Search Documents

By Enrique Fernandez

The success of the excavation of a sewage tunnel in a very extreme geological conditions, from river deposits and sandy layers to hard dolomite, and several meters below the estuary under the sea water influence, shows that the choice of a right equipment together with the use of chemical products like foam and polymers enable to dig tunnels in unexpected areas and give solution to the environmental problems. The paper describes the excavation and support process as well as the adopted solutions in every material and during the cross through the intermediate shafts, also under sea influence.

Jan 1, 2003

By G. M. Li

It is shown that seriously preoxidized arsenopyrite can adsorb a large amount of copper ions as unoxidized one, but without, release of corresponding amount of Fe ions; seriously preoxidized pyrite cannot adsorb copper ions, but with release of a large amount of Fe ions. However, if the minerals are rapidly oxidized with potassium permanganate solution, both arsenopyrite and especially pyrite can adsorb a large amount of copper ions, but still without release of corresponding amount, of Fe ions. Cu adsorption (if there is any) on both oxidized arsenopyrite and pyrite is not based on the Cu-Fe exchange mechanism.

Jan 1, 1991

By Bennett D. Lass

A new method for determination of residual flotation oils on beneficiated kaolin clays has been developed. The method, which yields qualitative information, is based on fluorescence measurements employing a spatially resolved, polychromatic illumination source for excitation, and a two-dimensional detection scheme using a silicon-intensified, video imaging device. The method was used to identify residual oils on a beneficiated, Washington County, Georgia, crude clay. The results were compared to a similar qualitative analysis performed via capillary column gas chromatography using an FID detector. The video fluorometry was the preferred method of, analysis.

Jan 1, 1983

By George R. Huebner

The White Pine Copper Company, subsidiary of Copper Range Company, is located in the Upper Peninsula of Michigan. The offices, plant, and mine are six miles south of Lake Superior in Ontonagon County. Employing 1700 people, White Pine is the largest single industry in the Upper Peninsula. 970 underground employees produce 16, 700, tons of ore daily. From this tonnage 363,400 pounds of refined Lake Copper are produced in various shapes as specified by the customer. The following paper explains the geology of the ore body and briefly outlines present mining methods. It enumerates the reasons for considering longwall mining of a hardrock* ore body and the preliminary investigations leading to the decision to undertake the initial test panel. Selection of the initial test panel location is covered in detail. Equipment choice and reasons for that choice are described as well as selection and training of personnel.

Jan 1, 1964

By J. C. Draper

The Duquesne Light Company and GAI Consultants, Inc. conducted a demonstration program aimed at establishing permanent vegetative cover directly on acidic, deep coal mine refuse. Several plots were treated with formulas varying in soil amendment application rates and plant species. Periodic monitoring of refuse chemistry has indicated when maintenance applications of seed and soil amendments were required. To establish drainage control, the site had to be regraded. The most successful formula was applied to the entire site. Specific treatment for acidic spots has been initiated. Results of the program indicate that adequate permanent vegetation has been established.

Jan 1, 1983

By C. Tom Blevins

LADIES AND GENTLEMEN : This presentation is to discuss production and roof control problems associated with directional lateral stresses in an in situ stress field and the approach that Inland Steel Coal Company made in trying to cope with them. Before proceeding, a brief description of the mine location, product, geology, restraints, and mine history is in order.

Jan 1, 1982

By Edgar W. Sawyer

Attapulgite and sepiolite are the clay minerals used to thicken ionically contaminated watzrs in the preparation of drilling fluids. They are nonsweliing clays that can be dispersed and reflocculated by mechanical means to increase the viscosity of fresh water and salt and gypsum contaminated waters. Those gelled in fresh water do not become excessively thick when contaminated with high salt concentrations or polyvalent cations encountered during drilling. Gels formed exhibit thixotropy and yield pseudoplastic rheological behavior due to the particle interactions and mechanical interferences of the flocculated gel structure.

Jan 1, 1983

By G. M. Smith

Several significant past and present producers of high grade and bulk tonnage gold ore from southeastern California and southwestern Arizona can be empirically and genetically linked to regional peraluminous magmatism which occurred during the late Cretaceous and early Tertiary. Geological relationships and geochemical characteristics from the Fortuna Mine area will be described and compared to those of the Tumco Mines area. Each of these historical gold producers is viewed as a morphologic end member in otherwise genetically linked metallogeny. Cold-quartz veins at Fortuna can be directly linked to peraluminous pegmatites both physically and mineralogically. Silica-magnetite±spidote±garnet rock which occurs as relatively barren, discontinuous, foliation- parallel horizons at Fortuna, but as high grade gold ore at Tumco, is interpreted as replacement of calcareous units during the same episode of peraluminous magnatism responsible for the gold vein mineralization. Whole rock and trace element data from pagmatites and aplites of the Fortuna and Tumco areas, together with data from the Gunnery Range batholith of southwestern Arizona, indicate that the magma series (after Keith, 1984) responsible for the gold metallogeny is peraluminous calcic, and is quite rich in sodium.

Jan 1, 1987

By M. Misra

The dispersion of oily collector has significant effect on the flotation recovery of ultrafine coal. Generally, reagent dispersion is accomplished by mechanical mixing and/or ultrasonic agitation, followed by direct addition of dispersed collector into the flotation cell. However, such dispersion and reagent addition techniques are invariably inadequate and non-selective. A new collector utilization technique involving gas phase transport of atomized collector has shown improved results when compared to conventional reagent addition techniques. This new technique involves atomization of the collector into the gas stream. Under these circumstances an aerosol is introduced into the flotation cell. Initially, the oil is dispersed within the gas phase (continuous with respect to oil) and the gas phase is dispersed within the pulp (continuous with respect to aerosol). In the flotation cell, the atomized oil droplets coalesce on the bubble's surface and create a de-facto oil-encapsulated bubble. This approach provides excellent dispersion, increases selectivity, and most significantly increases the flotation rate of ultrafine coal. Furthermore, atomization of collector/frother combinations yielded improved flotation yields and maintained near uniform froth levels which is a desirable feature in coal flotation. In addition to flotation experiments, microscopic examinations of the attachment of oil-coated bubbles at a coal surface were conducted by attachment-time and contact-angle measurements. The oil coated bubbles attach at significantly faster rates and with a higher contact angle than do oil free bubbles.

Jan 1, 1987

By George F. McKeregahan

Phosphate production of the Central Florida Phosphate District has been predominantly from the unique and lucrative Bone Valley Formation, with local and minor amounts coming from the underlying Hawthorn Formation. As the Bone Valley is depleted, replacement production will move progressively into areas of total Hawthorn Production. Significant changes in the characteristics and make-up of the deposit dictate required modifications in mining and beneficiation. Failure to tailor technology to fit the deposits of the future will result in vast "reserve" losses. In the Southern Extension of the Central District - two distinct "ore types" exist. These are presently referred to as the upper (high grade) zone and the lower (low grade) zone. The upper zone is somewhat similar to the Bone Valley Formation and will respond favorably to present beneficiacion practices. The lower zone is strikingly different and its response to conventional beneficiation is not acceptable. The major differences are in grain size distribution and mineralogical make-up of these grains. The Hawthorn differs from the Bone Valley by exhibiting lower grades, lower tonnage yield per acre foot, lower pebble percent of product, higher mining ratios, higher slimes (-150 mesh) content and deeper mining depths. Physical characteristic changes include more frequent occurrences of competent bands or lenses of "limerock" which are submarginal in value.

Jan 1, 1983

By L. Barry Phelps

Selective placement of toxic mine spoil has been advocated as a means of reducing environmental pollution at the source. However, methods of burial to control environmental damage are not well understood. Using the finite element method, this paper investigates the burial of toxic material within low permeability packages below the water table. The effects of differing package and spoil permeabilities, anisotropy, and infiltration are modeled to provide information about their effect on the flow system. Projection can then be made which will assist in the design of the toxic spoil packages to limit the amount of groundwater flowing through them.

Jan 1, 1983

By Frank W. Schmechel

The subsidence monitoring program at the Old Ben No. 24 Mine was planned in 1976 as part of the on- going demonstration of longwall mining. The construction and installation of the network of surface subsidence monuments was started in Play of 1976 and completed four weeks later after which an initial reference survey was made of all surface monuments. Mining of the first longwall panel started in September of 1976 and was completed in May of 1977. Mining of the second panel started in August of 1977 and is continuing at this time. The Automatic Data Acquisition System (ADAS), which is the subject of this paper, was installed over the second panel on March 29, 1978 near the panel center (Figure 1) and approximately 104 meters (370 feet) in front of the face position at that time. Mine No. 24 is located approximately 5 kilometers (3 miles) Northwest of Benton, Franklin County, Illinois. Coal is being mined from the Illinois (Herrin) No. 6 seam which is at a depth of about 189 meters (620 feet) at the site. The Herrin No. 6 is up to 2.7 meters (9 feet) thick in the mine but a constant thickness of 2.1 meters (7 feet) is being mined by the demonstration longwall with both roof and floor coal being left for stability. Although the seam is flat laying at the mine, it dips north- ward regionally. Topographically, the surface over the demonstration panels is essentially flat and low laying with several areas of standing water. The Rend Lake Dam (United States Army Corps of Engineers) is about 305 meters (1000 feet) north of the demonstration site.

Jan 1, 1979

By James R. Yancik

Economical and environmental pressures necessitates the recovery of the minus 0.6 mm x 0 coal generated by todays mining machines. This size fraction, dependent on the type of production unit, maintenance of the production unit, and the Hardgrove Grindability Index, can be a substantial portion of the Preparation Plant feed. Historically, dewatering of the collected 0.6 mm x 0 product has often been rather expensive and marginal with respect to surface moisture reduction. The Freeman United Crown II Preparation Plant more than adequately demonstrates that the continuous scroll type centrifuge can dewater 0.6 mm x 0 coal to acceptable surface moisture levels.

Jan 1, 1981

By S. C. Sun

Very little information is available concerning the magnetic properties of minerals and only recently has there been any attempt to correlate magnetic susceptibility with varying chemical composition1. The work described here covers a study of the relationship and chemical composition of both the rutile and sphene types of titanium minerals. The relationship between the magnetic susceptibility of three selected mineral specimens and the applied field strength is also presented. Experimental: The equipment and procedures used in this in- vestigation for crushing and cleaning the mineral specimens and for determining the magnetic susceptibilities were the same as that employed by Spokes and Mitchell1. The particle size of-the measured specimens was limited to 270/325 mesh.

Jan 1, 1959

By James H. Vignos

An optical instrument designed for the on-line measurement of the size distribution of coarse particles (3-500 mm) being transported on a conveyor belt is described. Included is a discussion of the measurement technique, as well as test data verifying the legitimacy of the basic sensing approach. Field data indicating the instrument's ability to make useful measurements in an industrial environment are also presented. Applications in the mining and mineral industry, for which this instrument was orginally developed, are outlined, with particular emphasis given to the areas of crushing and grinding control.

Jan 1, 1979

By J. E. Moyle

Rio Algom Corporation of Wilmington, Delaware is a wholly owned subsidiary of Atlas Alloys Inc., an Ohio Corporation, which in turn is 100% owned by Rio Algom Mines Limited of Toronto, Canada. Rio Algom is controlled by the Rio Tinto Zinc Corporation of London, England, which has subsidiaries and affiliated operations throughout the world. Rio Algom geologists first became interested in this Utah pro- perty in 1966, after preliminary drilling had indicated that a known orebody close to the surface appeared to continue on the dorm thrust side of a major local fault, known as the Lisbon fault. Accordingly, in 1968, arrangements were made to acquire what was known as the "Humeca Option", a total of 2,573 acres located in San Juan county in south-east Utah, 35 miles south-east of the town of Moab.

Jan 1, 1975

By R. M. Clowes

Lithoprobe is a collaborative, multidisciplinary research project which is providing new insights into the tectonic evolution of the North American continent through its work within ten study areas across Canada. For the mining industry, such results provide a well-constrained regional framework and better understanding of tectonic processes which lead to the development of ore deposits. In mining camps, seismic reflection methods have proven effective in imaging shallow to moderately dipping litho logic contacts as well as structural features, and in some cases have been used for the direct detection of ore bodies. Here, short case histories are provided for the Abitibi greenstone belt (VMS deposits) in Quebec and the Thompson nickel belt in Manitoba.

Jan 1, 1999

By John F. Slonaker

This report is a review of current research being conducted in the United States which is intended to increase the utilization of coal ash. In order that this report be as timely as possible, the majority of information was obtained by direct comunication with the people listed in the references. Due to the magnitude of the flyash research program, some projects may be inadvertently omitted. Field research on flyash for use as an agricultural fertilizer is being monitored at Virginia Polytechnic Institute and State University.1 This research is directed at determining the plant nutrients that are available in flyash as well as the quantities of flyash that can be applied to agricultural soil without adversely affecting plant growth, Coal mine spoil and refuse bank reclamation with power plant flyash is being demonstrated by United States Bureau of Mines, Morgantown, West Virginia.2 Numerous highly visible coal refuse piles and strip mine spoil banks contribute to air, water, and land environmental problems. Revegetation of several experimental sites with flyash from bituminous coal-fired power plants was undertaken in West Virginia and Pennsylvania. Conventional farm equipment was used at some of the sites while large earthmovers were required at others. The flyash served as a neutralizing agent, dilutent, and soil amendment to provide some nutrients which enhanced vegetation of the barren areas, Estimated cost of reclamation by this method is $300.00 per acre of previously leveled area. This figure can vary considerably depending upon the topography of the site, haul distance, quality of the soil and quality of flyash.

Jan 1, 1974

By C. R. Peterson

A cutter vibration monitoring system is described which would map seam strata non-uniformities to permit guidance within the seam. An extremely simple and rugged transducer is used which is compatible with conventional cutters and cutter replacement practices, and believed to be suited to the mining environment. Laboratory tests show that the system can detect bedding planes in otherwise homogeneous material. A data display system which would employ the human operator's natural pattern recognition skill and judgement will be developed, Intended for remote control applications in general, the system is of direct interest for today's continuous excavators in coal or in any other machine excavated bedded deposit.

Jan 1, 1985

By Boris J. Kochanowsky

In the mobile crushing unit system trucks are replaced by a conveyor resulting in a "continuous" almost "fully-automated" operation with all its attendant advantages. In consequence, overall operating costs are greatly reduced. Because of the new designs of large mobile crushing units that have been brought on-to the market, the use of these plants has increased significantly during the last three years. This paper describes the designs of new mobile crushing units, and emphasizes the advantages that such plants offer to the rock products and mining industries. It examines operating costs, and indicates the conditions in which the application of these plants is most profitable.

Jan 1, 1968