Search Documents

By Gregory A. Hope, Kym Watling, Matthew I. Jeffrey, Ronald Woods

Surface enhanced Raman Spectroscopy carried out in real time has been applied to identify surface species formed during gold leaching in chloride and thiosulfate media. Chloride ion is adsorbed prior to the gold dissolution potential, but its coverage is significantly diminished at the beginning of leaching. A gold chloride band is again observed when dissolution is rapid, together with bands characteristic of AuC14- ions in solution. With thiosulfate, a thin gold sulfide layer is formed slowly in the potential region where leaching occurs. At higher potentials, thiosulfate is oxidized to sulfur and sulfate, both products being identified by Raman spectroscopy.

Jan 1, 2005

By Fabio Amaya, Andrés Marulanda, Ramiro Gutiérrez, Alberto Marulanda

The behavior of a salt rock mass is strongly related to a creep phenomenon. The amount of creep depends on the level of stress generated in the underground excavation. Additionally, security conditions and the lifespan of an underground cavern excavated under this geological conditions depend on the evolution of creep. Based on the experience of the failure of the Old Underground Salt Cathedral of Zipaquirá(Colombia) and the construction of the new one, the theoretical framework to predict the creep behavior of a salt rock mass is explained. The theoretical formulations are calibrated based on actual observations of the material behavior to predict the lifespan of this striking structure.

Jan 1, 2003

By E. Woodburn, R. P. King, R. Putman

Flotation plant simulation, a relatively recent methodology in mineral processing, is defined and corresponding uses are discussed. Typical simulation structures are compared. Current problem areas exist although these are not insurmountable. Following a brief state of the art discussion, the N. I. M. simulation program is reviewed. In general, digital plant simulation is expected to be of substantial benefit in the near future.

Jan 1, 1976

By Richard Crawshay, Duncan Hutchison

Continuous Mining Systems Limited have developed an efficient, high-capacity, in-line loading unit capable of handling shot rock in tunnel driveages at extraction rates up to 970 tonnes (1,000 tons) per hour. A smaller 408 tonnes (450 tons) per hour loader is also available These in-line loading units called "Osciloaders"® provide a continuous flow of material from the muck pile to an anciliary conveyance eliminating the cyclic or interrupted movement noramlly associated with gathering arm or bucket type loaders. The osillating lip fluidizes the material, reduces the penetration force required and facilitates and regulates the material flow onto the adjacent conveyor. The conveyor is wide and accommodates very large material with ease, transporting and elevating it to a height suitable for a waiting conveyance at the rear of the machine. The "Osciloader"® is currently being utilized for production mining by a major company in Sudbury, Ontario. Both truck and conveyor anciliary haulage are being utilized. The paper describes the development of the loader and how it may be applied in tunnelling applications.

Jan 1, 1987

By Richard H. Sailors

Data from full scale marked ball tests are used to demonstrate the effects of abrasion, corrosion, and impact on overall wear rate. The predominate wear mechanism need be identified before the optimum alloy can be chosen for the grinding media. Use of high chromium grinding media often results in increased mill efficiency due to shape retention. Thus, a benefit from energy savings can result as well as a reduction in wear rate. Converting from steel to east high chromium grinding media requires close association and cooperation between producer and consumer in order to properly conduct these studies.

Jan 1, 1990

By W. K. O’Connor, J. C. White, P. C. Turner

The US Bureau of Mines is investigating the cobalt and manganese resource of the West-Central Arkansas district through field investigations, mineralogical characterization, beneficiation and hydrometallurgical tests. Located within the Ouachita Mountains, these structurally-controlled deposits occur along the axes of anticlines that form the mountain ridges. Brecciated novaculite is cemented with a mixture of manganese oxides, primarily cryptomelane and psilomelane. Cobalt is concentrated within lithiophorite, a particular Mnoxide phase. Chemical analyses of head samples reported up to 25% Mn and 0.17% Co. Magnetic separation yielded products containing up to 41 % Mn and 0.22% Co at recoveries of 95% and 93%, respectively.

Jan 1, 1993

By D. Lelinski, R. Bokotko, J. D. Miller, J. Hupka

Air-sparged hydrocyclone (ASH) flotation is a new, promising technology, and, since its conception, numerous applications have been successfully tested. Nevertheless, research and development efforts have continued to improve the technology with respect to operating conditions and design considerations. Results, from experimental studies on bubble generation in the ASH system are presented in this paper. Bubble size distributions generated during ASH operation were determined using a high-speed photographic technique. The influence of many factors, including surfactant concentration, water flow rate, and porous-tube pore size have been studied. Test results indicate that these process variables have a profound effect on the bubble size distribution. With an increase in surfactant concentration or water flow rate (shear field), the bubble size distributions become narrower and shift toward smaller average bubble diameters. However, the influence of pore size is more complicated. Depending on the experimental conditions, the average bubble size was found to range from about 100 to 300 µm in diameter.

Jan 1, 1997

By Mulong Yu, Yosry A. Attia

Beneficiation of high magnesium Florida phosphates requires ultrafine grinding to liberate the dolomite (the main source of magnesium), and a separation process capable of dealing with ultrafine sizes such as selective flocculation. The objective of this study was to investigate the feasibility of separating dolomite from apatite ultrafines by selective flocculation. To achieve this objective, selective polymeric reagents to either dolomite or apatite must be first designed and synthesized. This challenging task was accomplished by carefully selecting complexing/chelating agents which are selective to either the Ca or Mg ionic sites on the minerals, and incorporating these reagents into the structure of long chain water soluble polymers to obtain either selective flocculants (with high molecular weight, MW, polymers), or selective dispersants (with low MW polymers) to either the dolomite or the apatite particles. Synthesis and testing of these polymers on individual and mixed mineral slurries, and on a sample of natural high magnesium phosphate ore, have been attempted and the results are described in the paper. The preliminary results showed encouraging signs for the feasibility of selective flocculation separation of dolomite from apatite.

Jan 1, 1993

By M. Alnot, J. A. Mielczarski, J. J. Ehrhardt, J. M. Cases

The flotation behavior of minerals depends on the balance between hydrophobic and hydrophilic species present at the surface of the minerals. The direct characterization of the interfacial products formed by the interaction of water and an aqueous solution of amyl xanthate with chalcopyrite, tetrahedrite and tennantite (the two former contain antimony and arsenic) were carried out by X-ray Photoelectron Spectroscopy (XPS) and infrared (IR) reflection spectroscopy. The experimental data collected from in-situ (IR ATR) and ex-situ (XPS, IR External Reflection) measurements have let us determine the types of the adsorption products and to propose mechanisms of interaction between the aqueous solution of surfactant and surface of the investigated minerals. It is shown that two major processes take place at the mineral interfaces: (i) the interaction with water and oxygen resulting in the formation of the oxidation products which are mainly hydrophilic (but also a hydrophobic product was found), and (ii) the adsorption of xanthate producing different types of hydrophobic surface products. The results obtained show differences in the composition of the outermost atomic layers of the investigated minerals which obviously will produce differences in the flotation behavior of these minerals. This work forms a good fundamental basis for a better separation between copper minerals containing arsenic and antimony, and chalcopyrite.

Jan 1, 1995

By D. M. Galbraith

British Columbia's physiography - the mountains, valleys and watercourses - provides the basis for rich and varied plant and animal resources and for complex land uses. Mining alters the physical environment in a manner that may create a disproportionate impact on biological resources and land use systems. The object of environmental legislation is therefore largely the protection of the basic physical environment: land surface, water, and air. The pace of mineral exploration, placer mining, and underground and surface gold mining has recently quickened in British Columbia, testing the ability of both industry and regulatory agencies to respond to legislative requirements. Some parameters of mining activity have critical significance for environmental protection, for example: the area disturbed; the physical and chemical qualities of ore, waste and overburden; and the nature of materials handling. Acid mine drainage is a particular hazard. Provincial legislation that applies to mining includes the Mines Act, the Environment Management Act, the Waste Management Act, and the Water Act. Government of Canada legislation includes the Fisheries Act and the Metal Mining Liquid Effluent Regulations. Every new mine proposal in British Columbia is reviewed in the Mine Development Review Process, which receives its mandate from the Provincial Environment and Land Use Cabinet Committee. The proponent submits reports to the Mine Development Steering Committee in succeeding stages: Prospectus, Stage I (after which approval-in-principle may be granted by ELUC); and if necessary Stage 11. Stage 111 is the

Jan 1, 1987

By F. M. Doyle, P. E. Richardson, E. Peters

A number of studies have attempted to correlate the semiconducting properties of mineral sulfides with their chemical reactivity. Frequently such studies are conducted on polished or abraded electrodes. Defects produced by abrasion may mask the influence of the semiconducting properties of electrodes, e.g., by pinning the Fermi level at the surface or by reducing the lifetimes of photogenerated charge carriers. It is shown that pyrite and galena electrodes have photocurrents that are extremely sensitive to abrasion of the electrodes. On freshly fractured galena surfaces, the space charge layer is readily polarized. Wet-abrasion is shown to produce a relatively thick ptype layer on galena electrodes and this p-type layer has a pronounced effect on the photoresponse. On freshly fractured pyrite surfaces, the Fermi level at the surface is pinned by a surface state. Wet-polishing reduces the magnitude of the photocurrent by over an order of magnitude.

Jan 1, 1993

By V. T. McLemore

The Steeple Rock district in New Mexico is a major epithermal gold-silver district that exhibits district zoning. Five types of ore deposits occur within the district: •base-metal veins (with gold and silver) form the center of the district and occur along the Carlisle fault, •gold-silver veins along northwest-trending faults and outward from the base-metal veins, •copper-silver veins along the margins of the district, •fluorite veins along the margins of the district, and •manganese veins along the margins of the district. Areas of older acid-sulfate alteration occur throughout the district and also exhibit the following zoning: massive silica/chert zone (inner), silicified zone and clay zone (outer). This alteration overlies regional alkali-chloride (propylitic to argillic to sericitic) alteration. Synthesis of available data suggests the acid-sulfate alteration is related to a shallow, but older, epithermal hot-springs system. Subsequently, younger epithermal veins formed along faults.

Jan 1, 1996

By D. Harris, M. Osterberg

This paper examines the economics of acquiring mineral exploration rights by royalty-rate bidding when the royalty basis does not provide for full cost recovery. Bidding takes place prior to exploration and the documentation of actual tonnage and grade. Consequently, it increases considerably the risk to exploration capital when the fraction of cost recovered is small and the product price exhibits large fluctuations. Price and grade risk are demonstrated on a 360-Mt (400-million-st) porphyry copper deposit by Monte Carlo simulation of discounted-cash-flow analysis. Copper price is modeled as a stochastic price process, and costs are based on US Bureau of Mines cost models. When both grade and price risk are considered, the probability for a negative NPV is 0.54, given a royalty rate of 5% applied to a basis that allows the recovery of costs up to 50% of product price. Investment risk could be considerably reduced by defining the royalty basis to allow greater cost recovery. Although such a basis would require society to share in the risk, society would benefit from greater resource development.

Jan 1, 2000

By K. R. Weller, U. J. Sterns, P. S. B. Stewart

Complex sulphide ores usually require very fine grinding of the whole ore stream to achieve adequate liberation. Recent improvements to DSM screens have made this device appear competitive with cyclones in circuits treating these ores. A DSM screen and cyclones were tested in pilot-scale grinding of a copper, lead, zinc ore and the resultant data were used to establish a multi-component simulation model. The model was used to assess the influences of mill environment, circuit flows and pulp densities, final product properties (size, relative size and SG of the values, and liberation characteristics) and a second grinding circuit on capacity and product size distributions, and hence define conditions for which one device is better than the other.

Jan 1, 1992

By Alan E. Isaacson

Extensive gravel deposits exist within a six-county area in the mountains surrounding the Salt Lake Valley, and in the mountain ranges to the west. The six-county area includes Davis, Salt Lake, Summit, Tooele, Utah, and Wasatch Counties. The majority of these are beach deposits from prehistoric Lake Bonneville. However, real estate development associated with a projected population increase of 54 percent over the next 20 years is expected to remove most gravel deposits in Salt Lake County from consideration for mining, forcing gravel operations to relocate from eastern Salt Lake Valley to the Oquirrh and Stansbury Mountains farther west. The gravels in these ranges are of lower quality and require additional processing to manufacture asphalt and concrete. Replacing gravel resources along the Wasatch Front with resources in the Oquirrh and Stansbury Mountains over the next 20 years has the potential to increase construction costs by nearly $1 billion. The majority of this cost (82 percent) is the result of increased transportation costs due to longer distances to market. The remainder of the cost is attributable to lower quality gravels that will require additional processing in the manufacture of asphalt and concrete. The following analysis and discussion does not take into consideration the amount of crushed stone that is currently being used in the construction industry in northern Utah, its use as a substitute for lower quality gravels, or as a factor in the base case projection.

Jan 1, 2001

By Gustavo G. Pilger, Jair C. Koppe, João Felipe C. L. Costa

Information for mine planning requires to be close spaced, if compared to the grid used for exploration and resource assessment. The additional samples collected during quasi-mining are frequently located in the same pattern of the original diamond drill holes net but closer spaced. This procedure is not the best in mathematical sense for selecting a location. The impact of an additional information to reduce the uncertainty about the parameter been modelled is not the same everywhere within the deposit. Some locations are more sensitive in reducing the local and global uncertainty than others. This study introduces a methodology to select additional sample locations based on stochastic simulation. The procedure takes into account data variability and their spatial location. Multiple equally probable models representing a geological attribute are generated via geostatistical simulation. These models share basically the same histogram and the same variogram obtained from the original dataset. At each block belonging to the model a value is obtained from the n simulations and their combination allows one to access local variability. Variability is measured using an uncertainty index proposed. This index was used to map zones of high variability. A value extracted from a given simulation is added to the original dataset from a zone identified as erratic in the previous maps. The process of adding samples and simulation is repeated and the benefit of the additional sample is evaluated. The contribution of an extra sample was evaluated locally, globally and in terms of variation in total measured resources. The procedure showed to be robust and theoretically sound, mapping zones where the additional information is most beneficial. A case study using coal seam thickness illustrates the method.

Jan 1, 2002

By J. P. Earnhardt

Recycling of such municipal solid wastes as glass containers, metal cans, and newspapers has received increasing attention recently. However, municipal solid wastes account for only 1% of the total solid waste stream in the United States. The remainder includes hazardous and non-hazardous industrial wastes. Generators of industrial wastes are facing higher landfill costs. Future liability potential, and public image concerns which are forcing them to seek innovative and often profitable solutions to minimize, reuse, and recycle their waste streams. Opportunities for the mining industry in industrial recycling include recovery of mining wastes and by-products, and utilization of mineral products for treating waste streams.

Jan 1, 1993

By Michael Schultz, Gregory Sanders

The City of New Haven is proposing to construct Downtown Storm Sewer Infrastructure Improvement project to mitigate on-going stormwater flooding in the Long Wharf District. The proposed project includes a 200 cubic feet per second (cfs) stormwater pump station; and a 914 meter (3,000 linear feet) long tunnel segment with an internal diameter of 2.1 meters (84-inches). The tunnel alignment will cross under the Long Warf railyard and then continue parallel to the Vison Trail Route. This paper presents the local geology and subsurface conditions, as well as discusses the major project challenges and risks including construction in soft marine soils and encountering remnants of the former wharf.

Jun 13, 2021

By J. Linhart

In vertical airways, falling material - solids-or water - may cause undesirable disturbances in the ventilation in the airway itself and also in neig¬bouring airways unless precautions are taken to stabilize the air flow. Such cases can occur, for example, - in shaft sinking by drilling from a pilot hole, - during the filling up of shafts, and - during the introduction of water into shafts in the case of mine fires. In an airway with upward ventilation the falling material will reduce the air flow and may even re¬verse its direction. In an airway with downward ventilation the air flow can only increase, but a reversal of the direction of ventilation may result in a parallel airway. These disturbances in the normal ventilation are undesirable as it must be the aim to have ventilation that is stable in quantity and direction throughout a mine. In order to be able to prepare suitable stabilization measures one must know the pressure generated by the falling material; this pressure will henceforth be called "aeromotive" pressure. The main factors determining the influence of falling material on the ventilation are - the amount of falling material and its height of fall, - the cross sectional area of the airway, - the pressure. difference prevailing in it, - the-position of the. airway in the ventilation. network, - the air velocity, and - other parameters, e. g. the density and grain size of the falling material. To determine the aeromotive pressure-measurements have been made underground during the sinking and filling of shafts and systematic studies have been carried out during the supply of water into a staple shaft. The present paper deals first with some fundamental theoretical considerations and then describes the measuring arrangements and the results of the series of experiments that have been carried out.

Jan 1, 1980

By Stéphane Servant, Jacques Ouellet, Ferri Hassani

This paper presents essentially the logistic and practical aspects involved for in situ testing of mine paste backfill with a self-boring pressuremeter. The investigation discussed in this paper is part of an extensive and ongoing research project to identify and validate an in situ testing technique for cemented mine backfill such as hydraulic or paste backfill as well as Insitu behavior of backfilled stopes. After a literature review on field testing of soils and past experiments on mine backfill in situ testing, the self-boring pressuremeter was selected as the most appropriate instrument for this task. The authors presents in this paper the technical aspect involved in a field trials that was conducted in a Canadian underground mine using paste backfill. The results of this first successful trials show that self-boring pressuremeter test can provide high quality and reliable backfill characteristics results, using analytical techniques developed for soils (Ouellet et al., 1998). The parameters obtained were: estimation of the lateral stress in the ground, the soil stress-strain response and the soil strength. The logistic and equipment required to conduct such testing underground is fully described. Performance achieved in the field and technical difficulties encountered are highlighted. Recommendations for future experiments with such instruments are given. Some potential technical improvements to better adapt this in situ testing technique to mine backfill are proposed.

Jan 1, 2001