Search Documents

By J. Yordan, J. Zinterer

Effective removal of ink particles by froth flotation is of up-most importance in paper recycling. In this study, the potential use of talc particles as carriers of difficult-to-float fine ink particles is investigated. In order to accomplish ink particles removal, the interactions between talc and oily- ink particles in aqueous solutions containing flotation chemicals was studied by zeta potential distribution measurements and with the impinging jet apparatus. The chemical conditions under which talc-ink adhesion occurs are identified and reported.

Jan 1, 2003

By S. Bhattacharya, M. M. Singh

The Surface Mining Control and Reclamation Act of 1977 (SMCRA) requires under-ground coal mine operations to prevent "material damage" to renewable resource lands caused by subsidence. However, what constitutes material damage is not defined. This paper discusses the applicable criteria for agricultural lands, forests and grazing lands, surface water bodies, and ground water aquifers. Although data on the subject are limited, an attempt is made to present quantitative guidelines to distinguish between moderate and severe damage due to subsidence.

Jan 1, 1988

By R. K. Mehta, U. Cetin

The Nevada Test Site is located approximately 100 km (65 miles) northwest of Las Vegas, NV. The site was primarily used by the Department of Energy for the field testing of nuclear weapons and has been contaminated by several million cubic feet of low-level radioactive wastes, heavy metals, explosive materials, and volatile and nonvolatile organics. The transportation and leaching of these contaminants are creating serious environmental problems. The purpose of this study is to examine pozzolan, a natural alumina-silicate mineral, as a possible replacement for the existing impermeable clay barriers. In the first phase of this study, radionuclide sorption characteristics of pozzolan were investigated. This paper presents the results of the adsorption tests for the target radionuclides.

Jan 1, 2000

By J. C. May, G. M. Elliott, J. J. Brady

Increased clearance was required in two railroad tunnels that were built about the time of the Civil War. Clearance infringements, whether they be excavation tights or caused by ice accumulation, reduce tunnel serviceability. Achieving increased clearance often means disturbing the ground and old ground support structures. Access and transportation needs dictate how and when the work can be carried out, and strongly influence the design approach and the methods used by the contractor to execute the work. This paper explores the pertinent considerations of the owner, the designer, the field inspection team, and the contractor in bringing this project to a successful conclusion.

Jan 1, 1997

By Eric Forssberg, Benny Andreasson

The paper describes experiments to stabilize mineral processing waste materials for use in construction. Fine mineral processing wastes from various mines have been mixed with binders and compacted. As binders blast furnace slag and other materials have been used. Experiments have been made in laboratory scale and in large scale. The results have been evaluated by means of determinations of compression strength and the modulus of elasticity. The paper also describes some experiments in laboratory and large scale to use stabilized mineral processing wastes for back filling in cut and fill mining.

Jan 1, 1992

By R. Sawyer, M. Sadler, M. Holdworth

Greens Creek is a high grade Ag/Au/Pb/Zn deposit located in southeast Alaska. Maximizing the Net Smelter Return revenue from the fine grained mineralization is a dynamic process given changes in metal prices, smelting terms, ore grades and flotation characteristics. This paper discusses the evolving concentrate production strategy, and how it is affected by such factors as ore and concentrate specifications and by market conditions. Also described is the development of an on-line computer program that provides the mill operators with real time NSR data and a means for optimizing Net Smelter Return.

Jan 1, 2002

By Y. C. Kim

This paper describes the implementational aspects of a blast hole kriging system that has been developedfor the purpose of daily ore/waste control in an open pit mine. The primary goal of blast hole kriging is to improve the ore/waste delineation procedure. A complete computer program package called Blast Hole Kriging (BHK) System was developed for IBMIPC AT or XT computers, using the Fortran language and supplemented by a few assembly language routines for the bit- map manipulation. This paper emphasizes the practical implementation requirements of the system and discusses system design considerations.

Jan 1, 1991

By Giuseppe Bonifazi

This study examines the problems involved with the control of characteristics of the products resulting from comminution operations. A methodology of investigation based on texture analysis procedures by image processing techniques of the comminution product is proposed. Some examples of applications are considered with particular reference to comminution products of different textural, structural and mechanical characteristics. The advantages and the limites of this method of approach are, indicated, both as regards performance of the investigations and subsequent processing of results.

Jan 1, 1989

By C. Roldan, C. Garcia, J. D. Miller, C. L. Lin

The ultimate recovery in a heap leaching operation is related to the degree of exposure of the valuable minerals in comminuted particles. Recently, high-resolution cone beam x-ray microtomography (XMT) has been used to determine this parameter. XMT technology consists of examining the extent of mineral exposure for each size fraction of ore in 3D, then, by algebraic calculations, the ultimate recovery can be estimated for different particle size distributions (PSD). To confirm the usefulness of the XMT technology for mineral exposure analysis, column tests were performed to determine ultimate recovery using three PSDs for two composites obtained from the copper heap leaching operation at Zaldivar-Chile.

Jan 1, 2003

By R. R. Rollins

Field data combined with theoretical derivations were used to design a surface mining operation using explosive casting. Calculated casting results varied from 44% to 65% depending on bench height. The field tests were performed at an Eastern, contour, coal stripping operation. Results from five experimental casting shots, using a shovel and trucks, are summarized and compared to conventional mining methods. The overburden material removed by casting ranged from 35% to 65%, with an average of 50%. Fragmentation was improved, and it was demonstrated that this procedure is economically attractive, with a resultant cost savings of $0.59/m3 or $5.93/t of clean coal.

Jan 1, 1988

By J. -C. Roegiers, M. Thiercelin

Accurate toughness determinations are difficult to achieve in the case of soft or heterogeneous rocks. The existence of a large process zone ahead of the crack tip makes the determination of the apparent toughness crack length dependent, in the case of subsized specimens. In order to use practical size specimens, the authors propose a new toughness test, the Modified Ring Test, which pre- vents a largely developed process zone to form ahead of the crack tip. This test has also the advantage that its geometry is core-based. Numerical and experimental results are discussed.

Jan 1, 1986

By J. P. McDonnell, L. A. Beckett, K. Y. Hammy

Dangerously high stress areas can be controlled by proper mine planning and/or destressing. This paper reviews practical methods to detect and destress high-stress zones along coal faces. The US Bureau of Mines investigated stress-related burst problems and destressing efforts at a cooperating mine. Laboratory tests of the drilling yield method for high stress detection were conducted to determine the correlation between the volume of cuttings obtained and the magnitude of the applied stress. A three- dimemiom1 computer modeling program was used to evaluate the effectiveness of stress relief methods.

Jan 1, 1987

By M. K. Patel, K. C. Wade, M. Cross

In the past decade a good deal of effort has gone into the computer simulation of the heat distribution of pellet induration systems. The major uncertainty in the analysis of such systems is the gas flow distribution and, in particular, the role of leakage. Evaluation of the leakage into or out of a zone has proved to be very difficult, as has the cross-flow from one zone to another when adjoining zones have gas flows which change direction from up draft to down draft for example. This paper describes an initial model to calculate the gas flow distribution in a variety of practical situations of interest to those involved in pellet induration. The model is based upon a multiphase CFD code called CASCADE which is used in conjunction with the pellet induration simulation INDSYS.

Jan 1, 1990

By T. Malterer, R. Adams

Peat has unique physical, chemical and biological properties. These include high porosity and water retention, high absorption and adsorption properties, and high buffering capacity. In addition, peat is a rich medium for microorganism activity. Peat has traditionally been used for horticultural purposes. However, in recent years, peat is increasingly being used for waste- treatment purposes. This paper reviews North American literature on the use of peat for waste-treatment applications. The literature indicated that peat has potential for use in the treatment of municipal and on-site effluents, for the removal of low concentrations of heavy metals and for the adsorption of liquid and gaseous hydrocarbon pollutants.

Jan 1, 1997

By A. Cavero, M. Diaz

The annual rainfall at Minera Yanacocha's gold mining operations in northern Peru averages 1.2 meters. The influx of water into the operations is higher than losses to evaporation and by ore absorption which results in a positive water balance. To minimize water intake and maintain a balance, some special operating procedures are required, and a system involving diversion ditches, storm ponds, heap skirting and detoxification and treatment of excess water is practiced. An operation background is also reviewed at the beginning of the paper.

Jan 1, 1998

By T. S. Mackey

The industrial types, sources, and quantities of US tin residues are identified and the methods of treatment reviewed. The effect of a lower tin price, due to a current major world surplus of tin metal, is mentioned and covered in some detail. The names and locations of over 100 US firms recovering tin residues are listed. Current smelting and refining charges are included to convert the residues into tin metal and alloy. The impact of the complete with-drawal of the LME daily tin price since Oct. 24, 1985, and the collapse of the International Tin Council, which at one time supported the Buffer Stock Manager, are reported with comments.

Jan 1, 1987

By S. K. Kawatra, T. C. Eisele

A horizontal-baffle arrangement has been developed to prevent excessive axial mixing in flotation columns. These baffles have been shown in previous work to improve the grade/recovery performance of both a laboratory-scale column and a pilot-scale column (Kawatra and Eisele. 1993). In this paper, results are given for continuous on-line operation of the pilot-scale baffled column in a commercial coal- cleaning plant. These results show its ability to operate for extended periods without plugging, to produce a consistent-quality product even while the feed quality was fluctuating, and to remove much of the pyritic sulfur from the coal.

Jan 1, 1995

By Edgardo I. Cifuentes, Andrew L. Mular, Andrew Burkert

Experimental designs are data acquisition plans which, if followed exactly, will quickly provide process engineers with information to assess statistically the individual and joint influence of factors on responses to permit of rapid decision making. Methodology employed to construct data acquisition plans is described in some detail. In production environments, factorial designs are appropriate for most purposes. Use of two level factorials to make decisions is described for a grinding circuit.

Jan 1, 1991

By J. Mark Richardson

Modern mining operations are increasingly affected by complex economic factors. Broad and rapid fluctuations in metal prices, rising operating costs, socio-political trends and the inherent technical difficulties encountered in most operations, all can combine to quickly change once-profitable ventures into money-losing propositions. Accurate knowledge of metal inventories during all phases of an operation has become essential to wise management decision-making. This paper reviews key elements of metallurgical accounting: sampling theory, measurement technology and computerized data adjustment. Application of current technology to the reconciliation of a hypothetical operation is discussed.

Jan 1, 1991

By Ed Van Eeckhout

The rockburst monitoring system at the Sunshine Mine has recently been improved to increase the certainty of burst locations and to output location results in a manner amenable to easy interpretation. Three methods of location calculation were used: a computer code provided with the hardware in-place (the MP-2501, a code based on the least-squares method (Blake et a1, 19741, and a nonlinear iterative code written by the principal author. The more accurate locations are given by the latter two codes, but still are only correct to within about 100 ft. This error is due to uncertainties introduced by the geologic and mining variations versus the assumptions made in the location codes. Software was then written to make two-dimensional plots of burst location by level, so management could monitor problems easily.

Jan 1, 1986