Search Documents

By K. R. Weller, U. J. Sterns

The goal of most in-plant studies is to identify factors that limit overall plant performance. A major finding from such studies is that interactions between unit operations are always important, usually specific for a particular ore and plant combination, and are one of the limits to plant performance. Computer simulation based on process models developed from in-plant studies is a useful tool for identifying limits to performance and for estimating the effects of proposed changes at both pilot and industrial plant scales. Examples involving interactions between comminution and various separation and agglomeration processes are presented, and directions for future development discussed.

Jan 1, 1989

By James L. Noble

A small placer operation can be defined as one with a throughput capacity of 250 cubic yards an hour or less. The success of small placer operations after the values have been established, depend entirely on having the proper design. There are various types of placer deposits including marine, beach, desert, stream, bench, underground and even frozen placers. Each is unique and requires special considerations. Size distribution of alluvial placer ore varies from sand to large boulders. When boulders occur, they can become a problem to all types of excavating to a greater or lesser degree. Clay content and cementing are common in placer deposits. Some clay disperses easily in water while others, if not handled properly, will form clay balls that pick up gold and carry it to tailings. Overburden, depth of bedrock, vegetation, and ground and surface water must all be considered when designing a plant. Any equipment chosen should be capable of processing large volumes of material at a high efficiency. There are usually five steps to processing placer gravels, as follows:

Jan 1, 1992

By D. J. Kennedy, W. G. Klinowski

Over the past few years the Cape Breton Coal Research Laboratory's staff designed, built, tested and proved the necessary hardware, software and methodology of tracer gas based surveying techniques applied in the field of mine ventilation. These methods are now used routinely in a variety of applications where traditional anemometric methods do not provide the required accuracies or cannot be effectively employed. Irregular or highly turbulent flows, leakages, geometrically complicated or highly obstructed airways are just a few examples where traditional anemometry can produce unacceptable errors in calculated ventilation parameters. Tracer gas based ventilation techniques have been used in many problematic situations where the standard ventilation methods are inadequate. One such problem, faced by many mine operators, is the emergency imposed by the ever present threat of a mine fire. An understanding of the propagation of smoke contaminants and the demonstrated integrity of appointed escape routes can save lives and property during a fire. That knowledge can be gained quickly and inexpensively by the application of tracer gas smoke simulation methods. The concept of controlled air recirculation has recently gained considerable attention in the mining industry. While mathematical models can be used to predict performance, the ultimate proof of a ventilation system's performance can best be provided by a tracer gas based simulation of contaminant levels. Fan performance tests and assessment of auxiliary ventilation systems are highly dependent on accurate definition of airflows; precise data can be easily obtained by tracer gas based volumetric surveys. This paper contains a brief description of the equipment and the methodology of tracer gas based ventilation techniques and presents typical examples of their use

Jan 1, 1991

By G. R. Tostengard

Gold plant performance during the start-up period, which extends until capacity production is sustained, has a major impact on the internal rate of return and the net present value of gold projects regardless of mining and processing configurations. The start-up period experiences substandard production, extra expenses, and sometimes reduced recovery. This results in lost profits, a portion of which are recouped at the end of the life of the mine. Poor start-up performance can put projects into financial jeopardy. The gold mining industry regularly experiences start-ups ranging from good to poor. Problem areas, which affect start-up performance, include shortcomings in ore reserve sampling and testing, equipment design and installation, untrained plant operators, inability to cope with problems which arise, and organization of the maintenance program. An investment, equal to 0.5% to 1.0% of plant capital cost, in programs to prepare for start-up, in advance, is recommended. Investment in such a program will make a good start-up possible. Without it the best result which can normally be expected is a fair start-up. Developers of new gold mines are urged to compare the cost of this investment with the anticipated increase in project net present value. Funds for this investment should be included in feasibility studies.

Jan 1, 1988

By J. Y. Hwang, M. L. Jeong, R. C. Greenlund

Various aluminum-smelting by-products from three production sources were received and characterized. The waste materials were tested for compound identification and environmental acceptance. A coarse metallic aluminum recovery test using an Eddy Current separator (ECS) was performed using two different Circuit configurations. White dross performed equally well with either Circuit, while black dross processing shows significant difference on the separation results. It was found that ECS technology was effective for particle sizes down to 6-10 mesh.

Jan 1, 2001

By A. F. Stewart

Slope design in an open pit mine includes the determination of a number of parameters, including bench height, bench face angle and berm width. By way of a case history of two highwall slopes (160m and 220m high) excavated in dipping strata in an operating coal mine, this paper illustrates the influence that bench face angle can have on the stability of an entire slope. The two highwall slopes, the lower of which experienced significant instability, were excavated in essentially the same lithologic and structural environment, with the main differences between the slopes being the angle at which the bench faces were excavated and the excavating methods that were employed. In addition to describing the instability that occurred on one of the pit walls, relevant aspects of the engineering geology, slope design and excavation procedures are described.

Jan 1, 1998

By M. R. Stokes, A. J. Ross

As a result of higher levels of production and greater depths the underground mining industry in the UK is encountering hotter climates in some workplaces. It is widely known that high heat and humidity in an underground workplace will result in reduced performance and may also seriously impair the health and safety of the workforce. It is therefore of paramount importance that the underground environment can be effectively predicted in order that sound decisions can be made to reduce the effect of climate on working personnel. Over the years numerous computer programs have been developed to predict the climate in underground mines. One such important program, developed by McPherson, is CLlMSlM TM which is a prediction model of heat and mass transfer along a single roadway. This paper describes the development of a computer model, called DRIVE, to predict the climate in single entry drivages. This program incorporates the theory established by McPherson for the development of CLlMSlM TM. This involves the algorithm for unsteady state heat transfer. Throughout the development of DRIVE underground measurements have been taken to correlate the program. DRIVE will predict the changes in psychrometric and thermo- dynamic conditions along the drivage depending on a number of parameters. Firstly, the type of auxiliary ventilation system employed such as forcing, exhausting, overlap. Secondly, the addition of heat and moisture due to autocompression, machinery, strata, fissure water, oxidation, broken rock, fallen rock, refrigeration equipment, lighting, personnel, service water. Thirdly, due to the velocity of the air.

Jan 1, 1997

By Y. C. Kim, W. L. Meyer, W. Cai

Although the first published optimum pit limit design algorithm by Lerchs-Grossmann dates back to 1965, the majority of the open-pit mines in the US has not as yet adopted such a rigorous optimization algorithm. Instead, the floating cone approach initially developed by Kennecott Copper in 1961 is still used today for various reasons. However, shortcomings with the floating cone algorithm, particularly for precious metal deposits with erratic mineral distributions, have provided a renewed interest in optimizing algorithms. This paper compares the performance of the floating cone algorithm with the rigorous optimization algorithm of the Lerchs-Grossman's graph theory and the newly developed maximum network flow algorithm by Hanson (1986). The maximum flow algorithm is a modified version of the logic as initially advocated by Johnson in 1968. Comparisons are made for three different deposits in terms of the total profits generated and the computation times involved. The results of the comparison show that both algorithms produced higher total profitability pits than the floating cone in all three deposits, although the increase in profits never exceeded 1 % of the base design obtained using the floating cone. Between the graph theory and maximum flow, graph theory produced consistently higher profits. The current version of maximum flow, however, cannot be modified to produce the optimum pit. Nevertheless, the authors prefer the maximum flow over the graph theory, simply because it is easy to program as well as to explain.

Jan 1, 1987

By Osvaldo Bascur

Large metallurgical complexes have more data than a small city and much of it is "real time," changing rapidly as internal and external conditions evolve. As corporations buy and sell assets and reengineer their staff, the structures and tools that were used to understand these data are lost. This results in significant deterioration in the ability to maintain a "smart" operation. The solution is to use the sophisticated new tools built for the Internet so as to leverage information in a familiar browser format that people can use and understand. This paper describes the use of Internet technologies with plant data. Examples are drawn from existing industrial sites. Users must project where this technology will lead - standing still is the most dangerous philosophy and the only one guaranteed to be obsolete. These examples show the way to leverage existing workers with information technology.

Jan 1, 2000

By Clete Stephan, John Urosek, Ian Anderson

The Endeavour Colliery is operated by Powercoal Pty Ltd. It is located in the Central Coast of New South Wales, Australia. The mine has been in operation for about 30 years, producing around 600,000 tons of export coal annually from two production sections. On June 28. 1995, an explosion occurred underground in the 300 Panel at approximately 9:50 a.m.. There were thirty miners underground at the time of the explosion, all of whom were safely evacuated. From June 29 through July 10, personnel did not enter the mine. However, gas samples of the mine atmosphere were obtained from underground monitoring stations and analyzed. Samples were also obtained from boreholes that were drilled from an adjacent mine. On July 10, the atmosphere at the underground monitoring locations and at the boreholes appeared stable with minimal risk of combustion occurring underground. Plans were developed to begin the recovery of the underground workings. The recovery of the underground workings was completed on July 13. The underground investigation of the explosion began on July 14. The investigation was conducted by the New South Wales Department of Mineral Resources. Technical assistance was pro- vided by the United States Department of Labor's Mine Safety and Health Administration (MSHA).

Jan 1, 1997

By Richard D. Harvey

Relative quantitative analyses of certain mineralogical and textural properties of carbonate rocks were made with an image analysis computer. The instrument, referred to by its manufacturer as a Quantimet; consists of a petrographic microscope, a television camera and monitor, a detector, an electronic computer, and a read-out meter. Measurements were made on polished and etched specimens, standard thin sections, and on scanning electron micrographs of carbonate rocks. Critical to the success of the analysis is the preparation of the specimen in such a way that good optical contrast is obtained between the various petrographic components. The dolomite content, the pore volume, pore boundary projection, and pore size distribution of high-purity carbonate rocks were measured by image analysis methods. The frequency and size distribution of void inclusions in dolomites were determined by image analysis of scanning electron micrographs of cleaved surfaces. Image analysis methods permit rapid and quantitative assessment of various microscopic properties. The results are of reasonable accuracy and certainly are relative quantities that may be used to characterize carbonate rock materials.

Jan 1, 1972

By Betty L. Gibbs

Computer software for mining applications has been in development since before 1970. These packages cover tasks from exploration data management through final reclamation planning. These programs were originally written in Fortran and have evolved into colorful, user-friendly packages. Programs that produced printed symbol maps now show color, three-dimensional image of an ore deposit on a computer screen. Pictures can be rotated and looked at it from all directions and layers can be peeled off to show other parts of a model. Computer users have also evolved. In the early Fortran days, users had to learn computer operating systems, have someone punch data cards, set up run files and wait a day or so to find out if there was one little mistake somewhere that caused the program not to run. With today's technology, users sit at their desks in the office, key in some data, read other data from digital files and build a model within days, rather than weeks or months.

Jan 1, 1999

By A. Shah, L. W. Saperstein, M. C. Radomsky, D. L. Passmore

The development of microcomputer software that provides an analysis of pit-specific accident and production data for the mining industry is seen as a vital component in a total loss-control system. The Mine Injury Reporting System (MIRS) allows users to access accident and production data prepared by the Health and Safety Technology Center of the Mine Safety and Health Administration of the US Department of Labor for any particular state and to generate a simple, yet informative, report.

Jan 1, 1990

By Ahmed A. El-Saie

To reduce the problem of overbreak and its associated added costs, a new technique is proposed to make a slot around the tunnel profile in hard rock. The Finite Element Method was used to investigate the effect of the slot on the stress field and deflection of the tunnel core. Beam theory was also applied to calculate the stresses and deflections of a slotted tunnel for several different slot depths.

Jan 1, 1981

By Gregg E. Korbin, Patrick Hamilton

INTRODUCTION The Balsam Meadow Project, presently under construction for the Southern California Edison Company, is located approximately 55 miles northeast of Fresno, in the Sierra Nevada Mountains (Fig. 1). Major components of this project include an underground powerhouse for a 200 MW unit and a high pressure power tunnel/shaft. Site exploration [ ]

Jan 1, 1987

By Hans Skretting, Abraham A. Dor

This paper briefly reviews the historical development of the Rotary Kiln-Electric Furnace Process, which was first applied commercially to the treatment of qarnieritic ores in New Caledonia in the mid-fifties. It describes various technological improvements introduced, since, in industrial plants or developed in pilot facilities where a wide variety of nickel oxide ores has been treated success- fully over the years. Major categories of ores are characterized. The effect of their physical and chemical properties on their performance in the electric furnace is discussed. The relationships between ore composition, ferronickel grade and slag composition are analyzed and their effect on slag and metal tapping temperatures, nickel recovery, and electrode voltage are discussed.

Jan 1, 1979

By S. K. Mishra, S. B. Kanungo, D. Biswal

Jigging of the -2.8 +0.7-mm size fraction of a friable, low-grade manganese ore sample from Andhra Pradesh increased the Mn content of a concentrate by 7% to 8%, with an average recovery of 57%. The jig concentrate was mixed with the unjigged -0.7-mm size fraction and ground to -150 µm. The sample was then subjected to wet high-intensity magnetic separation (WHIMS). The magnetic fraction thus obtained showed an increase in Mn content of 6%, but with an overall recovery of only 50%. The results of hydrocyclone classification of -150- µm ground ore indicated that the method is not capable of upgrading the manganese content, as both ferromanganese oxides and aluminosilicate gangue minerals constitute the fine size fraction. However, when the nonmagnetic fraction obtained from the WHIMS of -150- µm ore is subjected to hydrocyclone classification and the underflow obtained is subjected to WHIMS again, an overall recovery of about 50% to 52% is obtained with at least a 7% to 8% increase in the Mn content of the product. The phosphorus content in the product is not reduced by either of the two combinations of methods. The complex association of phosphorus with all the major phases in the ore has been clearly demonstrated from the linear correlation between the distribution ratios of major constituent phases and phosphorus.

Jan 1, 2000

By P. Diehl

The increasing public interest in a useful framework for an assessment and classification of mineral resources (1) is documented by the recently published international classification scheme of the United Nations (1979) and the revision of the classification system of USBM/USGS (2) (1980). Moreover, various classification systems are currently discussed by the mining industry. In spite of major improvements in respect of the concepts, definitions, and taxonomy of ore classification, it has been recognized that the recent practice to classify mineral resources does not create truly reproductible results, i.e. an assessment to the various categories which is free from personal bias or corporate interests. Following are geostatistical methods proposed for a standardization and quantification of various terms in ore classification. After critical review of present practices, we will establish a precise link between the classical terms such as "measured", "indicated", and "inferred" reserves and the geostatistical concept of estimation errors. Moreover, we will demonstrate, how the basic criteria of economic feasibility, geologic assurance and recovery can be taken into account by geostatistics. A specific algorithm will be proposed to block out and to classify reserves according to the degree of geologic assurance. . We will also show computerized methods which perform complete classification procedures, and will also exemplify them with typical case studies.

Jan 1, 1982

By E. T. Sugar

English China Clays, the world's largest producer of China Clay, has its main production capacity in the South-West of England, where a complex of pits, refining plants, dryers and ports covers an area of approximately 100 square kilometres. The possibility of a computerised information network was first considered in 1980. The system was required to provide information at the central level and also at local plant level to improve co-ordination and control. Immediate access by any authorised user, and flexibility of interrogation were important aims. A small micro-based prototype system was implemented in 1981, and later that year development of the mainframe system commenced. This latter system will provide at least one terminal in every works location and will allow inter-communication of laboratory test data as well as detailed stock levels and production data. An integrated system for order processing will allow stock levels to be monitored in relation to anticipated requirements. The system has been developed by the Data Processing Department using the IDMS database package running on an ICL ME29 mainframe. It was decided to use microcomputers as terminals, which although more complicated because of protocol emulation allows stand-alone applications to be run on the same equipment. Those applications concerning Production Planning are outlined in the paper. Communication on the network is by synchronous transmission over dedicated lines. All data is stored on the central database with terminals accessing it in a star configuration. The system is currently partially implemented with 30 available screens at 18 separate worksites.

Jan 1, 1986

By K. J. Stanaway

Environmental pressures on waste disposal are forcing pigment producers to use feedstocks with higher Ti02 content and lower levels of trace elements. Despite this, 50% of the world's Ti02 comes from ilmenite concentrates with only 37% to 54% Ti02. An industry growth rate of 25% in the next 10 years, combined with trends to diminishing resources and lower mining grades for rutile (95% P02) and leucoxenized ilmenite (55% to 90% P02), means that unless new discoveries are made soon, the industry will become even more reliant on ilmenite.

Jan 1, 1995