Search Documents

By John G. Groppo, Bonnie Webb-Groppo

INTRODUCTION The first portion of this chapter is concerned primarily with the contamination aspects of fine coal cleaning that include both the solids and water discharged as waste products after coal preparation. Topics include characteristics of the water and solids, changes that occur to both of these phases during use and after impoundment, as well as the impact that these changes have on unit operations and the environment. Attention is also given to the formation of acid mine drainage and treatment options that may facilitate reuse of the water. The second part of the chapter analyzes the problem of air contaminants from coal preparation plants including analysis of air pollutants and control methods. An overview of air quality regulations is also presented; most provisions have little or no applicability to coal preparation plant operation but are presented to provide an understanding of end-user constraints. The final part of the chapter emphasizes the long-range problem of refuse disposal and control. An overview of characterization, maintenance, and control of the refuse area is presented, as well as design guidelines. A brief review of stability analysis procedures is also included. PREPARATION PLANT WATER Characteristics of Makeup Water for Coal Preparation There are few specific rules governing the quality of makeup water used in coal preparation processes.'" It is generally accepted, however, that the solid matter content should be less than 5%. The solids concentration in plant makeup water typically varies between 0.25 to 0.9 lb per gal (30 to 110 g/L) and may reach concentrations as high as 1.7 lb per gal (200 g/L). The water used in coal preparation is usually obtained from one or more of the following sources: public supplies, rivers and streams, canals, mine water, and wells. In most cases, water is obtained at the lowest cost including any necessary treatment. A major portion of the recirculated water is clarified by thickeners and settling ponds to remove fine coal and clay particles. Sufficient water is generally available to meet the needs of coal preparation in most areas. It has been estimated that approximately 65 to 70% of the makeup water used in a coal preparation plant comes from surface sources. It is important to note that a variety of substances are commonly found in natural water supplies, whatever the available source may be (Table 11-1). Excessive concentrations of some of those substances can have an affect on plant performance; the effect of specific contaminants on unit operations will be discussed

Jan 1, 1991

By R. W. Bartlett

Computer deterministic models for predicting the time dependent extraction of copper by leaching fragmented rock (both in situ and heaped or piled) have been presented in the last two years by Bartlett1, Braun, Lewis and Wadsworth2 and Roman and Co-Workers.3 All of these models involve aqueous diffusion within the pores of the rocks from which the metal is being extracted. The rate of chemical dissolution of the ore mineral within the rock will also affect the kinetics in the case of sulfide copper ores and some of the more refractory oxide copper ores. Simulation is also needed for fine grain disseminated gold ores and low grade uranium ores that may be heap leached. The development of such leaching models has two major purposes: First, extraction estimates must be made for tong time periods particularly for situations where laboratory and field tests either cannot be made or where there is insufficient time for field testing. Second, the results of simulated leaching should indicate the relative importance of the extraction controlling parameters and, thereby, provide a better understanding of the complex leaching phenomena on heaped material being leached, and guide further experimental work.

Jan 1, 1974

By Edgar A. Scholz

The purpose of this paper is to make a comparative cost analysis of domestic and foreign exploration projects which developed into mines during the 1960-1974 time period. A total of 18 mining companies, American and Canadian, were approached to solicit cost data on domestic and foreign exploration projects which developed into mines. Only 20 percent of the companies to which questionnaires were sent made data available. Several companies answered negatively, informing us that they would have difficulty in attempting to sort our costs. Some companies were usable to release cost details. It is comforting, however, to realize that some of the non-contributing companies expressed eagerness to hear the findings of this paper. Inasmuch as the data available on exploration expenditures is, in some cases, somewhat uncertain and that no two mining companies follow the same system of cost allocations, the results obtained in this analysis should he interpreted as trends of a general character.

Jan 1, 1976

By R. H. Derammelaere

With renewed interest in coal slurry pipelines in China, Indonesia, Australia and Canada for electric generation, it appears worthwhile to update the relative economics of transporting coal by slurry pipeline. Three slurry pipeline technologies are evaluated for the commercial transportation of 3.0, 6.0, and 9.0 million tonnes per year (MMT A) example cases, over distances of 250 km, 500 km and 1000 km.

Jan 1, 1998

By Sun K. Kim

Hydrometallurgical processes are not free of environmental regulations. A clear understanding of the regulations under which the minerals industry operates delineates processing requirements at early stages. This paper deals' with federal environmental regulations with emphasis on the hazardous waste regulations promulgated in May, 1980. The procedure of EP toxicity test and an example of the test are described. Brief account is given of the current trend and future outlook of regulations.

Jan 1, 1982

By Steven J. Kirk

In the past decade, many hardrock surface miners have revegetated dumps and tailings ponds to allow those waste disposal areas to blend more easily with the surrounding landscapes. Efforts have also been made to more creatively use the flat land resulting from the disposal of overburden and tailings. However, the mines which serve the best post-mining land uses are those that have been preplanned to incorporate such end uses. To more fully explore such a philosophy, interdisciplinary team from The University of Arizona conducted a study during 1974 and 1975 of six open pit copper mines in the Santa Cruz River Basin south of Tucson, Arizona for the purpose of investigating both interim and end-use possibilities for mine waste disposal areas. Among other reasons for the study, it was felt that alternatives for such waste areas would be more socially acceptable than barren dumps or tailings ponds. The team, known as the Mines Project Group, consisted of architects, engineers, and hydrologists. As it would have been economically infeasible to move the existing waste rock dumps or tailings ponds, preplanning was limited to the disposal of waste generated after the inception of the project. To better present their concepts, architecture professors Kenneth Clark and Fred Matter constructed a large-scale cardboard relief model of the mines and the surrounding Santa Cruz River Valley (1). The model was built at a scale of 1:12 000 (1 in = 1000 ft) with 30.48 m (100 ft) contour intervals and covered an area of 40.23 km by 32.18 km (25 miles by 20 miles) in scaled area. The mines being studied were cut into the model, but the proposed waste dumps and tailings ponds were built separately so different disposal configurations could be evaluated.

Jan 1, 1980

By Edwin S. Smith

One of the many responsibilities of mining engineers and mill superintendents is to provide for the safe and economic disposal of wastes (or tailings) remaining after a mineral has been extracted from an ore. The cost of disposal of these tailings exerts a considerable influence on the minimum grade of ore extracted from the mine. It varies to a great extent with each project and is dependent on many diverse factors, such as the local topographical, meteorolgical, geological and seismological conditions together with the applicable water pollution laws of the area. The process used to extract a mineral from an ore determines the physical characteristics of the tailings and thus is one of the more important factors to be considered when planning disposal facilities. Today's trends .in ore-processing operations complicate the problems of waste disposal: recently developed extraction methods result in the production of finer tailings, the use of lower grade ores produces greater volumes of wastes, while the enhanced land values in the vicinity of industrial plants preclude the former practice of spreading wastes laterally and force the expansion of waste desposits upwards to greater heights. The frequent occurrence of stability problems in waste deposits indicates that many mining organizations may not be employing current soil mechanics concepts and practices. One of the most spectacular, and often most disastrous, types of tailings dike failure is that resulting from liquefaction of the fine particles combined with a breach of the main retaining dike.

Jan 1, 1967

By Glenn A. Hazen

Longwall mining is the preferred method for removing underground coal since a larger amount of coal can be removed faster and with less waste when compared to the room-and pillar type mining. Thus, the coal tonnage removed each year by longwall mining methods has increased dramatically. However, a high extraction rate results in surface subsidence which has adverse effects on the environment and on surface structures. Predictions of structural damage are dependent on the magnitude of the expected horizontal strains. Three methods for predicting subsidence characteristics are considered in this paper: the graphical method, the profile method, and the finite element method. All three methods can be used to predict ground movements and horizontal strains. However, the finite element method, which takes into account the structural properties of the stratigraphy and equilibrium of the overburden, is theoretically the more logical choice for use in subsidence prediction.

Jan 1, 1987

By W. C. Carter

In mid 1978 Inland Cement Industries Ltd. brought on-line their new one million megagram (Mg) per year cement plant at Tilbury Island, Delta, British Columbia. The Plant--Its Philosophy of Design The design of this plant began in 1974, at the beginning of the rapid rise in petroleum costs later referred to as the "energy crisis". The trend in fuel costs was clear, so one of the basic criteria for the selection of process equipment was high thermal efficiency. Throughout the process of selection of materials handling and process equipment, energy consumption was a factor in decisions. A second factor which influenced the design of the plant was its location on navigable water. The plant is designed to make maximum use of this means of transport to minimize transportation costs. All raw materials (and some fuel) are received by water, and a major portion of the cement and clinker is sent out by barge. Extensive modern dock and material handling facilities were provided to accomplish the shipping and receiving functions. A plant meeting stringent environmental regulations was the third major factor which formed the basis for design. To meet this requirement, all storage facilities had to be covered, 53 bag type dust collectors were applied throughout the plant, and materials handling equipment was designed to minimize dust and spillage.

Jan 1, 1979

By Douglas M. Deason

Swelling clays, such as montmorillonite, contribute significantly to the poor dewatering and consolidation behavior of the Florida phosphate clay wastes. Understanding and to a degree, control of the forces which cause the swelling behavior may aid in supplying a solution to this problem. The technical feasibility of utilizing control- led dispersion for aiding dewatering of phosphatic slimes was investigated. This technique is based upon inhibition of swelling and self-dispersing tendencies of the montmorillonite clays by dispersing the solids in electrolyte solutions. Through this process, significant improvements in settling rates and sediment solids content were achieved in both pure clay systems and on simulated phosphate slimes.

Jan 1, 1983

By Bernie W. Martin, Jesus Schabib

The East Side Access (ESA) Project in New York will be the largest tunneling project ever undertaken by a US railroad. The objective of the ESA project is to connect the Long Island Rail Road (LIRR) Main Line and Port Washington Line in Queens to Grand Central Terminal in Manhattan. The Project is divided into two distinctive segments: Manhattan and Queens. The Queens segment is subdivided into two major components; cut and cover tunnel construction and bored tunnels. The bored tunnels in Queens consist of five tunnels driven from a launch shaft and traverse a railway storage yard, Sunnyside Yard and terminate under the multitrack mainlines of Amtrak and LIRR at portals in the heart of Harold Interlocking where1200 trains pass every day. The soil consists of remnants of glacial till moraines and of outwash and till deposits of inter layered gravel and fines, with the occasional boulders and cobbles and with a high ground water table. It is anticipated that a Pressurized Face Machine, either slurry or Earth Pressure Balance equipped with roller disks to mine the boulders encountered as well as the mixed face, will be used to mine the tunnels. One pass reinforced concrete gasket bolted liner will be used. The cut and cover construction consists of an approximately 21.3 m (70 feet) deep excavation supported by slurry walls and jet grout columns. The slurry walls, in combination with overlapping jet grouted columns, are installed to top of rock forming a closed bathtub to control external groundwater drawdown. Maintaining the groundwater level near its original elevation is of paramount importance in order to prevent undesirable settlements and migration of groundwater that could be contaminated. Mitigation measures to prevent the migration of nearby plums are contemplated for all types of tunneling and excavation work in this site of the ESA project.

Jan 1, 2001

By R. E. Coleman

Infrared spectroscopy, employing the internal reflection method in conjunction with solvent extraction techniques, was used to study surface reactions between aqueous potassium ethyl xanthate and both sphalerite and precipitated zinc sulfide each activated with aqueous copper sulfate. It was determined that reactions occurring on the sphalerite and zinc sulfide surfaces produce the reaction products ethyl dixanthogen and cuprous ethyl xanthate, some of which are ad¬sorbed on the mineral surfaces. According to infrared spectra showing the reaction to form these compounds, the ratio of cuprous ethyl xanthate to ethyl dixanthogen adsorbed is directly related to pH of the flotation solution.

Jan 1, 1967

By Ren Bryce

The ninth annual Mineral & Metallurgical Processing Division (MPD) student poster contest was held in February at the SME Annual Conference & Expo in Minneapolis, MN. A total of 33 students presented their work at the contest. The competition began in January when the students submitted a one-page abstract for judging. In February, they prepared and presented a poster that explained their research. A panel of judges went to each student and listened as the students explained their research in five minutes. The students worked hard at their research and then set aside time to complete all the necessary steps to enter the contest. The MPD recognizes the effort required to enter and, as a result, provides monetary rewards to all participants. As in past years, there are separate levels of competition for undergraduates and graduates, and the prizes are designated accordingly. At the graduate level, first place receives $1,000, second place $500, third through seventh $200 each, and all others $125 each. At the undergraduate level, first place receives $1,000, second place $500, third place $250, and all others $125 each.

By A. Heriba

Cyanide is highly toxic to humans and other organisms. Concentrations of RCN as low as 0.05 ppm can be lethal to fish (Scott and Ingle', 1981). In wet climates and in colder climates where natural degradation is slow, it is becoming mandatory to destroy cyanides in effluents before they can be discharged. The disposal of spent gold ore as tailings from cyanide heap leach processing facilities is a matter of concern to the public, the mining industry, and regulatory agencies. South Dakota mining laws and regulations require that spent ore be neutralized to a suitable level with respect to cyanide before disposal (Durkin, 1990). To safeguard the environment and protect ground-water and surface-water supplies adequately, a reliable test is needed to determine the amount of cyanide in the solid spent ore.

Jan 1, 1993

By C. D. Hebert, T. Gregor, M. Ghazi, G. J. E. Kramer

This paper describes the recent application of gasketed, precast concrete segmental lining design that has improved tunneling productivity and quality. The speci?c segment arrangement includes: six-piece ring with equal 60 degree gasketed segments, juxtaposed key and counter-key segments, trapezoidal and parallelogram shaped segments, inclined and skewed radial joints and plastic circumferential joint connectors. This allows rapid, but accurate ring erection, reducing mine cycle times. The design avoids cruciform joints, minimizes potential gasket damage and eliminates the need for separate left and right ring molds. The implementation on the Los Angeles ECIS and NEIS sewer projects is described.

Jan 1, 2003

By James J. Scott

Shale formations are the Nemesis of the Mining Engineer. Shales react to changes in environment in the most unusual and unpredictable manner. Increase in temperature may cause spalling, increase moisture and compression induced fractures may occur, and if a full face is exposed it may deteriorate due to atmospheric exposure. Combine only small amounts of shale in layered fashion with hard brittle competent rock and the whole structure may be fractured and fail due to stresses generated in and around the shale. In this paper the author will discuss failure mechanisms encountered under various field conditions and remedial action which may be employed by the engineer.

Jan 1, 1969

By J. Appleby

This paper reviews earlier in-plant testing at the Sidbec-Normines pelletizing plant at Port Cartier, Quebec, Canada. It describes the result of the more prolonged use of coke breeze during recent months and in addition, the effects of varying dolomite and coke additives upon the metallurgical properties of the pellet production have been studied. Mention is also made of some brief test work carried out to use peat moss as a carbonaceous additive to the pelletizing process and in particular the plans for future work in this respect. Earlier laboratory pot-grate test work had indicated that a production rate increase of between fifteen and twenty percent was a practical possibility, or alternatively that the plant could be run at design rating with significantly lower energy consumption. These energy reductions were of the order of ten to fifteen percent for fuel and main process fan power respectively. The physical and metallurgical pellet properties for both blast furnace and direct reduction furnace use were little affected by the production rate increases, and were actually somewhat improved when practicing maximum energy conservations. Pellet properties could be further improved by not extracting the maximum energy economy. Two phases of carefully controlled in-plant testing were run to assess the effect of energy conservation under plant conditions. These two phases of testing confirmed that an overall fuel saving of approximately fifteen percent could be realized, with a reduction in the Bunker C oil consumption of about forty-five percent, and a reduction in main process fan power of approximately ten to fifteen percent. The present scope of work is aimed at establishing the use of varying levels of coke addition up to about one percent under normal plant operating conditions.

Jan 1, 1980

By J. S. Hastings

Tertiary calc-alkalic to alkalic rocks of the Little Rocky Mountains in north-central Montana host low-grade heap-leachable gold-silver deposits being mined by Pegasus Gold Corporation. Total production from 1884 through 1985 is estimated at 22,625 kilograms (727,414 ounces) of gold. This includes 10,774 kilograms (346,400 ounces) recovered by Pegasus between 1980 to 1986 from 20,318,000 tonnes (22,396,000 tons) of ore grading 0.960 grams of gold per tonne (0.028 ounces per ton). Silver production during this latter period was 24,556 kilograms (789,500 ounces), but reliable silver statistics prior to 1980 are not available. Ore reserves as of January 1, 1986, were estimated to be 35,380,800 tonnes (39,000,000 tons) grading 0.720 grams per tonne (0.021 ounces per ton). Present ore production is 5,533,920 tonnes (6,100,000 tons) per year at a 0.45 to 1 waste to ore strip ratio. Current annual metal production is about 2,644 and 5,288 kilograms of gold and silver respectively (85,000 and 170,000 ounces of gold and silver respectively). The Little Rockies were formed by a calc-alkalic to alkalic magma penetrating through the Precambrian basement into the overlying Paleozoic and Mesozoic sedimentary rocks. This intrusive center is Dart of the Central Montana Alkalic Province, a region comprised of twelve separate intrusive centers aligned in a northeast trending belt measuring 200 by 400 kilometers (124 x 248 miles). The ore deposits are structurally controlled epithermal systems which vary from deeper narrow veins to shallow, wide, low-grade stockworks, breccias and intensely fractured "sheeted" zones. The shallow types are now being exploited. Primary mineralization consists principally of gold and silver associated with pyrite, native gold and silver, sylvanite, calaverite, and hessite. Alteration is broadly classified as weak argillic. Pyritization, kaolinization, silicification and feldspathization are the dominant forms of alteration. Fluorite is a common hydrothermal gangue mineral.

Jan 1, 1987

By R. S. Shepard

A quick glance at a-portion of the title of this discussion -'Rolling With The Punch" may immediately lead you to assume that I am about to expound on the so-called manly art of self-defense. So that you will not have been misled entirely we will devote our considerations to a far more important art and if I may, I should like to begin by quoting Vincent Van Gogh. According to a literal translation the artist in describing one of his famous paintings said "these peasants are eating their potatoes with those very hands that dug them from the earth' and put them in the dish". Vincent Van Gogh may not have realized at that time, that he could likewise have been describing what is probably one of the oldest of all arts - the art of Material Handling - an art that man with the aid of science has tried to improve since the beginning of time.

Jan 1, 1963

By Thomas N. Walthier

Exploration is the systematically financed and technically oriented search for mineral wealth. Almost all established mining companies have an exploration department. The size of a company's search varies over the years as the company's profits, or the corporate philosophy change. While the established mining companies have exploration departments, they are also alert to acquiring discoveries made by others -- especially by prospectors and small companies without the resources to develop their find. The emphasis in some large companies stresses self-generated discoveries while others rely heavily on acquisitions; again, over the years the emphasis may alternate. In the last analysis, essentially all new mineral wealth was found through someone's exploration effort. Before we discuss how exploration is financed, it will be informative to analyze how discoveries have been made and by whom. Recently, the author conducted a survey of randomly selected major mining companies to answer these questions. Most companies responded and many went to considerable effort to give complete and detailed answers. I thank all for their help and cooperation. The questionnaire is attached as Appendix I. Appendix II is a list of the 400 companies that replied in a complete enough manner and format to be analyzed here. The results of the questionnaire are given in Table 1. Over 57% of the new orebodies acquired by 40 major mining companies during the past quarter of a century were generated

Jan 1, 1977