Search Documents

By P. G. H. Pistorius, D. S. Konadu, G. Lubbe

The aim of this investigation was to determine whether the composition of a shielded-metal arc-welding electrode coating affected the low-temperature impact toughness of austenitic stainless-steel weld metal. It is generally accepted that increases in the δ-ferrite and nitrogen contents result in a decrease in toughness at low temperatures. Weld metal from electrodes with a basic coating also generally exhibit better toughness than those from rutile (acidic) electrodes. An increase in basicity was expected to decrease the number and size of inclusions, which in turn provides a tougher weld metal. Three commonly available potassium–rutile E308L electrodes were used, complying with the E308L-16 and E308L-17 specifications. Analysis of the electrode coatings showed very similar chemistry and basicity. Significant differences in the inclusion contents of the weld metals were observed: the E308L-17 weld metal had a lower inclusion content (1.4% by volume) than the E308L-16 weld metal (3.7%). The former had higher impact toughness at all temperatures, despite a slightly higher nitrogen content. Regression analysis confirmed that the inclusion content had a significant effect on the impact toughness at all temperatures.

Jul 2, 2022

By H. J. Swanepoel, N. B. Strydom

Groups of up to twelve new recruits to the industry were subjected to climatic room acclimatization for either five, seven, eight or nine days prior to being tested for the degree to which they had been acclimatized. These tests were done at 32,2 0C (wet bulb) at a wind velocity of about 0,4 m/sec and the men worked for four hours at a rate of 215,6 kg m/min on one day and at a rate of 431,2 kg m/min on the second day. The results indicated that there is no significant difference between the degrees of acclimatization obtained by the eight- and nineday procedures which confirms the conculsions drawn in a previous report1. The eight-day procedure can thus be claimed to be perfectly adequate and safe. Decreasing the period of exposure to five or seven days would however, not be justified because of the significant differences in physiological responses that were observed on both test days between men acclimatized for these periods and those acclimatized for nine days. It is concluded that it would be unsafe to employ these shorter periods of acclimatization when underground environmental temperatures at which the men are to work, exceed 31 0C (wet bulb).

ERRATA-AUTHOR'S REPLY IN SEPTEMBER, 1970, JOURNAL: PAGE 52 I. Left half of the page, 4th paragraph, fifth line from the bottom: for 22 / 5 1/2 %, read 22 / 5 1/2 %. 2. Right half of the page, fifth paragraph from the bottom, third line from the bottom: for N(l - p), read N(1 - p)x. 3. Right half of the page, fourth paragraph from the bottom, second line: for: at time t after time zero, read: at time x after time zero. NOTICE TO ALL STUDENT MEMBERS OF THE SOUTH AFRICAN INSTITUTE OF MINING AND METALLURGY The Institute offers each year for competition among Student Members of the Institute a prize, or prizes, should entries so warrant it, of up to the value of R100 to be awarded to the Student Member or Members who submit the best paper or dissertation on a topic appropriate to the interests of the Institute. In the case of Student Members who are in full time study at a university the dissertation or thesis which they may have to write in part fulfilment of their university curriculum may be accepted provided it is presented in a manner and on a topic suitable for publication in the Journal. The closing date for the receipt of papers shall be 31st December each year.

By M. M. Makhofane

Anhydrous zirconium tetrafluoride can be used as a precursor for the manufacturing of nuclear-grade zirconium metal. This can be done by fluorinating plasma-dissociated zircon with ammonium bifluoride in a batch reactor. This paper describes the batch process. It was proved that anhydrous zirconium tetrafluoride can be manufactured by this route as confirmed by X-ray diffraction. The process shows potential for scaling up to the kilogram scale and possibly the tonnage scale.

Jan 1, 2012

By D. Lunt

This paper describes and sets in context the commercially proven uranium extraction processes. It also discusses some of the technologies that are currently being pursued with the aim of reducing costs and overcoming a number of technical issues that are faced by process designers and operators. In doing so, opportunities for the transfer of extraction technology from other industries/commodities are identified. The key processing areas that are examined include: ?The influence of mineralogy. The type of uranium mineralization and the nature of its association within a particular deposit will have a major impact on process route selection. Uranium minerals are classified according to their influence on extractive metallurgy. As the uranium price has risen in recent times, so opportunities are increasing for the recovery of uranium from less conventional resources such as phosphates and fossil fuels. ?The opportunities for employing techniques aimed at reducing the capital and operating costs of the overall process such as heap leach and beneficiation. Preconcentration by screening, gravity separation and radiometric sorting can potentially reduce the mass flow to the downstream leach and recovery plants. ?Purification or separation of uranium in carbonate systems. While it is possible to directly precipitate uranium from clarified leachate, the presence of impurities such as vanadium, molybdenum and others may dictate that ion exchange or selective precipitation is employed. Advances have been made in other industries in terms of improved ion exchange equipment aimed at reducing resin inventories and hence costs. ?Separation in acid leach systems. Earlier developments included the use of combined SX-IX systems (Eluex or Bufflex) and the introduction of continuous countercurrention exchange (CCIX). Column SX has found a ready application to uranium in view of the rapid extraction kinetics. With the renewed interest in uranium processing, efforts are being redirected towards further development of resin-in-pulp (RIP) as a means of driving down capital and operating costs. ?Extraction in a chloride environment. Australia and Namibia are desert countries where good quality water comes at a cost. However, both have access to saline water from either the ocean or subterranean aquifers. The issues associated with operating a uranium extraction operation in such environments is discussed. ?Extraction from less conventional sources. Recent price increases for U3O8 have resulted in a number of companies examining the recovery of uranium from sources such as fossil fuels and phosphate deposits. Both of these areas were examined in the 1970s and 1980s and a number of approaches were commercialized. The paper reviews the extraction options.

Jan 1, 2007

By G. E. Blight

Several aspects of the behaviour and properties of backfills consisting of cemented cyclone underflow tailings are illustrated by means of examples, and guidelines are given on the optimization of the performance of cemented fills. The stretch characteristics of the geofabric used to contain freshly placed backfill are described, as well as the relationship between these characteristics and the forces acting on retaining barricades. The properties required to achieve a self-supporting, stable free face in cemented backfill are explored, and a graphic relationship between stable height and shear strength is presented and compared with that for uncemented (classified) tailings. After a description of the characteristics of Witwatersrand quartzite gold-tailings backfill and commonly used cements, the process of drainage and air entry into backfill is outlined. Following this, the early-age gain in strength and the shear-strength characteristics, as well as the compressibility characteristics of cemented backfill, are described. Two phenomena that are potentially damaging to cemented backfill are seismic effects (or blasting acceleration) and the closure that takes place during the curing of cement. Investigations show that neither of these phenomena is actually significantly deleterious to gold-tailings backfill: liquefaction does not Occur as a result of seismicity, and hydration of cemented fill is not significantly impeded by closure.

Jan 1, 1996

By R. Thomas

A Honeywell TDC 2000 central process control system was installed at Rössing in 1984. The system controls the metallurgical operations from crushing to the finished product of uranium oxide and manufacture of sulphuric acid. The operation was previously controlled from nine separate local control rooms. The paper briefly reviews the design and commissioning of the control system on an operating plant and discusses the impact on manpower organisation and training needs. Development of the process control system during its first two years of operation is reviewed and a summary is given of the current status of computer control at Rössing. The impact of the new system on overall plant operation and performance efficiency is also briefly described. In conclusion, future developments of computer control and overall optimisation of metallurgical operations are reviewed.

Jan 1, 1987

By J. R. Dixon

Gold mining has been undertaken in South Africa for more than a century. A great proportion of that mining has been from the Witwatersrand Basin; a geological phenomenon that has few parallels throughout the world. It has produced some 47 000 tonnes of gold mainly from underground mines, many of which have been truly world class gold mines. The gold mines of the Witwatersrand Basin have dominated world gold production from their inception and their production has been one of the cornerstones of the development of South Africa as a whole. The mines have some very specific characteristics; their sheer size, the depth of extraction, the nature of the orebodies, and their labour-intensive methods. The mines have also been part of the Mining House concept-a concept unique to South Africa. South African production has declined from a maximum of 1000 tonnes in 1970 to 470 tonnes in 1997. This, as a percentage of western world production, has declined from a maximum of 79 per cent (in 1970) to 21 per cent of world production (in 1997). The nineties' have seen South Africa and its mining companies move onto the world stage and face the harsh realities of having to compete in all spheres of business with their aggressive counterparts principally in Australia, Canada and the USA. The fight is for investment funds with the owners looking for the best returns on their money. In his address Roger Dixon will examine the current situation in the gold mining industry and examine the competitiveness of the mines of the Witwatersrand Basin compared with their peers worldwide. He will also discuss some of the fundamental challenges facing South African gold mines in the areas of legislation, technology, industrial relations, and health and safety. The environment in which the mines operate has changed radically in recent years and their ability to respond to these challenges will determine their future existence.

Jan 1, 1998

By D. Krebs, Tero Korhonen, X. Yang, A. Kirpala, N. Heino

At present, over 85% of the world’s rare earth oxides are produced from the bastnäsite ores, found mainly in China. Meanwhile, the ion adsorption ores are the most important sources for heavy rare earth production. As the demand for rare earth materials in the world increases, other forms of rare earth deposits will become new potential resources of rare earth production in the future. In this paper, flotation performance of a steenstrupine ore from the Kvanefjeld deposit for rare earth recovery was studied through laboratory bench testwork. The effects of various factors including grinding size and collector dosage on recovery and selectivity of the selected rare earth elements, La, Ce and Y, were investigated. A rare earth concentrate with the grades of La 2.8 wt%, Ce 5.1 wt% and Y 1.0 wt% at recoveries of 80.5% La, 79.8% Ce and 55.3% Y was obtained in optimum conditions. Further potential to improve the efficiency of REE flotation was discussed. Keywords: Rare earth elements, flotation, steenstrupine, Kvanefjeld deposit

Jan 1, 2020

By A. J. S. Benade, N. B. Strydom, W. H. Van Der Walt

The influence of two weeks of microclimate cooling on the state of heat acclimatization by N. B. STRYDOM, M.Sc., Ph.D. (Illinois) (Fellow), A. J. S. BENADE, M.Sc. (Potch.) (Visitor), and W. H. VAN DER WALT, B.Sc. (Potch.) (Visitor) Five volunteer Black subjects were acclimatized according to the climatic-room acclimatization procedure, and their states of heat acclimatization were determined by the usual heat-stress test. The subjects thereafter wore pre-frozen jackets in a somewhat higher environmental temperature (33,9/35,6 °C). stepping at the same rate as before for four hours a day for fourteen days. The heat-stress test was repeated and followed by a similar test at the higher environmental temperature. It was found that fourteen days of microclimate cooling in a very hot environment had no adverse effect on the degree of heat acclimatization. The sweat rates during microclimate cooling remained high, even though no sweating is possible beneath the pre-frozen ice-jacket. which indicates that there is an increase in sweat rate from the areas of exposed skin.

Jan 7, 1975

By R. A. H. Lycett, P. R. Jochens, D. D. Howat

The crystallization of rutile from titaniferous slags by R. A. H. LYCETT, M.Se. (Eng.),"A.M.I.M.M. (Visitor), P. R. JOCHENS, Pr. Eng., M.Se. (Eng.) (Rand), Ph.D. (Member), and D. D. HOWAT, B.Se., Ph.D., F.R.I.C., F.I.M. (Fellow) Factors affecting the precipitation of rutile from smelter slags were investigated, with particular reference to the effect of additions of phosphorus pentoxide to the slag. The phases were identified and the phase boundaries determined for slags having phosphorus pentoxide additions of 0 to 50 per cent. The liquidus temperatures of these slags were determined, and a pseudo-binary phase diagram was constructed. Rutile crystallized as the primary phase from melts having a phosphorus pentoxide content of more than IS,S per cent. Prismatic rutile crystals whose TiO. content was more than 97 per cent were grown from melts that had a phosphorus pentoxide addition of 30 per cent. However, the morphology of the precipitated rutile was such as to make subsequent separation impracticable.

Jan 9, 1975

A 36-year-old A-S-H pump, manufactured to designs dating back to 1936, was recently presented to the Gold Mine Museum by Envirotech. The pump, a B-frame three-piece rubber-lined Hydroseal unit, was supplied by Envirotech's predecessor company, Denver Machinery, and was installed by South Roodepoort Main Reef Areas Limited on 22nd March, 1948. Metals, materials, manufacturing The 37th Annual Conference of the Australasian Institute of Metals will be held in Ballarat (Australia) from 13th to 17th May, 1985. 1985is the Sesquicentennial year of Victoria, and for the first time the historic City of Ballarat has been chosen as the venue for an Australasian Institute of Metals congress. Steel rolling Conferences on steel rolling, sponsored by The Iron and Steel Institute of Japan (ISH), and supported by iron and steel institutes in many countries of the world, have been held since 1980. The first conference was held in Tokyo in 1980, sponsored by The Iron and Steel Institute of Japan.

Jan 1, 1984

Corosion technology: An information source book, by Judith Ann Douvile. Taylor & Francis, 1989. 188 pp. £32. Stainless steel buyers guide 1990. Southern Africa Stainless Steel Development Association (P.O. Box 4479, Rivonia, 2128), 1990. Free. Fatigue and stress of engineering materials and structures, edited by H.P. Lieurade. ITT International (40 Promenade Marx-Dormoy, 93460 Gournay-sur- Marne, France), 368 pp. US$ 109. Titanium and aluminium, edited by P.A. Coulon. ITT International (40 Promenade Marx-Dormoy, 93460 Gournay-sur-Marne, France), 200 pp. US$ 80. Engineering applications of stochastic processes. Theory, problems and solutions, by A. Zayezdny, D. Wulich, and D. Tabak. Chichester, John Wiley, 1989. 525 pp. £54.50. Metal behaviour and surface engineering, edited by S. Curioni, B. Waterhouse, and D. Kirk. ITT International (40 Promenade Marx-Dormoy, 93460 Gournaysur- Marne, France), 413 pp. US$ 109. Fuzzy control and fuzzy systems, by W. Pedrycz. Chichester, John Wiley, 1989. 272 pp. £37.50. CILO (carbon-in-leach with oxygen) cost study, by Minproc Engineers (USA). Free.

Jan 1, 1990

1. Book review • World mineral statistics 1974 to 1978. Production: Exports: Imports. London, H.M.S.O., Institute of Geological Sciences, 1980. (Reviewer: R. P. King) This edition is the third in a regular series prepared by the Institute of Geological Sciences. It is a useful compilation of statistics on the production, export, and import of fifty-eight different mineral commodities. Each mineral is listed by country, and a table is provided for the annual production, the annual imports, and the annual exports for each commodity included. However, some commodities are treated in considerably more detail; for example, aluminium and bauxite have tables under the following headings: Production of Bauxite, Production of Alumina, Production of Primary Aluminium, Exports of Bauxite, Alumina and Aluminium, Imports of Bauxite, Alumina and Aluminium. The information presented is the latest official information available from primary sources; the compilers have not relied on data from secondary compilations. This publication will be of considerable assistance to all who are concerned with the trading of mineral commodities and their production.

Jan 1, 1981

Book Reviews M. J. Jones(ed.). Geological, mining and metallurgical sampling London, The Institution of Mining and Metallurgy, 1974. 268 pp. £8. Spooner, J., et al. (eds.). 1974 miningannual review, London, The Mining Journal Limited, June 1974. 506 pp. £14,25 (including annual subscription to Mining Journal and Mining Magazine). J. H. Quilliam et al. (eds.). The ventilation of South African ~old mines. Johannesburg, Mine Ventilation Society of South Africa, 1974. 488 pp. RI0,00. The Hans Merensky Foundation As announced in a recent brochure, the 25-year-old Hans Merensky Trust has been converted to The Hans Merensky Foundation, its main objective being 'to promote and assist in the development of the resources of the Republic of South Africa and neighbouring territories articularly such natural resources as soil, water, minerals, flora and fauna-and to promote the health and welfare of the inhabitants; more specifically by research, experiment and demonstration and through the correlation and application of scientific knowledge'. Applications for S.A.I.M.M. membership and transfer Please note that new application and transfer forms have been issued.

Jan 11, 1974

By RT White

For a number of years the steel tube and pipe industry has worked on resolving problems of product quality. These have largely been resolved and new products have been developed to take advantage of new developments. To fully coordinate market acceptance guidance on use of galvanized piping was also required. This was largely achieved locally in 2004 with the publication by the SABS of ARP 060 - Guidance on the use and application of hot dip galvanized steel piping for the transportation of potable water in South Africa. Use of this document is not easy however and a need to have a simple computer model to assist the specifier was identified. Working with a major tube and pipe manufacturer this is now being developed and this paper will provide the background to the model?s development and its intended use. There is still a need for a partner Code of Practice on the performance of galvanized piping in buried conditions and the need for this will be highlighted together with current available information.

Jan 1, 2006

By J. W. Wilson, P. C. Graham

Raise-boring experiences in the gold mines of the Anglo American Corporation Group by J. W. Wilson M.Sc., M.I.M.M., F.S.A.I.M.M., M.A.I.M.E. and P. C. Graham M.Sc. (Eng.) Gold mining is being carried out at ever-increasing depths in South Africa. For reasons of safety and human comfort, it is becoming imperative for raises to be developed by means other than conventional drilling and blasting. Raise-boring is an attractive alternative method. Initial raise-boring experiences in South African gold mines showed disappointingly high costs due to the abrasivity and difficulty of drilling Witwatersrand quartzites. Consequently, a research and development project was instigated with the objective of making raise-boring an economically viable technique in hard abrasive rock. A Robbins 61R raise-borer was made available to the Research and Development team and a number of raises have been drilled. During these trials two advances in cutter design were tested. This paper presents the results obtained, including drilling costs, and provides details of the equipment used.

By A. Holder

A major mud push occurred on the 870 m production level, scraper drift block cave at Dutoitspan diamond mine in November 2011, during which it is estimated that more than 4 400 m3 of mud engulfed the west cave. The production level was successfully evacuated during the mud push with no loss of life or injury to personnel, thanks largely to mine employees being well trained in and adhering to on-mine mud rush evacuation procedures. All access to the west cave was lost as a result of the mud push. Clean-up operations are currently under way to regain access to the production level, to establish the extent of damage to scraper drifts and equipment, and to evaluate what remedial works may be required to resume production. The magnitude of the Dutoitspan mud push necessitated a detailed investigation into the key contributing factors leading up to the incident, which are discussed in this paper. Mud rush mitigation measures in place on scraper drift block caving operations at Dutoitspan, Bultfontein, and Wesselton diamond mines in the Kimberley area are critically reviewed. Recommendations are furthermore made for enhanced mitigation based on mud rush risk profiles derived for different production areas in these old scraper drift block caves. Keywords mud push, mud rush, scraper drift, block cave, mitigation factors, risk profiles, risk management structure.

Jul 1, 2013

By A. P. Cook

Gas samples were taken from a wide range of target areas on dumps arising from coal mining activities. Some of the dumps had largely burned out, some were still burning, some were in the process of rehabilitation, and on others rehabilitation was essentially complete. It was found that rehabilitation was very effective in reducing emissions to tolerable levels. Even incomplete rehabilitation reduced the CO2 emissions to less than about 1 kg/m2/a, whereas some unrehabilitated areas showed emissions of over 100 kg/m2/a. Some areas where there was active combustion taking place were also sampled, and they showed as much as 7 000 kg/m2/a, but the areas concerned were very small and their total contribution accordingly low. Analyses were also made for SOx, NOx, NH3, and CH4, but these were generally (and unexpectedly) at very low levels. The mines sampled represented 53 per cent of all surface coal mining activity. Accordingly the estimated total emissions were scaled up, to arrive at estimates of 1950 000 ± 350 000 t/a C02, 2040 ± 580 t/a SOx, 306 ± 85t/a NOx, and 31 ± 9 t/a NH3 for all surface mines. Methane was detected only from burning coal, and due to the difficulty in sampling, no reliable estimate could be made of these methane emissions.

Jan 1, 2012

By J. L. Taylor, E. B. Viljoen, W. M. Craig, A. M. McIntosh

The Chemwes uranium plant treats old gold-plant residues from the Sttifontein and Buffelsfontein Gold Mines by acid leaching, belt filtration, countercurrent ion exchange (ClX), and Bufflex solvent extraction (SX). The uranium is recovered by precipitation as ammonium diuranate. Absorption and elution in the CIX section are achieved in four NIMCIX columns operating as two parallel streams. Each loading column is 4,85 m in diameter and contains 12 absorption stages. The elution columns are 3 m in diameter and contain 8 stages. The eluant used is 10 per cent sulphuric acid at ambient temperature. During the commissioning and initial operating periods reported here, the plant yielded an average barren solution of 1,6 p.p.m. of U3O8 from a feed with a mean U3O8 concentration of 132 p.p.m. The U3O8 concentrations in the barren solution were better than 2 p.p.m. some 85 per cent of the time, and better than I p.p.m.73 per cent of the time. Investigations are underway to institute an automatic control system that will result in the U3O8 values on the resin and in the barren solution being maintained at or near the target values in spite of changes in the concentration of uranium in the feed solution.

Jan 1, 1982