Search Documents

By S. G. Vick, K. E. Robinson, W. D. Webb

INTRODUCTION This paper discusses two uranium tailings waste disposal studies that reflect the United States Nuclear Regulatory Commission (NRC) regulatory actions and their changing requirements during the mid to late 1970's. Present guidelines require that all new uranium tailings impoundments be designed and constructed to eliminate, to the extent that it is reasonably achievable, exposures and risks to the public from the tailings. This includes positive measures for control of seepage losses from the impoundment and for control of radiological releases caused by wind and water erosion. Long-term stability of the reclaimed impoundment is also a very important requirement. That is, it is intended that the tailings impoundment, once it is reclaimed, will require little or no care or maintenance as long as the uranium tailings remain a hazard. Principally because of the long-term stability objective, the NRC has now identified subsurface burial of the tailings as the "prime option" for tailings disposal. The environmental implications of these proposed regulatory actions are obviously desirable. The economic implications the actions may have on a particular project are not always so obvious because they are so dependent on environmental suitability of site conditions. Selection of a site with favorable topographic, geologic and hydrologic conditions will usually result in the most economically and environmentally attractive alternative for tailings disposal. The first project discussed in this paper was initiated before the NRC guidelines had been developed to favour subsurface burial. At the beginning, seepage and radon emission control requirements were moderate. Constraints were imposed on the design by site topography, geology, and project capitalization considerations, factors which were dealt with according to straightforward engineering and design principles. More serious constraints were imposed by changing regulatory requirements. Unlike the more usual engineeringrelated constraints, regulatory requirements were upgraded during the design process, causing the design itself to undergo numerous modifications. The second project was initiated after the NRC proposed regulations had become better defined and below grade burial appeared to be the preferred

Jan 1, 1980

By Pooyan Asadollahi, Praveen Krishna, Michael Joye

"Durability design for underground structures is an increasing focus of designers and owners in the underground construction industry. Many owners have expanded their requirements for durability design, with specific requirements for structure lifecycle and designer certification of structural durability. This paper describes current trends and best practices including: defining the underground structure lifecycle, historically durable underground structures, design methods for underground structure durability built of reinforced concrete, and durability of materials. Criteria to be used for defining end of structure life and owner’s maintenance responsibilities are crucial to lifecycle contract requirements. Current practices of several major owners are presented. Design methods are presented including United States code requirements. Current best practices for enhancing the durability of materials used in underground construction are discussed including: low permeability concrete, steel reinforcement concrete cover, the use of steel fiber, and testing for verification. INTRODUCTION Durability design is increasingly being recognized as an essential component of good design practice. Infrastructure owners recognize that to serve the public interest, constructed facilities must be lasting and durable. The public understands that structures with limited service life result in increased costs and add to their daily inconvenience with frequent repair and reconstruction. Engineers are increasingly asking not only is the structure strong enough but will it last for generations. Durability design requirements are no longer just adherence to some accepted practices, but are based on analytical approaches, with results that can challenge our beliefs in what construction materials and details result in a durable structure. This paper describes current industry requirements and practices for durability design of underground structures, and offers some suggestions regarding future trends and developments. SERVICE LIFE DEFINITION The service life of a structure is the sum of the time to onset of deterioration, called initiation period (ti), and the subsequent time period of deterioration ending when the structure is no longer functional, called propagation period (tp). Figure 1 shows a conceptual service life diagram. These time periods can be substantially affected by the level of maintenance performed during the life of the structure."

Jan 1, 2016

By Laura J. Carroll, Gordon A. Goldsmith

Experts, like many of the speakers at the SME Annual Conference, are frequently called upon by lawyers to assist them in litigation. Due to the technical nature of many cases, the testimony of an expert with knowledge and experience in a particular field is necessary to help a judge or jury understand and decide certain issues. Environmental litigation is no exception. Experts routinely are called upon to offer testimony to establish the existence of contamination and its source, as well as the potential health and environmental risks associated with the contaminants. This article will briefly discuss the factors courts apply to determine whether to admit expert testimony after the recent Supreme Court decision in Daubert v. Memell Dow Pharm., Inc., 509 U.S. 579 (1993). The Court's decision in Daubert overruled a long-standing test that had based the admissibility of scientific evidence on its "general acceptance" in the field in issue. Next, the article will discuss in general terms what a party must do to "link a particular defendant's conduct to the contamination involved in order to recover from that defendant. This link, known as causation, varies depending upon the type of claim being asserted. Expert witnesses are used extensively to help establish causation. JUNK SCIENCE OR GOOD SCIENCE- HOW DOES A COURT DETERMINE WHAT TO LET IN A frequent complaint in litigation involving technical or scientific issues is that one party or another is trying to use so-called "junk science" to prove its case. While some expert testimony might be so clearly lacking in support or so "off the wall" that a court can easily determine to exclude it, other testimony, especially testimony on the "cutting edge," is much more problematic. In 1923, the District of Columbia Circuit Court of Appeals decided the case of Frye v. United States, 293 E 1013 (1923). In deciding whether to admit certain expert testimony, the court in Frye stated that while a court will "go a long way in admitting expert testimony deduced from a well-recognized scientific

Jan 1, 1998

By Hilal Soydan, H. Sebnem Düzgün, Jurgen Brune

In this study, with the primary goal of capturing ongoing digital transformation and automation impacts on the mining industry and its workforce, we conduct several interviews with mining industry experts in the United States and analyze our survey reports qualitatively and quantitatively through exploratory analysis. After the interpretation of the insights of industry experts, we proceed to generate a personalized and customized data analysis through a novel metric based on skills, knowledge, competencies and occupational requirements, which quantifies the job similarities for occupations in the mining industry based on the publicly available database of the U.S. Department of Labor. We use text analytics to tokenize and classify the interviews to capture a better understanding of major response categories. The temporal analysis shows that the critical competency needs in the data science and autonomy category increases from 28 percent in current demands to 43 percent. In defining our metric, we also calculate Kullback–Leibler (KL) divergence for each job profile that enables determining whether and to what extent that job is transitionary in our test set based on the mean, standard deviation and kurtosis of each job of interest. Our analysis reveals that the in-group job transitions are significantly easier than the between-group transitions, proving our initial assumptions and common sense. The generated heat maps provide the opportunity to present the gap between the current job and desired job profiles that provide feasible career change options, among others, offering individualized career paths for job seekers and promoting potential job transitions. Through the collection of industry-specific individual employee data, the AI system is envisaged to continue to learn as end users engage with the system, thus creating a central data hub specifically for the future workforce in the mining industry. Although the study has limitations on generalizability for qualitative assessments, it presents itself as a valuable application of how qualitative and quantitative approaches could be of value for future worker training in the mining sector.

Feb 1, 2025

By Éder Domingos Oliveira, Carlos Antonio Morais, Ruberlan Gomes Silva

The objective of this work was to assess the influence of parameters such as residence time, solid content, and temperature in a process route towards purified rare earth liquor which could be adequate to produce marketable rare earth products. The steps of the process route proposed in this study comprised water leaching of a sulfated rare earth ore and removal of impurities through the purification of the rare earth sulfuric liquor, which is the product of the water leaching step. The sample used in the water leaching experiments was a sulfated rare earth ore produced by the reaction of a beneficiated rare earth ore with sulfuric acid followed by roasting at 700 °C for 2 h in a muffle furnace and cooling at 20 °C. The water leaching experiments showed that the best condition comprised a residence time of 30 min, temperature of 20 °C, and solid content of 10% w/w, resulting in a recovery of 71.3% of the rare earth elements (REE) and a lower impurity extraction, e.g., only 15.0% of Fe, representing the main impurity in the rare earth ore. Even when presenting low amounts of impurities, the rare earth sulfuric liquor still needed to be purified before it can be used in the production of marketable rare earth products. In the study, the rare earth sulfuric liquors were purified in two consecutive neutralization steps, first by dosing the limestone pulp to pH up to 3.5 and secondly by adding the lime pulp to raise the pH from 3.5 to 5.0. The application of two consecutive purification steps at 20 °C resulted in the highest overall REE recoveries (65.4%) throughout all the steps of the process, being 71.3% in the water leaching, 99.6% in the partial purification with limestone pulp, and 92.1% in the purification with lime pulp at 20 °C. Under this condition, there was a total elimination of Fe, P, and Th and a significant reduction in the Al, U, and sulfate concentrations in the purified rare earth liquor. The purified rare earth liquor attained through the experiment is expected to be amenable to be used in the production of marketable products due to the lower impurities/REO mass ratios.

By S. K. Kawatra, S. K. Valluri, S. J. Root

Carbon dioxide, a by-product of combustion reactions, is a greenhouse gas linked to climate change. At Michigan Technological University, we have studied the capture of CO2 using alkali scrubbing solutions in a pilot scale packed bed counter-current scrubbing column. To do this, we have simulated flue gas by combining streams of CO2 and compressed air. Real flue gas has impurities such as CO, SO2, and NOx, and has lower levels of O2 than our simulated flue gas. In order to study CO2 capture from a real flue gas, the Department of Chemical Engineering worked with the Facilities department to install a pilot scale scrubbing column in the Michigan Tech steam plant. Experiments were conducted using a sample stream of the flue gas from the boiler in the steam plant. Data collected from these experiments were compared to the data collected from identical experiments conducted on simulated flue gas in the lab. The capture efficiency of the real flue gas scrubbing column is discussed in this paper. BACKGROUND The most common equipment used to separate CO2 from a flue gas stream is a counter-current packed-bed scrubbing column. The department of Chemical Engineering at Michigan Technological University has two such pilot scale columns. In order to study the effect of impurities found in real flue gas, one is installed in a controlled laboratory using a simulated flue gas created by mixing CO2 and compressed air. This column will be used to establish a baseline for percent capture analysis and is displayed by figure 1. The second scrubbing column is identical to the first, and is installed in the Michigan Tech central energy plant. The plant produces up to 130,000 lb/hr of 80 psig steam to provide hot water and heat for campus buildings. A typical wintertime load burns around 25,000 SCFH of natural gas; this load releases 1.4 metric tons of CO2 per hour. The flue gas the steam plant produces is roughly 7.5% CO2 by volume. In order to study CO2 capture from this flue gas, a tap has been installed on the main exhaust duct which draws a sample of the flue gas into the pilot scale scrubbing column. Figure 2, a simplified diagram of the steam plant, shows that the tap was installed between the economizer and the stack condenser.

Jan 1, 2019

By Frank A. Aplan, Barbara J. Arnold

INTRODUCTION Coal flotation is a fine cleaning process usually present in all but the older preparation plants. It is typically used to clean either the -28 mesh (-500 pm) or - 100 mesh (- 150 pm) raw coal fines, and it is the only commonly used preparation method that can effectively recover coal particles finer than, say, -200 mesh (74 pm). To place coal flotation into its proper context, it should be noted that the bulk of the raw coal sent to preparation plants is treated by gravity concentration. On a worldwide basis, from 0 to 40% of the raw feed to a preparation plant is treated by flotation, while in the US only about 10% of the raw coal feed is floated. Roughly, 50% of US preparation plants use flotation to process at least a portion of the raw coal feed, although most of the newer plants incorporate flotation into their flowsheet. Historically, the process has only been used to treat the raw coal fines naturally occurring after mining and a minimal amount of crushing at the preparation plant. This is in sharp contrast to ore flotation where, typically, the entire tonnage is first ground and then floated. As a consequence, of the approximately 500 Mt of raw coal treated by preparation in the US yearly, it is estimated that only about 40 Mt are sent to the flotation circuits (producing -30 Mt of clean product).'O1 This small tonnage compares with about 400 Mt of ores treated annually in the US by flotation. By analogy to ore flotation, where it is an effective, large tonnage, low cost, easy to operate process, its potential in coal preparation should be great. Reasons why it has not achieved a greater potential in coal preparation have been attributed by Aplan 102 to: 1. Indifferent results in removing sulfur and ash. 2. Difficulty in floating low rank and oxidized coals. 3. Inability to make clean separations with the finer sizes. 4.Inability to clean slurries with a high percentage of clay. 5. Problems with water chemistry. 6. Competition with effective, gravity coarse-cleaning methods. 7. Low value of coal historically. 8. Dewatering problems. 9. Transportation and storage problems with coal fines. 10. Marketing problems with coal fines. 11. Inadequate attention to the process in the plant. 12. Inefficient use of capital and operating monies. Inadequate attention to procedures, machines, and processes.

Jan 1, 1991

By Earle J. Klohn

INTRODUCTION The paper presents a broad overview of the geotechnical site studies required for siting uranium tailings dams. These studies, which are interdisciplinary in nature, touch upon such related fields as: hydrogeology, hydrology, and seismicity. Tailings dams are commonly used to develop tailings ponds for the storage of the waste products generated by mine milling operations. In the past, most tailings ponds have been developed either above ground on dry land, or in existing lakes. In the United States a majority of the uranium mines are located in arid or semi-arid regions and past practice has been to store the wastes above ground on dry land (1,2). Currently, the United States Nuclear Regulatory Commission (N.R.C.) recommends below ground disposal of uranium waste products, although they indicate that they will consider above ground alternatives (3). In Canada many of the existing uranium mines are located in a wet environment and past practice has been to use small lakes and depressions as tailings ponds (1,4). However, current practice in Canada leans towards above ground, dry-land storage (5,6,7), and the Atomic Energy Control Board (AECB) guidelines (5) indicate this to be the preferable method. In B.C., where a moratorium on uranium mining has been declared by the Provincial Government, there are no existing uranium tailings ponds. However, both the formerly proposed Birch Island and Blizzard uranium developments would have used dry land storage. Most of the existing non-uranium mill wastes in B.C. are stored behind tailings dams on dry land. The waste products delivered to the tailings pond comprise, the ground-up rock that remains after most of the uranium values have been removed and the excess chemicals used in the milling process. These waste products, which are called "tailings", are normally mixed with water to produce a slurry and then pumped to the tailings pond. Since the uranium recovered constitutes only a small percentage of the ore (usually less than 1%) (8), large quantities of waste rock and associated transportation water are discharged into the tailings impoundment area. Consequently, relatively large tailings pond areas are required for the uranium tailings. In recent years, major advances have been made in the design, construction, and operation of non-uranium tailings storage facilities (9,10,11,12,13,14, 15). These improvements have been based on combining the latest advances

Jan 1, 1980

By Kegomoditswe Koitsiwe, Tsuyoshi Adachi

"This paper characterizes quarterly LME copper price fundamentals from 1995 to 2011 by analyzing the transformation of the market mechanism based on structural change perspective. Using chow test for structural change based on the least square multiple regression, we divide the price fluctuation into: Stable price period (1995Q3-1999Q2), Low stable price period (1999Q3 – 2003Q3) and Price fluctuation period (2003Q4 – 2011Q2). The results show the existence of structural breaks disproves the investigation of the full sample period as a whole. In different structural breakpoints the main drivers of copper prices changes and their impact are significantly different. Moreover, the paper examines the role of speculation in copper price fluctuations.Introduction The rise in commodities price volatility and financial and economic crisis have led to questions over the organisation of futures and physical commodities markets. Spikes in commodity prices and volatility have coincided with a surge in financial speculators in the commodity markets inspiring a polarised and hotly debate among academics and practitioners about the role of investors in the development of physical markets. In his seminal work Kaldor (1939) focused primarily on whether speculative activity in the futures markets reduces the variance of commodity spot prices. Yet, part of the literature finds that the introduction of futures contracts destabilizes the spot market. IMF (2006) studied commodities boom and its causes concluding that there is little support for the hypothesis that speculative activity affects either price levels over the long run or price swings in the short-run. The impact of speculative activity on commodity prices remains a highly contentious topic. Other market analysts take the view that the supply and demand for physical commodities remain the major determinants of market trends (Krugman 2008). It is the aim of this study to contribute to the literature by examining the drivers of copper price changes from a structural change perspective. In this context we are attempting to answer to: What are the main drivers leading to copper price fluctuations? Are these factors having the same effect in different periods or not? It is meaningful to understand drivers of copper prices and thereby, their fluctuations because it will help developing countries depending on copper export to anticipate market situation and avoid bad economic development challenges that can result from price fluctuations. Moreover, this can ensure sustainable mineral supply."

Jan 1, 2017

By Carlos A. Jaramillo, Seng Hing Ngu

"The Murum Hydroelectric Project is a 944-MW development consisting of a 145 meter high RCC dam, two 2660 meter long, 9 meter excavated diameter upper pressure tunnels, surge shafts, two 950 meter long 7 even meter OD penstock tunnels and a surface powerhouse. The project is located in the eastern section of the State of Sarawak, Malaysia, about 200 kilometer from Bintulu, in the Rajang Fold-Thrust Belt, an Upper Cretaceous to Upper Eocene fold and thrust belt that extends under most of Sarawak. The Belaga Formation consists of a thick sequence of deep marine sediments currently appearing as steeply dipping strata of thin to thick bedded, fine to medium grained sandstone interbedded with argillaceous rocks, resulting on a “Flysch” type geologic environment. The project pressure tunnels were excavated perpendicularly to these strata resulting on frequent change on rock conditions and behavior, and required rock support. This paper describes the characterization of the rock mass, design of rock support, and incidents during construction. Particularly interesting were convergence issues in Tunnel 1 resulting from Tunnel 2 excavation. INTRODUCTION The Murum Hydroelectric Project is located in the eastern section of the State of Sarawak, Malaysia, about 200 kilometers from Bintulu, and upstream of the Bakun Hydroelectric Project. The project consists of a 145 meter high RCC dam, a 50 meter high intake tower, two nine meter OD and 2660 meter long upper pressure tunnels, two nine meter OD and 175 meter long vertical shafts, two 25 meter diameter and 80 meter deep surge tanks, two seven meter OD and 950 meter long penstock tunnels and four seven meter OD and 50 meter long branch tunnels, two 8 meter diameter to 3.4 meter diameter and 1400 meter long penstocks installed within the shafts, penstock tunnels and branch tunnels ending in a powerhouse with 944 MW installed capacity. LAYOUT OF THE WATERWAY TUNNELS The two waterways tunnels are basically parallel as shown in Figure 1, with each tunnel supplying water to two units in the powerhouse. The tunnels start separated 25 meters center to center, but 250 meter from the intake the separation increases to 35 meters. The tunnels are lined with reinforced concrete until they reach the surge shafts and steel lined from there to the powerhouse. The tunnel profile is shown in Figure 2."

Jan 1, 2016

By Peter P. Harvey

The Nonel Primadet is a non-electric blasting initiation device. The system incorporates the safety advantages of a cap and fuse system with the precision blasting afforded by electrical blasting caps. Each unit is made up of a delay blasting cap factory-crimped to a Nonel® shock tube lead line. The delay elements in the blasting caps are manufactured in both millisecond and long period series. There are 16 periods available in both series - period 0 through period 15. The units are manufactured in 12', 16', and 20' lead lengths. The hollow shock tube is made of surlyn plastic and it is coated on the inside with a reactive material. The powder train has a density of only 1/10 grain per linear foot of tube. A typical blast round is timed precisely the same way it would be with electrical caps. After the round has been timed and loaded, the tube leads are gathered in convenient bunches and tied into a detonating cord trunkline. The Nonel® tube bunches are initiated by the output of an 18 grain per foot detonating cord trunkline. Once initiated, the Nonel® shock tube will reliably propagate at 1800 meters per second. The energy from this shock front initiates the delay elements in each delay cap. The shock tube is inert to electrical energies, including; stray current from AC/DC power sources, as well as, electrostatic discharges. The tube is also inert to initiation by impact. The system has proven to be particularly advantageous in both tunnel and shaft blasting applications. The major advantages in using the Nonel® system in this type of work are: 1) faster and easier tie-in techniques through the use of bunch-blasting. 2) electrical power can be left on during loading and tying-in. a. electrical lights can be turned on at the working face - better lighting facilitates loading and tying-in. b. electrical pumps can continue to function throughout loading and priming procedures (this is particularly advantageous in shaft work with water problems). 3) down-time due to approaching electrical storms is minimized. 4) increased overall efficiency in the blasting cycle: a. it is easier to train a man in the proper use of the system. b. fewer missed holes per round. c. less time required for tie-in. 5) safety-advantage--The system is not susceptible to involuntary initiation from extraneous electrical energies.

Jan 1, 1979

By Joseph Fernandez, Luminita Calin

INTRODUCTION The Tunnel and Reservoir Plan (TARP), commonly known as the Deep Tunnel Project, is the daring and unique concept developed by the Metropolitan Water Reclamation District of Greater Chicago (MWRDGC) as a two-phase solution to the problem of waterway pollution and basement flooding due to sewer system backups created by the combined sewer over-flows (CSOs). Phase I, primarily for pollution control, includes the tunnels, shafts, connecting sewers and structures. These Phase I facilities intercept, during wet weather events, the CSOs within the MWRDGC TARP service area. The tunnels and shafts provide temporary storage of the CSOs for subsequent treatment at Water Reclamation Plants (WRP) before discharging into waterways. Ultimately, upon completion of Phase II, the tunnels, located from 45 m(150 ft) to 100 m (330 ft) below ground, will convey the CSOs to reservoirs for storage until WRP capacity is available. Phase II, which includes the reservoirs, pumping facilities, additional tunnels and shafts, has been planned to serve a dual purpose. The reservoirs provide storage of excess flows during wet weather events, those beyond the WRP capacity. Following the wet weather events, the stored flows can be conveyed, at controlled rates, to the WRPs for full treatment. These excess flows previously would have resulted in both overflows into the waterways and eventually backups in the local sewer systems. The storage capacity of the reservoirs also will promote the full utilization of the conveyance capacity of the tunnels and shafts, which in turn results in optimizing the conveyance capacity of the existing sewer systems. Therefore pollution control is further enhanced by allowing for capture of a greater volume of CSOs and greatly minimizing backups in the local sewer systems. The TARP project consists of four systems: O’Hare, Mainstream, Des Plaines, and Calumet, covering a total area of 971 km2 (375 mi2) and serving the City of Chicago and 51neighboring communities as shown in Figure1. With only two contracts left before completion of the Phase I tunnels, the 12.7km (7.9mi) Torrence Avenue leg, to be awarded in 1997, and the 12.4km (7.7mi) Little Calumet leg unfunded as of yet, both part of the Calumet System, the pollution control phase of the project is now 86% complete (Table 1).

Jan 1, 1997

By H. Knorre, A. Griffiths, J. Loroesch

Introduction Hydrogen peroxide is known to the mining industry as a powerful oxidant, able to attack and to destroy cyanide, the most important leaching reagent (Knorre and Griffiths, 1984; Griffiths, 1988; Griffiths, 1988). CN- + H202 => OCN- + H2O The most recent development, however, is the use of H202 as an oxidant in the cyanidation of precious metals. This application may appear to be a contradiction to the above mentioned detoxification process. This can, indeed, be the case if certain conditions are not considered carefully. Degussa has developed a new process to enable the application of H2O2, in this field without having any detrimental effect on the cyanide. The incentive to seek an oxygen supplier like H2O2 instead of air was the fact that one of the most important conditions for the fast dissolution of gold is the presence of physically dissolved oxygen in the pulp (Kydryk and Kellog, 1954; Warstell, 1987). 2 Au + 4CN- + 1 /2 O2 + H2O => 2 [Au(CN)2]- + 2 OH Complete gold recovery within a reasonable leaching time may only be achieved if the pulp is saturated with dissolved oxygen. Gold losses in leach operations mainly occur due to the following reasons: • In some cases, the saturation of oxygen in the pulp cannot be achieved by aeration due to the difficulty to transfer oxygen from the gaseous into the liquid phase. This happens, for example, in pulps with a high viscosity. In such cases, even violent aeration only results in a low concentration of dissolved oxygen in the pulp. • In any case, the starting phase of leaching requires the highest amount of oxygen. Therefore, it is especially important to raise the dissolved oxygen level to saturation in the starting phase. Peroxide assisted leach process (PAL) The intention of the process is to introduce oxygen in a liquid form. As a result of intensive research work, it could be shown that hydrogen peroxide can be used as a source of oxygen in the leaching of gold ores. To avoid side reactions, the following conditions must be applied: • Hydrogen peroxide must be diluted before it is added to the pulp. • The dosage of H2O2, must be properly regulated based on the oxygen level of the pulp. • An important part of the continuous 02-control is a special oxygen electrode, which resists the extremely abrasive action of the pulp.

Jan 1, 1989

By Stephen Leslie

A multimedia tutorial illustrating the geology and mineral resources of Gulf Coast salt domes has been developed as a pilot project for a course on Texas geology and resources at the University of Texas at Austin. The principal objective of the tutorial is to educate students with limited background in geological sciences about a major local geologic feature and its geologic and economic significance. The content of the tutorial represents materials generally covered in 4 hours of lecture and laboratory instruction. These materials are presented using a flattened hierarchy of topics, each accessible from a central menu, including salt-dome history, salt tectonics, anhydrite and calcite cap rocks, mineral resources, and geophysical character. Information concerning salt-dome geology is communicated using interactive software; sound and animation are used throughout to reinforce key concepts. Visual aspects include field views, hand specimens, and photomicrographs that were digitized from slides. Illustrations were created using a graphics program or scanned from available archives. Each visual element has an accompanying explanation, which in many cases is linked to other parts of the tutorial. Navigation is accomplished using hyper-links or a set of unobtrusive buttons. The program includes a glossary of the major minerals associated with salt domes available as a pull-down menu and digitized video footage of the Gulf of Mexico sea floor to illustrate the active environment of the formation of the salt-dome cap rock. In addition, a group of interactive questions is presented to assess the level of mastery. Technical aspects were accomplished using a Power Macintosh ? 7100AV and a variety of commercial software. Actual linking of information was done with Authorware? 3.0 Educational, an icon-based, multimedia authoring program. Graphic illustration was done with Adobe Illustrator ?; image processing was accomplished using Adobe Photoshop?; video was cap¬tured, edited, and compressed using Adobe Premiere ?. The interactive nature of the project was designed with regard to future means of dissemination, especially on the World Wide Web. This tutorial serves as a template to build additional modules covering the entire course. A modular approach to the coding of the project and extensive self-documentation should ensure the viabil¬ity of the project by allowing other workers with moder¬ate computer skills to complete other lessons within the curriculum framework.

Jan 1, 1999

By Michael Drozd

Introduction Flotation is a recovery process that utilizes natural or chemically-introduced hydrophobicity of minerals to separate ore from gangue by attaching the ore particles to bubbles. Flotation has been known since 1906, when it was patented by E. L. Sulman, H. G. K. Pickard and John Ballot. Flotation's first documented plant use was in 1911, when it was used on gravity tailings from a zinc plant. Cyanide leaching was first patented in 1887. Most early precious metals flotation was linked to lead or copper concentrates. Most precious metal flotation is linked to sulfide recovery and utilizes such reagents as xanthates, dithiophosphates and thiocarbanilides. But the involvement of flotation in precious metals recovery does not have to be limited to active flotation of the gold and silver bearing minerals. Flotation can be used to remove interfering minerals, such as carbon, or cyanicides, such as copper, arsenic bearing minerals or other cyanide complexing minerals. Cyanide Leaching The use of cyanide to recover precious metals is the backbone of the industry. The various recovery processes that use cyanide are: 1. Leaching-Counter Current Decantation(CCD) Merrill-Crowe 2. Carbon-in-pulp (CIP) 3. Carbon-in-leach (CIL) 4. Vat leaching 5. Heap leaching These processes are selected depending on ore grade, ore leaching characteristics, reserve size and capital limitations. Ore grade is used as the first criteria to determine the type of cyanide plant required. However, the reserve size can determine whether a ground ore alternative is used. The ore leaching characteristics may indicate that the higher recovery, associated with a process that employs grinding, is the only economic recovery alternative. There are some extremely large leaching plants with grades that would be non-economic for some existing heap leach plants. Many factors, such as strip ratios, metal recovery and reserve size, determine what the ultimate plant design will be. The exact processing scheme that is used, is a multifaceted decision matrix, which gives the process metallurgist some job security. Precious Metal Recovery Using Flotation Flotation recovery can conceivably be used on any ore that has been ground. Many operations utilize gravity separation on the ore to remove native gold from the ore prior to sending it to cyanide leaching. On certain ores, where the gold is in visible nuggets or particles, this processing alternative is advantageous because the native gold cyanide recovery is

Jan 1, 1993

By Houston Kempton, Tim Dyhr, Andy Davis, Mark Bloom, Connie Travers, Dave Atkins, Jeff Deen

INTRODUCTION Historical mining activities in the Robinson Mining District, in the Egan Range of east-central Nevada (White Pine County), resulted in five open pits (Veteran, Tripp, Liberty, Ruth, and Kimbley Pits), several large mine-waste dumps, and numerous underground workings developed for copper, zinc, gold, lead-silver, and manganese (Figure 1). Groundwater percolating downward through the copper sulfide ores produced a blanket-like supergene zone enriched in copper, which has been one of the primary objectives of mining since the early part of this century. To obtain permits for future operation, an EIS was conducted that evaluated future pit- lake chemistry, groundwater quantity and quality issues, transport of water and solutes subjacent to a proposed tailings impoundment, and the potential for waste dump acidification. AREA HYDROGEOLOGY The mine area is on a ridgeline draining to the Steptoe Valley to the east and to the White River Valley to the West. Precipitation in the Robinson Mining District ranges from a low of 15 cm (6 in.) per year in the valley to more than 50 cm (20 in.) per year in the surrounding mountains. Evapotranspiration exceeds precipitation, leading to a net loss of water from the basin as either surface flow or underflow to the north at Currie, Nevada (Eakin et al. 1967). The White River Valley, which lies to the south and west of the mine area, includes approximately 4,200 km2 (1,620 mi2) of the upper part of the Colorado River Basin. This valley is 112 km (70 mi) long, 32-48 km (20-30 mi) wide, and like Steptoe Valley, evaporation and transpiration exceed precipitation (Maxey and Eakin 1949). The local groundwater flow system in the Robinson Mining District and the proposed mine area is dominated by two main components: (1) a groundwater mound or high between the Ruth Pit and Murry Springs, and (2) a shallow groundwater flow divide that follows the ridge crest south of Ruth, which contains the Veteran and Tripp pits. Besides the alluvium, the main hydrostratigraphic units controlling groundwater flow are limestones, shales, and sandstones, along with the intrusive quartz monzonite stocks. Based on the piezometric surface measured in October 1993, three distinct groundwater regions were identified. In the Giroux Wash area, an apparent fault runs between WCC-G1 and WCC-

Jan 1, 1995

By Zbigniew Hladysz

INTRODUCTION In the Polish coal mining industry, the Upper Silesian coal basin has an important position. It contributes over 98% of the total coal production of Poland which reached 193 mt in the year 1979. In view of the significant urbanized area in this region as well as the industrial potential, it is important to protect the surface by stowing the mined out underground workings. Approximately 18% of the total production is mined from longwall faces with stowing. However, caved longwall faces are most popular. In the upper Silesian coalfield, approximately 337 highly mechanized longwall faces are in operation. Out of these 337 faces, 301 longwall faces are caved. One of the main requirements for effective and safe coal extraction is a suitable method for strata control. We can divide the complex process of strata control into four steps: 1. Strata investigations 2. Selection of supports for roadways 3. Selection of supports for longwall 4. Rock bursts and other hazards protection STRATA INVESTIGATIONS Estimation of the structure and physico-mechanical properties of the rock mass surrounding the workings is an important constituent of strata control. These factors definitely influence the rock stability, support load, working conditions as well as the mining technology. Complex methods of strata investigations involve a set of indicators enabling the estimation of the stability of the roof rock, strength of the coal seam and load bearing capacity of the floor. The basis for the evaluation of roof stability for a coal seam is the classification according to the resistance to bed separation (1). The bed separation resistance is equal to the strength of the rock in tension perpendicular to the bedding plane. In order to properly classify a rock, it is indispensable to make continuous profiles of the bed separation resistance from the immediate roof up to a distance of three times the thickness of the coal seam. The profiles are developed by utilizing mine roof investigations with the hydraulic borehole penetrometer. (Fig. 1) The penetration resistance is determined by the critical pressure required to cause crushing of the rock by the penetrometer indentor (2). The classification of roof rocks and their ability to cave spontaneously during longwall mining is shown in [Fig. 2]. The measurement of the critical pressure also allows for the determination of the compressive strength of the rock, the index of workability and roof fissuration.

Jan 1, 1982

By Kwadwo O. Adutwum, George M. Potter, Todd J. Harvey

Ashanti Goldfields Company (AGC) is the largest gold mining company in Western Africa. Their jewel operation is a highly inte­grated set of mines and plants situated in Obuasi, in the Ashanti region of Ghana. This operation is responsible for mining 5.5 mil­lion tonnes of ore at 4.6 git annually from a series of open pits and underground mines. The sulphide ore is highly refractory with untreated gold recoveries in the range of 30-40%. The milling facilities are quite varied and include an oxide treatment plant (OTP), a heap leach, a sulphide roaster circuit (PTP), a tailings treahnent plant (TIP) and the most recent, a sulphide treatment plant (STP). The sulphide treatment plant, the world's largest stirred tank biooxidation circuit, was commissioned in early 1994. This plant treats approximately 800 tonnes of refractory gold con­centrate per day with overall recoveries of75-85o/o(ll, Biooxidation was selected for its ease of operation and less exotic maintenance requirements as well as its ability to achieve comparable gold recoveries. Unfortunately, despite stirred tank biooxidation being one of the lower cost methods of treating refractory ores, it is still too costly for low grade refractory materials. GeoBiotics, Inc. has developed a proprietary technology that allows the economic treatment of lower grade refractory gold ores through heap biooxidation. AGC has a significant resource of low grade refractory sulphide ore. This ore is too low grade to warrant BIOX™ sulphide treatment and its oxide plant recov­ery is low at 35-45%. GeoBiotics and AGC have completed pre­liminary testing and economic analysis of heap biooxidation for this material. Additionally, the feasibility of producing a gravity concentrate from the tailings of the sulphide treatment plant has been explored. This concentrate would be coated onto the low grade sulphide and biooxidized concurrently. Gold recoveries for the biooxidized low grade sulphide have increased to 75% and the gravity recovery from the STP tailings has achieved 80% uti­lizing a Falcon concentrator. The preliminary economics of the proposed full scale plant are very favourable with a pre-tax IRR of 233% and a payback period of 6 months. This paper details the biooxidation testing, flow sheet devel­opment and preliminary economics of employing heap biooxi­dation for low grade refractory ore treatment at Ashanti Goldfields' Obuasi operation.

Jan 1, 1998

By Doug Williams, Kent J. McGrew, Dr. Jack Murphy

For some time, selenate has eluded water treatment by conven­tional means such as precipitation and clarification. This has been due to the nearly universal solubility of all oxidized sele­nium species, the low levels required for surface discharge, and almost identical chemical behavior to all forms of oxidized sul­fur. The last characteristic makes selenate particularly difficult to deal with in acid mine waters where sulfate can easily be on the order of one gram per liter. Approaches such as ion exchange or reverse osmosis often tum into total demineraliza­tion schemes for the sake of removing a "trace" selenium species that may be present on the order of 108 sulfate/selenate. Reduction of selenate to selenite or elemental selenium by chemical means has been relatively unresearched. Some limit­ed success has been reported (Murphy, 1988) using ferrous hydroxide as a reducing agent; however, the reaction time as reported is too slow to be useful in a practical plant design. One significant difference between selenate and sulfate is that selenate has been discovered to be reducible in acid solution by elemental iron when catalyzed by soluble copper. Since the +4 or zero valence states of selenium are rather easy to deal with by coprecipitation with iron salts or alum, the elemental iron dis­solved in the process contributes to the overall process by pro­viding sludge upon raising the pH that can be separated by con­ventional clarification. Commercial production of selenium using copper catalyzed reduction of selenite to selenium metal via sulfur dioxide is well established, however, at the < 5 ppb requirements for surface discharge this reduction process equili­brates at levels far too high to be useful to low level selenate removal criteria. The reaction reported herein uses elemental iron for reduction of selenate with copper acting either as a cata­lyst or as a coprecipitation agent. This method, employed with conventional sludging, clarification and filtration can provide an economic method to achieve non detectable selenium (< 0.005 mg/I). Iron consumptions for the conditions tested have been on the order of 3 lbs/1,000 gallons treated. This represents as little as $0.06 or $2.00 per 1,000 gallons based on using a scrap source of iron or the purchase of electrolytic iron for the process.

Jan 1, 1996

By John D. Abbatt, H. B. Newcombe

The Eldorado Epidemiology Project formally began in late 1978. It consists of a retrospective cohort study, to be followed by and to leave in place the mechanism for a prospective cohort monitoring program. These present and future activities are intended to merge into one another. The current study includes all Eldorado employees past and present for whom records are available. The objectives of the undertaking are - 1) to obtain cause-and-effect, dose-response data with which to evaluate the risks to workers in radon and radon daughter containing atmospheres, and to provide additional quantitative information on which to base possible improvements in working conditions; 2) to identify any dead employees of E.N.L. whose cause of death suggests that a potential compensation claim right exists for their survivors, and to similarly identify living ex-employees of E.N.L. whose work histories and states of health suggest potential compensation claim rights. The nature of the study has been determined by the history of Eldorado, which will be described briefly. Eldorado began (as Eldorado Gold Mines) in the late 1920&apos;s, operating relatively unsuccessfully in Manitoba. In 1930-31 the emphasis shifted from gold to uranium, and what became the Port Radium mine was first staked. From the very early 1930&apos;s until 1942 the company&apos;s purpose was almost entirely devoted to the mining of pitchblende - uranium ore - from the Port Radium site, and the extraction of radium from this ore at the Port Hope refinery in Ontario, a process from which the uranium was a largely stockpiled byproduct. In 1942 the company was requested by the Canadian government to accelerate the production of ore, and of uranium. At the same time, all its stockpile of uranium (then being stored in silos as a "waste" product which might later "come in") was acquired for the Manhattan Project. In 1944 the company shares were bought by the Canadian government and the company itself became Eldorado Mining and Refining (1944) Limited; it has operated as a Crown corporation ever since. The name was changed to Eldorado Nuclear Limited in 1968. The Port Radium mine was closed in 1960, and since 1953 the Beaverlodge uranium mine complex has operated on the northern shores of Lake Athabasca. Radium production was discontinued in 1954 when the radium circuit was taken out of the refinery, and since that time the refinery&apos;s products have been various types of refined uranium (uranium dioxide, uranium trioxide and uranium hexafluoride) plus metallic uranium. The refinery, of course, processes the company&apos;s own yellowcake but as it is one of only five refineries in the western world, most of its work consists of custom refining for a large variety of customers. In addition to the mining and the refining operations, there have been three other divisions involved, and these are, respectively, Aviation, R. & D., and Exploration, in addition to the financial, corporate, administrative and support activities. MATERIAL AND METHODS The human study population (Abbatt, J.D. et al., 1980) consists of all Eldorado employees who have ever worked for E.N.L. and for whom records are available. The total nominal roll to December 31, 1980 is approximately 21,000 and consists of employees of the Mining, Refining, R. & D., Aviation and Exploration Divisions, as well as a relatively small number of other employees (Head Office, etc.). The basic epidemiologic design, as has been mentioned, is for a retrospective cohort study merging into a prospective cohort study, and depending very heavily upon automated record linkage and file matching. The original design called for an initial assembly of the bulk of the nominal roll, prior to the first of two matches with the National Mortality File. The first of these two matches is now complete and the second is to be separated from it in time by 18 months to two years. The second match will be the definitive match prior to the analysis, the interpretation of the data, and the publication of the results. The period between the two matches was designed to permit completion of the nominal roll, including: - addition of previously missing individuals and groups, elimination of duplicates, and amplification of identifying information, - assembly of work histories and exposure information for each individual, - digestion and application of lessons and modifications resulting from the first match with the National Mortality File at Statistics Canada, - preparation of files for the definitive second match. The analysis of data will be carried out by the National Cancer Institute of Canada Epidemiology Unit based at the University of Toronto. This group, with whom Eldorado Nuclear has a memorandum of understanding, have for a variety of reasons, including their familiarity with record linkage and their expertise, been members of the Project Team since

Jan 1, 1981