Search Documents

By Patrick Hannon

In this presentation, it is intended to briefly describe some occurrences of lead-zinc mineralization in Mississippian carbonates of central Nova Scotia. Results of geophysical and geochemical prospecting are presented. Because the deposits do not give positive identification to these indirect techniques, it is necessary to site exploratory drilling through the development of geological concepts.

Jan 1, 1975

By Robert L. Wade

The two primary goals in underground coal mining are to improve safety and to lower mining costs per ton through increased productivity. However, as evidenced by the drastic decrease in. productivity since the enactment of the 1969 Coal Mine Health and Safety Act, (the Safety Act), these goals appear to be mutually exclusive. Millions of dollars have been spent in the res, arch and development of systems to solve this problem. Before the Safety Act, "productivity had experienced a 25-year history of continued increases ...? (Douglas, 1980). But since its enactment there have been dramatic decreases in productivity accompanied by phenomenal increases in mine costs. Labor trends, depletion of the more readily minable underground coal reserves and other factors have contributed to this situation, but the dominant factor is undoubtedly the Safety Act itself. To illustrate, prior to 1969 underground coal mine production was much greater than surface mine production but since then underground mine production has been declining at a rate greater than the overall growth rate of total coal production.

Jan 1, 1985

By Fredrick C. Kruger

We can confidently predict such obvious long-term trends affecting the minerals industry as - increasing consumption, exhaustion of easily discovered near-surface ores, and sharp limitations upon open pit mining by environmental considerations. There- fore, we must intensify the exploration for, and the development and exploitation of, deep bodies of potash and other ores. This paper examines the state of the art of the search for, and the evaluation of, potash from both a geological bias and a mining practicability. The use of indirect geological methods and geophysical techniques, followed by expensive deep drilling, are the conventional approach to evaluation and development of mining plans. The geologist and the geophysicist will have to find ways to perform both of these tasks better and cheaper.

Jan 1, 1973

By Kevin Andrews, SETAREH GHAYCHI AFROUZ

Ground control analysis and groundwater inflow assessments for underground coal mines require in-depth field investigations including, but not limited to, geological and geotechnical core logging, downhole geophysical logging, laboratory rock strength testing, and packer (Lugeon) testing. Field and laboratory data collection are time consuming and expensive, and an initial understanding of the expected trends among various geotechnical and hydrogeological parameters can assist with the planning and optimization of geotechnical characterization studies and grouting plans. In this study, a comprehensive database is analyzed, comprised of important rock mass characteristics (hydraulic conductivity, rock quality designation (RQD), and lithology) for coal-bearing rocks in the Central Appalachian Basin. Statistical analysis of the data is completed to establish an enhanced understanding of geotechnical and hydrogeological conditions expected to be encountered as underground coal mining passes near and beneath streams and rivers. The results of the study provide valuable reference material for the coal mining industry for completion of shaft installations, mine stream crossings, environmental assessments, and grouting and mine dewatering designs.

Jul 1, 2023

By Daniel W. H. Su

The ability to predict the effects of longwall mining on topography and surface structures is important for any coal company in making permit applications and anticipating potential mining problems. The sophisticated finite element model described and evaluated in this paper is based upon five years of underground and surface observations and evolutionary development of modeling techniques and attributes. The model provides a very powerful tool to address subsidence and other ground control questions. The model can be used to calculate post-mining stress and strain conditions at any horizon between the mine and the ground surface. This holds the promise of assisting in the prediction of mining-related hydrological effects.

Jan 1, 1986

By Gabino Preciado, Louis Sandbak

Corrosion has long been identified as a potential risk to the long-term ground support stability due to degradation of internal ground support elements such as rock bolts but also to surface support from mesh, straps, bolt plates, and ancillary support of utilities such as hangers. The emphasis is to understand the corrosion mechanisms on the primary ground support elements and any supplemental steel or arch sets. The water and chemical processes from oxidation(rust), stress corrosion cracking, and even the electrical charge created during these reactions contribute to the corrosion of the steel support elements. The main goals are to mitigate the effects of corrosion and to be able to predict those areas of high water or high sulphide for potential rehab maps. It is also essential to identify and classify the visible corrosion as part of damage mapping and provide bolt testing to those areas of suspected internal damage from corrosion. This is important to get an estimate of the support longevity or expected life before rehab to minimize the overall cost of the operation.

Feb 1, 2024

By E. M. Schern

The Morenci/Metcalf porphyry copper mining operation, located in southeastern Arizona, currently processes approximately 100,000 tons of ore per day and has copper ore reserves estimated to be in excess of one billion tons. Functional groups within the Geology Depart¬ment (currently staffed with six professional and two support personnel) include mine geology, project geology, and hydrogeology. The primary task of mine geologists is daily preblast bench face mapping with grade and mill amenability estimates. Auxiliary duties include detailed in-pit metal distribution evaluation, mineragraphic work and flux quarry geology. Project geologists conduct explora¬tion and preliminary development projects both within and outside the Morenci district and provide support to ore reserve block modeling and geotechnical work performed by the Morenci mine engineering group. Hydrogeologists handle exploration for and development of groundwater' resources and groundwater flow modeling, mine dump leach solution penetration and recovery evaluation, and tailing dam water reclamation.

Jan 1, 1983

There are bound to be changes with age, so I should not have been surprised or disappointed when what I had considered as high ad- ventures were much fewer and more widely scattered in the last 20 years of my long and active business life. But such adventures came until I was past 80 years of age and no one could expect more than this. Frequent visits to mines in this country and Canada and directorships in Bralorne and its subsidiaries, Homestake Mining Co., Bradley Mining Co., and the Bunker Hill Co.; and Copper Range Co. and its great new White Pine mine in Michigan, lasted far beyond the usual retirement age. The least happy part of my last two decades of active life was the death or sickness of many of my old friends. Hubert d'Autremont, whose friendship no one could replace, died suddenly in 1946. Henry Carlisle and Temple Bridgeman, for many years office associates, had heart attacks that cut down their activities far too soon. Many other less intimate friends died or became ill, but I knew that with advancing years such losses were inevitable. These memoirs would be endless if they covered all of the unusual work and associations I found in the last 20 years. So I must confine the rest of my recollections to expeditions that would have thrilled any engineer at any time. Masaro Mine, Mindanao, Philippines The first of the four "high adventures" came late in 1949, when I was 65 years old. For over a month I had been discussing reported rich lead-silver-copper properties in the Philippines with Thayer Lindsley and other officers of Panaminas. A competent and agreeable "Elderly" (not as old as I was) engineer named Ward Williams had talked with Thayer about high grade mines in a remote part of the

Jan 1, 1976

By L. F. Delgado

Environmental and cost pressures sparked renewed interest in gravity separation. Industrial sands in Mexico are generally processed by screening, desliming, and flotation. Gravity separation with spirals was evaluated as an alternative to flotation in order to lower operating costs and decrease water pollution. Outstanding operating results are obtained in glass and foundry sand operations, plus a more competitive position for Mexican producers due to lower operating costs. Coal fines, generally recovered by flotation, have the same cost and environmental advantages when processed with spirals.

Jan 1, 1994

By W. E. Lindquist

Roasting of refractory gold ores has the primary goal of oxidizing sulfides and organics to improve gold recoveries prior to leaching. Commercial installations currently utilize bubbling and circulating fluidized beds. The principle of flash roasting is aimed at a more cost effective method of whole ore roasting for large throughput applications. Results of pilot plant testing and scale up to commercial design will be discussed in further detail in this paper.

Jan 1, 1993

By A. B. Fly

This paper presents the equipment and techniques developed to mine subsurface mineral deposits through 16 inch bore holes entirely by hydraulic methods. Use of this equipment for excavating large cavities in oil and water well producing zones is discussed. Results of surface experiments using high pressure jet streams of water to determine the cutting rates of materials are outlined. Various basic shapes of subsurface excavations that can be mined with the equipment are illustrated and discussed. An example of the cost of mining by this method is presented. Problems encountered in the field operations led to the development of a new explosion type slurry pumping system and related slurry handling equipment.

Jan 1, 1969

By K. Vanbroekhoven

An industrial site near the centre of a historical town in Flanders is characterized by chromium(VI) contamination of the groundwater. Since the potential for natural attenuation was not sufficient to control the groundwater plume as observed from different analyses like pH, Eh, soil oxidation and reduction capacity, the feasibility of site remediation based on in-situ bioprecipitation of chromium was examined in lab microcosm studies. By creating reducing conditions by addition of a carbon source in the groundwater, chromium(VI) can be biologically reduced to chromium(III), which can form an insoluble precipitate of chromium(III) hydroxide. Microcosms contained contaminated groundwater and aquifer samples that were collected and manipulated under anaerobic conditions. Three different carbon sources were screened for their effectiveness: molasses from sugar beet production, molasses form starch production (protamylasses) based on potato juice and lactate. The different concentrations of sugar molasses were used to determine the optimal conditions. A range of parameters was monitored at regular time intervals for a period of six months such as chromium(VI) and chromium(III), DOC, methane, pH, Eh. A rapid conversion of chromium(VI) to chromium(III) was observed for all conditions tested. However, extensive removal of chromium from the groundwater by precipitation was only achieved for a limited number of conditions. In general, lactate was found to be the most effective carbon source, slightly better than the lowest concentration of sugar molasses that was tested, which itself was more effective than molasses based on potato. Higher concentrations of molasses, although causing a steeper decline in redox potential, resulted in less effective Cr removal. Typically, the fermentation of molasses results in acidification and this drop in pH may hinder the formation of insoluble chromium(III)hydroxides. It may also be possible that certain components of the molasses form soluble complexes with chromium(III). For lactate, no significant drop in pH was observed. Following the laboratory microcosm tests, the stability of the chromium precipitates was examined by performing a sequential extraction on the microcosm materials. These were performed under redox conditions which were similar to the ones observed in the field. Since the outcome of these tests was positive, a pilot scale test was implemented in the field in April 2005. Two different substrates, the cheap waste product sugar molasses and lactate are being injected creating two different impact zones and typical parameters are monitored. Frequent re-injections were important to maintain reduced conditions and are carried out three-weekly up to now. To study the stability of precipitates formed, mesocosm socks containing aquifer material were installed in the monitoring wells and harvested at regular intervals. Results of this pilot test will be presented and compared to the laboratory results. Based on the success of this field test, a full scale process will be designed and implemented as remediation strategy.

Jan 1, 2006

By Moussa Wone, V. Nasri, F. Guimbal, D. Andre

The Magenta underground station was constructed in the heart of Paris in saturated soft soil and at shallow depth. To investigate the surface settlement and the deformation of the concrete liner, innovative techniques combined with a vast campaign of monitoring were applied. The monitoring data and a simple three-dimensional ?nite element analysis were used to assess the accuracy of the two-dimensional ?nite element model originally utilized in the design of the station. The deformation of the concrete liner was monitored using vibrating wire extensometers. Their performance was validated by the data obtained from monitoring and also by a simpli?ed ?nite element analysis.

Jan 1, 2003

By William A. Prosser, Kyle R. Ott, Philip Rice

"INTRODUCTION The existing Baltimore and Potomac (B&P) Tunnel accommodates Amtrak (National Railroad Passenger Corporation) and MARC (Maryland Rail Corporation) service between Baltimore, MD and Washington, DC and occasional local freight service. The Baltimore and Potomac Tunnel Replacement Project proposes new tunnel construction through Baltimore, Maryland along the Northeast Corridor (NEC) that maintains connections to Baltimore Pennsylvania Station. After the Replacement Project is constructed and operational, the disposition of the existing tunnel must be determined. The tunnel could be abandoned; however, considering its location in a congested downtown, alternative uses have been considered to take advantage of this unique piece of infrastructure by repurposing it. Alternative uses for the existing 140-year-old B&P Tunnel may end up being cost effective and should be considered, as the tunnel can be made accessible to construction crews for extended periods of time that will allow for efficient work activities unlike when it is fully operational. Possible alternatives include conversion for non-rail use, rehabilitation, or complete modernization for continued rail traffic. The following paper describes the four potential fates of the conceptual designs for the existing B&P Tunnel. The four concepts include: • No Build – rehabilitate to keep the tunnel operational. • Abandonment – complete or partial sealing of the tunnel. • Adaptive Re-Use –repurpose the tunnel with sustainable building practice. • Full Rehabilitation and Modernization – bring to current fire-life safety aspects. Of the four concepts, only the no build addresses maintaining the tunnel while it is under traffic. The remaining fates address the existing tunnel after the new tunnel is operational and railroad traffic has been diverted to it. Development of these conceptual designs were provided in a concept design study (Parsons Brinckerhoff/Parsons, 2015) that supports the National Environmental Policy Act (NEPA) review process for the Project, which includes evaluation of possible alternative uses of the existing B&P Tunnel."

Jan 1, 2016

By T. M. Ruff, W. G. McCoy, M. J. Beus, S. Iverson, W. Hasz

Technology to enhance safety during mine hoisting has been developed by researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health. Assessment of current hoisting technology suggests that monitoring conveyance position and load directly from the skip or cage top offers several significant safety advantages. Wireless data transmission schemes and a package consisting of sensors, batteries, and a charger mounted on the wire rope and skip have been developed. A state-of-the-art automated hoisting test facility was constructed to test the concept in a controlled laboratory setting. Field tests in a full-size shaft are underway.

Jan 1, 1999

By Gary R. Krieger

Baseline Risk Assessment: - Data Collection and Evaluation - Exposure Assessment - Toxicity Assessment - Risk Characterization Lead - Problems and Pitfalls: - Sources - Pathways - Receptors - Toxic Endpoints - Modeling Options - Health Based Clean-Up Options

Jan 1, 1990

By John A. Organiscak

The Bureau of Mines evaluated a new dust control technique for longwall personnel required to work at the tailgate end of the face. This technique utilizes a water-powered scrubber to clean a portion of the face air, which is discharged behind a brattice partition at the working area. Laboratory simulation of this system in a wind tunnel resulted in average efficiencies greater than 70 pct with system efficiency directly related to scrubber quantity. Underground evaluations indicated a similar direct relationship between scrubber quantity and system efficiency. Gravimetric measurements of respirable dust made during these underground evaluations resulted in average protection efficiencies ranging from 30.7 to 42.5 pct with increasing scrubber air quantity.

Jan 1, 1983

By S. K. Kawatra

In order to meet federal air pollution guidelines, it is necessary to remove a considerable quantity of sulfur from many North American coals. This may be accomplished by oxidizing the sulfur to water soluble forms, followed by washing the coal. Selective oxidation of the various sulfur forms can be accomplished through the use of a variety of types of bacteria. In this paper, the various bacteria and their requirements are described, and processes using bacteria to remove coal sulfur are discussed.

Jan 1, 1987

By M. O. Woodburne

The Mojave Desert province is comprised of a diverse group of mountains that range in elevation from about 2,000' (600 m) to 3,000' (900 m), separated by tracts of alluvial cover. The province is bounded on the southwest by the San Andreas fault, on the north by the Garlock fault, on the east by the Death Valley- Granite Mountains fault. Rocks preserved in the Mojave Desert Province collectively record a rich assemblage of Precambrian crystalline basement' ranging in age from ca. 1.8 to 1.35 Ga, upper Precambrian and Paleozoic Cordilleran miogeoclinal sediments and platform rocks, Mesozoic backarc and interarc shallow marine and continental sequences, locally emplaced Permian- Triassic syenitic plutons, extruded hypabyssal volcanic rocks of the ?Jurassic "Sidewinder Volcanic Series," and regionally intruded late Mesozoic granitoid batholithic rocks (Dokka et al., 1988). The Mojave block apparently was a high-standing element for much of the early Tertiary, with strata of Late Cretaceous or early Tertiary age preserved only on its margins. Beginning about in the late Oligocene an intense episode of regional north-south extension was developed in a roughly east- west trending belt that traversed the central part of the province. This extensional belt has been termed the Mojave Extensional Belt. The extensional regime lasted from about 22-17 Ma, and is generally divided into two phases. The first, from about 22-20 Ma records intense extension via the activity of crustal-scale, simple shear, low- angle normal faults, high-angle normal faults, and extensional fracturing, along with intrusion of intermediate to silicic volcanic rocks, including episodes of explosive volcanic activity. The Peach Springs Tuff, a major regional marker unit that extends across the Mojave from Arizona to about Barstow, forms an effective stratigraphic lid on the extensional interval, (i.e., is not rotated) and is dated isotopically at about 18.5 Ma. The extensional episode was followed by an interval of high- angle normal faulting and dike emplacement from about 19 to 17 Ma, and was accompanied by at least local uplift and volcanism. Most volcaniclastic and epiclastic sedimentary units of the central Mojave block post-date the interval of extension and normal faulting, and occur as a complex of marginal alluvial and more interior lacustrine facies that formed as recently as late Miocene (ca 13 Ma). Local sequences (e.g., Lava Mountains) record deposition up to about 8 Ma, but there appears to be a regional "gap" from then until at least local successions record Pleistocene deposition. Magnetic and isotopic age studies indicate a complex history of crustal rotations, distributed across a number of discrete domains, during the past 10 Ma. Some of the youngest volcanic and geomorphic features apparently developed at "holes" formed at the edges of rotated blocks.

Jan 1, 1995

By C. W. Matthews

Introduction Screening is defined as a mechanical process which separates particles on the basis of their size and their acceptance or rejection by a screening surface. The key element in this method of particle sizing is obviously the screening surface, the medium that contains the apertures for the passage of the undersize material. This surface must be strong enough to support the weight of the material being screened, flexible enough to yield to the vibrating force applied to it, yet light enough to provide a reasonable ratio of open area to attain a practical through- put. To balance all of these factors is difficult enough. The problem is compounded, however, because screening media are made in a great variety of types, shapes, sizes, and materials of

Jan 1, 1985