Search Documents

By Michael DiMatteo, Michael D. Gardner, Eric F. Perry, John K. Felbinger, Robert S. Evans

A hydrologically isolated surface coal mine was reclaimed using acid material handling, alkaline addition and ground-water management techniques. Eight pit floor drains were installed during reclamation to intercept ground-water flow in the mine backfill and minimize water table buildup. All drains began flowing within six months of installation. Water quality and ground-water discharge have been monitored for four years after mine closure. A thin water table aquifer about five to seven feet thick has developed in minespoil about 20 to 40 feet thick. Ground-water flow direction is largely controlled by geologic structure and the drains. Median ground- water discharge is about 0.43 gallons per acre per minute, and varies an order of magnitude between wet and dry seasons. About 19 % of precipitation enters the aquifer as recharge. Seven of the eight drains typically discharge net alkaline water. Alkalinity is produced continuously and concentrations are highest during dry periods. Conversely, sulfate and acidity concentrations increase during wet periods as slugs of accumulated acid products are leached. Overall water quality is controlled principally by minespoil geochemistry and added alkaline material. The drains have successfully directed ground-water to a planned discharge area. Without the drains, a ground-water mound was expected to form against a buried highwall and discharge over a large area.

Jan 1, 2000

By N. Finkelstein, C. G. Palagi, S. S. Stillar

The C. E. Weed concentrator treats 51,000 tons per day of 0.5% to 0.7% copper ore received from the Berkeley Pit, the Continental East Pit and the Butte underground mines. Improved operating techniques and conversion from semi-autogenous secondary grinding to ball milling have increased tonnage from an original design of 42,000 tpd. Separate treatment of sands and slimes, with recovery of soluble cop- per from the slimes, has increased total copper recovery. Concentrator tailings are pumped 600 vertical feet and 20,000 horizontal feet for disposal.

Jan 1, 1976

By Herbert H. Einstein, Edward C. Tse, David B. Ashley

INTRODUCTION Decision-making in the design and construction of underground facilities must be made under conditions of varying geologic uncertainty, uncertainty which can have a major cost impact if not properly regarded. Of the two approaches for dealing with this variability, preparing for the "worst" anticipated conditions and optimizing design and construction in-situ, preparing for the "worst" conditions is the more if not solely conventionally practiced method in the United States. While the conventional approach is recognized at times to be extremely overconservative, it will remain preferred until a more adaptable method is shown to be economically superior. This paper presents research aimed at providing just such answers as to when and if an adaptable tunnel design and construction approach is more cost effective than a non-adaptable one. To fully understand the characteristics of this choice between adaptable and conventional tunneling alternatives a summary discussion of adaptable methods is presented. An acknowledgement of the importance of geologic and other factor uncertainties in making this decision leads to the adoption of decision analysis as a quantitative methodology for formalizing the problem. Exercising this methodology on three prototypical tunneling scenarios--urban deep, urban shallow, and transmountain--allows an isolation and ranking of the most crucial factors in making the basic approach decision. One scenario, a transmountain highway tunnel, is carried further through a detailed probabilistic analysis to show under what conditions of varying uncertainty adaptable approaches possess economic advantages.

Jan 1, 1979

By L. R. Moore

The World Health Organization (WHO) considers contamination from oxyanions, such as selenium and arsenic, a global concern. While their elemental forms are toxic, the aqueous oxyanions are more so. These aqueous forms, which exist at a higher oxidation state, are the most common forms released during mining processes. Many technologies are capable of meeting the governmental discharge criteria for oxyanionic contaminants, but may possess limitations due to redox chemistry as well as the water matrices. An innovative technology was developed that can successfully reduce such aqueous forms generated during mining processes to a level below the discharge criteria. This paper discusses how an understanding of the sensitivities of this novel adsorbent towards these variations in water matrices and redox chemistry can be used to optimize its application.

Feb 27, 2013

By Stephen Stone, Kerby Dobbs, G. Richard Whittecar, W. Lee Daniels, Zach Agioutantis, Tess Thompson

A common result of Environmental Impact Assessments associated with mining projects is the construction of new wetlands in areas disturbed by mining operations. Where appropriate, this mitigation may be considered an integral part of the mine reclamation process under the principles of sustainable development in the minerals industry. Wetbud is a new tool for estimating wetland water budgets using available weather data and site-specific topographic, soil and geohydrologic data, coupled with mass balance mathematics. Wetbud is primarily intended as a planning tool for use in the design of created wetlands, but it can also be applied to native wetlands or wetland restoration sites where the required input parameters can be specified. Wetbud can be run in its basic form where wetland topography, soil parameters and groundwater flux are simplified, or in the advanced form, where these parameters are included in a more complex approach via integration of the MODFLOW package, a free 3D program that was developed by the United States Geological Survey. Both versions can also include overbank flow hydrology sources and the advanced form can also model sloping and irregular topography. The program downloads weather data from the nearest applicable station and selects appropriate wet-normal-dry (W-N-D) years following a modest user data clean-up step. Wetbud also has the ability to utilize existing short-term (e.g. 6 to 9 months) groundwater data from an up-gradient well to simulate longer-term groundwater level inputs for the selected W-N-D years. In addition, Wetbud features a “Wizard” version that comes pre-loaded with 14 pre-selected weather data sets for all areas of Virginia that can develop a simple monthly water budget in less than 15 minutes – a feature that could be expanded anywhere geographically with historic weather data.

Jan 1, 2017

By Donald L. King, Frank A. Baczek

Sedimentation-based equipment is used in applications where separation of solids from liquid by gravity settling is desired. If a concentrated solids slurry is desired, the equipment is designed to "thicken"; if a clear liquid is desired the equipment is designed to "clarify." Thickeners normally handle higher solids loading rates than clarifiers, which usually process feed slurries containing low concentrations of suspended solids. Thickeners are therefore designed for heavier-duty requirements, and clarifiers have extra features to ensure more complete suspended solids removal. Major components (Figure 1) that are common to all sedimentation-based equipment are: tank, drive-support structure, drive unit and lifting device, rake structure, feed well, and a means of overflow and underflow withdrawal. Specific features are designed interdependently after the overall separation approach is defined conceptually. This conceptual approach is usually based on past experience or evolves from sedimentation studies conducted on samples of the slurry to be handled. Because many variations and combinations of components are possible, the overall conceptual approach has a number of possible designs that will accomplish the desired results. The final choice is based on practicality, potential for minimizing upsets, and cost.

Jan 1, 1986

By David A. Holmes

After a century of variable government-supplied housing on their cold, windswept lands, and facing extremely limited natural resources and no timber, the Standing Rock Sioux Tribe has launched a study into alternative housing approaches for their people. Considering that they have little more than the soil and limited river aggregates under their feet, the Tribe has elected to consider adobe and earthen-wall construction. Earthen construction is no stranger to the Sioux lands. Smaller tribes, including the Mandan, Arikira, and Hidatsa, lived here among the Sioux in earthlodges for centuries. Such earthlodge structures were not unlike the Southwestern jacal style-a framework of upright branches and branches covered with mud-employed by the Anasazi about A.D. 700-900. Indeed, the Sioux people themselves evolved from earlier earthlodge dwellers. Indigenous peoples in New Mexico, Arizona, and neighboring Mexico have used earthen-wall housing for many centuries, reinforcing Sioux observations that this is today an earth-friendly, cost-effective, and practical approach. The Cheyenne River and Pine Ridge Sioux Reservations also recently have conducted studies on earthen- wall construction. This paper describes the search for and evaluation of potential raw-material resources for earthen-wall/adobe construction on the Standing Rock Reservation in North and South Dakota. Significant resources of clay/silt materials (8 million tons in the Striped Cloud clay bed) suitable as adobe binders and sand-and-gravel aggregate (2.5 million tons) that could support earthen/adobe construction have been identified throughout the Fort Yates Flat area on the Reservation. Also addressed is how adobe and rammed-earth construction could add to the diversity of reservation construction and address future Tribal housing and other building needs.

Jan 1, 1999

By I. E. Odom

An electron optical and microprobe study was made to determine the physical and chemical nature of the silica minerals that occur as natural impurities in bentonite and montmorillonitic fuller&apos;s earth clay products (both granular and powder) and that occur in <10-µm dusts from plants that process these products. The purpose of the study was to determine if discrete "free" silica minerals, such as quartz, could be observed using SEM and EDS methods. No “free" silica minerals could be observed in the SEM images of the granular and powdered products, either among or on the surfaces of the particles. Also, no “free" silica could be identified by either SEM or EDS analyses of the dusts, even though quantitative X-ray diffraction analysis indicated that trace amounts of quartz occurred in all samples. It was determined that these quartz and other silica minerals were encapsulated or coated by montmorillonite. Vigorous washing, however, removed some of the clay coatings, so that small amounts of silica minerals could be seen by SEM and EDS analysis. It was found that all primary crystalline quartz grains in the bentonites have diagenetic overgrowths consisting of a mixture of montmorillonite, opaline silica and possibly microcrystalline quartz. Detrital quartz grains in the fuller&apos;s earth have thin diagenetic overgrowths of opaline silica, also containing montmorillonite. The clay encapsulation of the silica minerals in the products studied, as well as in the potentially respirable (<10-µm) dust produced during manufacturing of bentonite and montmorillonitic fuller&apos;s earth clay products, is considered to be an important factor influencing the potential health effects (e.g.. silicosis) of the contained silica. Even if clay dust containing silica should be inhaled, the montmorillonite encapsulating the quartz and other silica minerals would prevent direct contact of the silica with lung tissue. The clay encapsulation of quartz, as well as the highly hydroscopic nature of montmorillonite, may explain why not a single confirmed case of silicosis has ever been reported among plant workers in more than 65 years of production.

Jan 1, 1998

By Jan Visman, James W. Parkinson

GENERAL INTRODUCTION Sample collection, preparation and analysis are all steps in a single process designed to provide information about a much larger amount of material than the sample itself. For example, information about the ash content of a unit train load of coal may be derived from a single, relatively small sample of perhaps a few hundred pounds (liters) extracted from the entire shipment. These three steps can be thought of as links in a chain, allowing the simple analogy that the strength of the chain, or, in other words, the value of the information is only as strong as the weakest link. Sample collection, discussed in Part 1 of this chapter, is critical because analytical procedures can do no more than reveal the characteristics of the sample presented to the laboratory. If that sample does not properly represent the population to be characterized, neither will the analysis of that sample. Sample preparation is also a critical part of the chain. Any change in the nature of a sample between the time it is collected and the time it is analyzed will appear to reflect the nature of the population. For example, sample preparation procedures that allow air to partially dry the coal sample before reaching the laboratory will cause the sample analysis to indicate a lower moisture content than the sample originally had. Other changes can be more subtle. Second only to moisture loss, oxidation reactions generally cause the greatest problems. Oxidation of a coal sample can alter surface properties, changing flotation response. In extreme cases, combustion parameters, such as caking or agglomerating properties or mineral composition, such as pyrite content, can change. Water samples can also be altered by oxidation. For example, ferrous iron can oxidize to ferric iron, possibly changing water quality parameters such as pH. Sample analysis, the subject of Part 2 of this chapter, is the final link in the chain. Obviously, no laboratory procedure can correct for problems created by improper sample collection and preparation. At the same time, poor analytical techniques will create incorrect information about the total amount of coal from which the sample was extracted (the population) in the same manner as improper sample collection and preparation. The key to gaining correct information about the population is to view these three steps as parts of a single process. Following proper techniques through only one or two steps of the process will not produce accurate information.

Jan 1, 1991

By Chunlin He, Xinsheng Li, Feng Yang, Lu Han, Yuezhou Wei, Feng Gao

The solvent extraction of vanadium (V) from Na2CO3–NaHCO3 solution was attempted using Aliquat-336 (methyltrioctylammonium chloride) extractant dissolved in sulfonated kerosene as diluent with 2-octanol as phase modifier. The influence factors, such as Na2CO3 concentration, NaHCO3 concentration, temperature, extractant concentration and impurity P, on vanadiumextraction were investigated. The results revealed that the single stage extraction efficiency of vanadium reached above 89%from 20 g/L Na2CO3 – 20 g/L NaHCO3 solution under the following conditions: extractant concentration of 15%, room temperature of 20–30 °C, 2-octanol of 6%, phase ratio (O/A) of 1:1, and oscillation time of 1 min. The addition of NaHCO3 into Na2CO3 solution could lower the pH value of the Na2CO3 solution, improve extraction efficiency of vanadium, and not introduce other impurities. The phosphate anion did not interact with the vanadate anion in the Na2CO3–NaHCO3 solution. The P in the Na2CO3–NaHCO3 solution had little influence on vanadium extraction.

Jul 30, 2020

By James A. Deane

Strip mine reclamation Fs the process of restoring the land affected by the mining process to its most productive use. This can be timber production, pasture, crop land, wildlife and/or recreational use. The mining companies must determine, through the advice of their technicians, what the most advantageous use of the land will be. If the Company does not own the surface, the owner or owners must be contacted to determine their desires as to how the land should be reclaimed. Many times, in making the plans to restore an area with vegetative cover, the watershed and the quality of the water in the area is overlooked. The water itself must be an integral part of the reclamation plan. Many lakes and/or pits can be created with proper planning. In areas in the Midwest, where lakes are a scarcity, these strip mine lakes can become storage reservoirs for large amounts of water, They can help control runoff and low flow augmentation. The strip mining operation will affect the watershed regardless of whether a reclamation plan in made or not. It is up to the reclamation technician to see that the plan benefits the watershed instead of affecting it adversely. This can be done during the operation by intercepting the water before Pt enters the active pit. Diversion ditches above the highwall will handle the runoff water from the watershed. Water that does gain entry into the pit should be removed as quickly as possible. If the rules and regulations adopted by the Ohio River Valley Sanitation Commission in Resolution 5-60 are followed, water encountered during the operation can be handled with little or no adverse effect to the receiving watershed.

Jan 1, 1965

By M. J. Senk, A. Lusin

Federal regulations require that methane liberated at the face be diluted and removed to maintain methane gas concentrations below 1pct (CFR) in working places and intake air courses. The delivery and distribution of intake air at the face is critical for effective face ventilation. Improved techniques for monitoring the movement of intake air to the face are needed. A test system was developed and a computer program written for using a three-axis ultrasonic anemometer to measure airflow in a simulated mine entry. Results of tests conducted in the entry showed that the anemometer is a valuable tool for measuring mine airflow conditions near the face.

Jan 1, 2003

By Y. C. Kim

For the past quarter of century, much more effort and research have been expended in developing the "optimum" ultimate pit limit design algorithms and much less to solving the "optimum" open pit production sequencing. However, the potential economic benefit to an operating mine is far greater for the latter than the former. Unfortunately, the problem of "optimum" open-pit production sequencing has not been fully solved to date. This paper first reviews the past and currently used methodologies for developing this sequence. The staggered pit phase geometry problem of advanced stripping and operational constraints such as ore and waste tonnage requirements by period and necessary contiguity of mining faces are the main reasons why the "optimum" production sequencing problem has not been solved as yet. This paper also explains why any method which attempts to simplify the problem using ultimate pit limit design algorithm will fail to reach an "optimum" solution.

Jan 1, 1994

By Carl-Henrik Knudsen, Rolf Tore Arnesen, Eigil R. Iversen

Recovery of iron and copper from acid mine drainage was studied in pilot scale at a continuous treatment plant at the mine site of the King&apos;s mine in Roeros, Norway. The average load on the plant was 1 m3/h. The process tested in this project is a three-step process consisting of: 1) Fe(OH)3 precipitation at pH 3.5, dewatering of iron sludge and transport to ferric chloride plant; 2) after filtration precipitation of residual metals at pH 9, concentration of metal sludge by flotation; 3) extraction of metals from the sludge with sulphuric acid followed by recovery of copper by electrolysis. The copper could be used for local production of different crafts, but this condition needs a further evaluation. The process economy at a full scale plant is evaluated.

Jan 1, 2000

By E. H. Christiansen

Gem-quality red beryl in the Wah Wah Mountains of southwestern Utah formed as a post-magmatic mineral in a topaz rhyolite flow. Unlike topaz, this beryl occurs along fractures in devitrified rhyolite, rather than in lithophysal vugs. The flow occupies a graben and perhaps a significant paleo-drainage. Beryl occurs at medial depths within the eroded flow, about 170 m below overlying mafic lava flows. Both beryl-bearing fractures and the host rhyolite show an unusual amount of argillic alteration compared with other topaz rhyolite flows. Alteration may be related to the incursion of surface water along shrinkage fractures within the flow. Whole-rock concentrations of CaO within the host rhyolite are very low (<0.01 % to 0.18%) compared with other topaz rhyolites and Be concentrations (about 20 ppm) are about average. Low Ca activities prevented fluorite precipitation and allowed Be transport as fluoride complexes. Beryl probably grew at subsolidus temperatures (-300-650°C), but above the temperature of kaolin development (200-300°C) as fluoride-rich vapors, released by devitrification, encountered fractures and mixed with vapors derived from surface water flowing through the fractures. Beryllium fluoride complexes reacted with water vapor, silica minerals, alkali feldspar, water, and Fe-Mn oxides along fractures to produce red beryl. Continued reaction of the cooling flow with surface water at lower temperatures probably produced a boiling, more acidic fluid that produced the argillic alteration. Consequently, eruption of low-Ca topaz rhyolite followed by entrance of surface water into medial portions of a devitrifying and still hot lava flow appear to be critical factors that led to red beryl formation.

Jan 1, 1996

By Derek M. Hutchinson, Don Zeni

The construction of shafts by blind drilling has been made cost effective by advances in technology and experience. The techniques of blind shaft drilling are discussed and a brief history presented. A recent use of blind shaft drilling to access a small gold ore body in Australia is described. Finally, the most recent developments in drilling machinery are reviewed together with possible applications in new and existing mines.

Jan 1, 1987

By I. Iwasaki, K. A. Smith, X. Cheng

The reaction mechanism for the cathodic decomposition of pyrrhotite in deoxygenated solutions at natural, near neutral pH levels was studied using potential and cyclic voltammetric measurements. Reaction products on the pyrrhotite surfaces were examined by Auger Electron Spectroscopy (AES), by X-ray photoelectron spectroscopy (XPS) and by analyzing the voltammograms for the electron balance of the reactions. Surface properties of the pyrrhotite/solution interface were characterized using an ac impedance technique. The parameters of an equivalent circuit were determined by the nonlinear least-squares fit (NLLSF) technique. The effect of cathodic polarization on floatability was investigated by performing microflotation tests. Possible implications to the flotation separation of chalcopyrite-pyrrhotite ores are discussed.

Jan 1, 1995

By Thomas R. Yanske, Jonathan E. Carmack, Lyndon M. Clark

In order to maximize the extraction of high grade pillars at The Doe Run Company, artificial pillars are created using cemented rock fill (CRF). CRF pillars aid extraction of pillars in two ways. One is to offer back support for the immediate area where pillars are being extracted. The second is to increase the post failure residual strength of pillars surrounded by backfill. The CRF is produced using a combination of minus 1.0 m run of mine (ROM) rock and minus 5 cm crushed rock. Depending on the operation the CRF slurry is either produced in an underground or a surface batch plant. The slurry and rock are transported to the fill area by truck where they are mixed and placed in 1 m lifts. To reduce the amount of CRF needed, fill fences are constructed around the perimeter of the CRF pillar. Within these fences ROM CRF is placed in lifts until within 0.6 m of the back after which minus five centimeter CRF is slung tight to the back utilizing slinger trucks. In constructing these artificial pillars a number of set procedures have been established to ensure that the work is done both properly and safely.

Jan 1, 2001

By Sergey G. Pushkin, Eugeny L. Schastlivtsev, Anatoly A. Bykov

Three years ago the authors and a group of assistants began to develop a GIs-system for integration of comprehensive eco- logical information to be linked to geographical maps of Kuzbass region. And now we have got the working system and some first results that the present paper deals with.

Jan 1, 1996

By Jean-Luc Cornet

Advances in conveyor technology over the past decade have enabled the design and erection of very long overland belt conveyors. Such conveyors usually require head and tail drives to lower the belt tension and belt strength required. This paper provides an overview of the problems encountered in controlling the head and tail drives on such conveyors and some of the solutions developed by CDI for several such projects.

Jan 1, 2002