Search Documents

By S. A. Braley

Water is our most important natural resource, for without it there is no life. It is also the principal natural resource for all manufacturing processes, in particular for the development of power. For these reasons it is essential that water be protected and conserved, with the realization that its quality 18 as important as the water itself. A significant factor in the quality of ground water is the mining of coal -- that other main ingredient of Power. In the mining of coal it is necessary to disturb the geological strata overlying or adjacent to the coal seam. This procedure not only releases water from water-bearing strata or underground aquifers but also exposes other minerals which eventually become the source of pollution or deterioration of the released water as well as of the surface stream into which It is discharged It is then evident that in attempting to utilize one essential natural resource there is degradation of the quality of the other. Many selfishly assume that the principal function of a stream is fishing and recreation, but the real function is the support of industry and agriculture upon which civilization is dependent.

Jan 1, 1959

By B. Seymour

The National Institute for Occupational Safety and Health (NIOSH) is conducting research to develop safe practices for the use of shotcrete as ground support in underground mines, particularly mines operating in weak host rock. As part of this research, tests were conducted with a commercial poly-fiber reinforced shotcrete mix to develop a practical means of measuring shotcrete adhesion strength. Full-scale tests were conducted in a test frame equipped with concrete panels having three distinct surface roughness profiles. Adhesion test fixtures either embedded or epoxied in the shotcrete were overcored into the underlying concrete, and direct tensile tests were conducted to determine the bond strength of the shotcrete cores to the substrate after a selected shotcrete curing interval (1, 3, 7, 14, 28, or 90 days). Measured adhesion strengths typically ranged from 0.5 to 2.0 MPa depending on the curing age of the shotcrete samples. This paper presents the results of these tests, describes the portable test system components, and addresses some of the design issues encountered in the development of a rugged and reliable method for determining shotcrete adhesion strength in underground mines.

Jan 1, 2010

By R. Michael Craig

The flood basalts of the Columbia Plateau in eastern Washington State are under investigation for suitability in siting a deep geologic repository for high-level radioactive waste. To support safety and feasibility evaluations of the proposed repository construction and operation, an assessment is necessary of the potential for inflow of groundwater to the repository excavations from the surrounding saturated rock. Preliminary estimates of inflow are presented using simple models appropriate to the current understanding of available data. Both normal and bounding analyses are presented.

Jan 1, 1986

By Randhir S. Sehgal

After some decades of lying low and being treated as a second rate fuel, coal is back in the news. Production is rising. Predictions are for an ever expanding use, and they differ only in their rates of increase. Even the FBI is involved in trying to stop fraudulent sales of non-existent coal lands and leases to the innocent. In short, we have a nearly chaotic boom on our hands. Obviously our energy production base is in the process of undergoing a major shift, and the process will present many problems. However, there is little doubt that the industry has the basic strength and organization to be able to deal with the new issues that will arise as a result of these shifts in production and use of coal. After all, it does produce nearly 800 M tpy now, and coal is the single biggest fuel for generation of electricity. This role of coal is illustrated in the table below, which shows the coal equivalent quantities of various fuels used in the production of electricity.

Jan 1, 1980

By Arland R. Krueger

You have asked me today to tell you how quarried stone is meeting the challenges of contemporary architecture. The new position of stone, the oldest building material, in contemporary architecture, was described to me very concisely the other day by a very distinguished avant garde architect. He said rather wryly, "Do you know, if quarried stone had only just been discovered, we would all be calling it the most miraculous of all the modern miracle building materials." His prognosis was, I believe, much more than a witty quote. It echoes the surprise and. enthusiasm with which a considerable segment of the architectural profession is rediscovering stone as a most modern building material that offers unsurpassed values in beauty and practicality - well deserving of the term "miracle".

Jan 1, 1960

By Adrian Brown

The primary method of slope stabilization is ground water-control. Recent research has established the properties which slope materials must exhibit in order for stabilization measures to be feasible, but there is little guidance in the literature about suitable field tests to develop the parameters needed for this evaluation. This paper presents a proven method for large scale testing which allows an evaluation of the feasibility of ground water pressure control in a reasonable cost and time frame. Methods of performance and analysis of the test are presented, and the method is illustrated by reference to case examples.

Jan 1, 1984

By Asa Weber

With continuing pressure from stockholders not only to maintain but to increase mineral revenues, producers have increased plant capacity. Depressed mineral prices have accentuated the trend toward higher production rates to maintain consistent cash flow, and these same trends have promoted the development of large-scale processing equipment. In addition to the need to handle increased throughput, larger flotation equipment can result in decreased capital-equipment and operating costs. The development of larger column and conventional flotation equipment relies, in part, on suitable scale-up procedures. To properly scale-up large flotation cells and columns, certain constraints and design parameters must be taken into consideration, including velocities in the vessel, residence time, solids suspension, and lip loading. This paper will review the design constraints and scale-up criteria for WEMCO® flotation cells. Scale-up criteria are augmented with computational-fluid- dynamics analyses and high-speed imaging techniques, as well as multiple regresesion analysis of in-plant operational data.

Jan 1, 1999

By E. M. Cukrowska

The evaporative pan complex consists of two adjacent seasonal pans. These pans carry an exceptionally high salt (TDS) load due to over 50 years of effluent discharge via the pipeline from mines. The nutrient, heavy metal, radionuclide load in the water and sediments of the pans are very high affecting groundwater around the pans. The groundwater in the region contains TDS > 40 000 mgl-1 and sulphates > 7000 mgl-1, whereas groundwater in areas assumed to be unpolluted by mining activities have TDS < 500 mgl-1 and sulphates < 200 mgl-1. The extent of continuity between the pans and the groundwater is unknown, although there appears to be seepage of contaminated groundwater into the river system.

Jan 1, 2006

By D. W. Agers

This paper is an extension of previous work evaluating a new extractant, LIX®-64, for recovery of copper from dilute acidic solutions. Large scale pilot plant operations have confirmed the technical and economic feasibility of the process and, with minor exceptions, scale up parameters obtained by previous laboratory work. Operating problems encountered in the pilot plants are discussed. Design parameters for-scale-up to commercial plants are presented and discussed along with a revised capital cost estimate. The future pilot program is discussed, including minor design changes and the effect of entrained organic on dump leaching efficiency.

Jan 1, 1967

By Juan H. Rojas

The Chuquicamata mining and metallurgical complex is the main division of CODELCO-CHILE. Its comparative advantage in the world of primary copper producers had deteriorated severely and, consequently, its top management launched an extensive modernization plan. This paper shows how Chuquicamata recovered its position as a low-cost copper producer and is now well positioned to face the end of this century, as far as competitiveness is concerned. It also shows the company&apos;s vision for the )(XI century. Given the volume of its ore reserves, one possibility is expanding the sulfide production line capacity, while in the case of the oxide production line, ore reserves are limited so that there is a need to maximize the effectiveness of both organization and technology use. A final consideration has to do with the balance of supply and demand. Most observers of the copper market agree that supply is growing faster than demand. On the other hand, copper is facing severe environmental problems, especially in the piping business, plus the usual threat of substitution. Nevertheless, copper producers are making very weak efforts to defend the market and increase copper consumption through the promotion of new uses of the metal. This issue is crucial and must be considered if copper producers want to maintain a profitable market.

Jan 1, 1998

By Omar A. Muhtadi, David A. Milligan

7.1 INTRODUCTION The circulating fluid (generally an aqueous cyanide solution) is the major active component of heap leaching. This solution extracts precious metal from the heap and is then processed to recover the precious metal. The solution continuously recycles through the heap to recover more precious metal. With each cycle through the heap, water and chemicals are lost. Make-up water and chemicals must be added to balance losses from evaporation, seepage, entrainment, and chemical reaction in the heap, as well as any other processing losses. Adding more water than needed can result in a build-up of water as inventory in the various ponds and can eventually require that water be discharged from the operation. This is an extremely undesirable condition, and can often be very expensive in both investment in water treating facilities and operating costs. Most heap leach facilities operate under a zero discharge permit; thus, a situation requiring water discharge can result in permit violation. Chemical solution control must be managed to maintain the optimum pH, dissolved oxygen content, and cyanide content, while preventing "scaling". Calcium-based precipitation is a common scaling problem in mill reclaim waters. A buildup of these deposits can result in severe reduction of water flow, loss of pump efficiency and eventual interruption in metal production. In addition, problems of plugged sprinkler heads, blinded leach pads and fouled carbon (in carbon recovery systems) can be and often are experienced when scale control is not maintained. The remainder of this chapter discusses chemical solution control and scaling prediction/prevention in the context of a "closed" system. Sizing of ponds to accommodate precipitation and runoff, collection systems, and other similar design considerations are not discussed here. These topics are deferred to later chapters, e.g. Chapter 10 considers design of collection systems while Chapter 12 discusses pond sizing. 7.2 CHEMICAL CONTROL Chemical composition of the circulating solution must be controlled by the operator if the heap leaching process is to be successful. The primary or essential chemical control parameters in any heap leaching operation are:

Jan 1, 1988

By Scott G. Britton

In this chapter, I shall discuss railroad con¬struction for modern underground coal mines. Because men, materials, and supplies are being moved more often and farther by rail, the ef¬ficient and safe construction of the system takes on new importance. Most large coal mines are opting to use track haulage over other support transportation systems because of cost, ease of installation, reliability, and other factors. En¬gineers tackling the problem of designing such a transportation network must be aware of all the steps required for an effective transportation system design. This chapter discusses all aspects of efficient trackwork construction. The areas covered in¬clude design factors, laying the track, installing turnouts and switches, and installing trolley wire. Each area includes a description of the steps needed to complete the work.

Jan 1, 1983

By Richard P. Killmeyer, Carl P. Maronde, W. W. Wen, Peter J. Suardini

Under a cost-shared Department of Energy contract, awarded as part of the Coal Preparation Program&apos;s High Efficiency Preparation subprogram, Custom Coals International will be installing and testing a 227 kglhr micronized-magnetite cycloning circuit in PETC&apos;s Coal Preparation Process Research Facility. The project includes the design, construction, testing, and decommissioning of a fully integrated circuit complete with feed coal classification to remove the minus-30-micron material, dense-medium cycloning of the 300 by 30 micron feed coal using micronized magnetite (<10 microns), and medium recovery via drain & rinse screening and various stages and types of magnetic separation. This paper will describe the micronized-magnetite beneficiation technology and the scope of work for this project including an update on the status of the project, the circuit, and the proposed test plan.

Jan 1, 1995

By Raymond E. Langen

Uranium exploration in the Powder River Basin of northeastern Wyoming has been intensive since 1966 and in 1968 produced significant discoveries of reduced uranium ore by Humble Oil & Refining Company and others. Substantial reserves have been established in the area. High-grade carnotite ore was discovered in 1951 near Pumpkin Buttes in the central part of the basin (Fig. 1). Other mineralized areas were soon established from Pumpkin Buttes south to Monument Hill and Box Creek. Total production from these shallow oxidized deposits in the lower Eocene Wasatch formation was small. The AEC reports total production of 520,000 tons of ore averaging 0.19% U3O8. The authors are indebted to many people within Humble Oil & Refining Company and Esso Production Research Company for their assistance and guidance. SUMMARY AND CONCLUSIONS The Highland ore deposit, discovered in 1968, is a large uranium occurrence located in the southern part of the Powder River Basin. Uranium mineralization consists of sooty, black uraninite and coffinite coating sand grains and is concentrated along the margins of Tertiary fluvial sandstones. Uranium was transported by oxidizing solutions roving through the buried sandstones and spreading into less permeable channel-edge sandstones to form typical rolls and tabular deposits. Unaltered sandstones are light gray to gray-buff where the sandstones have been oxidized, the colors are various shades of red, yellow, and yellowish brown. An Oligocene tuffaceous source for the uranium is proposed; however, leaching of the arkosic and tuffaceous host sediments may also have provided a source.

Jan 1, 1971

By Scott G. Britton

This chapter is concerned with the construction of the dynamic component of belt haulage systems. The dynamic system includes the belt line and tailpiece extension and retraction movements in a production system where mine management is continually placing the belt in the most effective operating position. Correct installation of the belt and tailpiece during an extension is very important for many performance reasons. Two of the most important reasons are to eliminate spillage and safely operate the belt line. This chapter is divided into three major discussions. The first discussion looks at analyzing the parameters of effective belt line construction. This includes a review of the parameters and management tools needed for proper scheduling of a move-up. The second major discussion topic centers on efficient procedures for a belt line extension. Topics such as site preparation, tailpiece breakdown and setup, stringing the belt line and structure, plus operating and maintenance tasks needed after the belt line is installed and running, are covered. The third discussion presents a list of conveyor and conveyor component manufacturers who provide services and products to the coal mining industry. Again, any discussion on underground haulage systems must generalize much of the site specific design approaches to be practical. This text will mention, where applicable, some of the alternatives available to construction engineers in designing belt line systems.

Jan 1, 1983

By D. A. Norrgran, J. N. Orlich

Described is the application of high- intensity magnetic separation throughout the spectrum of industrial minerals. Performed either wet or dry, the separation has application in both the recovery and concentration of value minerals and in removing deleterious mineral constituents. The various types of magnetic separators along with the design and operating parameters relative to separation response are characterized. The characteristics of specific minerals to magnetic collection and the production of high-grade concentrates are described. Laboratory, pilot-scale, and plant studies carried out on a variety of industrial minerals have demonstrated the effectiveness of magnetic separation as either a primary or a secondary unit operation to achieve product quality.

Jan 1, 1987

By Eugene E. Brucker

In recent years, there has been increased interest in construction problems presented by karst topography. Twenty-five years ago, karst areas were by-passed for development. Today, the high cost of land and population pressures are requiring utilization of karst areas. Areas exhibiting karst features can be satisfactorily developed so that construction can proceed in a normal manner; or the areas may be left undeveloped and the underground drainage system abused by improper use causing or contributing to structural collapse, excessive erosion, and a grave threat to the stability of land development and the environment. The term "karst" is a comprehensive term applied to areas underlain by soluble rock that possess a topography formed chiefly by the dissolving of rock and the diversion of surface waters to underground routes. There are four features which contribute to the maximum development of karst. 1. A soluble rock, preferably limestone, must be present at or near the surface of the ground. Occasionally, dolomite will suffice.

Jan 1, 1970

By R. R. Young

Prior to 1903, the world&apos;s supply of sulphur was primarily from surface deposits in Sicily. The discovery of the first salt dome sulphur deposit in 1867 and successful development of the Frasch process for recovering the sulphur resulted in a large part of this essential element being supplied from these mines since 1920. Although the basic process is the same today, engineering and technological developments have evolved to allow its application under many adverse conditions. These and other challenges for the industry in today&apos;s environment will be discussed in the paper.

Jan 1, 1979

By I. Michalakis

A geological and geophysical study was con-ducted at the area of Stylos, Hania in order to study the possible mechanisms of saltwater contamination. A new detailed geologic map in scale 1:5,000 was combined with the results of a time lapse geophysical survey using seismic and electrical methods. A fault system in the N-NE direction possibly favors the saltwater intrusion.

Jan 1, 2006

By J. R. Palmes

Three coal samples, selected out of eight with well characterized surface properties, were used in flocculation tests and synthetic mixture of coal and silica was used in the selective flocculation experiments. Coal wettability and flocculant type were found to have a strong effect on the flocculation results.

Jan 1, 1993