Search Documents

By Safdar A. Gill

The technique of installing small diameter caissons (drilled piers) through soft clays and water bearing ganular soil is well established for constructing building foundations. Over the past few years, the method has been utilized for constructing a large number of shafts extending into rock for the Chicago's Deep Tunnel Project. This paper will discuss design considerations for obtaining the most economic ground support system, the impact of construction procedures on the support and lateral pressures for design. Construction procedures will be described along with performance of the shafts.

Jan 1, 1981

By S. J. Jung, F. Lock

This research came about because of the recognized need for a safe, easy way to line small-diameter bored raises (less than 150 cm). Currently, an operator must go down the raise and apply the concrete lining manually, using the shotcrete method of application. With an automated system, there would be no man positioned in the bore itself. All control functions could be commanded from a central location. Shotcreting in the confined space of a small-diameter bored raise presents problems that can be overcome by the application of shotcrete using a remote system.

Jan 1, 1995

By Mengxiong Guo, Xuxin Shao, Yong Bao

In the paper, the adsorption properties of dissolved ions on the surface of collophane and dolomite are studied using zeta potential measurement, ESCA and UV adsorption spectrum both in distilled water and in the supernatant of each other. The effect of dissolved ions on the flotation separation of collophane and dolomite under SCO depressant and oleate is discussed on the basis of above analyses.

Jan 1, 1993

By O. E. Etheridge Jr., R. A. Lowe, C. I. Basilio, J. M. Randolph, S. W. Sheppard

The low-shear viscosity of kaolin slurries is one of the principal characteristics that determine whether a clay can be utilized for paper and ceramic applications. In this work, the causes of high low-shear viscosity and methods for improving the rheological behavior of the slurries were investigated. The presence of fine-grained smectite impurities within the kaolin was shown to detrimentally affect the low-shear rheology of the slurries produced from these clays. It was also shown that mechanically working (i.e., pugging) a crude kaolin followed by desliming to remove these impurities can reduce the low-shear viscosity.

Jan 1, 2000

By A. A. Sonntag, I. Szanto, D. A. Goodman

This paper presents the most recent developments in mixer-settler technology directed towards treating higher throughputs, increasing efficiencies and providing further improvement in SX technology with a new concept: the submerged launder. Industrial plants built in the last past few years and using these improvements are described.

Jan 1, 1993

By Don L. Jensen

With the successful implementation of supervisory control on the Bagdad concentrator grinding circuits, steps have been taken to expand supervisory control to the flotation circuits. This paper discusses the design and installation of the slurry delivery systems, analyzing instruments, level control devices, reagent pumps and supervisory software. Emphasis is placed on the design and installation of a reliable slurry transport system to feed the Courier 30 online analyzing instruments. Total system availability has been measured at plus 95%. Phase 1 acceptance testing of the supervisory software indicates a notable increase in copper recovery with no significant change in final copper grade.

Jan 1, 1999

By Lawrence A. Ph. D. Hansen, J. David Deatherage

Laboratory testing programs were conducted to investigate the performance under compression loading of several types of geomembranes and geotextiles proposed for use in heap and dump leach projects. Synthetic liners of several thicknesses were sandwiched between representative subgrade soils and cover materials, thus modeling in the laboratory the actual installation conditions expected. Performance was evaluated by visual inspection and vacuum testing. Several testing procedures and equipment were used to investigate the effect of these testing parameters on the predicted performance.

Jan 1, 1987

By Waclaw Dziurzynski, Janusz Tracz, Danny Wooton, Andrzej M. Wala

The purpose of this paper is to present validation studies of the mine-fire simulator using data gathered from an actual mine fire which occurred in November 1991 at the Pattiki Mine. This study evaluates the suitability of the computer software package for modeling underground fires. The paper also discusses the importance of the on-line monitoring system for the validation process.

Jan 1, 1995

By R. B. Inturi, R. G. Reddy

Solid-state reduction of roast Movat chromite ore with carbon was carried out as a function of the C/FeO ratio at temperatures ranging from 800°C to 900°C. The reduction was studied using thermogravimetric analysis (TGA). A two¬stage mechanism consisting of the reduction of FeO with carbon monoxide and the regeneration of CO by the oxida¬tion of carbon with CO2 was proposed. The rate-controlling step is the carbon oxidation reaction. A kinetic equation, that of random nucleation, was proposed. The activation energy for the reduction was determined to be 55,800 J/mole and is compared to those activation energies determined for other chromite ores.

Jan 1, 2000

Health and safety issues are very important to the mining industry. Although the application of scientific research and current technology shields workers from many dangerous aspects of mining, accidents do happen. Many companies and institutions worldwide have committed to a continuous effort to minimize such occurrences. In this study, the health and safety data pertaining to the Greek mining and quarrying industry for the last three decades are presented and critically evaluated with respect to factors such as the number of workers and annual production. Appropriate indices are also calculated regarding the incidence and frequency of accidents. Health and safety issues specific to mining in Greece are also discussed.

Jan 1, 2002

By James A. Morrison, Stephane Carayol, Paul H. Madsen

The Rio Piedras Alignment Section 7 of the Tren Urbano is currently being constructed beneath a historic commercial section of San Juan. Different portions of the section are being constructed using open cut, cut-and-cover, New Austrian Tunneling Method (NATM), Earth Pressure Balance Machine (EPBM), and as tacked drift mined support system. The combination of complex geology, low ground cover, and several innovative construction methods present many challenges to the ground control program. Mining and construction sequences were first developed to minimize ground movements and risk of damage to structures. A unique compensation-grouting program was developed to improve the ground, limit settlement, and recover settlements incurred due to mining.

Jan 1, 1999

By H. Lyn Bourne

The is the 13th year for this column and the 12th in which the royalty data have been tabulated. There still exist some holes in the list of royalties that readers hopefully will fill. The most common mineral commodity is construction aggregates - either sand and gravel or crushed stone. In spite of their pervasive use nationwide, there are states from which the author has no information about royalties for either of these commodities. The reader can help - share information about these missing states and next year there will be fewer states without information. Severn Brown again sends helpful information from the Prospectors and Developers Association of Canada (PDAC). The PDAC Digest contained an article that distinguished between ‘net smelter return royalty' and ‘net profits royalty’ (Haase). The article also lists clauses and details that Brown suggests should be included in a net profits royalty contract.

Jan 1, 1994

By G. R. Wheeler

Epithermal gold exploration in the last decade has developed useful models for exploring previously overlooked ore districts in Oregon. In eastern Oregon, disseminated gold occurs in epithermal deposits that have been pervasively silicified and brecciated. Many gold prospects staked since 1980 are in fluvial and lacustrine sandstone and conglomerate deposits. Clay alteration products and disseminated pyrite may be present. Vein filling calcite and thin to thick quartz veins are common. Late stage quartz forms pseudomorphs after calcite in many prospects. Arsenic, mercury, and gold are geochemically anomalous but silver is usually not. The epithermal deposits are located in part of the Deer Butte formation or equivalent units. Exploration criteria include the presence -of Deer Butte formation or equivalent units and northwest structures cut by north-south basin and range structures.

Jan 1, 1987

By Veliko Kertikov

Complicated processes of heat exchange and evaporation, leading to changes in the temperature and humidity of the ventilating air flow, take place during the driving of headings. In the case when virgin rock temperature is high, the increase in air temperature and humidity is significant. This causes a deterioration of climatic conditions in the headings. Procedures for predicting the changes in air temperature and humidity are discussed, together with appropriate calculations and computer programmes. Predicted results for example scenarios are used as a background for the selection of approaches and means to improve the climatic conditions in a dead-end heading using auxiliary ventilation.

Jan 1, 1997

By Dean J. Soderstrom

Soil and sands were contaminated with depleted uranium from weapons testing. This resulted in the formation of a complex mixture of uranium compounds. Characterization studies of the soil indicated the uranium was present as uranium metal, uranium oxides, silicon-bearing metallic uranium, and uranium silicates. A process was developed to selectively remove dense uranium compounds using gravity separation and a chemical extraction system to remove uranium which was not available for separation by gravity methods. Results from characterization studies and pilot scale testing are presented for background information. The primary purpose of this presentation is the report of the results achieved in the field application of the processes.

Jan 1, 1995

By D. A. Knight, V. G. Medina

Kidston's 14 000 t/d mine and mill complex in Queensland, Australia, started operation in January 1985. During its first 18 months of operation, the mine produced over 7000 kg (225,000 oz) of gold, making it the largest gold producer in Australia. This paper describes the planning, logistics, flowsheet, and process for the Kidston project, and some of the problems encountered during startup and the measures taken to correct these problems.

Jan 1, 1987

By Barry T. Kilbourn

Yttrium Oxide is versatile; it is essential for television phosphors, for microwave garnets, for laser crystals and for high-performance ceramics, to name but a few advanced applications. When produced commercially, the material must satisfy not only stringent specifications regarding chemical purity but, increasingly, also meet closely defined physical parameters. The techniques needed for its production range from solvent extraction to carefully controlled precipitation and calcination. The processing steps from mineral concentrate to pure oxide will be described and related to the final oxide. The simple word "material" has complex connotations; it means, to paraphrase "Alice", exactly what we want it to mean. Throw in the label "advanced" and the picture darkens further! Just what is an advanced material and how does it differ from a common-or-garden material?

Jan 1, 1990

By Allan E. Koski

Michigan is the second largest iron ore producing state in the United States. The Empire Mine, celebrating its 30th anniversary in 1994, is the largest iron ore mine in the state. The Empire Iron Mining Partnership is an iron ore mining, concentrating and pelletizing facility managed by The Cleveland-Cliffs Iron Co., a subsidiary of Cleveland-Cliffs Inc. The Empire Mine is located near Palmer, MI on the Marquette Iron Range in Michigan's Upper Peninsula. The partnership includes Inland Steel Co., LTV Steel Co., Wheeling-Pittsburgh Steel Corp. and Cleveland-Cliffs. Mine construction began in 1960. The first pellets were produced in late 1963. Successive expansions in 1967, 1974 and 1979 resulted in Empire reaching a present annual capacity of 8.1 Mt (8 million long tons) of pellets. In late 1993, a milestone was reached with the production of Empire's 152-Mt (150-millionth long ton) of iron ore pellets.

Jan 1, 1994

By Steve Van Kouteren

Filters and absorbents purify, clarify, and clean many types of liquids by removing solid particles. In addition, absorbents provide a convenient way to handle liquids and to clean up liquid wastes or spills. Filtration or absorptive processes are accomplished either in a mechanical way, as in absorption and filtration, or in a chemical way, as in adsorption. In filtration, minerals and rocks used as filter mediums are extensively utilized in applications requiring the filtration of high volumes of liquids. End use applications include liquid food products, waste waters, petroleum and chemicals, and drugs and pharmaceuticals. Upon closer examination of all of the materials used as filters and absorbents, industrial minerals and rocks represent only a small proportion of the total amount, as shown in [Fig. 1] (Rees, 1991). Given all the industries that use these minerals, most of the volume is concentrated in a few major end-use markets. Within these major end-use markets, a handful of minerals account for most of the total volume and value. The focus for this chapter will be to discuss the industrial minerals and rocks used as filters and absorbents in the most important markets. The selection of the minerals and markets to review is solely based on the total volume of material used and in special cases, those where the value of the market and material is high. The major materials include diatomite, perlite, sand, gravel, and such specialty clays as montmorillonite and attapulgite. These materials are mainly used for the filtration of food, chemical, and petroleum products. In addition, they are used as absorbents for pet litter and oil and grease spills, and as carriers for pesticides and fertilizers.

Jan 1, 1994

By Anna Marabini

This paper provides a summary of the studies performed over a period of more than fifteen years by the Italian National Research Council's Mineral Processing Institute in Rome to develop applications for the use of chelating reagents in the flotation of metallic minerals. A description is given of the various phases through which the studied progressed, starting with the combined use of commercial chelating reagents and a neutral oil and then moving on to the synthesis of new long-chain chelate collectors for the flotation of sulphide and oxidized Pb, Zn and Cu minerals. After a series of preliminary tests which confirmed the possibility of floating various metallic minerals with commercial reagents containing chelating groups exerting specific action on given cations, the studies were addressed to the development of a theoretical method of choosing chelating groups that exert selective action on one metallic mineral rather than others. The theoretical approach was based on thermodynamic data concerning the chemical equilibria in solution. The validity of the method has been proved in numerous cases by flotation tests on pure minerals. Subsequently the research was directed towards the design and synthesis of reagents with a mixed aliphatic-aromatic structure containing chelating groups for Pb and Zn and an alcoxyl chain of various length, position and configuration. The flotation results obtained on oxidized and mixed Zn-Pb ores provided interesting pointers for designing the nonpolar portion. The structural criteria identified via these studies were interpreted on the basis of chemical and steric considerations. A description is given of a new synthetic chelate collector which is effective in the selective flotation of Cu minerals from complex sulphides. The fact that this reagents is more selective than xanthate is demonstrated by comparative flotation tests on actual ores.

Jan 1, 1994