Search Documents

By Roger A. Blais, Michel David

"Matheron's geoslalislical method for the estimation of ore reserves has been developed to the point at which real-life problem may be handled effectively. The steps involved in the method are:(i) obtalning the variogram,(ii) fitting a model, and(iii) producing block estimates.All three steps may cause difficulty, and would-be users need a deep understanding of the theory if failure is to be avoided.To illustrate these points, specific cause are considered:(i) two almost equidimensional porpbyry deposits, one drilled randomly and the other regularly; and(ii) two iron formation, one drilled extensively and being mined, while the other is still at the stage of early estimation."

Jan 1, 2014

By V. A. Leão, V. S. Coimbra, V. A. A. Oliveira, R. F. M. de Souza, G. M. de Lima

A willemite concentrate consisting mainly of willemite (55.3%) and dolomite (15.6%) was reduced in a tube furnace with charcoal as reductant. The effects of temperature and varying reductant additions on zinc extraction were studied. A zinc recovery of 86% was achieved with 20% reductant in the charge at 1100°C. During reduction, the calcium oxide generated through calcination of the dolomite promoted decomposition of the willemite, thus lowering the temperature at which reduction took place. The presence of CaO improved the zinc recovery at all temperatures studied. The best zinc recovery (93%) was obtained in the presence of 5% CaO, 20% charcoal reductant, and at a temperature of 1100°C. The results show that the willemite concentrate studied has great potential to be used as a raw material for the Waelz process.

Nov 6, 2023

By V. Sheikhzadeh, S. M. H. Haddad, M. Saghaeian, N. Esmaeili, R. Hejazi

One of the most significant features of iron ore concentrate (pelletising feed) is the specific surface area (SSA) that affects the achievement of desirable pellet properties. There are various methods to determine this parameters and currently, the most common is the Blaine air permeability method. However, due to the simplified assumptions including spherical and identical particles and 50% bed porosity, the Blain test does not provide accurate results. In fact, these two suppositions are far from reality. In this research, comparison of SSA measurement ways are investigated, containing laser diffraction testing and Blaine air permeability, on samples with different SSA, obtained from Ball mill and high pressure grinding rolls (HPGR). The output data showed that the calculated amounts of SSA by means of laser analysis were far greater than any other one. Furthermore, in the same results of Blaine air permeability tests on samples comminuted by different grinding methods, it was observed that the SSA figures from the laser diffraction method for HPGR products were almost 800 units greater than Ball mill ones. Keywords: Pelletising feed, specific surface area, Blaine air permeability, laser diffraction testing

Jan 1, 2020

"Chairman: Professor C. O. Frush Rapporteur: Mr A. C. SchmidtPapers:Planning of underground copper mining by J. K. Williams, L. Smith and M. P. WellsLinear programming models of copper leach and solvent extraction plants by W. P. C. Duyvesteyn, J. R. Cutland and J. R. L. RusselPlanning and forecasting stope production by D. W. Kappes and P. F. X. Moussett-JonesA proposed method of dynamic ore reserve assessment for a caving system of mining by A. F. Spinks and S. P. NicholsThe initial point made by Mr L. Smith in presenting his paper was that the planning aid outlined in the preprint was neither sophisticated nor complicated. However, it was a system which worked and was a very real way in which the computer was being used to assist miners, in particular, who at the present moment have very little experience in the use of computers.Mr Smith apologised for the fact that the editors of the paper had eliminated all reference to 'time'. This was very unfortunate because the essence of the system was that it saved time, which was one of the main points made in the paper.The operations being planned by this means cover the Rokana orebody which is a stratiform body mined by open stoping.The planner has to decide how much ore to mine from each base in each time period of his plan, that is, from three to four months hence to a year ahead. Normal procedure is for the planner to have discussions with the underground manager on some of the information he requires. The sort of information needed is (i) tramming limits for each face, (ii) extraction and grade factors, (iii) the present status of mining operations so that the planner knows where to start the new plan, and, (iv) details of any other mining consider¬ations that need to be incorporated in the plan.The objective at this point is to produce an initial plan for discussion purposes. All the information required comes from one sheet per stops and shows, inter alia, the stope identifier, the length along strike, the ore tonnage, the copper and cobalt grades and, finally, the extraction and grade factors.The program itself, among many other things, checks the data for validity, compatibility, completeness and credibility and prints error messages accordingly. Output from this system is in the form of a summary of production from each face, as well as giving the figures of ore reserve depletion. This summary indicates which slopes are to be mined in this time period, the original survey grades (copper and cobalt), the estimated production grades, how much is to be mined from each stope and the copper and cobalt production accordingly."

Jan 1, 2014

By S. K. Murphy

A partial shaft pillar extraction project was embarked on at a mine in the West Wits mining region in South Africa. Prior to the extraction, a rock engineering assessment was conducted with the main objective being to establish which areas of the shaft pillar could be extracted without unduly affecting the stability of major infrastructure within the shaft pillar. Standard numerical modelling methods were used to conduct this assessment and several areas were identified for extraction. However, during the extraction process, it was found that the infrastructure was affected more than was originally predicted by linear elastic modelling. In addition to this, several large events resulted in far more large aftershocks than would normally be predicted. In order to gain an understanding of this phenomenon, seismic data was integrated with numerical modelling as follows: > The seismic data in the form of displacements was integrated in 3D space within the model to assess the effect of static stress changes associated with seismic activity > Data from large events was integrated onto specific structures, where displacements associated with large events were integrated onto the plane of structure in question. This paper describes the methodology and results obtained from each of the above processes and include insights into the mining process that were previously unfathomable using standard linear elastic numerical modelling. The way forward for this rock engineering assessment of partial shaft pillar extraction is also discussed.

Jan 1, 2012

By S. Gan, E. van Niekerk, L. Birrell, D. Robbertze, L. Ncubi, B. Zhao

Quality assurance and quality control (or QAQC) plays a key role in safeguarding the level of confidence of the data generated during mineral exploration and mine development, and is also part of the reporting code requirements for resource estimation and reporting, as well as mining investment. Implementation of good policies and working protocols in quality management will result in the generation of reliable information, which is critical for decision-making on the future of the mining project. The use of certified reference materials, i.e., standard, blank, and duplicate samples, proves effective and efficient for ensuring the level of data confidence in terms of precision, accuracy, and sample contamination. This is well demonstrated by the practice of QC in the exploration programme for the chrysotile tailings storage facilities of Havelock Mine, using 1254 samples from 53 drill-holes. Different statistical tools were applied to analyse the assay results from these samples. The outcome substantiates that the QC practice established during the Havelock exploration project is aligned to best practice guidelines in the industry. The resource delineated indicates that the tailings material at Havelock could potentially become a significant source of supply to the global magnesium market.

Jul 2, 2022

By S-J. Park

When evaluating mining investment opportunities, one should consider the risks associated with mineral exploration and development. These are commonly classified as technical, economic, and political risks, and are accounted for in the investment decision by changing the discount rate. Thus, a company may use different discount rates associated with varying risks in order to compensate for the variability of success. The discount rate has a tremendous effect on the economic evaluation of mineral projects. Even when all other factors used as inputs for calculating the NPV (net present value) are equal, the project under consideration may be accepted or rejected depending upon the discount rate. Determining a realistic discount rate for a given project is therefore the most difficult and important aspect of cash flow analysis. It should be determined with the consideration of proper technical, economic, and political conditions surrounding the specific project undergoing economic evaluation. One key problem for determining the appropriate discount rate is that it typically depends more on subjective perception of the degree of risk or other experience factors than on a systematic approach. Thus, this study aims to identify, analyse, and document the type, role, and impact of risk factors influencing the determination of discount rates, and then to determine discount rate by using the aforementioned factors.

Jan 1, 2011

By K. Duffy, W. Valery, L. Pyle, P. Holtham

A conceptual scoping study was conducted to investigate pre-concentration options for upgrading ore from an Ag-Pb-Zn deposit. The low grade of the ore would result in only modest economic returns, given current market conditions. Several pre-concentration options were considered. These included: selective mining, crushing and pre-screening (following either standard or high intensity selective blasting), bulk ore sorting, particle sorting, jigging, dense medium separation, or combinations of these approaches. Flowsheets were developed for each option, and the upgrade performance was modelled using Limn to determine mass balances and stream tables. Due to the limited availability of test work data, the models were based not only on what test data was available but also on case study data found in the literature. The Bazin technique was used to derive assay by size data for different streams following crushing. Equipment lists and preliminary layouts were established based on the stream tables, and capital and operating costs were estimated for each flowsheet. This information was used to carry out a preliminary economic evaluation using net present value and sensitivity analysis. In this case, the most economically attractive process was found to be particle sorting; although further benefits may be realised by combining with bulk sorting. This paper describes the methodology used and the key findings of the study. Keywords: Pre-concentration, pre-screening, ore sorting, jigging, Ag-Pb-Zn, particle sorting, bulk ore sorting

Jan 1, 2020

By V. Maseko, C. Musingwini

"When considered collectively, Mineral Resources and Mineral Reserves are arguably a key asset for any mining company. Mineral Reserves are the economically mineable portions of Mineral Resources. They therefore provide a good indication of the economic prospects in the short to medium term and associated non-financial impairments for mining companies, hence a focus on Mineral Reserves. An assessment of modifying factors for converting Mineral Resources to Mineral Reserves revealed that Mineral Reserves were most sensitive to long-term commodity prices, hence the focus on long-term commodity prices. The justification for selecting gold and platinum mines is that they collectively make a significant contribution to South Africa’s earnings from mining.The introduction of the South African Code for the Reporting of Exploration Results, Mineral Resources and Mineral Reserves (SAMREC Code) in 2000 informed the basis for analysing long-term commodity price assumptions for major South African gold and platinum mining companies between 2000 and 2016. The analysis revealed that the least number of non-financial impairments occurred when long-term commodity prices were within ±5% of spot prices. This finding suggests that this range is the ideal range for long-term commodity price assumptions to improve confidence in Mineral Reserve declarations and minimize impairments. Introduction The South African Code for the Reporting of Exploration Results, Mineral Resources and Mineral Reserves (SAMREC Code) defines a Mineral Resource as ‘a concentration or occurrence of solid material of economic interest in or on the Earth’s crust in such form, grade or quality and quantity that there are reasonable prospects for eventual economic extraction’ (SAMREC, 2016, p. 18). Mineral Resources are categorized according to increasing levels of geoscientific confidence or knowledge, from Inferred to Indicated and lastly, Measured categories. The SAMREC Code defines a Mineral Reserve as ‘the economically mineable part of a Measured and/or Indicated Mineral Resource’ (SAMREC, 2016, p. 25). In some of the other reporting codes such as the Australasian Code for Reporting of Exploration Results, Mineral Resources and Ore Reserves (the JORC Code), a Mineral Reserve is synonymous with an Ore Reserve. The conversion of Mineral Resources to Mineral Reserves involves applying modifying factors, which are non-resource considerations. The modifying factors used in the Mineral Reserve estimation process include mining, metallurgical, processing, infrastructure, economic, marketing, legal, environmental, social, and governmental factors. Each of these modifying factors consists of several components which require due consideration in the estimation of Mineral Reserves. Table I shows some of the components typically considered for each of the modifying factors."

Mar 1, 2019

By R. A. Plumbridge

The Honourable Mr Molefe, Premier of the North- West Province; Or Scot-Russel, Chairman of the CMMI's XV Congress; Mr Loton, Chairman of the CMMI; distinguished guests, ladies and gentlemen. At the outset may I express my sincere appreciation to the organisers of this Congress for their kind invitation to me to participate in the plenary session. May I also thank the CMMI for inviting me to be their fifth distinguished lecturer. This is a signal honour and one which is sincerely appreciated by my Group and myself. The subject of gold is a very emotive one. It conjures up different images in the minds of a wide variety of people. For many of us it is very simply the ultimate metal. In ancient times gold was sought after and treasured; it was the chosen metal for adornment and many of the best preserved artefacts of that time were hand-fashioned from gold which had been won by primitive mining techniques. Gold's rarity and its value was recognised by those who fashioned the earliest gold coins thus underlining gold's special place as a store of value.

Jan 1, 1994

Council and Standing Committees - 1983/84 President: Prof. R.P. King Vice Presidents: J.D. Austin and H.E. James Honorary Treasurer: Prof. D.G. Krige Immediate Past President: Prof A.N. Brown Members of Council: B.C. Alberts, Prof. S. Budavari, N.J. Devine, Dr C.J. Fauconnier, P.T. Fewell, C. E. Fivaz, J. S. Freer, Prof. G.G. Garrett, J.J. Geldenhuys, Dr A.K. Haines, Dr B.K. Loveday, G. Pienaar, B.E. Protheroe, Dr O.K.H. Steffen, G.C. Thompson, Dr H. Wagner, Dr P.T. Wedepohl Chairman, Witbank/Middelburg Branch: H.C. van Zyl Chairman, Orange Free State/Klerksdorp Branch: D.A. Parfitt Past Presidents Serving on Council: Dr M.G. Atmore, Dr J.P. Hugo, Dr P.R. Jochens, Prof. R.P. Plewman, G.Y. Nisbet, Dr R.E. Robinson, Prof. M.D.G. Salamon, P.W.J. van Rensburg, D.A. Viljoen, P.A. von Wielligh Standing Committee Chairmen: Adjudication, Prof. A.N. Brown; Awards, Prof. A.N. Brown; Banquets, J.S. Freer; Constitution, Rules and Policy, Prof. A.N. Brown; Excur¬sions, J.S. Freer; Journal, H.E. James; Membership, H.E. James; Phoenix National Committee, Dr M.G. Atmore; SAIMM School - Extractive Metallurgy, Dr A. K. Haines; SAIMM School - Mining, Dr H. Wagner; Special Publica¬tions, J.D. Austin; Technical Programme - Extractive Metallurgy, Dr B.K. Loveday; Technical Programme - Mining, G. C. Thompson; Technical Programme -Physical Metallurgy, G. Pienaar; Training, Career Guidance and Education, Dr M.G. Atmore; World Mining Congress - National Committee, Prof. R.P. Plewman; Working Group Physical Metallurgy, Prof. G.G. Garrett

Jan 1, 1984

By B. S. Agbenuvor, R. Morrison, V. Jokovic, C. Antonio

Body breakage usually involves breakage of particles by compression between two surfaces or impacted against a rigid surface, with the latter of interest in this current study. This mode of breakage has been identified to be the most elementary size reduction process and the most effective breakage process in comminution devices. It has been found in the literature that the progenies produced from this form of breakage possess a residual velocity at which they move, after the breakage event. In the pursuit of efficiently utilising applied comminution energy, a laboratory-scale breakage device has been developed to deliver precise specific impact breakage using the concept of a fast-moving hammer and a slow-moving particle to effect breakage. The residual velocities of the progenies from the breakage event may be used to generate secondary breakage without further addition of energy if the particle encounters a stiff obstacle such as a steel plate at right angles to its path. To measure the extent of secondary breakage, the steel wall of the device was lined with a rubber material to suppress the second set of breakage events. The performance of the new device is analysed, based on calculated t10 values and measured residual velocities of the moving daughter particles. Testing involving anvils showed a much finer PSD and higher t10 compared to the test involving rubber lining. This finding is corroborated by the measured residual velocities of the progenies. The resulting energies calculated from the measured residual velocities of the progeny were found to be approximately 42-88% of the primary specific impact energy. This retained energy was found to be sufficient for secondary breakage. Keywords: Impact breakage, residual velocity, secondary breakage, energy utilisation

Jan 1, 2020

By J. T. M. Amphlett, C. A. Sharrad, M. D. Ogden, R. I. Foster

"A renewed interest in nuclear power around the world in order to reduce greenhouse gas emissions is going to increase demand for uranium as fuel. This will result in more uranium being mined, which will in turn increase associated environmental pressures, such as fresh water use. A move to lower quality waters containing impurities such as chloride would help alleviate these pressures. In this work, we determined the uptake characteristics of weakly basic anion exchange resin Ps-EDA towards uranium from saline solutions in a dynamic flow column. Breakthrough curves were produced, with suppression of uptake being observed for chloride concentrations above 5 g L-1. Calculated resin saturation capacities at zero and 5 g L-1 chloride are comparable with literature values for strong-base anion exchange resins, and exceed those published for weak-base resins up to 20 g L-1 chloride. Data has been fitted to multiple breakthrough models, with the modified dose-response model most effectively predicting uranium recovery. The results show that the ethylenediamine functionality could be suitable for use in future uranium processing flow sheets where a high-saline lixiviant is used. IntroductionIon exchange (IX) is a key technology in the uranium mining industry and is well established for the extraction of uranium from both acidic and alkaline leach liquors (Edwards and Oliver, 2000). It was first employed in 1952 at the West Rand mine in South Africa (Ford, 1993; Taylor, 2016). H2SO4 and Na2CO3 are the most commonly employed lixiviants used to solubilize uranium in acidic and alkaline leach conditions respectively. The chemistry of these systems causes uranium to form anionic sulphate or carbonate complexes, which can be taken advantage of by anion exchange resins.Another major technology for the extraction and purification of uranium from leach liquors is solvent extraction (SX). This technique involves the extraction of uranium from the aqueous phase into an immiscible organic layer. Although this is a commonly used method, there are major drawbacks to it, including the use of large volumes of flammable solvents, solvent loss, phase disengagement, third phase formation, and the production of problematic degradation products (Veliscek-Carolan, 2016). These problems can be circumvented through the use of IX resins."

Dec 1, 2018

By I. B. Fernandes, M. A. Reuter, A. Abadias Llamas

Metallurgical simulation and evaluation of the resource efficiency of whole production processes are of key importance for impact assessment, in terms of environment and resources. Exergy is a measure of resource consumption, taking into account energy, raw materials, water, and chemicals; which allows for the evaluation of different technologies to find the most resource efficient and environmentally friendly process. This paper compares the sustainability for production of rare earth magnets from primary and secondary resources through an exergetic evaluation of the production process, in addition to traditional life cycle assessment (LCA). The methodology makes use of simulation tools for tracking material flow and resources used, based on thermodynamic laws, from ore exploitation to magnet production and recycling. It highlights areas with the greatest potential for improvements in terms of resource consumption and environmental impact generation, having a thermodynamic-validated flowsheet for primary and secondary production of NdFeB magnets, present in several low-carbon technologies, such as wind turbines, electric vehicles, and cooling systems. It demonstrates the minimum exergy destruction for magnet production, through an irreversibility breakdown chart, showing where irreversible material and energy losses occur. Results show that CO2-equivalent emissions for producing NdFeB permanent magnets from primary resources could be twice as high when compared to magnets produced from recycling technologies. The theoretical maximum exergetic efficiency for primary production is 57.61%, whereas for permanent magnets produced from secondary resources, the exergetic efficiency reaches up to 82.89%. Two magnet recycling technologies were evaluated, i.e. in acidic medium and via hydrogen decrepitation, and it was observed that their exergetic efficiency and environmental impact performed better than production from primary resources. Keywords: Resource efficiency, exergy analysis, permanent magnet recycling, process simulation, system design

Jan 1, 2020

By Y. Rao, Y. Huang, G. Wang, W. Liu

The properties and deterioration in strength of cemented tailings backfill (CTB )in the underground acidic environment under oxidizing conditions were studied. X-ray diffraction analysis and scanning electron microscopy of the surface of the CTB was carried out, and the sulphuric acid corrosion mechanism elucidated. The properties tested included compressive strength, elastic modulus, cohesion, internal friction angle, variation in the hydrogen ion concentration, and stress-strain relationship in different corrosion periods. The damage model of the CTB was established considering the effects of parameters such as corrosion time and strain on the damage evolution. It was found that the compressive strength, elastic modulus, cohesion (binder effect), and internal friction angle increased at first and then decreased with exposure time. In the long term, the peak stress decreased with corrosion time while the peak strain increased; elastic modulus, and deformation modulus also decreased. The damage caused by corrosion and by load were related by means of a mathematical model, which revealed the relationships between sulphuric attack, load, and damage to backfill in complex underground environments. During corrosion, the expansion of gypsum and ettringite caused microfractures in the CTB. With increasing corrosion time, micro-cracks developed and proliferated. The mechanism of corrosion damage was found to be the dissolution of hydrogen ions and a sulphate ion reaction that produces an expansive substance, resulting in deterioration of the strength of CTB.

Jun 1, 2021

By J. Sehata, J. Tshilongo, I. Govender, S. Pikinini, T. L. Moodley, M. Raedani

In the face of dwindling Merensky ore reserves in the early 1990s, Mintek developed the MF2 flotation circuit to economically recover platinum group metals from the shallow upper group-2 chromitite reef. By aligning the primary and secondary grind to the platinum group metal liberation kinetics, excessive fine chromite generation was avoided, and thus one could consistently produce high-grade concentrates (>200 g/t platinum group metals) with low chrome content (<3% Cr2O₃), well within smelter tolerances. This, coupled with upper group- 2's low-cost open-pit mining, made it particularly attractive to investors and mining houses alike. As a result, deeper lying reefs like middle group and lower group with lower platinum group metals grades and complex mineralogy, were primarily mined only for chromite using density-based separation processes (like spirals), of which the waste tailings are best classified as secondary platinum group metals resources. Today, with global platinum group metal demand rising and high grade upper ground-2 reserves rapidly diminishing, the industry must revisit these middle group and lower group tailings. Mineralogical analysis reveals several challenges: Middle group tailings feature platinum group metals locked within silicate matrices, while lower group tailings contain fine chromitite fragments, and are hosted within non-floating laurite grains, each presenting liberation and gangue issues. Smelter constraints still demand concentrates below 3% Cr₂O₃, requiring solutions that consider both platinum group metals recovery and chrome entrainment. To develop a solution, two lower group chrome spiral tailings samples were obtained from a large chrome mine: Sample A (+425 μm – 106 μm) and Sample B (−106 μm). Initial assays showed Sample B contained higher platinum group metal grades but also higher Cr₂O₃. As such, different blends of flotation feeds were evaluated using ratios of 90:10 (C1) and 80:20 (C2) of Sample A to Sample B, targeting the coarse fraction's lower chrome content while recovering valuable platinum group metals from the fines. This work proposes a practical route for mining houses to unlock additional platinum group metal value from lower group ore spiral tailings. By optimising blending ratios and reagent suites, it is possible to meet smelter chrome and platinum group metal grade thresholds, whilst still obtaining economically viable PGM recoveries.

Mar 6, 2026

By F. Qunfei, W. Laijun, X. Lyu, A. Cosmos, L Huijuan, Z. Jinggang, G. Yao

In this paper, four cyanide-utilising bacteria strains were isolated from a gold mine tailings pond, in the Hexi gold mine (Shandong), China. Based on the analysis of 16S rRNA gene sequence, four strains were identified as Aeromonas hydrophila strain C1, Bacillus mojavensis strain C3, Shewanella oneidensis strain C2, and Aeromonas media strain C4. Based on the cyanide detoxification efficiencies results of the four strains, Bacillus mojavensis C3 had the highest detoxification rate and was selected to assess its efficiency to detoxify cyanide in gold mine tailings at different pH (9.5, 10.5, and 11.6) using cyanide as the sole carbon and nitrogen sources. Strain C3 was capable of detoxifying 46.5mg/L of cyanide-containing gold mine tailings at all tested pH ranges at 30oC, 196 rpm after 15 d. The amounts of cyanide detoxified were 87.5%, 84.1%, and 73.5% at initial pH 9.5, 10.5, and 11.6, respectively. The highest cyanide detoxification was observed at pH 9.5. The viable cells growths in the samples were 5.7E+09CFU/mL, 4.9E+09CFU/mL, and 2.7E+09CFU/mL at pH 9.5, 10.5, and 11.6, respectively. Free ammonia concentrations were observed as a byproduct of the biodetoxification process. The residual ammonia concentration in the sample was observed at 0.35 mg/L, 0.33 mg/L, and 0.62 mg/L at pH 9.5, 10.5, and 11.6, respectively. The highest residual ammonia concentration was noticed at pH 11.6. The amount of cyanide removed by mixed culture strains C3 and C4 was 94.6% and showed a residual free ammonia concentration of 2.6mg/L, as biodetoxification byproduct after 120 h. The pure culture Bacillus mojavensis strain C3 and its mixed culture strains exhibited higher potential to detoxify cyanide-containing gold mine tailings at alkaline pH values and could be cultivated to detoxify gold mine effluents at large-scale. Keywords: Bacteria strain, cyanide, detoxification efficiency, gold mine tailings

Jan 1, 2020

By J. J. Taute, S. J. Archer

"BASF Mining Solutions has developed a new-generation copper solvent extraction reagent that offers significant benefits over standard extractants currently available to the industry. As the name suggests, the new hightemperature (HT) extractant can be used at a higher operating temperature, but also exhibits significantly lower degradation rates, greater copper-toiron selectivity, and is totally nitration-proof compared with the standard extractants. Pilot-plant trials have also shown that lower aqueous-inorganic entrainment can be achieved. This paper investigates the technoeconomic benefit of using the HT extractant as an alternative to the standard extractant in a high-temperature application. The results of the technical evaluation showed that the use of the HT extractant reduces the extractant addition requirements and bleed volume from copper electrowinning; this smaller bleed requirement further reduces acid and limestone consumption, leading to a reduction in valuable metal losses. The results of the economic evaluation showed that the use of the HT extractant represents significant cost savings over that of the standard extractant. IntroductionCurrent solvent extraction (SX) reagents employed for the extraction of copper from typical pregnant leach solutions (PLS) at ambient conditions function well with minimal long-term effects on the extractant’s performance (Taute et al., 2015). This performance, however, deteriorates at elevated temperatures due to the degradation of the reagent’s hydroxyoximes. The degradation mechanism, acid-catalysed hydrolysis of the oxime, is accelerated by high temperature. This has a knock-on effect where the increase in degradation products increases the organic viscosity, leading to increased entrainment, crud formation, and ultimately to an increase in SX reagent consumption (Bender, Emmerich, and Nisbett, 2013).SX reagents also show an increase in the co-extraction of iron as the ferric concentration in the PLS increases. Co-extracted iron is transferred to electrowinning (EW) during stripping of the loaded organic and can adversely affect EW current efficiency. Iron in the EW circuit is typically managed by bleeding the electrolyte; however, this can lead to excessive consumption of EW reagents such as acid, cobalt, and mist-eliminating surfactants. The electrolyte bleed can also affect upstream consumption of reagents, such as lime, due to the high acid concentration recycled to leach."

Nov 1, 2018

By F. Dinter, C. McGregor, Q. G. Reynolds, L. Hockaday

The necessity of reducing greenhouse gas emissions to limit the impact of anthropogenic climate change means that all industrial processes should investigate their options towards decarbonization. Iron, steelmaking, aluminium, and cement production produce the most industrial emissions. Although most research focuses on decarbonizing these industries, minerals processing industries must be decarbonized to achieve net zero emissions goals by 2050. Incorporating renewable energy sources and avoiding the combustion of fossil fuels are two ways to reduce greenhouse gas emissions. This paper reports on the results from a dynamic process model developed to investigate the feasibility of concentrating solar thermal pretreatment of manganese ores to pretreat carbonate-rich manganese ores for increased ferromanganese smelter productivity and reduced greenhouse gas emissions. The results indicate that pretreated ores reduce the energy requirement for smelting significantly for some ores and lowers total carbon dioxide emissions by 13 to 19% compared to the traditional smelting route. A high-level economic evaluation shows that solar thermal treatment is financially viable for low cryptomelane, high braunite ore that is common in the Kalahari Manganese Field.

Dec 11, 2024

By S. Michael, T. E. Moongo

Electrowinning consumes a substantial amount of electrical energy, and owing to the ever-increasing unit cost of electrical power there is a need to improve current efficiency in the process. This research was carried out to design a continuous quality improvement framework for improving electrowinning current efficiency by applying statistical process control (SPC) on an online industrial copper electrowinning operation. A sequential mixed research methodology was applied and a statistical software package utilized for analysing data. It was concluded that metallurgical short-circuits (hotspots) had the most significant effect on current efficiency. Bringing hotspots under statistical control resulted in a 5.40% improvement in current efficiency, which is equivalent to approximately 74 t of 99.999% pure grade A copper cathode production over a period of 1.5 months.

Jan 1, 2021