Search Documents

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION Shrinkage stope mining can be employed in steeply dipping veins where both the wall and the vein material are sufficiently strong to stand with only minimal ground support. Shrinkage stope mining takes advantage of the swell in volume produced in breaking in-place ore. This expanded volume of ore is allowed to occupy part of the mined-out vein, and in so doing provides ground sup¬port and a working surface for the miners. Only enough of the ore is drawn after each stoping cut to allow work¬ing room. Not until the entire mining block has been broken is the full amount of broken ore drawn from the stope. DEVELOPMENT PRACTICES FOR SHRINKAGE STOPING The vein is developed into stoping blocks, each of which is 76 to 91 m (250 to 300 ft) in length and 61 m (200 ft) between levels. Level development, described later, is either on the vein or parallel to it with crosscuts periodically driven over to the vein. There are usually two exits from each stope. The first entry is a raise at one end driven either conventionally by raise climber, or by a raised borehole. Present practice is that this raise, put in from level to level, is either a 2.1- x 2.1-m (7- x 7-ft) Alimak raise or a 1.2- to 1.8-m (4- to 6-ft) diam borehole. Either raise system will require pro¬visions for an ore chute carried with the stope to the haulage level or the scram drift. At 9- to 12-m (30- to 40-ft) vertical intervals, dogholes are developed from the raise so that when stoping breaks back into these dogholes, timber or steel sets and necessary service facilities can be installed. The second entry to the stope may be either a similar raise at the stope endline, or more economically, a cribbed raise carried with the stope. As previously stated, development of the ore block is achieved by either drifting on the vein or by paralleling the vein with a footwall lateral and then crosscutting over to the vein at specified intervals. In the following discussion, three basic cases are illustrated in Figs. 1, 2, and 3. In Fig. 1, development is in the footwall by a 3- x 3-m (10- x 10-ft) trackless lateral. A heading is also driven on the ore and taken either full width or driven a standard size and slabbed to the vein width. Approxi¬mately 9-m (30-ft) long crosscuts on 7.6-m (25-ft) cen¬ters are driven from the lateral to the vein. For ease in muck handling they are usually put in on a slant rather than at right angles. A single orepass, located off the lateral and in the center of one stope block, can serve not only that stope, but also one on either side, up to a tramming distance of not more than 137 m (450 ft). Raises are put at the stope endlines on 91-m (300-ft) centers. The back of the vein is shot down and just enough broken material is drawn off to permit access for men to work off the broken ore. Development in Fig. 2 progresses by driving a 3- x 3-m (10- x 10-ft) trackless heading on the footwall side of the vein. The ore block is delineated by raises on 91-m (300-ft) centers. Crosscuts are again driven on 7.6-m (25-ft) centers over to the vein. Approximately four rounds are then taken up to the vein and each round is successively belled out so that all the crosscuts (pockets, in this case) connect. In this development, as opposed to that in Fig. 1 where there were no belled

Jan 1, 1982

At present the feasibility of developing underground facilities for the storage of a number of products including toxic waste, oil, nuclear waste and low pressure gas is under investigation in e number of countries. A possible method of storage is in large excavations, Preliminary ventilation design work has identified that the climatic conditions encountered within these large excavations are a limiting ventilation pollutant within the ventilation system. This paper examines the design of a variety of sizes of excavation from a ventilation viewpoint. The main phases of an excavations lifetime can be divided into four main phases, these being construction, civil and mechanical fitting, storage, full and sealed. The paper details ventilation design options for the first two phases of e vaults lifetime, giving climatic simulations to assess the likely climatic conditions within the excavations for e number of facility depths. The options for climatic control are given and analyzed by means of climatic simulations techniques. l. INTRODUCTION The feasibility of developing underground facilities for the storage of a number of products is under investigation at present in a number of countries. This paper details a possible design for such a facility where the product is to be stored in large underground excavations. A facility layout has been designed with the aim of allowing concurrent construction and storage operations. Thus from a ventilation perspective the facility consists of two circuits , a construction ventilation circuit and a product ventilation circuit both of which are served by an intake and a return surface connection The construction and storage circuits are considered as independent of each other , any interaction in the form of leakage must be from the construction to the storage circuit. From the facility design a ventilation network was developed to assess the ventilation requirements of the facility. In analyzing the pollutant loads for the construction circuit two pollutants were recognised to be critical to the ventilation design , these being diesel exhaust fumes and heat end humidity. In this paper ventilation design options for the construction and civil and mechanical fitting phases of the excavations are analyzed by means of climatic simulation and options for climatic control within the vaults are outlined . 2. FACILITY DESIGN A schematic diagram of a facility design is illustrated in Figure 1. There would be two distinct ventilation circuits , one to service the construction operations and the second to serve the storage operations which occur concurrently with construction , the circuits are separated by ventilation bulkheads . Access to the facility for intake air is provided by two drifts, one to serve each circuit. Two shafts act as returns to surface. The facility consists of two distinct zones for the storage of two types of product. One type is to be stored in smell linear excavations. The second zone is for the storage of a second product in larger excavations. The maximum cross-sectional area and perimeter for the smell linear excavations are 456.25 m2 and 83.2 m, while for the larger excavations they are 440.1 m2 and 86.4 m. Excavation construction consists of three phases: 1. Initial pilot tunnel development between main intake and return to provide through flow ventilation. 2. Enlargement to produce the required finished cross-section. 3. Civil and mechanical engineering work to fit out the excavation ready for storage. It is proposed to excavate the excavations using drill and blest methods utilising diesel equipment. Spoil is to be transported to surface by a conveyor belt system. At any one time the maximum number of working places requiring ventilation will consist of ; 3 storage sites, 2 excavations under construction, 2 excavations undergoing civil and mechanical fitting. [ ]

Jan 1, 1993

By Tim O’Neil

Until about three years ago, Asarco's copper business consisted predomi¬nantly of custom smelting of ores and concentrates produced by other mining companies. Since then, the company has been transforming itself into a fully integrated producer in copper mining, smelting, and refining. In doing this, Asarco has lowered its costs and restructured its operations and finances. Now, Asarco hopes to complete this process by spending $260 million over the next three years, to expand and modernize its copper facilities and boost production by some 40%. The capital spending program includes: • $130 million at the Ray mine about 113 km (70 miles) north of Tucson, AZ, to expand mining capacity and install an in-pit ore crusher, mill, and concentrator; • $100 million, to expand the mining capacity at the Mission Complex located south of Tucson, AZ, and refurbish the adjacent, idle Pima mill and concentrator. (Asarco had earlier exercised an option to purchase the Pima mill for about $6 million); and • $30 million, to modernize the copper smelter in El Paso, TX, with a new flash smelting process. The new program is in addition to a recently completed first-phase expansion of the Mission mine, mill, and concentrator. This $13 million debottlenecking of existing operations in¬creased production capacity by 46% or 24.5 kt/a (27,000 stpy), to 79 kt/a (87,000 stpy) of copper in concentrates. In addition, a previously an¬nounced $12 million expansion program at the Ray mine is scheduled for completion in early 1990. It will expand mill capacity, to offset the anticipated effects of increasing ore hardness as the pit deepens. Ray produces 68 kt/a (75,000 stpy) of copper in concen¬trates and an additional 36 kt/a (40,000 stpy) of electrowon copper. By 1992, when Asarco's expanded and modernized copper facilities are operating at capacity, the company's mine output will have increased by 67 kt/a (74,000 stpy), to 263 kt/a (290,000 stpy) of contained copper. That will be enough to provide all of the feed required for Asarco's two copper smelters - by then, both of them modern, state-of-the-art facilities. Asarco's expansion and modernization program will further reduce costs and provide added assurance that the company's copper business will be profitable at the bottom of the cycle, according to Chairman Richard de J. Osborne The Ray mine portion of the new program will include construction at the mine of a new mill and concentrator, with a capacity of 18 kt/d (20,000 stpd) of ore. These new semiautogenous grinding mills and large capacity flotation cells will augment the present 27.2 kt/d (30,000 stpd) concentrator located 29 km (18 miles) away, in Hayden, AZ. A 29 km (18 mile) pipeline will be built to carry tailings in slurry form from the new Ray mill to the present tailings pond. Concentrates from the new facility will be shipped by rail to Asarco's Hayden copper smelter. Ray's present 27.2 kt/d (30,000 stpd) crusher, adjacent to the open-pit, will be replaced by a 54.4 kt/d (60,000 stpd), portable in-pit crusher and conveying system. This will reduce the more expensive ore haulage by truck. The Ray project is scheduled for completion by 1992. It will increase the mine's annual output of copper in concentrates by an additional 33.5 kt/a (37,000 st), to 102 kt (112,000 st). And the project could mean an additional 400 jobs at the 730 employee Ray operation. Work at the Mission Complex involves reactivation of the Pima mill and concentrator and expansion of mine output sufficient to provide ore to both the Pima mill and the present Mission mill. In 1985, Asarco purchased the Pima mine, which occupies one end of the Mission pit. The work at Mission will increase its annual capacity by 33.5 kt (37,000 st), to 112 kt/a (124,000 st) of contained

Jan 1, 1989

By David A. Lindsey

In this paper, we present a physiographic classification of gravel deposits, identify some field measures of aggregate quality, and describe sampling strategies for mapping aggregate quality in the Front Range Urban Corridor of Colorado. Gravel occurs in four types of deposits along the Front Range of Colorado: (1) piedmont alluvial fans, (2) high dissected terraces, (3) high (continuous) terraces, and (4) floodplains and low terraces. The four deposit types are the basis for definition of gravel-deposit models, which differ in geologic environment, deposit characteristics, deposit size, environmental impacts of mining, and post-mining use. Of the four types, floodplains and low-terrace deposits have been exploited most for gravel. High terraces also have been mined. Deposits of high dissected terraces and dissected alluvial fans have produced minor amounts of gravel, mostly for use as local fill. Studies to identify useful field measures of aggregate quality and to determine the appropriate scale for sampling were conducted on gravel deposits beneath the flood-plain and low terraces of the South Platte River north of Denver and the Cache la Poudre River between Ft. Collins and Greeley. Gravel deposits of the South Platte were selected for study because they represent the last major resource of gravel for aggregate in the Denver metropolitan area. The Cache la Poudre valley is the primary source of gravel aggregate for rapidly urbanizing areas around Ft. Collins and Greeley. Of all the field measures of gravel quality, the most important is particle size. Various parameters that measure particle size were investigated, but the easiest to determine, and the most useful to the aggregate industry, are measures of the proportion of coarse sizes. Particle size varies widely in gravels of the urban corridor. Gravel lithology, particularly the presence of deleterious particles such as reactive volcanic rocks and decomposed rocks, must be determined to assess aggregate quality. Studies of South Platte and Cache la Poudre gravels have not revealed large proportions of deleterious lithologies. Studies of particle shape revealed only small numbers of physically weak shapes in both the South Platte and Cache la Poudre gravels. Particle shape does not appear to vary from place to place in the gravels. Rounding, or the ab¬sence of angular corners, may play a role in the tendency of loose gravel to yield under load. South Platte and Cache la Poudre gravels are rounded, and rounding tends to increase upstream. Before the quality of gravel in a valley can be assessed, the stratigraphy of the gravel must be known because it affects sample design. If only a single gravel layer is to be studied, only the thickness of the gravel must be known before sampling. If, however, more than one layer of gravel-distinguished by particle size, sorting, or lithology-is present, sampling must take into account the thickness and distribution of each layer. For example, three gravel layers of different particle size underlie the floodplain and low terraces of the South Platte. The tributary Cache la Poudre, on the other hand, contains gravel layers that can be distinguished only locally and vary slightly in particle size. Sampling experiments were conducted on gravel bars in the South Platte River and in gravel pits on the floodplain and low terraces of the South Platte and Cache la Poudre Rivers. Experimental results indicate that, even where sample error is large, regional and stratigraphic variation may be measured if it is large relative to sample error. Using vertical trench samples weighing an average of 40-90 pounds, down-stream decrease in coarse particle size was mapped for Cache la Poudre gravel, and differences among superposed gravel beds were measured for South Platte gravel.

Jan 1, 1999

Disposal of solid and liquid wastes from mining and milling operations has become a focus of attention in recent years. Consequently, the geotechnical engineer is more frequently associated with design of disposal facilities. Jack Wulff, a representative of one consulting firm with experience in this field, talks with ME about the geotechnical engineer's contribution. Mr. Wulff, mine and mill waste disposal today is receiving more attention-and many more dollars-than in the past. Regulatory agencies have promulgated demanding requirements concerning mill waste (especially uranium mill waste) and specialist consultants are frequently being called in to design disposal systems. What can the experienced geotechnical engineer add to the development of waste disposal facilities? It's true that geotechnical engineers have recently become more visible in the minerals sector, but we've been around mining for a long time-as foundation engineers for mills and mine support buildings, and for geotechnical aspects of open pits, pipelines, railroads, roads, and so forth. We've also designed water supply dams, which could be considered recursors of tailings dams and other forms of disposal systems. Let me show by example what geotechnical engineering can contribute to waste disposal facility design. I recently was asked to look at several small wastewater impoundments which had failed. The design of the earth embankments appeared, at first glance, to be rather conservative. They were only about 3.4 m high, the slopes were 3 to 1 (horizontal to vertical), with about 24 m of bottom contact with the earth foundation. But there had been three episodes of dike failure in a few months, all upon initial filling. The problem was the nature of some material in the foundation that was also used as structural fill-a dispersive clay that readily deflocculated and eroded on contact with water, especially with seeping or flowing water. The design did not include the defensive measures required to use such materials confidently in water retention structures. Apparently, the designer did not recognize the potential problem posed by the unusual soil characteristics. That's the sort of engineering information fundamental to geotechnical engineering, but not necessarily a part of the civil, structural, or mining engineer's professional training or experience. This difference in expertise is not simply a matter of factual knowledge-it also affects the design process. The structural engineer can design a structure to fit the client's functional needs and can specify the materials (grade of steel, PVC, concrete, etc.) to meet the demands of the design. The geotechnical engineer's design process is somewhat different, since we work with natural materials, not man-made materials produced according to specification. We first have to establish what kinds of materials are available (usually directly from the chosen site, since importation of materials becomes expensive). Then we determine the engineering properties and characteristics and, finally, design the structure to fulfill the client's requirements within parameters dictated by available materials. In brief, the geotechnical engineer works with naturally-evolved, not man-made, materials and uses design techniques developed to accommodate that fact. Because no two sites are exactly alike in configuration, structural (geologic) characteristics, or available materials, there will be unique design and judgmental questions to be resolved on virtually every project. You said that water retention dams could be considered the precursors of tailings dams-you probably had a specific technical relationship in mind. There's a very strong carryover of methodology from earth dam design, where the technology developed and where it has become very refined. In designing a tailings impoundment or similar facility, essentially the same procedures of field sampling are involved (with a geotechnical engineer or an engineering geologist directing the program since representative

Jan 7, 1980

By E. Steel, V. S. Znamensky, A. Wylie

The asbestiform habit is most commonly developed in certain amphiboles and chrysotile, but other minerals also may crystallize with this unusual habit. The habit may be characterized by (1) a fibril structure, single or twinned crystals of very small widths (generally less than 0.5 pm), which have grown with a common fiber axis direction, but are disoriented in the other crystallographic directions; (2) anomalous optical properties, primarily parallel extinction; (3) unusual tensile strength; (4) high aspect ratio; and (51 flexibility. In addition, there is evidence to indicate that some amphibole asbestos may have unusual surface properties. ASBESTOS AND THE ASBESTIFORM HABIT Asbestos is defined as a group of highly fibrous silicate minerals that readily separate into long, thin, strong fibers of sufficient flexibility to be woven, are heat resistant and chemically inert, and possess a high electric insulation, and therefore are suitable for uses where in- combustible, nonconducting, or chemically resistant material is required (Gary, et al., 1974). The most common minerals that may occur with the asbestiform habit are chrysotile, grunerite (amosite], riebeckite (crocidolite), actinolite, anthophyllite, and tremolite; although the development of this habit among these minerals is rare. Other minerals, most notably other amphiboles, can occur in this habit, but no others have been mined commercially as asbestos. All asbestos is confined to metamorphic rocks, even though other habits of the amphiboles are common in igneous rocks. Slip fiber veins are the most common deposits (South African amosite, Canadian chrysotile, etc.), but mass fiber deposits also may occur such as California chrysotile or mountain leather. Field relations and experimental data support the hypothesis that metasomatism is the dominant process in the formation of asbestos fibers, amphibole as well as serpentine. The crystal habit of a mineral is the shape or form a crystal or aggregate of crystals take on during crystallization. The asbestiform habit has a number of characteristics that differentiate it from other habits. Chief among these is the fibril structure.Afibri1 is a single or twinned crystal with a very small width, generally less than 0.5 pm, and an extremely high aspect ratio; bundles of fibrils may have lengths reaching into the cm. Fibrils share a common crystal growth direction along the long axis of the fiber, but appear to be disoriented with respect to one another in the other crystallographic directions. The structure of the individual fibrils, and the organization of fibrils within a fiber may differ among the various types of asbestos. The fibril structure of asbestos is probably a factor in controlling a number of secondary properties that include high tensile strength, flexibility sufficient for weaving, and anomalous optical properties. The high tensile strength of asbestos is quite remarkable, exceeding that of the ordinary varieties by a thousand fold (Zoltai, 1978). In part, this may be attributed to the lack of defect on the fibril surfaces (Zoltai, 19781, but some contribution also must come from the existance of bundles and the nature of the ordering of and forces among the fibrils. The flexibility is not only enhanced by the fact that the fibrils may slip past one another, but by their small widths and extreme aspect ratios. However, structural defects parallel to the fiber axis also may contribute to this property. Among the common commercial asbestos types, the greatest flexibility is found in chrysotile and the least in grunerite asbestos (amosite), varying inversely with fibril thick- ness. In addition, at least for chrysotile, composition also may affect the flexibility of the fibers. Finally, most asbestos minerals are mono- clinic, but optically display parallel extinction (Heinrich, 1965, and Wylie, 1978). This also must be due, in part, to the ordering or lack of ordering of the fibrils. The fibril structure is probably a random

Jan 1, 1986

By John H. Bassarear

How best to grind? This article compares conventional crushing and grinding circuits to semiautogenous circuits, reviews recent installations of each circuit, and describes seven methods of using autogenous or semiautogenous techniques. In addition, steel and power consumption data are reported and benefits of a dedicated digital computer are discussed. Size reduction is the most expensive operation in most mills. Crushing and grinding are usually the greatest part of capital costs. They often make up 60-70% of total mill operating costs. Picking the proper crushing and grinding method must, therefore, be done with great care, so the best circuit is chosen. In the past 10 years, there has been a strong trend toward using autogenous or semiautogenous grinding in mills throughout the world. Autogenous grinding is favored when the ore is quite competent and a fine grind is needed. Semiautogenous grinding is applied when fine crushing could cause severe problems or when ore varies in hardness or competency. The taconite iron ores of northern Minnesota fit the description for an autogenously ground ore and many are successfully ground that way. Most im¬pressive are the nine lines of 11 x 4.9 m (36 x 16 ft) mills powered by 9 MW (12,000 hp) motors at Hibbing Taconite. Porphyry copper and molybdenum ores fit the description for semiautogenous grinding. Recent installations include Highmont in British Columbia, Canada, and Quintana in New Mexico. Sampling Many mills have been built based on inadequate sampling data or insufficient tests. With the cost of many mills exceeding several hundred million dollars, it is mandatory that geologists, mining engineers, and metallurgists work together to prepare representative testing samples. Simple, repeatable work index tests are usually sufficient for rod and ball mill tests. However, pilot plant tests on 50-100 t (55-110 tons) of ore are frequently necessary for autogenous or semiautogenous mills. Preparation and selection of the test sample is of utmost importance. Procedures for autogenous and semiautogenous mill pilot plant tests are relatively simple for those experienced in running them. Reliable and repeatable results can be obtained if simple, fundamental procedures are followed. The accompanying figure shows a typical conventional crushing-grinding circuit with three stages of crushing followed by ball mills or a rod mill-ball mill combination. This flowsheet is typical of many mills that have been built throughout the world. Also shown is a typical semiautogenous (SAG) circuit with feed coming directly from a primary crusher, and the semiautogenous mill product going to the separation process. Many similar semiautogenous circuits are built today because they are simple and flexible, lend themselves readily to high tonnages, and usually cost less to build and operate. With some ores, it is possible to send mine-run ore directly to the semiautogenous mill, eliminating the need for a primary crusher, as at Benquet's Dizon mill in the Philippines. An autogenous or semiautogenous circuit, as the name implies, uses the ore itself to assist in the grinding process. Generally, for this type of circuit, the ore must be competent so large ore chunks can be used to grind smaller ones. If ore alone is used, then the circuit is autogenous; but if balls are added to supplement the charge, then the circuit is termed semiautogenous. Ore competency is not always a criterion, to break up large pieces and wash away cementing material. Autogenous and semiautogenous mills have been very successful on relatively soft uranium ores where the values are frequently found in the material that cements together the sandstone grains. Autogenous Circuits When an ore is hard and competent, it is always possible it might make good "pebbles" that could be used for fine grinding media. Seven methods have been tried using combinations of autoge-

Jan 6, 1982

By D. Nilsson, B. Aaro

To find out if there are any potential savings in "in-the-wall haulage for open pits," the Swedish companies ASEA and Kiruna-Truck in 1984 gave us financial support to study this solution in more detail. In the study, the use of in-the-wall haulage was studied for three hypothetical open pits with different sizes and shapes. Annual ore production rates also varied. A part of this thorough study was published by the Swedish Mining Research Foundation (see Report F 8444, "The Use of Electric Trucks and In-the-Wall Haulage in Open-Pit Mining," in Swedish with an English Summary). Although in-the-wall haulage is of interest in some open pits, the local terrain is important for profitability. The authors do not think in-the-wall haulage is of any major interest for the mining industry. The following is a summary of some of the author's findings. To place the haul road in the wall is not of interest in open pits with declining metal contents in the bedrock. In such mines, the volumes from the haul roads will not yield revenues. The cost per m3 for an underground haul road is much higher than for a haul road in the pit. This means that it is only of interest to place the haul road in the wall when mining gets deeper than about 50 m (165 ft). In-the-wall haul roads will reduce flexibility in the pit, and it will make necessary the use of smaller equipment with lower productivity and higher costs per ton. As Hustrulid, et al. show (Table 4), excavation savings of material hauled are very low, $0.10 to $0.25/t (0.09 to 0.27 per st). The extra operating cost, due to lower productive equipment, will normally be much higher and thus destroy the whole idea with in-the-wall haulage. If electric trucks are profitable for in-the-wall haulage, it is normally also profitable to use electric trolley assist for trucks on the haul road in the pit. But the profitability of using electric power is different in different countries, and depends on the relation between the cost for electric power and diesel fuel. In the US, diesel fuel is inexpensive compared with electricity, but in a country like Sweden, diesel fuel is much more expensive. In most open pits, the trucks have to move a considerable distange from the loader until they reach a final haul road in the wall. A trolley line along such temporary haul roads will be exposed to flyrock. It is normally less expensive to perform rock support from the open pit than from underground ramps in the wall. In Fig. 8, Hustrulid et al. gives the impression that the underground haul roads will be very close to each other. This is seldom the case. Figure 1 shows a haul road in the wall. The haul road passes through each cross-section only once. Arranging a reliable dewatering and rock support system from only one underground ramp is probably impossible. Many more drifts are therefore necessary. In our report, we also studied what would happen if the final pit slope is increased by 5°, using underground drifts in the wall. Our conclusion was that, the extra cost for drifts, rock support, pumps, etc. destroys the whole idea, and that it was better to accept a higher stripping ratio with the haul road in the pit and to use conventional low-cost open pit equipment. Finally, we think it is would be difficult to try to reduce the safety factor when determining the slope angle by moving the haul road in the wall. Minimizing the risk for pit wall collapse is also important with in-the-wall haulage, primarily because men and equipment will be working in the pit, but also to guarantee many accesses between the pit and the haul road in the wall.

Jan 1, 1990

By D. Nilsson, B. Aaro

To find out if there are any potential savings in "in-the-wall haulage for open pits," the Swedish companies ASEA and Kiruna-Truck in 1984 gave us financial support to study this solution in more detail. In the study, the use of in-the-wall haulage was studied for three hypothetical open pits with different sizes and shapes. Annual ore production rates also varied. A part of this thor¬ough study was published by the Swedish Mining Research Foundation (see Report F 8444, "The Use of Electric Trucks and In-the-Wall Haulage in Open-Pit Mining," in Swedish with an English Summary). Although in-the-wall haulage is of interest in some open pits, the local terrain is important for profitability. The authors do not think in-the-wall haulage is of any major interest for the mining industry. The following is a summary of some of the author's findings. To place the haul road in the wall is not of interest in open pits with declining metal contents in the bedrock. In such mines, the volumes from the haul roads will not yield reve¬nues. The cost per m3 for an underground haul road is much higher than for a haul road in the pit. This means that it is only of interest to place the haul road in the wall when mining gets deeper than about 50 m (165 ft). In-the-wall haul roads will reduce flexibility in the pit, and it will make necessary the use of smaller equipment with lower productivity and higher costs per ton. As Hustrulid, et al. show (Table 4), excavation savings of material hauled are very low, $0.10 to $0.25/t (0.09 to 0.27 per st). The extra operating cost, due to lower productive equip¬ment, will normally be much higher and thus destroy the whole idea with in-the-wall haulage. If electric trucks are profitable for in-the-wall haulage, it is normally also profitable to use electric trolley assist for trucks on the haul road in the pit. But the profitability of using electric power is different in different countries, and depends on the relation between the cost for electric power and diesel fuel. In the US, diesel fuel is inexpensive compared with electricity, but in a country like Sweden, diesel fuel is much more expensive. In most open pits, the trucks have to move a considerable distange from the loader until they reach a final haul road in the wall. A trolley line along such temporary haul roads will be exposed to flyrock. It is normally less expensive to perform rock support from the open pit than from underground ramps in the wall. In Fig. 8, Hustrulid et al. gives the impression that the underground haul roads will be very close to each other. This is seldom the case. Figure 1 shows a haul road in the wall. The haul road passes through each cross-section only once. Ar¬ranging a reliable dewatering and rock support system from only one underground ramp is probably impossible. Many more drifts are therefore necessary. In our report, we also studied what would happen if the final pit slope is increased by 5°, using underground drifts in the wall. Our conclusion was that the extra cost for drifts, rock support, pumps, etc. destroys the whole idea, and that it was better to accept a higher stripping ratio with the haul road in the pit and to use conventional low-cost open pit equipment. Finally, we think it is would be difficult to try to reduce the safety factor when determining the slope angle by moving the haul road in the wall. Minimizing the risk for pit wall collapse is also important with in-the-wall haulage, primarily because men and equipment will be working in the pit, but also to guarantee many accesses between the pit and the haul road in the wall.

Jan 1, 1989

By Jeroen van Eldert, Daniel Johansson, Henrik Ittner, Håkan Schunnesson

"Numerous aspects of underground construction, from structural stability to construction costs, depended on the tunnel quality, including blast damage and the Excavation Damage Zone. Accurately quantifying the extent and severity of damaged rock is a problem. Recent technical developments in the field of Measurement While Drilling (MWD), including software for on-board logging and on-site analysis, have shown potential for rock-mass characterization. Ground Penetrating Radar (GPR) and P-wave velocity measurement have also improved and show similar potential. This paper explores the use of MWD, GPR and P-wave velocity measurements and uses them in techniques for excavation damage characterization and prediction. The paper is based on data collected from a small underground waste-collection site in central Stockholm, Sweden. The data is correlated against rock-mass characteristics and their responses are evaluated. Results indicate potential for excavation damage characterization for all tested techniques, which could minimize blasting damage and improve the over-all tunnel quality. 1 INTRODUCTION During underground excavation the rock mass is influenced in many ways. The Excavation Damage Zone (EDZ) is a result of these influences. The EDZ can be defined by an irreversible change in rock mass properties, for example increased permeability. EDZ is influenced by the excavation method, the rock mass properties and the in-situ stresses in the area of the tunneling. Since the 1990s research has been done on the EDZ by Emsley et al. (1997), Christiansson et al. (2005), Olsson et al. (2009), Ouchterlony et al. (2009), Ittner et al. (2014), and Siren et al. (2015). Based on past literature the EDZ have in this paper been separated in the following subzones: 1. Failure Zone or over-break is the area outside the planned tunnel profile, including the Look-Out and hole deviation. This zone consists of fracture networks (both natural and blasting-induced), that caused rock fall-outs. The extent of the over-break can be determined by volumetric scanning and photogrammetry and the half cast factor can be used as a damage indicator. 2. The Damaged Zone is split into three parts and but the quantity and depth of damage is difficult to measure. Although it can be visualized by sawing of rock slices in the tunnel wall (Olsson et al. 2009), diamond coring (DC) or P-wave velocity reduction (Jern 2001): a. Inner Damage Zone (Crush Zone): It is located directly around the drill hole, and is caused by the shock-wave energy of the detonation. The micro fractures in the Crush Zone produce a white-wash (rock dust) in the half cast. b. Transition Zone: This zone consists of micro fractures that connect and form macro fractures, both radially and parallel to the tunnel wall. The macro fractures are caused by the gas expansion during the detonation of the explosive; it increases the pressure in the (micro) fractures and creates the macro fractures. Seismic reflection, rock slicing and core drilling can be used for the examination. c. Progressing Zone: In this zone the existing radial fractures propagate due to the increase gas pressure inside these macro fractures. Examination methods are seismic reflection, rock slicing and core drilling. In addition, the Peak Particle Velocity (vibrations) could be used to estimate the depth (Tesarik et al. 2011)."

Jan 1, 2016

By R. Kneisley, D. Conover, K. Haramy, K. Hanna

INTRODUCTION Coal mine entry intersections are high-risk areas for roof falls due to inherently wide roof spans, excessive stress, and variable intersection shapes resulting from breakthrough misalignments. Statistics from underground coal mines reveal that a high percentage of injuries occurs from roof and rib falls in entry intersections (Peng, 1980). The U.S. Department of the Interior, Bureau of Mines, is conducting a field research project to investigate failure modes surrounding underground coal mine entry intersections. The research objectives are to (1) develop a method to determine failure modes and stress-displacement relations around coal mine intersections and (2) develop engineering guidelines and empirical relationships for use in designing safer coal mine entry intersections. The basic approach to achieve the objectives is to instrument and monitor intersections before, during, and after intersection development in order to determine contributing parameters, such as in situ stresses, stress changes, strata movement, geology, physical properties, and mining sequence, that may influence the short- and long-term stability of the intersection and adjacent entries. This paper describes a rock mechanics instrumentation program, data analyses, and a comparison of two case studies conducted at two underground mines, designated as "A" and "B", in the Illinois Coal Basin. The instrumentation plans and data collected during development and long-term monitoring of four-way intersections and adjoining entries are presented. Data analyses of pre- and post-mining roof stress, pillar loading, strata movement, roof bolt loading, and geologic features are included. INTERSECTION FAILURE MECHANISM The region surrounding an entry intersection is characterized by different failure criteria than the region surrounding a single entry. Stresses induced during intersection development may result in a high incidence of roof and rib failures. Various numerical modeling techniques have been used to evaluate the failure modes surrounding intersections (Gercek, 1982; Chugh et al., 1975). Numerical modeling techniques include problems associated with the analysis of post-failure behavior, provision for different horizontal stresses (i.e., 01 f 021, and determination of inputs required for any non-elastic behavior. It seems likely that more sophisticated failure criteria, based on actual field data, are needed. The Bureau of Mines has conducted an extensive instrumentation program to investigate actual intersection failure mechanisms and to provide an improved understanding of stresses and deflections using beam and plate theories. Beam theory is not applicable to analyzing intersections (Wright et al., 1964); however, it can be used to explain roof deflection and failure (shear and flexure) of adjacent entries and to provide an improved understanding of stress changes and displacements as the entries, crosscuts, and intersection are developed (Hanna et al., 1985). Beam theory may be used for entries when the roof length is twice the width. When the length is less than twice the width (as in intersections), the roof must be analyzed as a three-dimensional problem, and stress and deflection calculations are based on flat plate theory (Adler and Sun, 1976). The confined-core theory (Wilson, 1972) hypothesizes that within a typical pillar, two regions exist: a confined-core region where the horizontal confining pressure is uniform and approximately equal to the overburden pressure, and a yield zone where the vertical pressure increases from nearly zero at the rib to a pressure peak at the boundary of the yield zone. The strength of coal in the yield zone ranges from nearly zero at the rib to nearly full strength at the confined core. The vertical stress in the confined core decreases from maximum at the yield zone boundary to the overburden pressure some distance into the pillar. Excavation of the adjoining entries

Jan 1, 1986

By Spencer R. Titley

The subject of this lecture, a late century perspective on porphyry copper geology, is one of current interest and importance as the search for these ores remains intense. It is presented in the belief that an appreciation of our present understanding of the subject requires it to be viewed historically, thus providing a basis for evaluating appropriate directions for con¬tinued study. At the outset, it is important to note that the technology of mining and extractive metallurgy has developed ore from these low grade orebodies, starting with D. C. Jackling, and has continued to create them as copper grade and price have diminished. But the continued search for them is a geological problem that responds to growing expectations of people and societies; exploration based upon ever increasing knowledge of the habits of the ores has been very successful. This is the story of evolution of geological thought and practice in porphyry ore search across an interval of time beginning with the bulk mining of "low grade copper ores at Bingham and ending with late Century concepts. "How did we get here?" The lecture concerns the ideas of many different people. The ideas and events discussed reflect a bias on North American thought, where the great low grade orebodies were first recognized as such and where many of the basic geological ideas were developed. A very great number of geologists have contributed to this understanding. In no sense is it meant to minimize the contributions to the story that have evolved in the study and mining of ores of the Andes, whose development and expansion has been nearly synchronous with that in North America - nor to minimized comparable contributions made in the late century from studies of the newer discoveries of deposits in other regions, especially the southwestern Pacific regions. In expansion of this topic, I have found that many important concepts are marked by appropriate publication but some are not, or I have not been able to discover documentation. Many notions appear to have become conventional knowledge without publication, mostly being geological viewpoints developed synchronously from similar observation. Thus, apologies are extended in advance to those whose work I have might have missed and to those unknown to me whose unpublished ideas may have seeped into the pool of common knowledge without appropriate recognition. . The analysis here addresses events of two time segments, an older one extending from the developments at Bingham in the early 1900s through the Second World War, ending about 1950; the second period extends from that time to the present. This separation is seen in Figure 1, which traces numbers of publications through the period as extracted from some 700 publications, again with a North American bias, from an annotated bibliography of porphyry copper geology in preparation. During the early period, exploration was "immature" in North America, that is, geologists looked for new districts and sites of the deposits. Outcrops were sought that carried the signatures of former mineralization and regional controls related to structural geology were closely studied. In the later period, North American exploration had "matured" into a study of districts, rather than a search for them. As the studies of these ores intensified during the younger period concommitant with increasing demands for the metal, they did so with a broadened understanding of some habits of occurrence, of hydrothermal alteration, mineral zoning, petrology, and geochemical and geophysical signatures. Outside of North America, search remained "immature" but closely related to the

Jan 1, 1997

By Klimpel. R. R.

Acknowledgments I am honored to be named as a recipient of the Antoine M. Gaudin Award, and I would like to briefly single out four groups who deserve a special thank-you relative to this award. The first group consists of Professor Kawatra, the many international support references that he gathered and the Gaudin Committee itself. I know such things don't come without considerable effort by many individuals, and I'm grateful for their support. The second group consists of the management of The Dow Chemical Company, the managements of various mining companies and, in recent years, the management of G. S. Technologies, all of whom supported me, financially and otherwise, in my grinding, flotation and other particle-processing work. Operations people are the most overworked and under recognized people in the world, whether they be in the mining or chemical industry. Obviously, without extensive industrial support, especially from operating personnel in the mining industry, almost nothing about the work contained in this lecture would have, or could have, happened. The third group consists of a number of coworkers who have played key roles in specifically implementing the new flotation-product portion of this lecture. Of these, Bob Hansen, Don Leonard, Basil Fee, Simon Isherwood, Fernando Cones and Marty Meulendyke deserve special recognition. They have not only been dedicated, but they have been great to work with. Also in this third group are many members of the international academic community, especially those at Penn State. Professor Leonard Austin must be singled out because he took me as a young mathematically oriented chemist and taught me to be an effective process-oriented engineer. Without this experience, I would not have had the over 30-year career as an engineer, which I have loved. In addition, Len planted the size-reduction-research virus in my blood, which I can't seem to get rid of. I also need to mention Professor Frank Aplan, whose obvious love of mineral processing and froth flotation helped to create my interest in flotation. Thus, for those of you who don't like my approach to flotation, it's all Frank's fault. The fourth, and certainly not the least, group to thank is my wife, Charlene, and our two sons, Richard and Steven. No one could have a more supportive family. In every sense of the word, my wife has been my partner from the beginningwe were married at the end of my freshman year in college. She has sacrificed much for me, and I will never really be able to express the depth of my gratitude for Charlene's encouragement, loyalty and support over the past 36 years. General comments on froth flotation The industrial process of froth flotation: Where is it going? I'm here to tell you loud and clear that froth flotation is alive, well, and growing. The inherent characteristics of high mineral throughput per unit of capital, low operating cost per unit of feed, high mineral specificity and high operating flexibility have guaranteed froth flotation an important past and a growing future. As with any evolving technology, there are always trends at the industrial level that are primarily driven by economics. The current trends include: •the movement towards larger and larger equipment, •more alternative equipment designs (e.g., the column cell),

Jan 1, 1996

By E. P. Chen

This investigation involves the development of a two-dimensional continuum model for the description of jointed media. Specific application of the model developed here is for the potential geological disposal of radioactive waste in the layered sequence of fractured volcanic tuffs under Yucca Mountain, Nevada. This is currently being considered by the Nevada Nuclear Waste Storage Investigations Project, administered by the Nevada Operations Office of the U. S. Department of Energy. The work is a direct extension of the previous constitutive model by Thomas (1982) based on the work of Morland (1974). The main feature of Thomas's model includes two parts: a continuum approximation based on average discontinuous displacements across jointing planes within a representative elementary volume, and a material constitutive description based on linear elastic matrix material behavior and nonlinear normal and shear joint behavior between jointing planes. The mathematical descriptions by Morland based on strain partitioning among matrix material and joint sets allow multiple joint sets to be included in the model. However, the initial effort by Thomas to implement Morland's mathematical model included only a single set of joints. To make the material model reflect more realistically the field characteristics, the current work extended Thomas's model to include orthogonal sets of joints. The nonlinear elastic normal joint behavior is retained in the present model. Joint shear response was treated as linear elastic in the shear stress versus shear displacement relationship prior to attaining the stress level governed by the Coulomb friction criterion. Beyond this critical stress value, a horizontal line is assumed in the work of Thomas for the shear stress versus slip displacement relationship such that the shear stress remains constant while the slip displacement increases. Motivated by experimental observation, the current work generalized the shear response to allow a line with finite slope to govern the slip behavior beyond the critical stress level. The inclusion of an orthogonal joint set led to a fourth order algebraic equation for the calculation of stress increments as compared with a second order equation obtained by Thomas. The nonlinear elastic normal joint behavior provides criteria which allow the selection of the root that yields result consistent with the loading condition of the problem. The addition of one more set of joints provides the potential to more completely study the interaction of various parameters representing the characteristics of jointed media behavior. Material responses to various loading conditions based on the present constitutive model have been obtained. These results and their comparisons to single joint set results are presented. Formulation of the Continuum Model The inclusion of an orthogonal joint set led to a fourth order algebraic equation for the calculation of stress increments as compared with a second order equation obtained by Thomas. The nonlinear elastic normal joint behavior provides criteria which allow the selection of the root that yields result consistent with the loading condition of the problem. The addition of one more set of joints provides the potential to more completely study the interaction of various parameters representing the characteristics of jointed media behavior. Material responses to various loading conditions based on the present constitutive model have been obtained. These results and their comparisons to single joint set results are presented. Let us focus our attention on the set with normal n first. Let the jump dilation displacement and jump slip dasplacement associated with the [ ]

Jan 1, 1986

By Lynton B. Manssen

Introduction Net Present Value (NPV) techniques are becoming widely used in industry as a standard analytical tool in making capital budgeting decisions. However, NPV techniques are often misused in "common practice." A comparison was made between the use of NPV techniques in common practice and an Adjusted Net Present Value (ANPV) approach to capital budgeting in the financial analysis of a mining project. The comparison was made by applying both methods to a hypothetical copper project. The intent of the analysis is to provide an example for practitioners to follow when financially analyzing mining (or other) projects. To maintain the thrust of the analysis, the project has been evaluated as a stand alone, total project. No consideration has been made of the division of cash flows accruing to various owners over the life of the project. This omission will not affect the comparative nature of the analysis. This discussion assumes that the reader is familiar with present value as a concept and as a tool in capital budgeting. Finance theory has embraced NPV analysis as the correct way to evaluate capital budgeting alternatives. Many articles have been written expounding the virtues of NPV over other capital budgeting methods, such as Internal Rate of Return (IRR), Payback, Accounting Rate of Return, and others. It is not the purpose of this article to review all of the literature in this area; suffice it to say that in academic circles NPV concepts are accepted as the norm. A survey by Schall, Sundem, and Geijsbeck (1978) indicates that major US companies are finally following in academia's footsteps. Fifty-six percent of the companies responding to the survey use NPV techniques in their capital budgeting process. Further, some 86% of the companies surveyed use discounted cash flow methods (NPV or IRR) for capital budgeting decisions. This compares with a survey by Klammer (1972) that showed 57% of companies using both techniques, a considerable increase in seven years. With the increasing use of NPV techniques in industry, there are certain uses in common practice that can give misleading results. Five common errors in NPV analysis of large projects are: • No distinction is made between real and nominal cashflows. • The discount rate(s) used in the NPV analysis is not formally adjusted for risk. • There is no distinction of possible differences in the riskiness of different project cash flows; i.e., revenue vs. depreciation. • There is no recognition of the cash benefits to the project from interest tax shields (interest payments on the project's debt that are tax deductible). • There is no clear recognition of subsidies to the project from concessionary debt financing. No Distinction Between Real and Nominal Cash Flows Often, expected cash flows for a project are stated as a mixture of real (in constant dollars) and nominal (in current dollars) cash flows. For example, expected revenue cash flows may be stated in real terms and depreciation may be stated in nominal terms. If cash flows are added together to give an after tax cash flow, and this single cash stream is discounted, care must be taken to ensure that cash flows are consistently stated. All cash flows should either be stated in nominal terms or in real terms. In addition, the discount rate used must be stated in the same terms as the cash flows being discounted. Real cash flows must be discounted using real discount rates and nominal cash flows using nominal discount rates. Discount Rate Not Adjusted Numerous methods for obtaining discount rates are used in common practice. Schall and others

Jan 6, 1983

By Wallace W. Roepke, Richard C. Olson

To adequately attack the longwall dust problem, the US Bureau of Mines funded a contract to define dust sources on a longwall mine face area. The study examined the shearer during sumping, cutting, and tramming, the conveyor, and the roof supports. Tests showed the shearer to be the major dust source. Introduction Long-term illnesses place a heavy burden on miners, the mining industry, and taxpayers. Black lung payments to more than 400,000 miners and their survivors exceeded $9 billion between 1970 and 1980. They are continuing at a rate of $1 billion per year. Recent MSHA data indicate more than 50% of the longwall faces are still out of compliance with the 2 mg/m3 (0.00007 oz per cu ft) respirable dust regulation. Allowable dust limits are often further reduced owing to the presence of silica dust. This substantially increases the problem's severity. Research in the 1970s showed that by modifying the mining method through changing drum-type mining machines from high rpm shallow cutting to slow rpm deep cutting, both specific dust and energy could be reduced (Black et al., 1978; Ludlow and Wilson, 1982; Roepke, Lindroth, and Myren, 1976). The coal mining industry is using more longwall equipment to economically obtain high productivity. This high production rate, however, makes it difficult for longwalls to meet the legal dust standard. Research is showing how both these concerns may be addressed at the mining face. Results reported here explain the relationship of various major elements of the longwall system to dust generation on the longwall face. This paper is based on work completed by Foster-Miller Associates Inc. Objectives were to differentiate dust sources on the longwall face and to quantify dust levels for various elements of the shearer drum. The work was accomplished in two phases. Jonathon Ludlow, project engineer for FMA, developed and performed the necessary testing (Ludlow and Marshall, 1983). Bradley, Hadden, and Weston (1983) have done evaluations on British coal mines that produced similar results to those reported here. They found causative rela¬tionships between haulage speed, production, depth cut, drum speed, and dust generation. They also found that roof support movement increased the dustiness, whereas this work indicated that support movement had only a minor effect on total dust exposure. Both of these results are valid when the variation of mining conditions is analyzed. British mines are deeper than US mines. Therefore, roof rocks and coal are more fragmented than in the shallower US mines. Other reasons for the dust differences include the weaker shales found in Britain and the variation of roof support equipment designs between the UK and the US. Four mines in this report had rock roofs and, thus, would be less dusty. The fifth longwall mine had a coal roof, but the large cross-sectional area and high air velocity minimized dust exposure. Mines and Equipment Five underground longwall mine sites were tested (Fig. 1). All were using double-ended ranging-drum shearers (derds) with some variations in equipment. The mines and equipment details are shown in Table 1. No modification of mining equipment or operating cycles was made during the first phase of testing. The mining process observed followed the normal mine operating procedures. Three GCA RAM-1 respirable dust monitors and two vortex anemometers with cycle notations on portable tape recorders were used in each face area. The start and end of each cycle segment were recorded. Dust monitors record the dust levels once every 10 seconds, thus providing a relatively continuous real time indication of change in

Jan 8, 1984

By Melvin E. Poad

INTRODUCTION The placement of concrete by means of pumping is one of the fastest growing practices in the construction industry and is widely used in mining applications. In¬troduced in the United States in 1933, this method has been adapted to many aspects of the industry, especially where space for equipment is either limited or inaccessi¬ble. Concrete pumping offers many advantages over other methods of placement. Using pumping equipment, the concrete mixture can be transported in a single operation from a central mixing site to numerous forms in many remote locations, eliminating the need for rehandling the mixture and reducing the labor costs to a minimum. Pressurized pumping provides an extra mix¬ing and blending step, resulting in concrete of improved uniformity and greater density. In turn, this produces high compressive strength and increased durability. Various placement defects can be reduced or pre¬vented by pumping. The steady and even flow of the concrete minimizes the form distortion and delays caused by vibration problems that are common to fast dumping of the concrete mixes. Segregation, planes of weakness, bleeding, and surface faults are diminished considerably. Perhaps the greatest advantages of concrete pump¬ing are the distances and volumes that can be handled. Depending upon the equipment used, pumping rates of from 8 to 115 m'j/h (10 to 150 cu yd per hr) can be achieved, with a horizontal range of up to 460 m (1500 ft) and a vertical range of up to 140 m (450 ft). Theoretically, almost any concrete mixture could be pumped. However, consistency is an important consid¬eration for efficient operation. Mixes that are too wet, too dry, too hard, or poorly graded can cause difficulties that increase the costs. Similarly, mixes containing aggregate material that is over the maximum size or that is porous and highly absorptive can also result in diffi¬culties and increased costs. For the best efficiency, the mix formulation must have a well-graded sand and aggregate combination, with enough fines to provide flowability. If additional water is required for pumping, additional cement must be used to meet the design criteria of the structure. Each pump manufacturer can provide recommended mix formulations for the specific equipment furnished. Since the 1950s, many improvements have been made in pumping technology. Originally, only rigid steel pipe of 168 to 245 mm (6.625 to 9.625 in.) diam was used; today, both rigid steel pipe and flexible conduit are available in diameters of from 76 to 203 mm (3.0 to 8.0 in.). Improved pumps have been developed, and the introduction of power-coordinated booms has in¬creased the versatility of concrete pumping. The older and more conventional placement methods can no longer compete with the flexibility, efficiency, and econ¬omy of the pumping method, and continued research and development can only improve the system and expand its use throughout the mining industry. PUMPING EQUIPMENT The three major types of concrete pumping units currently available are the piston pumps, the pneumatic pumps, and the squeeze-type pumps. Table I provides a comparison of capacities, horizontal ranges, and vertical ranges for pumps of all three types. Piston Pumps The simplest of all concrete pumps are the piston¬type pumps; they are available from many manufac¬turers. As shown in Fig. 1, each unit consists of a

Jan 1, 1982

By Steve O. Green

Introduction The US coal mining industry is in the midst of a serious economic crisis. To overcome increased operating costs, operators must take advantage of technological advancements in mining systems and equipment. A relatively new concept available to underground operators is that of extending the cutting depth for continuous mining machines (continuous miners). This system is referred to as deep-cut mining, and may be described as mining cuts to depths greater than the standard 6 m (20 ft). Productivity is increased through the reduction in continuous miner tram time since the machine stays longer in each working face. To successfully implement a deep-cut mining system, three problems must be overcome: Exposing personnel to unsupported roof, methane removal, and controlling respirable dust. Remote control cutting The solution to the unsupported roof problem is remote control. Recent advances in remote operation, especially in radio remote controls, have resulted in what is generally accepted as a safe and reliable tool. By installing remote control on the continuous miner, the operator and helper can now be stationed in a supported area. This allows for improved visibility while cutting coal. With this in mind, the limiting factor now becomes the position of the haulage equipment operator. North River No. 1 uses Joy 21SC shuttle cars and Jeffrey 4110 diesel ramcars. These cars are pulled against the bumper of the continuous miner. Thirteen meters (43 ft) can be cut with the shuttle car and 14 m (45 ft) with the Ramcar before the operator of the car is inby permanent supports. By loading away from the bumper, about 1.5 m (5 ft) can be added, bringing total cut depths up to 14.5 and 15 m (48 and 50 ft), respectively. Methane removal The second problem involves methane removal, and the line curtain-to-face distance. In other words, how to maintain the line curtain to allow sufficient ventilation to remove methane and not expose workers to unsupported roof. The solution, in most cases, is to use a blowing-type ventilation system. Unlike the exhausting system that, to be effective, must be installed within 3 m (10 ft) of the working face, the blowing system can be effective at greater distances from the face. Numerous studies have documented the advantages of a blowing-type ventilation system over an exhausting system. Furthermore, a blowing system can be significantly improved by in¬creasing the velocity of the air delivered without increasing the volume of air. With this greater ventilation efficiency, it is possible to secure ventilation plan approval from the Mine Safety and Health Administration (MSHA) for a greater curtain set-back distance. This eliminates the need for personnel to travel inby permanent supports to extend the face brattice. The distance from the face MSHA will approve, however, is on a mine-by-mine basis. MSHA will evaluate the particular mine's face methane liberation rates, along with the specific proposals regarding face ventilation volumes and velocities. Dust control The third problem is controlling respirable dust. This is actually a result of the solution to the second problem. In the blowing system, while mining on the slab cut, both the continuous miner and haulage units are located on the dusty side of the line curtain (Fig. 1). In the early 1970s, underground operators virtually abandoned this system, in order to comply with the 2 mg/m3 (0.87 gr per cu ft) federal dust standards. The blowing face curtain did offer increased face ventilation efficiency. With that, greater curtain-to-face distances were also

Jan 8, 1987

By R. N. Chakravorty, R. J. Kolada

Introduction Spontaneous combustion in coal mining is recognized as a major hazard in terms of safety and economics. A survey by Olaf (1979) revealed that 80% of coal mine fires were caused by spontaneous combustion. Modern mining methods demand a high capital investment. Closure of a working face may then result in a huge loss. Even a short production interruption can prove expensive. Spontaneous combustion may also produce lethal amounts of carbon monoxide, thus posing a serious threat to the health and safety of underground miners. The worldwide recession in the early 1980s resulted in a number of mine closures and production cutbacks. So large stockpiles at mine sites were common. Experience has shown that stockpile fires are difficult to extinguish. Critical factors influencing spontaneous combustion There is no simple method of predicting whether a particular mining method applied to a specific coal seam will result in spontaneous combustion. Under favorable conditions of heat accumulation, spontaneous combustion can occur with any type of coal. It is known that subbituminous coals are more susceptible compared to low volatility bituminous coals, and that a high ratio of exinite increases the risk. However, the inherent moisture content of the coal and the exposed surface area may be more significant. Actual mining and ventilation conditions also strongly influence susceptibility. In practice, the experience gained with the mining method applied to a particular type of coal seam must be carefully evaluated with respect to the factors responsible for spontaneous combustion. Feng, Chakravorty, and Cochrane (1973) summarized the critical factors influencing spontaneous combustion in coal mines (Table 1). Prevention methods and strategies Mine layout is the most important factor preventing spontaneous heating. Working districts should be designed so that a particular section can be isolated on short notice without affecting production in others. Sites for preparatory seals should be identified and marked during planning. With coal seams that are highly susceptible to spontaneous combustion, the retreat method of working is preferred. This is because the gob is not subjected to a large difference in ventilation pressure. Coal pillars should be designed to resist excessive crush. The panel system of working is preferred, particularly for mining coals susceptible to spontaneous combustion. The size of each panel is calculated based on the incubation period and the rate of extraction. Controlling air leakage is also important for controlling spontaneous combustion. This is usually achieved by minimizing ventilation pressure difference, proper siting of doors, and avoiding unnecessary stopping and starting of fans. Air leakage is also reduced by sealant coating, injection of cements in cracks and crevices, and by maintaining good gateside packs. Application of inhibitors to control spontaneous combustion met with limited success. Chamberlain and Hall (1973) concluded that borate solution or Montan powder sprayed in the gob area or infused into a low rank coal would reduce the possibility of spontaneous combustion. Early detection of heating Significant research is being conducted worldwide to develop methods for early detection of heating. Monitoring combustion products during the early stage of heating is the most suitable method for detecting spontaneous combustion. The major gaseous products resulting from low temperature oxidation of coal are carbon dioxide, carbon monoxide, and water vapor. In mining operations, carbon dioxide monitoring is considered unsuitable because there are sources other than spontaneous heating from which this gas may originate. Carbon monoxide, however, is a more specific product of combustion during low temperature oxidation of coal. Over the years,

Jan 10, 1988

By Shan Mafi

he Broken Aro coal mine is located at the Woodbury Wildlife Preserve 11 km (7 miles) west of Coshocton, OH on State Route 541. Underground min¬ing at the 16-hm2 (40-acre) site took place during the 1910s. During the past five years, surface mining has occurred along the western and northern perimeters of the underground region. The Ohio Department of Natural Resources (ODNR), R&F Coal and American Electric Power (AEP) are involved in a project to remine the abandoned underground complex. The program also includes installing a mine seal made of fixated flue gas desulfurization (FGD) material. Previous mining activity in this area has resulted in an acid mine drainage (AMD) problem on portions of the reserve. In particular, a prominent AMD source is present in the Simmons Run drainage. The project goal is to eliminate or reduce the AMD that is discharging into the watershed. It was initially hoped that the Simmons Run drainage area could be economically mined. Accordingly, this area was included in the mine permit. However, experience with other previously mined areas on this reserve showed that the old mine workings were more extensive than originally thought. Old mine workings present several problems. The most significant are reduced coal recovery, poor coal quality and AMD liability. All of these problems increase mining costs. And the more extensive the old workings, the more significant the increase in cost. Based on R&F's experience with old mine workings in this area, it was decided that economic recovery of the Simmons Run drainage reserve was not possible. As a result, R&F excluded the Simmons Run drainage area from its early mine plans. Some time after it was decided not to affect the Simmons Run drainage area, R&F and ODNR's Division of Mining and Reclamation discussed the possibility of removing this area from the permit and attempting to correct the AMD problem as an Abandoned Mine Lands (AML) project. Specifically, the discussion centered around mining through a portion of the old mine workings to expose the mine openings in the highwall. Once exposed, the mine openings would be sealed using FGD material from the nearby Conesville power plant operated by AEP. In addition, there was interest in reclaiming the old tipple and associated gob pile located adjacent to Coshocton County Road 17 on the opposite side of Simmons Run. R&F attempted to eliminate the AMD problem by sealing the mine openings with FGD material. Once the seals were installed, they were covered with overburden. Monitoring wells were installed to determine the effectiveness of the seal and the inundation progress in the old mine workings as well as monitoring the quality of ground water. The project was jointly funded by revenue from the sale of the coal recovered during the project and AML funds. The FGD seal is expected to cause well water levels to increase above preseal elevations. However, the additional head pressure due to increased water depths in the underground mine may cause seepage through the bottom of the mine or out through the perimeter. The in¬creased water depth in the underground mine is expected to cause lower oxygen concentrations in the underground mine water. Since acidity is produced by oxidation of iron pyrites, less oxygen should result in better quality water. Monitoring wells will be installed before seal installation so that pre- and postseal water levels and well water quality can be determined. Surface sampling locations will be identified. These will be monitored before and after seal placement.

Jan 1, 1998