Search Documents

By X. Chen, F. An, H. Chen, Z. Wang

The bottom drainage roadway plays a crucial role in preventing coal and gas outbursts by using underground gas drainage methods. Therefore, it is essential to select the ideal position of the bottom drainage roadway. In this paper use a combination of geological data and numerical simulation to study the ideal position of the bottom drainage roadway, we taking the gas drainage of the first workface of No. 3 coal seam in the Yuxi coal mine in China as an example. The geological study showed a limestone marker layer at an average vertical distance of 14 m from the first mining face. Using this marker layer, the bottom drainage roadway could be excavated without the risk of accidentally exposing the coal seam, and less crosscutting borehole drilling from the bottom drainage roadway would be required. Based on the needs of gas control, the layout of the bottom drainage roadway was selected as an external stagger type. Combined with the numerical simulation results, when located 20 m outside of the mining workface ‘footprint’ on the horizontal projection, the bottom drainage roadway was a sufficient distance from the stress concentration area during mining of workface 1301, which facilitated roadway maintenance. Furthermore, the length of the crosscutting boreholes is also relatively short, which reduces the amount and cost of drilling. The results of this study are expected to provide a reference for the selection of an ideal position of the bottom drainage roadway in field engineering.

May 2, 2022

By S. Shi, X. Xia, F. Xuesai, Z. Shen, D. Han

The hydrodynamic characteristics of a mechanical flotation cell’s transportation zone have significant impact on its metallurgical performance, especially on coarse particles recovery efficiency. However, how to define and adjust the transportation zone was seldom investigated by researchers. In this paper a method will be introduced to define the boundary of the transportation zone by PIV measurement. It is found that the transportation zone can be extended upwards by enlarging the entire rotor-stator assembly from the bottom of tank and increasing the jet angle of the impeller. Two control methods have been validated in industry tests on KYF-160m3 and KYF-320m3 air-forced mechanical flotation cells. The result shows coarse particles recovery are both improved distinctly. It is suggested that enlarging the top transport boundary is able to helpful to reduce the floating distance of bubbleparticle aggregates, which contribute to improve coarse particle recovery in large flotation cells. Key Words: Flotation cell; Transportation zone; Coarse particles flotation

Jan 1, 2020

By M. Frenzel, K. Bachmann, M. Rudolph, R. Tolosana-Delgado, E. Schach, M. Buchmann, L. Pereiraa, K. G. van den Boogaart, N. Kupka

Geometallurgy - the science of predicting the behaviour of ores along the value chain based on their geological and mineralogical characteristics - has barely moved beyond process minerology studies. These studies typically link process behaviour to the mineralogical and microstructural characteristics of pristine or processed ores in a qualitative or semi-quantitative manner. Eventually, a trial-and-error optimisation of the operation is achieved. However, to deliver on its promise, geometallurgy should progress beyond this current approach to a fully quantitative understanding of process behaviour, including the various uncertainties involved, namely predictive geometallurgy. One of the barriers currently hindering this development is the neglect of most ore characterisation data obtained in geometallurgical studies. This is mostly due to the large extent of this information exceeding the capacity of conventional software. To address this challenge, we developed a data mining platform consisting of an SQL database, an R front-end in-house package, and back-ends to interpret data from several analytical instruments. This platform enables the use of the statistical and data mining power of the R open-source environment for any geometallurgical study. Potential applications range from ore characterisation to process understanding and forecasting, and from geostatistical prediction to operational control and optimisation. The scripting abilities of R allow for the: 1) processing of many streams in loops, thus freeing the user from repeating tedious click-and-drop tasks; 2) computation of virtually any derivate or aggregate quantity from the data; 3) distribution of the work among several processor clusters; and 4) keeping of a log file for the calculations done. This contribution presents the building blocks of this platform, and illustrates with several examples its potential to enable predictive geometallurgy. Keywords: Data mining, entropy, kernel methods, LASSO regression, predictive geometallurgy

Jan 1, 2020

By G. Akdogan, T. P. Kekana, Q. G. Reynolds

The DC arc plasma gasifier concept is currently under development at Mintek for testing the feasibility of producing syngas from waste coal fines and dry steam. The technology is intended for the valorisation of low-grade discard coals into market-quality syngas, which may then be used for largescale electrical power generation to address current grid supply challenges in South Africa. Other potential applications include feedstock for petro-chemical plants, fuel for transportation vehicles, domestic and industrial heating, and others. The proposed concept of a DC arc plasma gasifier was developed based on a plasma torch, metallurgical-based and entrained flow coal gasifiers. The principles of design and operation of the proposed gasifier are based on the concept of the Westinghouse Plasma Corporation (WPC) gasifier where the torches are substituted by graphite electrodes from which electric arc plasmas are generated. The DC section of the gasifier will be designed considering Mintek’s experience in the sealing of the furnace as carried out in the Mintek Thermal Magnesium Process. As part of the building blocks of a full conceptual design, the feasibility of the DC arc plasma gasifier was investigated through testing and modelling of its critical elements as proof of concept. The main activities of this work included pilot scale evaluation of the arc behaviour in the presence of dry steam, modelling of the temperature distribution within the reactor and explosibility studies on three different coal dust samples. Keywords: DC arc plasma gasifier, explosibility index, lower explosion limit, minimum ignition energy

Jan 1, 2020

By S. C. Maji, U. S. Chattopadyay, S. Chaudhuri, T. Gouri Charan

India is devoid of coking coal resources, which is a vital raw material for coke making. As a result it has to import about 80% coking coal for steel making. Indian National Steel Policy, 2017 has envisaged crude steel production around 300 million tonnes Mt) by the year 2030-31 and forecasts coking coal demand of 161 Mtpa (million tonnes per annum). One way of improving the indigenous resources is to study the performance of existing washeries and to improve the clean coal recovery by adopting suitable technology. A study was carried out, mainly to focus on the fine coal circuit of an existing coking coal washery, to generate the desired quality of clean coal. The operating coking coal washery being studied is presently feeding coal from nine different sources with varying feed ash contents. The coal fines varied in ash content ranging from 19.5% - 43.6%. For treating the coal fines, the washery has operated a spiral for the past few years. Performance studies were carried out, and it was found that the spiral is not efficient in recovering the cleans. Detailed investigations were carried out on the coal fines using flotation techniques, and it was found that to achieve a low ash clean coal, the froth flotation is a much better beneficiation option than a spiral, The studies showed that the recovery of clean coal through a spiral is 67.7% at ash content of 27.0%, while flotation tests showed a recovery of 68.1% at 16.5% ash content. Keywords: Coking coal washery, near gravity material, spiral washer, froth flotation

Jan 1, 2020

By F. Dutoy, M. B. Stella, C. F. Carrozza

Rare earth elements (REEs) are indispensable components in the manufacturing of high-tech devices, renewable energy technologies, and defence applications. As global demand for these elements continues to rise, there is a pressing need to optimize extraction processes for both efficiency and environmental sustainability. This study explores approaches to rare earth extraction using Ionquest® 801 and integrates a predictive modelling to enhance process understanding and optimization. We conducted a screening test varying pH process to evaluate the best extraction efficiency. Starting pregnant leach solution (PLS), solution was prepared in the lab with the following rare earth elements: La, Ce, Gd, Dy, and Υ, at 0.02 M for each element. The data obtained were used to develop empirical and mechanistic models to predict rare earth extraction yields and flowsheet. Further tests were performed by mixing specific concentrations of different extractant and/or phase modifier. Our experimental results demonstrated the effectiveness of the proposedextraction methods, highlighting improvements in both yield and selectivity. The developedmodels successfully captured the complex relationships between process parameters and extraction efficiency, providing valuable insights for process optimization.

Nov 6, 2024

By B. O. Odera

The Pt-based alloys have a high potential for replacing some Ni-based superalloys (NBSAs) used in the highest temperature and most aggressive environments, and vanadium would be a beneficial alloying element. Six alloys of average compositions Pt-26.6Al-9.1V, Pt-23.1Al-17.8V, Pt-9.6Al-21.1V, Pt-17.4Al-6.4V, Pt-22.3Al-7.9V, and Pt-6.0Al-10.1V (all in at.%) were manufactured by arc-melting and examined in the as-cast condition using scanning electron microscopy and X-ray diffraction (XRD). Five samples were heat treated at 1 000°C for 1 500 hours and water quenched, then examined. The phases were identified using energy-dispersive X-ray spectroscopy and the identities were confirmed by XRD. In most of the samples, the phases existing in the as-cast condition were different from those at 1 000°C after ~1500 hours heat treatment. A solidification projection, an isothermal section and a liquidus surface projection were determined for the Pt-rich corner.

Jan 1, 2012

By B. Ceki, A. Mabentsela

The BCL furnace is scheduled to restart operations after being placed on care and maintenance in 2016 due to depressed nickel prices. The decision to start operations after such a stoppage ought to be led by a techno-economic evaluation of process options to make operations more resilient. For BCL, the decision lies between using the existing flash-smelting furnace (FSF) or a top-submerged lance (TSL) furnace. Available studies show that the FSF combined with other converting technologies is cheaper to operate; however, such studies are based on flowsheet simulation results of single copper concentrates and therefore do not provide a full scope of practical capabilities based on smelter operator skills. Using a t-test on normalized prior operational data from three Cu FSF and two Cu TSL, it was found that the only statistical differences between the operating costs of the FSF and TSL technologies are in the coal use for heating the feed blow and number of rebuilds: the FSF consumes coal to heat the feed blow and the TSL requires 2.4 rebuilds during a course of a single FSF campaign. A summative operating cost comparison over the existing BCL FSF 11-year life shows that BCL can decrease operational costs by some BWP 55.5 million if the operation were to change to the newer TSL technology. The savings derive from reduced coal use, which is normally associated with heating the blow when using the FSF. Despite the TSL carrying added costs of 2.4 rebuilds during a life time of one FSF furnace campaign, the cost associated with the TSL rebuilds of approximately BWP 1.3 million is minimal compared with the overall operational expenditure decrease that BCL will incur on using the TSL technology. In terms of the technology, BCL can have higher Ni–Cu recoveries at lower operational costs by elimination of Ni–Cu losses and eliminating the slag-cleaning furnace by converting to a TSL furnace.

Jul 10, 2024

By C. M. Rule, A. K. Anyimadu, L. Knopjes

Ongoing development work on ultra-fine grinding for various applications at the Group?s concentrators has been conducted by Anglo Platinum over the last few years. Current potential applications for mainstream grinding and concentrate grinding are the subject of a group-wide research and development programme. The first 10 000-litre 2.6 MW IsaMill was jointly developed by Anglo Platinum, Xstrata Technology and Netszch for installation at the Western Limb Tailings Re-treatment project in Rustenburg, South Africa. The unit was commissioned in late 2003/early 2004, and has operated in an intermediate concentrate regrind application successfully since. This paper describes the operational performance to date, as compared with the original duty specifications and objectives. The first mainstream M10 000 IsaMill with a 3 MW drive will be operational in November2006 at the Potgietersrus Platinum (PPL) ?Platreef? Sandsloot Concentrator in South Africa?s Limpopo Province. Key Words: Western Limb Tailings Re-treatment Plant, IsaMilling, Platreef, Platinum, Palladium, PGMs, tailings.

Jan 1, 2006

By J. O. Mogalanyane, N. Naudé, A. M. Garbers-Craig

The fines produced is not suitable as feed material for the subsequent rotary kiln and the electrical arc furnace. The need for briquetting the ferronickel ore is premised on the minimisation of fine particles in the rotary kiln as well as improving charge permeability in the furnace, and improving overall process safety. Briquetting may be defined as an agglomeration method in which fine particles are compressed under pressure. It consists of three different technologies: vibropressing, roller pressing and stiff extrusion. The current study focuses on evaluating the performance of ferronickel briquettes generated, using roller-pressing technology. Physical properties, chemical properties and metallurgical properties of the briquettes were used to evaluate their performance and quality. Standard ISO tests for iron ore pellets were used. Size degradation as a result of reduction was measured using the ISO 4696-1 test. The decrepitation of the briquettes at the point of entry into the rotary kiln was evaluated using the ISO 8371 test method at a temperature of 700oC. The degree of reduction was evaluated using the ISO 4695 test procedure. Average green briquette compressive strength of 559 N was reported at a moisture content of 16% with an average drop number of 19.1. Increasing the moisture content has a detrimental effect on both the compressive strength and the green briquette yield. The drop number is expressed as the number of drops until breakage, when a briquette is dropped from a 1 m height, decreased with an increase in moisture content. At a moisture content of 16% an average green briquette yield of 85.1% was reported. Keywords: Ferronickel briquettes, moisture content, curing conditions, physical properties, chemical properties

Jan 1, 2020

By J. Arzuúa, U. Castro-Filgueira, L. R. Alejano, F. Malan

"Pillar design for underground mining is typically done using empirical formulae or numerical modelling. Practical experience and recent literature, nevertheless, illustrate the shortcomings of these design approaches. Ongoing monitoring of pillars is therefore recommended to minimize the risk associated with these designs.In a mine where a large number of pillars are cut, different pillar strengths can be expected owing to variations in rock mass strength from area to area. This problem is compounded by the fact that in mining environments the pillars are not always cut according to the prescribed dimensions. Although the original design using either empirical methods or modelling may predict stable pillars, unstable pillars will be encountered in reality. Very conservative designs with large factors of safety may circumvent this problem, but this approach is uneconomical.A possible solution to localized stability problems may be to enhance the strength of a few unstable pillars. It may even be hypothesized that reinforcing a few critical pillars may prevent ‘pillar runs’ on a much larger scale. Rockbolting, strapping of pillars, and pillar shotcreting have occasionally been used in the past as possible solutions. It appears that these have not been successful in all cases and large collapses have occurred in spite of the pillar remedial work.The authors investigated the strapping of pillars by conducting laboratory tests on cabled rock specimens. The results were qualitatively compared to actual attempts of pillar reinforcement available in the literature, as well as additional observations in an old haematite roomand- pillar mine in Spain. Based on these results, the value of steel cabling and mesh wrapped around pillars to improve stability is demonstrated. Some cases where this approach will not be successful are also discussed."

Jan 1, 2017

By I. Kaabachi, F. Meunier, N. Morales

In open pit mining, ore and waste are hauled outside of the excavation area by trucks that move along a system of ramps. The design of these ramps must be carefully addressed because they have to comply with geomechanical constraints to ensure the stability of the pit walls, provide access to the different levels and phases, but also maximise the value of the extracted ore and reduce the extraction of waste. Because an optimisation approach able to deal with the design of the full ramp system seems to be out of reach at the moment, this paper addresses the problem of designing one ramp providing access to a single pushback, which has been determined beforehand. The optimisation objective is therefore to find a ramp that gives access to one given potential volume, while minimising its impact on the economic value of the volume. Two versions of the problem are formalised. One version allows the extraction of ore and waste only if this extraction is necessary for the ramp system. This version somehow minimises the intrinsic value of the ramp system. In the second version, it is possible to extract more than is needed by the ramp system. For instance, this takes into account the possibility of attaining ore on the wall opposite to the ramp as soon as the ramp reaches its level. In the setting mentioned above, the contribution of this work is three-fold. First, the computational complexity of the two different versions of the problem is presented and discussed; in particular, they are shown to be NP-hard. Second, compact integer programs modelling these two versions are proposed. Third, an efficient GRASP algorithm able to cope with the large instances of the problem is proposed. To assess the proposed approaches, the models and algorithms are applied to real instances with an off-the-shelf solver, illustrating and discussing their potential and relevance for the two versions of the problem. They are also compared with other approaches from the literature in terms of value and resulting designs.

Sep 1, 2021

By E. Wroth, D. G. Krige

Written contribution E. Wroth* (Visitor): The technical aspects of the assistance scheme which IS provided for in the Gold Mines Assistance Act, 1968, and certain consequential amendments to the Income Tax Act, 1962, are explained by Dr Krige. The object of this contribution is to explain the working of the Gold Mines Assistance Act (hereafter referred to as the 'Assistance Act') for the benefit of those concerned with the tax and assistance assessments of gold mining companies. The views expressed do not necessarily reflect the Revenue Department's interpretation of the legal provisions involved. 1. MINES WHICH QUALIFY FOR ASSISTANCE 1.1 The assistance scheme is applied on a selective basis. Mines which qualify for assistance are defined in the Assistance Act as 'assisted gold mines'. The requirements for classification as an assisted gold mine are that: (i) the mine be a producing gold mine; (ii) it would be likely to close down within eight years if not assisted; and (iii) with State assistance its life would be appreciably prolonged and there would be a significant increase in production of gold or uranium, or of both gold and uranium. 1.2 A mine is only considered for classification as an assisted gold mine on application. Such applications must be made to the Mining Leases Board through the Government Mining Engineer. Classification of a mine as an assisted gold mine is at the discretion of the Minister of Mines who acts in consultation with the Minister of Finance and has regard to the recommendations of the Mining Leases Board. 1.3 The Minister of Mines will impose conditions subject to which a mine is to be classified as an assisted gold mine. The most important will be that the mine must immediately lower its operating pay limit, as normally calculated, by a percentage fixed by the Mining Leases Board and conduct its future mining operations in accordance with the average grade of its ore reserves determined on the basis of such lower pay limit. l.4 The Minister will fix the date as from which classification as an assisted gold mine is to be effective. So long as the mine has operated on the basis of the lowered pay limit for at least three months during the particular year of assessment, he would normally fix the effective date as the first day of the year of assessment.

Jan 5, 1968

By G. L. Smith, B. Genc, V. Morar, U. Govender

This paper presents a novel holistic healthy human framework for C-suite executives and senior leaders in the minerals industry. The value-add of the framework centres around the integration of inner holistic health and interpersonal holistic health to support and enhance environment, social, and governance transformation, with a focus on the social enterprise. The framework unpacks key components of holistic health and their interlinkages to environment, social, governance, and stakeholder engagement. Insights were gleaned from interviews with 10 C-suite executives, each with over twenty years of experience in mining or business leadership. By applying the holistic healthy human framework, industry leaders can strengthen the social licence to operate and positively transform the industry's public image. Broader application to other sectors is underway.

Oct 2, 2025

By J. Hadjigeorgiou, T. R. Stacey

This paper introduces the Quantified Value-created Process (QVP), a decision-making process for use in mine design and operation. The implementation of the QVP is founded on a ten-step rock engineering design process and a ten-step strategic planning process. The potential of this approach is demonstrated by examples of value created as a result of good research, design, and planning. The QVP is divided into two parts, namely, a ‘planning the process’ section and an ‘implementing the process’ section, and can be considered to be an extension of the risk approach. All costs, direct and indirect, associated with a significant mining decision (design, operational, investment) must be quantified in advance of committing to that decision, to determine the value that will be created in the short, medium, and long terms. Ethical values, associated with health, safety, the environment, public perception, and social aspects, may be difficult to quantify in economic terms, but must nevertheless also be considered. In contrast with a traditional risk approach, the QVP will identify the upside, and allow executives to make more informed strategic decisions. In this context it is essential to actively engage upper management in the decision process.

Feb 2, 2022

By X. Chen, G. Wang, D. Wan

Computational fluid dynamics have been applied for detailed modelling of particle-bubble collisions. The most accurate approach in the previous work is using the point particle method to treat particles and bubbles. Nevertheless, the sizes of particles and bubbles are generally bigger than the Kolmogorov scale in the high turbulence of the flotation environment, which makes the point particle method inappropriate. This paper describes particle-resolved direct numerical simulation on the collisions between particles (denoted as heavy particles) and bubbles (denoted as light particles) in a homogeneous isotropic turbulent flow field, and a comparison with the point particle method.. A largescale stochastic forcing scheme was implemented within the mesoscopic multiple-relaxation-time LBM approach to maintain turbulence intensity at targetted levels. Both kinematic and dynamic collision kernels were evaluated to study the correlation of total collision events and turbulent kinetic energy (TKE) dissipation rate. The results show that collisions between particles increase with the TKE dissipation rate as radial relative velocities between particles increase with it. In the particle-resolved simulations, the dynamic collision kernels were found to not match with the kinematic collision kernels as in the point particle method. Quantitatively, they were approximately 4 to 10 times smaller than the corresponding dynamic collision kernels. Therefore, it is not reasonable to estimate the kinematic collision kernel in particle-resolved simulations as its rationales are not valid. However, the collision behaviour can still be accounted for by means of the dynamic collision kernel since it is obtained from the direct statistical analysis of the collision events. Keywords: Lattice Boltzmann Method; particle-resolved simulation; multiphase flow; collisions

Jan 1, 2020

By P. de A. Barbosa, M. G. Bergerman, E. da Fonseca

Located in the state of Pará, Brazil, the Sossego copper and gold mine consists of a heterogeneous geological deposit. Its complexity derives from the hydrothermal alteration, the ore-forming event, which modified the host rocks, such as granite, and metamorphosed volcanic rocks into several mineral assemblages. Different mineral assemblages have led to differences in abrasiveness. A few Bond abrasion tests conducted during the mine feasibility study did not provide a robust abrasiveness database, thus the variation of physical properties for some mineralisation host rocks was not possible. Although several test methods may be used to determine ore abrasiveness, the Bond method is the one most commonly used in the mining industry. Despite being simple to carry out, this test method has certain limitations as to particle size and the amount of ore sample required, which often makes it difficult or even impossible to apply in the early stages of a project and in geometallurgical studies. The Laboratoire Central des Ponts et Chaussées (LCPC) test may provide an alternative, as it requires a smaller amount of fine-grained material. This study aimed to provide data on wear properties of various ore types from Sossego mine using the LCPC method. It included validation for 40 different ore samples using the Bond test as a benchmark. The results showed good correlation, indicating it may be possible to use the LCPC test as an alternative to the Bond abrasion test. A high abrasiveness index was found for acid metavolcanic rock, confirming the results observed in Sossego mill’s operating database, pointing to a mineralogical drive to amorphous quartz. Keywords: Abrasiveness, geometallurgy, copper ore, Bond abrasion test, LCPC

Jan 1, 2020

By S. Mohanta, B. C. Melkap

"SynopsisDry beneficiation of coal by air dense medium fluidized bed is an emerging trend. It is widely believed that the particle size of the medium has a significant effect on the separation efficiency. This investigation demonstrates that medium particle size has a major effect on separation efficiency. Experimental results show that different size fractions of the same feed respond differently to the same size fraction of medium solids. Furthermore, a particular size fraction of feed coal responds differently with different size fractions of medium solids. The Ep values and overall metallurgical performance parameters, obtained from experimental results, clearly indicate the superior performance of an air dense medium fluidized bed separator when using –150+106 µm magnetite powder as the fluidizing medium. These observations reinforce the importance of sizing the medium particle size for the air dense medium fluidized bed.IntroductionIn an air dense medium fluidized bed (ADMFB), a fluidizing bed of a particular density is created by suspending solid particles in an upward air flow. A feed containing coal particles of different densities is introduced into this fluidizing bed. The particles with relative density less than the bed density float on the top of the bed, while particles denser than the bed density sink through it. Since there is a general correlation between ash content and density of coal particles, it is possible to remove ash-forming impurities from a raw coal to the required level by regulating the density of the fluidizing bed. Recently, the ADMFB process has received significant attention world-wide for its specific advantages of low operating cost and less restrictive for small capacities (Luo and Chen, 2001; Houwelingen and de Jong, 2004; Dwari and Hanumantha Rao, 2007; Sahu et al., 2009; Mohanta et al., 2012). This process is not recognized as a well-established industrial practice because of the availability of efficient wet processing technology. However, with the revival of interest in dry beneficiation of coal in general, and ADMFB in particular, there is a concerted effort to improve the efficiency of the ADMFB process, and successive improvements have made the process a competitive and viable option for beneficiating coal."

Jan 1, 2015

By N. Lock

"Despite the pre-eminence of the Jwaneng Diamond Mine as the world’s richest diamond mine, the discovery story has long been clouded in mystery. This is the 45-year old untold story of the Jwaneng discovery and contemporaneous Bechuanaland/Botswana political and socioeconomic history. Diamond exploration by De Beers in Bechuanaland began in 1955, with the first true kimberlite discovery near Letlhakane in 1967, before Clifford’s Rule was applied and before the use of indicator mineral chemistry. Surface deflation soil sampling and bioturbation by termites was the foundation for exploration into the Kalahari. The 1962 reconnaissance programme south of Jwaneng had failed to make any discoveries. Improved sampling methods were applied to the Kalaharicovered areas in 1969 and positive results were received by year-end. The Whateley’s Wish percussion drill-hole in December 1972 was confirmed as Jwaneng 2424D/K2 with drill core in early 1973. Jumper drills were required to penetrate the Kalahari sand cover. Diamond resources were demonstrated despite multiple technical problems. IntroductionThe Jwaneng Diamond Mine is, by value, the world’s richest diamond mine. Harry Oppenheimer is quoted as saying that Jwaneng is ‘the most important primary deposit found anywhere in the world since the discovery at Kimberley more than a century ago.’ (Taylor III, 1982) The mine opened in 1982 after some nine years of evaluation and construction since discovery in February 1973. Debswana (2017) states that 2015 production was 7.87 Mt of ore from which 10.408 million carats were recovered at a grade of 132 carats per 100 t (cpht). Although the value is not reported, it was noted that Jwaneng contributes 60–70% of Debswana’s total revenue from all mines, including Orapa, Damtshaa, and Letlhakane (Debswana, 2017)."

Feb 1, 2019

By M. Grave

Rock Engineers are required to design safe cost effective support systems and stoping layouts for their respective mines. As each stope has its own unique environment, continual re evaluation is required in all stopes to maximize extraction and achieve value from the support standard. This paper presents numerical modelling used to plan early mining within the shaft pillar and a reevaluation of an existing stope support standard.

Jan 1, 2009