulders used for landscaping in Nevada have a royalty reported at $1.10/t ($1/st). At the other extreme is lava from Idaho. Used for the same purpose, it has a royalty range of $11 to $18.70/t ($10 to $17/st). Chuanming Tian of Beijing, China has shared some information about the changing mineral royalty policies in China. China first implemented an oil and gas royalty in 1984. In 1992, the government expanded that to include iron ore. In 1994, the royalty policy was extended to all mineral commodities. At the same time, the royalty rate for iron ore increased tenfold.

Jan 1, 1995

By Robert F. Baker

Neanderthal technology is a harsh and inaccurate way to describe modern underground construction and mining practices, but such an exaggeration helps to focus on a major problem or wasted opportunity of modern society. Why is it not safer to excavate in the underground? Why are the working conditions still so unfavorable? Why are urban freeways, shopping malls, warehouses, power plants, sewage disposal treatment plants, and similar facilities still constructed on the surface of the ground--because it is a better location? On the contrary, if underground technology made full use of existing knowledge, underground resources and space would be much more effectively used. And why is the technology so inadequate? Certainly, researchers and practitioners are aware of the shortcomings and are equally aware of problems that have to be overcome. One of the most important reasons has to do with the type of policy goals that society has set in the past. Policy makers may have agreed that improvements would be desirable but no serious commitments have been made--that is, there has been no major allocation of resources to advance these technologies. And yet, to bring about significant changes will require significant time and resources. The resources that are needed are far in excess of what industry can afford to invest, particularly since the pay-off may be far in the future. So the problem reverts to society in general. As long as society is willing to tolerate the present costs and safety requirements for recovering minerals and for constructing underground facilities, then the changes will be slow in coming. Until such time as society sees and desires the benefits

Jan 1, 1974

By Howard L. Hartman

To concede that I am the most surprised - not to mention the least likely - recipient of the Daniel C. Jackling Award is a true confession I must share with you. Quite honestly, I&apos;ve asked myself, "Why me?" The Jackling Award has a well-deserved reputation of being a practitioner&apos;s, a doer&apos;s, a CEO&apos;s award - not kudos for a retired school teacher! While at least five of the previous recipients have taught in universities, to my knowledge I am the first to earn the award for "alleged" academic accomplishments. It is humbling enough to keep me livable for a long time. If you glance over the roster of Jackling Award lecture topics, you will spot another anomaly: The lectures last year and this deal with the subject of education - the only two in the 37-year history of the award. The two complement one another rather well, too, C. Allen Bom of Amax addressing critical needs of public education, while I am going to look at the post-high-school years. But I want to focus on more than engineering education. The training role of industry - the principal consumer of our product-also warrants examination. As I hope to establish, there is something unique about mining engineering - education and practice - that is both strength and weakness. We need to recognize that, if we are to cope with the weaknesses in order to capitalize on the strengths. We look at five premises that relate to the uniqueness of the mining engineer and his or her preparation for a professional career.

Jan 1, 1991

By V. A. L. Breguncci, A. H. Martins, C. P. Ribeiro Jr.

This work presents experimental results for the recovery of gold present in alkaline cyanide solutions by using the electroelution technique of strong-base anionic polymeric resins IRA 402-CL from Rhom and Haas-Brazil Ltd. loaded with gold. This technique of electroelution of anionic polymeric resins is based on the removal of metal ions adsorbed to the resin, resulting from a potential difference applied between the cathode and anode in an electrolytic cell. The electrolytic cell was composed of an aqueous solution with suitable chemical characteristics and an anionic polymeric resin bed loaded with gold. The resin used in the experiments was loaded using synthetic alkaline gold cyanide solution with 1.0 g/L of gold. The variables studied were electroelution time, cathode current density, distance between cathode and anode and the electrolyte chemical composition. Statistical methods made it possible to establish the optimum conditions that would achieve satisfactory gold recoveries by the electroelution technique. The statistically predicted response for the resin loaded with gold by percolation was 16.5% gold recovery, 2.0 A/m2 cathode current density, 20-mm distance between electrodes and 6.0 hrs electroelution time. For the centrifuging system, the statistically predicted response was 7.41% gold recovery under the following conditions: 0.25 A/m2 cathode current density, 1-mm distance between electrodes, 3.5 hrs electroelution time and 10.9% NaOH in the electrolyte chemical composition.

Jan 1, 2002