Search Documents

By Austin Whillier, Duncan Mitchell

The problem of heat stress underground in the gold mines is approached on the basis of the heat transfer between the human body and the underground environment. Experimental measurements of radiant and convective heat transfer and a theoretical calculation of maximum evaporative heat transfer enable the maximum cooling power of an environment to be calculated in terms of the dry-bulb and wet-bulb temperature, the mean radiant temperature, the wind speed and the barometric pressure. For most underground applications the cooling power can be expressed as a function of wet-bulb temperature and wind speed only. The relative importance of wind speed and wet-bulb temperature can be assessed: in working places where wind speed is low additional cooling of workmen can be achieved better by increased wind speed than by decreased wet-bulb temperature. The wet kata reading proves to be of limited value as an index of heat stress because environments with equal wet kata do not necessarily have the same cooling power. Finally, thermal equilibrium with the environment is possible when cooling power equals or exceeds the rate of metabolic heat generation. The rates of metabolic heat generation for various underground tasks are indicated.

By J. D. Flint

The geological conditions in the Vierfontein area ~re such that conventional pillar extraction ~stooping) cannot be practised safely or efficiently. Both the open-end lift and the pocket-and-fender methods of pillar extraction have been tried with little success because of problems with roof control and ground stability. The main reasons for the difficulties are the coarse-grained sandstone roof, local weaknesses in the coal seam, and the rate at which the pillars were extracted. The mine has practised bord-and-pillar mining since it started production in 1952, and considerable reserves of coal are contained in the pillars. As an alternative to total pillar extraction, in which hand-loading methods were practised, a system of partial pillar extraction using mechanized-mining methods ~11"modified goaf-line support has been evolved. These remnant coal pillars (snooks) remaining after partial extraction ofthe pillar, together with the installation of 1,2 m" matpacks and a double line of fullcolumn resin roofbolts, ensure control of the edge of the area that has been mined out (goaf). Where roof conditions preclude the use of conventional pillar-extraction methods, this method holds promise as a safe and efficient alternative for the recovery of coal from pillars and for an increase in the volumetric extraction of the reserves within a mining panel.

Jan 1, 1984

By P. M. Swash

A mineralogical investigation of the main causes of refractoriness of some metalurgicaly complex gold ores in South Africa is reported. It is shown that this refractoriness is related to the presence of submicroscopic gold, carbonaceous material, pyrhotite, and base-metal sulphides. Gold ores can be classified according to their content of these components. Electron-microprobe analysis shows that gold occurs in arsenopyrite and pyrite, the gold contents of which can be up to 2700 gft. The gold and arsenic contents of these minerals are closely corelated. Furthermore, within zoned arsenopyrite grains, the concentration of gold closely folows that of arsenic. Mossbauer spectroscopy caried out on samples of concentrate from the Barberton area indicates that the submicroscopic gold within the sulphides is in a non-metalic form. The mineralogical examination of beneficiation products is important, since it sheds light on some fundamental aspects of the behaviour of the ore and gangue components during milling and flotation. Such basic information will lead ultimately to a better understanding of the problems in the beneficiation of these ores. Investigations have shown that the overmiling of the auriferous arsenopyrite and the disseminated nature of the sulphide mineralization are the main problems during beneficiation.

Jan 1, 1988

The structural design of a pavement relates to the ability of the road to carry the imposed loads without the need for excessive maintenance or rehabilitation. Current techniques for the structural design of haulage roads are empirical and based primarily on the previous experience of personnel assigned to pavement design, both in terms of the strength of the structure and the quality of the wearing course material. This has the potential for unwarranted expenditure on too thick a structure or, conversely, premature deformation leading to the need for excessive expenditure on maintenance. Furthermore, the effect of larger haulage vehicles on the structural performance of a pavement cannot be predicted. Thus, there is a need to develop a portable and practical method of structural design. This paper presents an overview of structural design methods for mine haulage roads and, through an analysis and quantification of the structural performance of existing pavements, recommends the mechanistic design procedure, together with a revised structural design and associated limiting design criteria. It is concluded that the application of the mechanistic method to a design project can reduce the costs of haulage roads construction and accrue additional benefit in terms of reduced operating and maintenance costs.

Jan 1, 1996

By S. J. Patchet

The use of fill in deep-level gold mining presents the possibility of achieving considerable economic and operational benefits if conventional support can be eliminated. Unfortunately, the combination of the properties of tailings from gold reduction plants and the narrow, flat, tabular reefs being exploited make conventional hydraulic filling very unpractical. Laboratory tests indicate that, with careful control of water content, these tailings can provide an adequate fill material. A variety of bonding agents have been investigated, and the most practical seems to be ordinary Portland cement. Even at very low cement contents some cohesion is achieved. The design and layout for a complete fill support system using hydraulic transport, dewatering, and pneumatic placement are discussed, and a surface field trial indicated that the principles involved are correct and that acceptable results can be achieved. This system and material would completely eliminate conventional timber and brick support, and a preliminary economic analysis indicates that filling is cost competitive on a direct replacement basis. All the operations for a full-scale operation are available or have been developed to a stage sufficient to indicate that the system is practical, although certain operations require further refinement.

Jan 1, 1978

The results of small-scale resin-in-pulp pilot-plant investigations at Grootvlei Proprietary Mines Ltd, President Brand Gold Mining Co. Ltd, and Western Areas Gold Mine Co. Ltd are reported. At each mine, a pulp was fed simultaneously to a carbon-in-pulp plant, allowing a direct comparison of the metallurgical performance of the two processes. With the Grootvlei pulp, gold was extracted more efficiently by resin than by carbon owing to the Iow concentration of competing base-metal cyanide complexes in solution. With the Western Areas pulp, the reverse was true because of the high concentrations of copper and nickel in solution. Finally, with the President Brand pulp, resin-inpulp was significantly superior to carbon-in-pulp owing mainly to the inherently slow rate of gold extraction from calcine by activated carbon. Results are presented that show the efficiency of the elution of gold and other elements with a variety of reagents from the loaded resins arising from these three campaigns. At Western Areas, a detailed investigation enabled a preliminary cost evaluation to be made of three techniques for the elution of strong-base resins.

Jan 1, 1984

By B. G. Meyburgh

SYNOPSIS As a result of a test programme over a period of approximately ten years and a decision to extend the uranium plant, it was decided to design and erect the first full-scale Purlex Plant in the Republic of South Africa. The plant at Buffelsfontein G.M. Co. Ltd. was commissioned in August, 1968, and to date has produced results superior to those predicted in the original estimates. The capital expenditure was R678 000 for a plant capable of treating 1 600 gallons per minute of pregnant solution. Compared with the conventional resin ion exchange process, it has been found that the saving in production costs is 21 cents per pound U3O8 produced. The amine loss is 10 parts per million, which is equivalent to a total organic loss of 250 parts per million. The uranium loss in the raffinate is less than 0.001 g/l U3O8. The final product is of a high quality and it is probable that it is pure enough to convert to the fluoride directly.

By H. M. Dus, D. J. Smith

Resistivity tests indicated that, at temperatures lower than 1450°C, reducing agents alone, as well as burdens consisting of high-carbon ferrochromium and reducing agents, exhibit wide differences in resistivity. These differences are less pronounced at elevated temperatures. The resistivity of a reducing agent and the volume fraction it occupies are important factors controlling the resistivity of burdens of high-carbon ferrochromium. A mathematical model is formulated to describe the dependence of the resistivity of mixtures of conducting and insulating particles on the particle sizes and the volume fraction occupied by the conducting phase. The resistivity of burdens of high-carbon ferrochromium is high if the particle size of the reducing agent is larger than that of the other components of the burden. A number of reducing agents showed small variations in their reactivity towards chromite ore in the solid state. However, with chromite ore in the liquid state, reduction proceeded more rapidly with reducing agents occupying larger volume fractions. During the smelting of manganese ore, high initial rates of reduction were observed for reducing agents that had a high reactivity towards carbon dioxide and a high content of volatile matter, and that occupied a large volume fraction. High liq'uid-state reactivities were observed for reducing agents occupying a large volume fraction and having a Iow degree of graphitization.

Jan 1, 1980

By P. J. Lloyd

Society is fully justified in its concern about the environment, but that concern may, at present, be too uncritical It is, for instance, essential to establish that there is a valid environmental impact, and that there is truly a causal link between a human activity and an observed shift in environmental conditions. In establishing these, it inessential to recognize that scientific proof offers consistency, but that it can never provide completeness. Thus, no amount of scientific endeavour can ever prove that mitigation of the effects of human activity will be perfect. Society normally expresses its concern through legislation. The existing legislation in South Africa is reviewed, and it is found that [>legislation regarding water is probably too stringent to be effective, >legislation regarding air and land use is probably too lax, >all the environmental legislation is too fragmented to be efficient, and the Department of Environmental Affairs is hamstrung by inter-departmental rivalry. ] It is accordingly concluded that, if means are to be found for ensuring adequate mitigation of environmental impact in the face of ongoing economic development, it is necessary to establish a Judicial Commission on Environmental Affairs advised by, but given greater powers than, the departments currently active in environmental maters. This Commission should be charged with creating, perhaps over a decade, a body of legislation that would guide development while protecting the environment in its widest sense.

Jan 1, 1994

There are presently no suitable underground mine production scheduling optimisation models available for application to sublevel stope mining. Scheduling underground production for maximum return is therefore still a manual process, which generally involves scheduling production from the next available highest cash flow stope within the operational constraints of the project. In most mining operations, the scheduling problem is too large and complex to guarantee truly optimal results through manual scheduling. This paper reviews some general optimisation studies that have been proposed for underground hard rock mining. Furthermore, an example of a mixed integer programming model is presented for a small conceptual sublevel stoping operation. Comparative results of a schedule generated by a mixed integer programming (MIP) production scheduling model and a manually generated model on a nine stope example is presented. Results indicate that the potential benefits of the MIP production scheduling model for the purpose of maximising NPV are significant. Finally, a new constraint was formulated to limit multiple exposures of fill masses for use in an existing MIP production scheduling model. Testing of the formulation took place on the central stope of the nine stope example, which showed that the formulation performed its task without breaking other operational constraints.

Jan 1, 2007

By A. O. Filmer

The techniques used in this study of the non-oxidative dissolution rates of high- and Iow-grade nickel mattes in hydrochloric acid involved leaching and the use of a rotating ring-disc electrode. It was found that the rate of metal dissolution depends on the potential at which the matte dissolves, a maximum rate of dissolution being observed at -0,2 V to 0,3 V (relative to a saturated calomel electrode). The results are comparable with those obtained in work on the dissolution of synthetic nickel and iron sulphides. The adverse effect of excess sulphur on the rate of nonoxidative dissolution is explained in terms of the mixed potential of the reaction. The leaching studies showed the feasibility of processing a high-grade nickel matte by non-oxidative dissolution, and indicate that maximum rates can be obtained in the presence of fairly Iow concentrations of oxidant. A relative selective dissolution of iron can be obtained from the Iow-grade matte under reducing conditions, thus resulting in a significant upgrading of this material. Letter to the Editor Dravo Corporation is seeking information concerning a special method of transporting explosives to aid in designing a large underground oil shale mine in the mountains of Colorado.

Jan 1, 1981

By D. M. Meyer, K. Auerswald

The production of electrolytic manganese in South Africa by M. HARRIS, Pr. Eng., B.Se. (Eng.) (Fellow), D. M. MEYER, Pr. Eng., B.Se. (Meeh. Eng.) (Visitor), and K. AUERSWALD (Visitor) The decision to construct the first electrolytic manganese plant in South Africa was important and farreaching. After evaluating the results of the pilot plant operation, the first South African producer, Electrolytic Metal Corporation (Emcor), established a plant in Krugersdorp. Initially, there were many process problems that had to be InvestIgated, and, after these had been solved and many operating parameters had been established, manganese was successfully produced. When the Delta Manganese plant in Nelspruit was planned, cognizance was taken of the fact that, if peak efficiencies were to be maintained, the process must be operated between fairly narrow parameters. Instrumentation was therefore installed to control the process automatically wherever possible. The main features of the Delta Manganese operation are outlined, with a brief description of each stage of the process from ore milling through to electrowinning and packing of the metal. It is concluded that much benefit can be obtained from further research work into process improvements and into the exact effect of certain variables on plant and current efficiency.

Jan 2, 1977

By R. P. King

The flotation behaviour of phoscorite from the Phosphate Development Corporation was measured in a pilot plant, the flotation cells in the plant being varied in configuration so as to operate with or without circulating loads. The ore was floated in a batch cell so that the parameters for a kinetic model could be estimated, and these parameters were then used in a flotation-plant simulator, which is based on the kinetic model, in the prediction of the performance of a pilot flotation plant operating on phoscorite. The simulator predictions compare well with the measured performance of the ore in the pilot plant, but the comparison shows that the kinetic model is not completely adequate for the prediction of performance in continuous flotation plants. The model is weakest in its ability to model the behaviour of the froth phase. The flotation behaviour of the ore could be adequately described when it was assumed that the apatite and gangue each consist of floatable and unfloatable components. The effect of particle size on the specific flotation-rate constant of apatite was found to have a maximum at 85 µm and to fall to zero at 400 µm that for the gangue had a maximum at 50 µm and was zero at 350 µm.

Jan 1, 1978

By L. R. Nelson

The efficiency and cost-effectiveness of the aluminothermic reduction process in the production of ferro-alloys and 'pure' metals depends strongly on appropriate balancing of the process energy required. Insufficient energy results in a poor metal yield, while over-supply can result in excessive fuming and possibly even ejection of the reactor contents in a potentially dangerous 'thermite bomb' reaction. This situation becomes even more critical when the suitability of limited quantities of oxide from new sources must be evaluated, dictating smaller-scale testwork. The resulting higher relative heat losses from the system complicates control of the energy balance, and usually requires the addition of thermal boosters or reactant preheating in order to sustain an autothermic process. This often detracts from the quality of the metal product, and adds to the hazards of batch aluminothermic- reduction testing. The development of a small-scale method (producing less than 2,5 kg of metal) for the plasma-assisted aluminothermic reduction of chromium oxide that overcomes such difficulties is described. The technique involves the use of a sealed 50 kVA plasma-arc furnace to provide controlled electrical ignition and supplementary energy to the reactants contained in a water-cooled copper crucible. The application of the method to the evaluation of the aluminothermic production of pure chromium metal from a unique chromic oxide source is reported.

Jan 1, 1996

It is suggested that an increase in the production from thin coal seams in South Africa is necessary, and that a substantial amount of any increase will be mined by the bord-and-pillar method. For the purpose of this study, a thin coal seam was regarded as any seam 1,5 m thick or less to the minimum thickness at which mechanized equipment can operate in bord-and-pillar workings. The equipment being utilized in thin-seam bord-and-pillar layouts includes conventional equipment, load-hauldump cars (scoops), and drum-type and Fairchild-Wilcox continuous miners. Comparisons are made of these types of equipment for bord-and-pillar mining at various seam thicknesses within the thin-seam range. The evaluations involved production rates and the cost of extraction for South African conditions, use being made of an existing computer modelling technique in the generation of production rates. The indications are that, for seam thicknesses greater than 0,9 m, drum-type continuous miners utilizing continuous haulage are the most productive and cost-effective equipment at present operating in thin-seam bord-and- pillar workings. Where seams thinner than 0,9 m are to be exploited, Fairchild-Wilcox continuous miners, particularly the Mark 22, produce the most coal at the lowest cost.

Jan 1, 1984

By K. Hodgson, J. P. M. Hojem, N. G. W. Cook

Already about one-third of South Africa's coal is mined at depths exceeding 100 metres. Almost all this mining is done by the bord and pillar method. Conventional design procedures call for ever larger pillars as depths of workings increase, resulting in the loss of large amounts of coal and reductions in productivity. Barrier pillars are in general use to ensure against large collapses. The presence of these strong pillars would allow a more efficient design of the bord and pillar layout to yield improved extraction ratios by using smaller, yielding, pillars between the bords. Knowledge of the complete load- displacement curves for such pillars is a prerequisite for the design of such a system. A 100-MN, stiff jacking system for measuring the complete load-displacement curves of pillars with cross-sections of up to 2 m X 2 m is described. The jacks are installed in a slot cut across the central plane of symmetry of a pillar, thereby ensuring that the stress distribution in the pillar during a test, especially at its contacts with the roof and floor, is identical to that caused in a similar pillar by convergence across the seam. Preliminary results in the form of complete load-displacement curves for test pillars of about 1.5 metre square section are given.

By T. R. Twiddle

The sequential flotation of copper, lead, and zinc in that order is practised at the Broken Hill Concentrator of the Black Mountain Mineral Development Company (Pty) Limited. The minerals of economic importance are chalcopyrite, galena, and sphalerite, with associated silver. The targets for recovery and grade in the lead and zinc circuits were reached quite readily after start-up, but the copper circuit failed to meet the performance requirements with respect to both recovery' and grade. The original circuit for copper is described, together with the subsequent investigations and modifications that were required to produce acceptable metallurgical results. Circuits for semi-bulk and bulk flotation were tried, and the effect of the oxidation state of the pulp was investigated extensively and found to be all important. Tests were conducted on the depression of lead in the cleaning circuit by the use of sodium dichromate, and on heating with the addition of sulphurous acid. The latter technique was ultimately the more successful. The proportion of fresh to recycle water entering the circuit was shown to be important. The original reagent regime was altered and augmented. A more recent problem has been the contamination of the ore with cemented backfill. The changes that this new condition necessitated are described. Success has been measured by a continuous improvement in the economics of the copper recovery.

Jan 1, 1984

By P. R. Labrum, H. A. D. Kirsten

The literature on shotcrete is reviewed with the object of identifying aspects that have not been addressed specifically in terms of its structural performance and manufacture as applied to underground mines. The programme and results of a series of full-scale tests on mesh- and fibre-reinforced shotcrete panels are presented, from which it is concluded that fibre-reinforced shotcrete is competent, especialy at large deformations, and is equivalent in structural performance to mesh-reinforced shotcrete for a fibre content of 3 per cent by mass: furthermore, that the support design systems developed for mesh-reinforced shotcrete are directly applicable to fibre-reinforced shotcrete. The Q-NATM system for the design of temporary tunnel support is presented briefly as one such system. It provides for the integrity of the excavation to be considered in terms of its competence and displacement determinateness, and represents the first systematic procedure for the design of temporary tunnel support. Finally, the support designed on the basis of the Q-NATM system for the main and cross-cut tunnels on the production level in the proposed BA5 block cave at Premier Mine is presented as a practical example of the design of fibre-reinforced shotcrete as part of an overall support system.

Jan 1, 1990

By S. Budavari

The effects of shaft pillars left in deep-level hard-rock mines during the extraction of tabular deposits were studied some time ago, resulting in the formulation of design principles and procedures, which have been used with success in the design of shaft pillars in the deep-level gold mines of South Africa. The method has not yet been utilized in the design of shaft pillars in shallow and moderately deep hard-rock mines. The purpose of the present study was to remedy the situation since a great number of deposits are worked at those depths. The object of this paper is to present governing equations for the components of stress and differential movement as derived by use of an elastic model. The pillar is taken to be circular in the plane of a horizontal deposit. On the basis of the numerical results obtained, a study was made of the distribution of the vertical strain and tilt along the axis of the shaft, and of the vertical stress along the shaft and across the pillar. In every case investigated, the most adverse geometry was taken into consideration. By use of an empirical criterion and the results of some in situ observations, the determination of pillar dimensions and differential displacement components for South African gold-mining conditions is demonstrated. Pillar dimensions for shallow and moderate depths are compared with those accepted for deep-level conditions.

Jan 1, 1986

By A. Kijko, C. W. Funk

Methods for the analysis of seismic hazards in mines are reviewed as illustrations of the techniques that are being used in some South African mines. The classical parameters that describe a hazard are the seismic activity rate, ?, the Gutenberg-Richter value, b, and, occasionally, the maximum regional magnitude, mmax The activity rate is calculated readily owing to the inherent simplicity of its definition. The evaluation method presented for the Gutenberg-Richter b value takes into account the presence of mmax Three statistical procedures are described for the assessment of mmax which the maximum observed magnitude, Xmax a crucial role. Often, the configuration of mine seismic networks is changed, or the networks are improved, which inevitably gives rise to changes in the completeness of the seismic catalogues. The routine analysis of seismic hazards must account for these time dependent changes. A method for the evaluation of hazards is reviewed that accommodates varying levels of quality in the catalogues. Finally, the concept of the volume of ground motion (VGM) is presented. This is a technique that allows for most aspects of seismic hazards in mines. The advantage of the VGM is that a hazard can be described by one physically significant value: the volume of rock (cumulated over a time period) in which the ground motion exceeds some critical particle velocity. Data from the gold mining region in South Africa known as the Far West Rand is used in a demonstration of the discussed methods of hazard analysis.

Jan 1, 1994