Search Documents

By L. A. Abichequer

ROM grade variability is one of the most important factors influencing plant product recovery. Due to the influence of grade variability on mine profits, it is deemed important to guarantee a proper homogenization of the ore through a well-planned blending and homogenization pile system from which the ore is reclaimed at an acceptable grade fluctuation. This study tests geostatistical simulation efficiency in predicting in situ grade variability. The methodology is illustrated using a data-set from a large phosphate mine in central Brazil. Additionally, real data obtained at the mine site during January and February 2007 were used to derive the actual grades of each pile formed during this period. Each pile was formed by a selection of blocks within a dig line and these lines mined along the year 2007 were also made available. Given the real grades, it was possible to reconciliate and validate the results predicted by the proposed methodology. The main outcome of this study is the opportunity to check the geostatistical simulation as a tool to quantify the variability of the homogenization system.

Jan 1, 2009

By V. Matou?ek

The paper addresses pipe flows of aqueous medium-sand slurries at velocities lower than the deposition-limit velocity. Laboratory test results including measurements of particle concentration distributions are used in order to describe a flow with a (pseudo-) linear concentration gradient above a stationary bed. Particle dispersion within the flow is evaluated and a stratification-ratio equation is formulated, estimating a portion of contact load in the flow. The formula is incorporated in the proposed predictive model for the hydraulic gradient for a medium-sand flow above a stationary bed.

Jan 1, 2007

By B. Mulcahy, M. Valenta

"The purpose of executing a project in a stagewise fashion is to evaluate all potential options in a cost-effective manner and develop an understanding of the project drivers, thereby minimizing overall project risk to the client. Among the more valuable tools for this exercise are production and financial models that can be used to quantify the sensitivity of the project to the critical parameters.The mine and concentrator used in this case study are located on the Kalahari Copper Belt, which extends from Zambia through northern Botswana into Namibia. This area of Africa has seen very little industrial development and the project will create much-needed employment and development in the region.The success of this project thus far can be attributed to the close cooperation between the geological, mining, and metallurgical disciplines. Regular updates of projected capital and operating cost estimates coupled with project outputs guided the teams in optimizing their various discipline models, ultimately delivering a compelling argument for the execution of the project. Key to the success was the development of a geometallurgical model for the prediction of concentrate tonnage, grade, and recovery for the life of the mine from the mining plan.This paper summarizes the metallurgical findings and the outcome of the various project stages. The development of the model is discussed, as are the challenges faced in developing a suitable metallurgical process route. IntroductionThe Kalahari Copper BeltThe Kalahari Copperbelt, which extends from Zambia across northwest Botswana into Namibia, is considered to be a broad time equivalent of the Central African Copperbelt, with a similar style of mineralization. However, at shallower depths (<25 m), chrysocolla and malachite exist in significant proportions in certain geological areas. As illustrated in Figure 1, the project is located in the Ghanzi-Chobe Fold Belt which forms part of the Kalahari Copper Belt. The Ghanzi Group, which overlies the lowest stratigraphic unit (the Kwebe Formation), consists of three formations, namely the Ngwako Pan, the D’Kar, and the Mamuno Formation (Hall, 2012)."

Jan 1, 2016

By V. L. Nkuna, S. R. Amos, T. Naidoo

"Ivanhoe Mines’ Kamoa copper project is a recently discovered high-grade copper sulphide deposit in the Katanga Province of the Democratic Republic of Congo. The mineralization identified to date within the resource is typical of sedimentary-hosted stratiform copper deposits and comprises three distinct units: supergene, mixed, and hypogene mineralization. Since 2010, various metallurgical test work campaigns have been conducted on drill core from different areas within the deposit in line with resource expansion. The most recent bench-scale flotation test work has shown positive repeatable results. The work was conducted on a composite sample of drill core from the southern part of the Kamoa resource. The sample is representative of the first four to five years of planned production, when Ivanhoe Mines intends to produce clean, highgrade copper flotation concentrate. A detailed test work roadmap developed from first principles for the campaign led to an optimum flow sheet for treating the Kamoa mineralization. Copper recoveries of 88.3%, at a concentrate grade of 39.0% copper, were achieved using a composite sample — an improvement on the previously published 85.9% life-of-mine average copper recovery indicated in the November 2013 Kamoa Preliminary Economic Assessment. IntroductionThe Kamoa project is a newly discovered, very large, stratiform copper deposit with adjacent prospective exploration areas within the Central African Copperbelt, approximately 25 km west of the town of Kolwezi in the Democratic Republic of the Congo (DRC) and about 270 kilometres west of the provincial capital of Lubumbashi. Ivanhoe Mines holds its 95% interest in the Kamoa copper project through a subsidiary company, Kamoa Copper SA Limited SPRL, and DRC government owns 5%. The project location is indicated in Figure 1.In January 2013, a new independent mineral resource estimate ranked Kamoa as Africa's largest high-grade copper discovery and the world's largest undeveloped highgrade copper discovery. At this time, Ivanhoe Mines had estimated discovered Indicated Mineral Resources of 739 Mt grading 2.67% copper, containing 43.5 billion pounds of copper, and Inferred Mineral Resources of 227 Mt grading 1.96% copper, containing 9.8 billion pounds of copper, as demonstrated in the Preliminary Economic Assessment (PEA) (AMC, 2013). A 1% copper cut-off grade and a minimum vertical mining thickness of 3 m were applied in each classification."

Jan 1, 2016

By R. W. Ottermann, N. D. L. Burger, A. J. von Wielligh, P. R. de Wet, J. L. Steyn

Underwind and overwind protection system concepts for mine hoist shafts were developed in conjunction with and for the Safety in Mines Research Advisory Committee (SIMRAC). End-of-wind operation of mine hoists is the most hazardous aspect of mine hoisting, carrying the highest risk of loss of life, injuries to workers and loss of production. Systems operating mechanically and with local actuation were developed. This was done in order to remove the increased risk associated with dependency on remote or external energy and information supply associated with most existing protection systems. The proposed underwind protection system concept absorbs the energy of motion of a conveyance overrunning the design lower limit of travel by drawing a metal strip through a set of rollers. This action causes dynamic cyclic plastic bending of the strip material that converts the kinetic and potential energy of the conveyance into strain energy of the metal. In the concept design a pair of cable slings attached to the strips catch the overrunning conveyance and transfer the retardation force. The proposed overwind protection system concept absorbs the energy of motion of a conveyance overrunning the design upper limit of travel by early detaching of the conveyance from the hoist cable. This detaching is carried out via an additional humble hook activation mechanism fitted at a sufficient height below the spectacle plate to allow the conveyance to retard to standstill under gravity before it would crash into the spectacle plate. The conveyance so brought to rest is prevented from falling by means of jack catches on the conveyance interacting with a rack (toothed profile) fitted on the guide rails in the retardation zone. Scale models (1:10 scale) of both protection systems were designed for conformance with established retardation standards. The retardation standards were limited by the requirement of passenger safety in retarding cages. The models were then built and tested in a 1:10 scale shaft model. Retardation performance close to the required levels was achieved. The retardation distance required should allow such systems to be retrofitted to most existing shafts. Given the simplicity and robustness of the designs

Jan 1, 2003

By F. Smit

Mining and plant practices can benefit from preconcentration of UG2 platinum ores in a dense medium separation (DMS) plant. The main benefit of DMS is the selective discard of waste from the feed stream, thus improving project economics while reducing the power and water requirements for processing. On the mining side, with the correct combination of variables, implementing DMS as a pre-concentration step can reduce cut-off grades and, as a result, increase ore reserves. In addition, the use of DMS technology gives the mine team the opportunity to consider alternative mining methods for an operation. The challenges of balancing the mining tonnage, methods, and resulting grades with the process plant size, recoveries, and DMS discard volumes have resulted in the development of a model to optimize value on new projects or existing operations. This paper will focus on these benefits from a mining and plant perspective, quantifying the water and power savings, and look at the economic benefits of preconcentration and the effect of metal prices, plant feed grade, and DMS efficiency in different mining environments.

Jan 1, 2013

By T.R. Stacey

Physical testing of rock support for rockbursting conditions has been carried out for over 40 years. A review of this testing shows that it has been mostly component based, rather than actually testing support systems. Further, it is concluded that none of the testing is truly representative of rockburst loading in a similitude sense. Similitude conditions are not achievable, mainly because the real conditions in a rockburst event, such as seismic source location and magnitude, wave frequencies, amplitudes, and interactions, are not all known. Because such information is not available, and because the results of all testing carried out to date have not been able to define, for support design purposes, the capacity of support systems, ongoing physical testing of rockburst support systems is essential. It is essential that the test should simulate, or actually take place in, a supported rock excavation. A rock support system is a combination of individual support components that work together to retain and contain the rock. In doing this, the components are subjected to loading by the rock and to interactive loading between one component and another. It is necessary to prove the capacity of such rockburst support systems by subjecting them to severe loading, as in direct blasting. The direct blasting approach, pioneered more than 40 years ago, probably still provides the greatest validity as a significant test of rockburst support capabilities, even though it does not simulate a rockburst. Direct blast testing of rockburst support systems in a surface environment, such as in a quarry or on exposed rock cutting surfaces, could represent a practical development of the approach, facilitating the execution and monitoring of tests.

Jan 1, 2012

By G. Lyman

The cross-belt sampler is a device that is very widely used even though it has not been ratified by the Standards associations. This paper is concerned with the bias testing of two cross-belt sampler designs against stopped belt samples and a cross-stream cutter at the belt end. The bias analysis is carried out using size distribution as the analyte and conventional t-testing and the Hotelling T squared test, which are compared for their effectiveness. The paper considers the issue of detectable bias and the statistical planning of bias tests.

Jan 1, 2009

By A. Cambitsis

We show that the prioritization of business improvement and performance management decisions may be significantly improved by taking into account the systemic effects of changes made in a single process area. To do so we build a model of a mining value chain, taking into account consequential downtime that arises from downstream and upstream starvation and choking effects of each activity. Introducing the concept of internal capacity, this approach yields insight into the relative importance of key metrics such as loading and hauling rates. We suggest that a holistic view of this type should be a core component of business improvement and performance management decisions. Keywords value driver trees, production constraints, throughput analysis, capacity analysis, TOC (Theory of Constraints), activity interdependencies, unit cost reduction.

Oct 1, 2013

By Q. G. Reynolds

The dual-electrode direct current (DC) arc furnace uses two graphite electrodes, one connected as cathode and one as anode. Such an arrangement avoids some of the design difficulties associated with the anode hearth traditionally used in single-electrode and twin-cathode DC furnaces, but can introduce other design and operational difficulties including deflection of the arcs toward the furnace walls. Counter-intuitively, both arc jets in a dual-electrode furnace travel from the electrode down to the bath surface, despite carrying electric current in opposite directions?this is suggested in the theory of the governing equations of arc formation, and confirmed by experiments using high-speed photography. The dual-electrode arc system at small pilot-plant scale is studied using a transient magnetohydrodynamic model capable of predicting arc deflection and interaction from first principles, and the results are compared to the behaviour of twin-cathode systems at similar power. Finally, a simple arrangement of the furnace busbars, M configuration, is shown to provide some passive protection against arc deflection.

Jan 1, 2011

By A. Kapito

The ferrite-pearlite microstructure is the most popular microstructure for alloys used in structural applications, including railway wagon wheels. These alloys have been designed through alloying and thermo-mechanical processing to have a refined microstructure. Ferrite-pearlite alloys are low cost, weldable, have good fabricability, and are reliable under extreme conditions. Given these performance attributes, it seems unlikely then that their dominant position as structural steels would ever be challenged by alternative microstructures. One major achievement in the development of ferrite-pearlite steels has been in the refinement of their interlamellar spacing to very fine distances of the order of < 0.3 µm. A refined microstructure increases the hardness of the alloy, thus increasing its life under wear conditions. The interlamellar spacing in pearlitic steels has, however, been refined almost to its theoretical limit. The increasing demand for speed and increased axle loading on railway wagons requires the use of stronger, tougher, and more durable materials. This has opened the window for the development of novel bainitic steels. Bainitic alloys have a higher level of microstructural refinement than pearlitic ones. They have shown to have good wear resistance and rolling-contact fatigue resistance, and high toughness. This paper will discuss the progress to date on the development of bainitic railway wheel alloys. Four alloy chemistries have been chosen for possible further development.

Jan 1, 2012

By S. Shamaila

The design and efficient operation of density-based mineral processing units requires regular densimetric analysis to be carried out on the various associated process streams. The results obtained from such analyses can have wide application, including the generation of washability and partition curves, which are critical for process design, control, and simulation. This paper describes some of the collaborative efforts that Kumba Iron Ore, in partnership with Springer New Technology and Anglo Technical Solutions Research, is pursuing in developing a novel density determination technique exploiting X-ray transmission (XRT) and optical imaging. This technique is being developed with the aim to determine sample density distributions that apply to washability characterisation of ores. This technique is aimed to be an alternative to the traditional sink and float method. For certain applications sink and float has required the use of tetrabromoethane (TBE) solution?a chemical that has been classified as harmful and environmentally unfriendly. This paper therefore presents some achievements in developing this novel technique which seems to be very promising.

Jan 1, 2012

By J. A. L. Napier

The evaluation of stress distributions and deformations in the vicinity of tabular mine layouts has been carried out routinely for many years using the displacement discontinuity boundary element method (DDM). In this approach, mine layouts are approximated as irregular shaped planar cracks (or slits) where the ?width? of the crack, corresponding to the excavation height, is assumed to be negligible compared to the in-plane, lateral dimensions. Early implementations of this approach have employed square element tessellations with constant displacement discontinuity component values. This is generally restrictive when considering the analysis of irregular pillar layouts or the intersection of fault planes with excavations. This paper describes a general revision of this approach in which triangular or quadrilateral element shapes are introduced in conjunction with higher order variations of the displacement discontinuity shape functions. This facilitates an accurate evaluation of detailed stress and displacement components close to excavation surfaces and allows the investigation of local damage and failure behaviour associated with particular geological structures such as weak parting bands or weak layers. A method to embed these features in an efficient and accurate multi-level solution scheme is described. This formulation can be extended to allow the analysis of shallow-depth pillar layout problems, facilitating the assessment of the interactive response and stability of shallow depth pillar layouts. A simple deformation model is introduced to facilitate the assessment of pillar failure and bursting potential in shallow mine layouts. The computational techniques described here have been implemented in a computer code called TEXAN (Tabular EXcavation ANalyser) and are illustrated by the simulation of a particular multiple reef pillar mining problem in a shallow depth platinum mine.

Jan 1, 2007

By U. W. O. L Vogler

"The behaviour of rocks depends on their material properties, and therefore it is important that these properties are determined by relevant and reliable laboratory testing methods. The ISRM Suggested Methods are very important documents in this regard, and a draft suggested method exists for the determination of the ’complete stress-strain curve for intact rock in uniaxial compression’. The method specifies the required geometry of specimens and the required testing procedures. The research described in this paper involved the determination of complete stress-strain curves for two materials, one exhibiting the Class I characteristic, and the other the Class II characteristic. To obtain a better understanding of the deformation behaviours in the post-peak region, tests were carried out on specimens of both material types with different length-to-diameter ratios. The results showed that the geometries of the test specimens influence the stressstrain curves in the post-peak region. The implication is, therefore, that the numerical values obtained for the slopes of the post-peak graphs are not material constants, but are geometry-dependent. Explanations for this behaviour are given. These findings have important implications regarding the use of post-peak data, for example for blast fragmentation considerations, and for evaluation of rockbursting potential. The research findings are based on a limited amount of laboratory testing, and should be confirmed by further testing. IntroductionThe most common approach for studying the behaviour of rock is by compression testing of cylindrical specimens in the laboratory. Rocks respond to forces by deforming and eventually breaking. The strength and the deformation characteristics are derived from the stressstrain curves produced. Standard shapes and sizes for the test specimens and standard loading rates are recommended in the Suggested Methods of the International Society for Rock Mechanics (ISRM) and the American Society for Testing and Materials (ASTM) standards. In spite of these standards, there remain certain aspects of testing which require further attention. The research described in this paper deals with deformation and failure behaviour of rock materials using stiff, servocontrolled testing equipment. The particular objective was to test the premise that the behaviour of cylindrical rock specimens in the post-peak region of the stress-strain curves does not reflect only a material characteristic, but is influenced by the height-to-diameter ratio (the geometry) of the rock specimen. An additional objective was to investigate the effect of the stiffness of the test equipment on the outcomes of tests."

Jan 1, 2016

By M. E. C. Snyman, N. Naudé

"Coal fines produced during processing are difficult to dewater and result in a lower quality product and consequent lower value. A South African coal mine experiences severe difficulties with belt filter dewatering operations due to the presence of fines reporting from the thickener underflows. Plant 2 currently handles super-fine particles of size -34 µm and has low belt filter efficiency: excessive moisture retention lowers the product quality and strains downstream processing. It was necessary to determine an alternative method for dewatering these fines. Blending of fine material with coarser material was proposed as a solution. The effect of coal particle size and layering during ultrafines belt filter dewatering was evaluated using various blends of the fine Plant 2 material with coarser Plant 1 material. The best layering arrangement of the two materials and its optimum blend required to achieve reduced filter cake moisture content was determined in practise using a vacuum filter to simulate belt filtration. A blend of the two materials gave improved dewatering efficiency for the belt filters compared with that of the Plant 2 material alone. The best layering configuration was with Plant 2 material at the bottom and Plant 1 material on top. The optimum blend for industrial applications comprised 48% fines from Plant 2. IntroductionFines are produced during the processing of coal. It is estimated that 2 to 3% of run-ofmine coal reports to the ultrafine portion (-100 µm) (le Roux, 2005). The particle size of coal is inversely proportional to the amount of water adsorption, so smaller particles adsorb more moisture. Moisture removal requires either mechanical processes or thermal drying: mechanical processes are less expensive, but the fines still have high moisture retention. Discarding of fines leads to economic losses, so it is essential that they be dewatered so that they can then be sold as a product: fines need to be treated for both resource management and conservation reasons (Kenney, 1994). Removal of free surface moisture from ultrafine coal particles using a belt filter therefore remains a process that needs to be continuously improved. Ultrafine coal originating from a thickener underflow is known to be difficult to dewater owing to factors such as filter cloth blockage and moisture retention due to clogging. Mixing of finer and coarser materials has been proposed to deliver better dewatering efficiency and improved the quality of the recycled water (Kenney, 1994)."

Mar 1, 2019

By S. R. Xie, S. Gong, E. P. Li, S. S. He, Y. J. Sun, S. J. Li

"Based on the complicated geological production conditions and abnormal strata behavior of the fully mechanized caving face No. 102 in the Xinyang Coal Mine, we analyze the breaking and forming process of distinguishing key block structures in close spaced coal seams. This analysis establishes an integrated mechanical model of these distinguishing structures. Furthermore, the horizontal force TAB generated by downward key blocks A and B is quantified, as is the Pressure PG exerted by key block B on caved gangue. Finally, the interaction mechanism is revealed. Analysis of the results using Mathematica reveal the following: 1. Both TAB and PG exhibit approximately inverse relationships to coal pillar width b; 2. TAB exhibits an approximately exponential relationship with mining height M of which the base is greater than 1; 3. PG exhibits an approximately arctangent relationship with mining height M. Combining these results with field observations, we conclude that the area in the vicinity of supports 100#–120# in the upper area of working face No. 102 is the likely zone of abnormal strata behavior. Thus, this area was classified as a key control area. Based on these results, the graded support control technique is proposed. Application of this technique in the field resulted in a reduction in the rate of hydraulic support system malfunction from 47% to 7% in the key control area. In addition, during times of periodic mining pressure, the roof caving height value never exceeded 0.3 m and the maximum spalling depth never exceeded 0.2 m. Overall, the results indicate that this new technique has markedly increased the stability of surrounding support rock material. IntroductionClose-spaced coal seams are widely distributed in China, and mining proceeds from the uppermost to the lowermost seam (Zhang et al., 2008). In the case of coal seams in close proximity, a particular set of risk factors becomes pertinent. These include disturbance of lower seams during the mining of overlying ones and the decrease in mechanical stability of lower coal seams following repeated movement of key blocks in main coal seam roofs. This inevitably results in behaviour such as heavy wall spalling and support damage to fully mechanized caving faces in lower-lying coal seams, which necessitates a significantly increase in the measures to support surrounding rock material (Zhang et al., 2010; Huang et al., 2013; Xie et al., 2013)."

Jan 1, 2016

Many industries base their decisions on the assaying of tiny analytical sub-samples. The problem is that most of the time several sampling and sub-sampling stages are required before the laboratory provides its ultimate assays using advanced chemical and physical methods of analysis. As long as each sampling and sub-sampling stage is the object of due diligence using the Theory of Sampling it is likely that the integrity of the sought after information has not been altered and the generated database is still capable to fulfil its informative mission. Unfortunately, more often than not, unawareness of the basic properties of heterogeneous materials combined with the unawareness of stringent requirements listed in the theory of sampling, lead to the conclusion that massive discrepancies may be observed between the expensive outcome of a long chain of sampling and analytical custody, and reality. There are no areas that are more vulnerable to such misfortune than sampling and assaying for trace amounts of constituents of interest in the environment, in high purity materials, in precious metals exploration, food chain, chemicals and pharmaceutical products. Without the preventive suggestions of the theory of sampling serious difficulties may arise when making Gaussian approximations or even log-normal manipulations in the subsequent interpretations. A complementary understanding of Poisson processes injected in the theory of sampling may greatly help the practitioner understand structural sampling problems and prevent unfortunate mistakes from being repeated over and over until a crisis is reached. This paper presents an overview of the theoretical, practical and economic difficulties often vastly underestimated in the search for quantifying trace amounts of valuable or unwelcome components.

Jan 1, 2009

By S. C. Thorley, J. R. Menasce

Trackless mining in low profile (LP) and extra low profile (XLP) platinum stopes has forced equipment designers to re-evaluate their equipment profiles to match the undulating reef. Low profile equipment designed to work in conditions with smooth and flat floors will simply not function with undulating floors and roofs and will become wedged between the floor and roof, beached on undulations due to lack of ground clearance, or suffer excessive mechanical damage. Tyres, too, need special evaluation, as conventional tyres for trackless mining do not work in an extra low profile environment.

Jan 1, 2004

By B. P. Watson

The Bushveld platinum group metal deposits in South Africa are the largest in the world. These deposits occur as two distinct stratiform tabular ore bodies and strike for many hundreds of kilometres. Mining is extensive, with depths ranging from close-to-surface to 2300 m. The mining method is a variation of planar open stoping. Crush pillars are widely used to support the open stopes. These pillars are designed to fail and the residual strength provides the required support resistance to stabilize the stoping excavations. This paper describes the in situ measurement, of stress within a Merensky pillar from Impala Platinum. These measurements were used to derive a stress-strain curve that includes pre and post failure behaviour. 2D FLAC modelling, with strain softening, was done to investigate how damage expands into the hanging- and/or footwall. Although the so-called ?squat? effect is always present, the modelling suggests that it does not dominate the pillar system behaviour at larger width to height ratios. Punching of the pillar into the hanging- and/or footwall increasingly controls the pillar system behaviour with larger width to height ratios. The paper investigates the behaviour of a system that incorporates the immediate hanging- and footwall, as well as the pillar itself.

Jan 1, 2009

By T. Wallmach

Heavy mineral deposits are a source of the economic important element titanium, which is contained in minerals such as ilmenite, pseudorutile and rutile. In the Ranobe heavy minerals deposit these minerals occur not only as primary unaltered minerals but also display various degrees of alteration resulting in an increased titanium content of the deposit. The presence of the various FeTi-oxide minerals? textural relations is a reflection of geological processes and may ultimately be used to unravel the geological history of the deposit. These minerals have different chemical and physical properties that influence metallurgical tests and the quality of products produced from various mineral beneficiation streams. It is therefore of metallurgical importance that the minerals are well characterized, defined and monitored during preliminary beneficiation tests.

Jan 1, 2007