Search Documents

By H. Mulder, M. C. Bekker

The objective of this paper is to describe the research followed in creating a generalized, readiness assessment tool for mining projects. We start by highlighting the need for the assessment tool and then progress towards explaining the methodology followed during the study. The selection and finalization of the list of elements, sections, and categories that make up the unweighted values are described, followed by a summary of the weighting process applied. The outcome of this process is a weighted readiness assessment tool for mining project studies. The main benefits of the tool are that it will guide decision-makers and project managers through the definition phases of the project and improve the likelihood of project success.

Jul 2, 2022

By D. Nardini

The need to move towards faster and safer mine development is a key priority in mining houses globally. In addition to this, South Africa faces an array of challenges introduced by labour-intensive operations; hence a study was conducted to look into improving development rates and labour productivity, specifically in the areas where trackbound flat-end development is required. The aim of the study was to propose a method to deliver fit-for-purpose tracked tunnels that advanced at a rate of one blast per end every single working day. A major part of the study was to optimize the selection of an appropriate trackless fleet and mitigate any constraints introduced with the mechanization. This was done by creating scenarios, based on a typical case study, looking into the aspects around safety, mine design, mine activity cycling, men and machine requirements, service installations, and trackless-trackbound interfaces. The case study was based on a deep-level gold mine developing twin headings with connectings; however, with the move to extend and deepen platinum operations it is foreseen that twin end development will become more prevalent due to ventilation, logistical, and other requirements. With the introduction of the trackless mechanized system suggested, development rates of 56 m of system advance are expected (189 m total development), with on an average of three headings and fixed blast times. Scenarios run with multi-blast conditions yield expectations of 75 m/month advance of the system, significantly higher than the conventional performance seen today.

Jan 1, 2012

By J. A. L. Napier

One of the most important characteristics of tabular mine stress analysis is the need to represent the complex evolution of mining face positions and the accompanying induced stress changes in the rock mass. Integration of seismic activity with numerical modelling requires flexible and efficient solution schemes in which both off-reef damage and large-scale fault slip can be effectively represented. A new approach is investigated in which the stope closure and ride variables can be found using a moving least squares estimator. Some advantages of this approach over traditional element-based tessellation schemes are identified. At the same time, shortcomings of this method are noted when the displacement discontinuity variable is approximated by a polynomial shape function. Difficulties and possible solutions to the shape function formulation near excavation edges are discussed. Une des caractéristiques les plus importantes de l’analyse des contraintes minières tabulaires est la nécessité de représenter la complexe évolution des positions du front de taille et des changements concomitants des contraintes occasionnées dans la masse rocheuse. L’intégration de l’activité sismique avec la modélisation numérique requiert des projets souples et efficaces qui permettent la représentation des dommages hors-filon et des glissements de faille à grande échelle. Une approche nouvelle est étudiée qui permet de trouver la fermeture de la taille et les variables de montage en utilisant un estimateur par les moindres carrés mobile. Certains des avantages de cette approche sur les traditionnels projets basés sur une structure en mosaïque sont identifiés. En même temps, les défauts de cette méthode sont notés lorsqu’on calcule la variable de discontinuité du déplacement approximativement par une fonction de forme polynomiale. Les difficultés et solutions possibles à la formulation de la fonction forme près des bords d’excavation sont discutés. Eine der wichtigsten Charaketeristika der taublaren Grubenspannungsanalayse ist die Notwendigkeit, die komplexe Entwicklung der Abbaupositionen und der damit verbundenen induzierten Spannungsänderungen der Gesteinsmasse neu vorzulegen. Die Integration der seismischen Tätigkeit mit einem numerischen Modell erfordert flexible und effiziente Lösungsschemata, in denen sowohl Schäden ausserhalb des Riffs als auch Verwerfungen großen Ausmaßes effektiv dargestellt werden. Ein neuer Vorstoß wird untersucht in welchem die Strossenschliessung und Schneisenvariablen unter Verwendung des Schätzwertes der kleinsten quadratischen Abweichungen (Gaussscher Schätzwert) gefunden werden. Einige Vorteile dieser Annäherung im Vergleich zu der traditionellen Element-basierenden Tessellation sind identifiziert. Gleichzeitig werden Unzulänglichkeiten dieser Methode vermerkt, wenn die Verschiebungsdiskoniuitätsvariable durch eine polynomische Formfunktion angepaßt wird. Schwierigkeiten und mögliche Lösungen zur Formfunktionsformulierung nahe Exkavationsrändern werden besprochen.

Jan 1, 2003

By K. C. Corin, M. Tadie, R. M. Manenzhe

The near depletion of high-grade ores, among other factors, has necessitated the consideration of alternative PGM sources. Various factors in the metallurgical processing of ores result in valuable minerals being lost to the tailings, and hence, PGM tailings are a possible alternative PGM source. However, as the value residing in PGM tailings remains unquantified and uncharacterised, there is a challenge in knowing the recoverable fraction of value contained in PGM wastes. This paper outlines the in-situ techniques of oxygen uptake and EDTA extraction for their possible use for determining the recoverable value in PGM tailings. Both methods have shown efficiency in determining the weathering of sulphide minerals and sulphide-bearing ores. Keywords: PGM tailings, tailing retreatment, oxidation, oxygen decay, EDTA

Jan 1, 2020

"Chairman: Professor J. C. Griffiths Rapporteur: Mr J. P. G. PRETORIUSPapers:Mine-mill production scheduling by dynamic programming by R. J. Roman Optimization of a large mining venture by J. C. Paynter, B. K. Loveday and C. G. Robinson Economic surface mining of multiple seams by T. V. Falkie and W. E. PorterIn introducing his paper, Mr Roman said that whereas in manufacturing plants the yearly production levels were usually chosen to produce the largest annual cash flow, in a mining operation, the raw materials (ore) were exhaustible so that the production had to be scheduled to maximize the total net present worth of the operation. This optimum production schedule could be determined by using dynamic programming. The required information was readily available to management at most mines. The 'possible operating range' of production rates lay between the rate with the highest profit per ton. and that with the highest profit per year. The optimum production rate started typically at the top of this range and decreased slowly as the deposit was depleted.Dynamic programming was used to determine several production schedules for a hypothetical mine-mill complex. The effects of changes in the ore grade estimates, size of deposit and acceptable rate of interest on the production schedule were taken into account. Apart from the fact that the net present worth of the overall profits was larger than that obtained by conventional methods, it appeared from the cases studied that the amount of metal recovered was also greater.Dr it P. King commented that this was a very interesting application of dynamic programming. He pointed out, however, that the market price of the metal was likely to vary significantly and randomly during the life of the mine, and he suggested that the problem should, therefore, be reformulated as a stochastic dynamic programming problem.If the price of the metal rose to abnormally high levels, a much higher than normal production rate could be expected. The results of analyses given in Table 5 showed that the production rate was a function of market price. In his view the stochastic problem could be solved just as easily as the deterministic problem.In reply to a question by Dr King as to whether the function relating recovery to production rate (Table I) was based on real data, the author replied that it was based on the results of an analysis conducted at the Union Carbide Corporation's Pine Creek tungsten mine in California.Dr D. M. Hawkins stated that costs were incurred when the production rate was altered, for example, in appointing or laying off staff, and that in practice it may be necessary to take these costs into account in finding the optimum production rate. Mr Roman replied that, while normal administrative costs were accounted for, the additional costs incurred in appointing and laying off staff were not taken into account."

Jan 1, 2014

By I. Satola, J. Aromaa

In this work we have reviewed methods to classify corrosivity of ground waters. Weight loss and stress corrosion cracking (SCC) corrosion tests have been done for rebar and steel strand. No clear indication of SCC was found. The application of tensile stress to 85 % of yield strength increased general corrosion rate significantly in very corrosive waters. The effect of corrosion protection on the axial behavior of steel strands was determined by double pipe axial tests with different embedment lengths. The results showed a significant difference on behavior between epoxy-coated steel strands, galvanized steel strands and plain steel strand. Dans la présente étude, nous avons passé en revue des méthodes permettant de classifier la corrosivité des eaux souterraines. Des tests portant sur les pertes de poids et sur la corrosion FCC (la fissuration par corrosion sous contrainte) ont été effectués pour les barres d’armature et les torons. Aucune indication nette de FCC n’a été constatée. L’application d’une contrainte de traction allant jusqu’à 85 % de la limite d’élasticité a accru de manière significative la vitesse générale de corrosion dans les eaux très corrosives. L’effet de la protection contre la corrosion sur le comportement axial des torons en acier a été déterminé au moyen de tests axiaux à double tube avec des longueurs d’enrobage différentes. Les résultats ont mis en évidence une différence significative quant au comportement entre les torons en acier à revêtement époxy, les torons en acier galvanisés et les torons en acier standard. In dieser Arbeit haben wir Methoden geprüft, die korrosive Wirkung des Grundwassers einstufen. Gewichtsverlust- und SCC-Korrosionstests wurden für Stahlstäbe und Drahtlitzen durchgeführt. Es wurden keine sicheren Hinweise auf Spannungsrisskorrosionsbrüche gefunden. Bei Anwendung einer Dehnbelastung von 85 % der Streckspannung bzw.Ergebnisstärke stieg die allgemeine Korrosionsrate in stark korrosivem Wasser deutlich an. Die Wirkung des Korrosionschutzes bei axialem Verhalten von Stahldrahtlitzen wurde durch axiale Tests an Doppelleitungen unterschiedlicher Versenkungslänge determiniert. Die Ergebnisse zeigten im direkten Vergleich von epoxidbeschichteten, galvanisierten und normalen Stahldrahtlitzen beachtliche Unterschiede im Verhalten auf.

Jan 1, 2003

ADVANCES IN EXTRACTION METALLURGY AND REFINING A symposium organised by the Institution of Mining and Metallurgy will be held in London from 4th to 6th October, 1971. Particulars can be obtained from: The Secretary, Institution of Mining and Metallurgy, 44 Portland Place, London WIN 4BR, ENGLAND. ICAMC -71 - HUNGARY The Third International Conference on Automatic Control of Mines and Collieries will be held at Balantsfured, Hungary from 27th to 30th September, 1971. Further particulars can be obtained from: ICAMC - 71, Budapest 3, P.O. Box 115, HUNGARY. AUSTRALIAN INSTITUTE OF MINING AND METALLURGY Illawarra Branch A symposium on "Blast Furnace Injection" is to be held at Wollongong University College from 15th to 17th February, 1972. About 20 papers on various aspects of blast furnace injection will be presented, including two on nonferrous furnaces. Further particulars may be obtained from: N. Standish, Chairman, Symposium Committee, Wollongong University, Australia 2600.

By M. Royle, A. Bloem, R. Uken

Rock mass damage induced by mining increases the fracture frequency and joint aperture width in the pit walls and rock mass behind open pit mine slopes. The depth and intensity of this mechanical damage relative to the pre-mining state is not well understood and yet is a major factor in the development of slope stability models and operational guidelines. The induced damage can be partitioned into domains or zones. The blast damage zone is essentially a ‘free flow’ rock mass volume, which transitions quite rapidly into the excavation damage zone, which extends beyond that. In both zones, transient high in situ water pressures are often linked to unstable slope conditions. Whereas rock damage can enhance passive depressurisation in the rock mass, high infiltration rates on the other hand, as one could expect during rainstorm events, will decrease slope stability within the dilated pit rock mass, especially in the blast damage zone-excavation damage zone, by increasing pore pressures for short periods of time. Ice jacking and freshet are additional factors to consider in (sub) arctic environments and can be exacerbated by unfavorable rock fabric orientation. On a local scale, brittle deformation damage zones, in the form of faults, can contribute to slope instability, or enhanced stability because of slope depressurisation, depending on their location and orientation relative to the pit shape and the water sources. In this study, the shapes of the damage zones and their anticipated impact on infiltration and/or passive depressurisation are considered for different pit morphologies, rock mass conditions, in situ stress, and hydrogeological settings. Some unusual hydrological situations, like mining towards rivers and lakes and the potential effects on pore pressures, are also considered. This investigation has resulted in the development of a method to adjust initial hydraulic conductivity values used to estimate transient pore pressure conditions found in rock masses exposed in different pit morphologies and stress regimes as well as discontinuities’ orientation relative to open faces within the open pit mine. The changes in K values and pore pressures can then be used to determine hydrogeological influence more accurately on future pit slope stability.

Sep 1, 2025

By B. S. Xakalashe, M. I. Khama, Q. G. Reynolds

The carbonaceous reduction of manganese ore is an energy-intensive process that releases large amounts of pollutant gases. In an attempt to circumvent the greenhouse gas emissions, this research investigates hydrogen as an alternative reductant. The reduction of manganese ore with hydrogen results in the structural changes in the intermediate products, which might limit the diffusion of the reactant gases through the pores. Computational fluid dynamics (CFD) models capture the structural changes and predict the rate controlling mechanism and this is key in designing the prereduction reactors. The current work uses CFD models to predict the degree of reduction in a shaft furnace under hydrogen reducing conditions. Manganese ore is described as a collection of scalar and tensor fields such as thermal conductivity of the porous medium, density, and viscous resistance. The results indicate that advection contributes significantly towards the overall transport of hydrogen to the reaction sites. Porosity of the final product was found to be higher than porosity of the raw material.

Mar 4, 2025

By K. Isaac, S. O. Bada

This research focuses on the co-firing of discard coal with refuse-derived fuel (RDF) to utilize this abundant resource in South Africa for energy generation and reduce the volume of waste disposed of at landfills. The potential of a coal with a high ash content (> 40%), which is a grade used in some power stations in South Africa, and its combustion compatibility with two different RDFs in terms of emission reductions has been established. Gaseous emissions and ash residues from the combustion and cocombustion of the coal, two different RDFs and coal/RDF blends of different proportion were analysed. One of the RDF samples contained mostly paper (PB) and the other mostly plastic (PL). Co-combustion ash from the discard coal and RDFs showed a decrease in chloride and alkali metal contents as the coal ratio in the blend increased. The slagging propensity of the co-fired blends was found to be very low, while the propensity for fouling decreased from high to medium for all the blends with < 75% RDF. Cocombustion of RDF with coal showed a decrease in SO2 emissions from 387 ppm (discard coal) to 50 ppm for the sample containing 25% coal discard plus 75% PL. A 15% PL to 85% coal blend also reduced NOx emissions from 145 ppm (100% PL) to 88 ppm. The lowest CO2 emission observed was 6000 ppm for the blend of 85% discard coal plus 15% PB. It was established that the most favourable fuel blend that can produce the lowest sulphur emissions if used for power generation is the 25% coal discard plus 75% PL sample.

Aug 2, 2022

By A. F. Spinks, S. P. Nicholls

"The Lower Orebody at Chingola Division of Nchanga Consolidated Copper Mines, Limited, is a stratified orebody that is mined by a continuous caving system. The accurate determination of the developed and semi-developed ore reserves has always been difficult. The new system proposed in 1971 is designed to update and, as new informa¬tion becomes available, to account for the depletion of, the reserves.There are three main inputs to the system. These are borehole data, survey data and extractions data. The borehole data are input to a geological borehole master file system, which holds every recorded detail of a borehole in an easily extractable form. These data can be extracted for ore reserve calculations or for contour mapping of orebodies and rock types. The grades for use in the ore reserve calculations are extracted from the relevant boreholes.The survey data are information on the position of the blocks and drifts, taken from plans, and information on the scraper drift and trough drive positions taken from sections. The information is extracted from the plans and sections using a D Mac pencil follower. The ore reserve is calculated from the survey data and the borehole data.Data on extractions are taken from scraper operators&apos; logs, tramming records, skips hoisted records and accepted mill tonnages and grades. Using these data, the mill tonnages are reconciled back to the drifts, to deplete the current ore reserves.As new workings are brought into operation and further evaluation holes are drilled, the relevant data are input and the new developed ore reserve is calculated."

Jan 1, 2014

By B. Matsetela, S. Amos, V. Nkuna

"The Kamoa-Kakula copper project—a joint venture between Ivanhoe Mines, Zijin Mining Group Co. Ltd, and the government of the Democratic Republic of Congo—has been independently ranked as the world's largest undeveloped high-grade copper discovery by international mining consultant Wood Mackenzie. It is a very large, near-surface stratiform copper deposit with adjacent prospective exploration areas within the Central African Copperbelt, approximately 25 km west of the town of Kolwezi and about 270 km west of the provincial capital of Lubumbashi. A phased development approach is currently envisaged. The first phase of the project involves the development of a 6 Mt/a underground mine and surface processing complex (dual stream concentrator) at the Kakula deposit, a discovery announced in early 2016. The second phase involves an integrated 12 Mt/a two-stage development, beginning with initial production from the Kakula mine, to be followed by a subsequent, separate underground mining operation at the nearby Kansoko mine, along with the construction of a smelter. Project description and locationThe Kamoa–Kakula project comprises a newly discovered, very large stratiform copper deposit with adjacent prospective exploration areas, located within the Central African Copperbelt in Lualaba Province, Democratic Republic of Congo (DRC). The Kamoa–Kakula project lies approximately 25 km west of the town of Kolwezi and about 270 km west of Lubumbashi. Ivanhoe owns a 49.5% share interest in Kamoa Holding, an Ivanhoe subsidiary that currently owns 80% of the project. Zijin Mining owns a 49.5% share interest in Kamoa Holding, which it acquired from Ivanhoe in December 2015 for an aggregate cash consideration of US$412 million. The remaining 1% interest in Kamoa Holding is held by privately-owned Crystal River.The Kamoa–Kakula project consists of the Kamoa exploitation licences (exploitation permits 12873, 13025, and 13026, which cover an area of 397.4 km2) and one exploration licence (exploration permit 703 covering an area of 12.74 km2). The Kamoa exploitation licences, approved 20 August 2012, grant Kamoa Copper the right to explore for, develop, and exploit copper and other minerals, for an initial 30-year term, expiring on 19 August 2042. The permits can then be extended for 15-year periods until the end of the mine’s life."

Nov 1, 2018

By M. Z. Emad, S. Raza, K. Jalil, M. A. Raza, M. U. Khan, S. A. Saki

Dimension stone mining is Increasing because of growing demand from the building and construction industries. Diamond wire saw cutting is a popular dimension stone mining technique around the world. Estimation of the production cost for this method is critical for these operations. n this research a production cost model was developed for the mining of granite using a diamond wire saw. Cost and production data were collected from a granitic dolerite operation in Pakistan for a 4.5-year period, and analysed to identify the cost components. Fuel (34%), labour (15%), consumables (40%), and maintenance (5%) were found to be the four major cost components in this operation. A regression-based dimension stone production cost model incorporating statistically significant variables was developed. The data presented a strong correlation of production cost with fuel, labour, and consumables costs. Finally, a production cost model based on the consumption cost of diamond wire is presented. The model was verified using actual production cost data, which indicated 95% (R2 = 0.95) variance in the data between the predicted and actual production cost values. The model may help field engineers in computing their dimension stone operational cost during the cutting phase.

Nov 6, 2023

By L. Forbes, G. Forbes, J. Wang

Bubble size measurement is a vital part of flotation system analysis and diagnostics. Over the years, a great many different bubble size analysis tools have been developed. However, all of them rely on ex-situ measurement and in-pulp sampling techniques. This paper evaluates the Mettler Toledo ParticleView™ Measurement probe as a novel method for in-situ bubble size measurement. This device is then compared to the conventional Anglo Platinum Bubble Sizer (StoneThree). It was found that the in-situ bubble size analysis technology appears to be a more user-friendly and reliable option for determining bubble size in flotation. However, the current instrument design is not suited to industrial applications. Keywords: Bubble size measurement, bubble coalescence, PVM probe

Jan 1, 2020

By L. Uotinen, M. Rinne, R. Mishra

Underground mining gives rise to geotechnical hazards. A formal geotechnical risk assessment can help to forecast and mitigate these hazards. Frequentist probability methods can be used when the hazard does not have many variables and a lot of data is available. However, often there is not enough data for probability distributions, such as in the case of new projects. The risk assessment is often subjective and qualitative, based on expert judgement. The purpose of this research is to present the use of Bayesian networks (BNs) as an alternative to existing risk assessment methods in underground mines by combining expert knowledge with data as it becomes available. Roof fall frequency forecasting using parameter learning is demonstrated with 1141 sets of roof fall data across 12 coal mines in the USA. The prediction is nearly identical for individual mines, but when multiple mines are evaluated it is difficult to find a single best fit distribution for annual roof fall frequency. The BN approach with TNormal distribution was twice as likely to fit the observed data compared to the Poisson distribution assumed in the past. A hybrid approach using BN combining multiple probability distribution curves from historical data to predict annual roof fall is proposed. The BN models can account for variability for multiple parameters without increasing the complexity of the calculation. BNs can work with varying amounts of data, which makes them a good tool for real-time risk assessment in mines.

Jun 1, 2021

INTRODUCTION This paper was originally presented at the Platinum Adding Value Conference, held at Sun City from the 4th to 6th October 2004. Narrow reef mining may not be applicable to the base metal operations in Zambia, however, it is considered that the methodology used is equally appropriate to the development of technology and mining methods in mining environments other than narrow reef mining. The purpose of this paper is to explore the integration of technology and stoping systems. For the last hundred years the South African narrow reef mining industry has battled to control working costs in a labour intensive industry. It is only through the application of appropriate technology that change will occur. Stoping systems, because it is the stoping method and methodology that is at the heart of the mining system. Introduce a different technology that results in a more efficient stoping system and the mining system will look after itself. The technology applied to stoping in narrow reef mining, over the last 100 years, can be categorised as follows: ? The introduction of pneumatic rockdrills early this century. The cumbersome rig mounted units being replaced by smaller, lighter, hand held units that were then made easier to use with the addition of an air leg. (The so called Swedish method of mining.) As late as the early 1970s some drilling was still being carried out without the assistance of an air leg. ? Scraper winches to replace gravity and shovels to move rock both in the face and the gullies were first introduced in the late 1920s. ? Hydraulic props installed close to the face and capable of applying force against the hangingwall as well as yielding in a controlled manner under dynamic load arrived in the 1960s. In many instances these have now been replaced by yielding elongates fitted with water hydraulic tensioning devices. ? Some people argue that the introduction of tungsten carbide inserts, to improve drilling, was equally important.

Jan 1, 2005

"This paper challenges the traditional notion that mine planners need to plan production so as to incur the lowest mining cost. For a given mine configuration, a mine that increases its mining rate will incur increased mining costs. In an environment in which operations are fixated on cost reduction, a proposal that increases costs will not be readily accepted. Such a proposal requires financial justification—the increase in costs might be recuperated by the additional production. This paper evaluates the net present value (NPV) across a range of copper prices for two underground orebodies located at different depths, using a production rate of 300 kt per quarter and a scenario that introduces additional equipment and costs for 450 kt per quarter. The evaluation was based on the changes of NPV for the orebody located at a shallow depth compared with the orebody at a greater depth. Discrete event simulation combined with mixed integer programming was used for analysis. Unlike traditional sensitivity analysis, this study re-optimizes the mine plan for each commodity price at each production rate. The results show that, for the low mining rate at the final copper price, an NPV of A$1530.64 million is achieved, whereas an NPV of A$1537.59 million is achieved at a higher mining rate. Even though pushing mining rates beyond traditional limits may increase mining costs, this option may be beneficial at certain commodity prices, particularly when prices are elevated. IntroductionA traditional notion among mine planners is that mining rates should be planned in such a way as to reduce production costs. This concept generally relates to the mining rate that results in the highest machine utilization for the selected equipment. Although an existing mine may consider increasing its mining rate by adding equipment to a given mine configuration, this typically increases mining costs. In an environment in which operations are fixated on cost reduction, a proposal to increase costs may be very difficult to argue for. The value of the mine plan is well recognized as varying with the mining rate for a given orebody (Smith, 1997)"

Jan 1, 2017

By D. Bessinger, J. Rabe, J. Zietsman, C. Coetzee, P. H. Lamont, J. Muller

The UCAR® CHILL-KOTE? freeze lining concept combines wall cooling with carbon and graphite refractories of higher thermal conductivities to ?chill? the refractory lining by transferring heat from the refractory lining. Effective sidewall water cooling, together with the efficiency of the heat dissipating conductive refractories, lowers the temperature of the lining to below that of the molten process materials. This causes a layer of slag and process metal to solidify or ?freeze? and form a protective ?skull? which completely coats the refractory hot face. Once formed, the slag skull insulates the refractories, reducing heat loss and protect the lining from erosion, chemical attack, thermal shock, and other stresses. The result: extended life and greatly improved refractory performance. The Ilmenite smelting process depends on the presence of a solidified slag skull to protect sidewall refractory material from chemical attach by molten slag. No known refractory material is able to withstand this corrosive material. To date, UCAR has not applied their Chill Kote ? technology in the ilmenite smelting industry. This paper revolves around the results obtained from conducting an ilmenite smelting campaign on a 500kW DC open-arc furnace with a UCAR designed refractory system. The purpose of this test was to establish the effects such a lining has on refractory wear and the reduction-smelting process. Proper thermo-couple management enabled the authors to monitor lining wear for the duration of the campaign. Prior to the pilot-scale campaign, modeling work was completed to evaluate the feasibility of applying UCAR® CHILL-KOTE? technology to ilmenite smelting furnaces. The successful operation of a pilot-scale furnace equipped with the UCAR® CHILL-KOTE? lining as well as concise modeling suggest that it should be a viable option to consider for an industrial-scale furnace.

Jan 1, 2007

By J. K. Pothal, S. Basu, R. Barik, P. K. Senapati, A. Dubey

The aim of this paper is to study the characteristics of limestone particles (size varies from 4 mm to 20 mm) during its transportation from open cast mines through pipes. The influence of four different size fractions of limestone samples (4–6 mm, 6–10 mm, 10–15 mm, and 15–20 mm) on pipe flow characteristics during vertical transport in a 100 mm NB hose pipe was investigated. The flow velocities in the vertically lifting pipe was varied from 0.95 m/s to 2.78 m/s and a rotary feeder of 2 to 4 tonne/hr. capacity was employed to feed the limestone samples to the lifting pipe. The pressure drop data for the different size fractions of limestone samples at different mixture velocities were analysed. The effect of input volume fraction and superficial velocity of limestone samples on hold-up ratio were discussed. It was indicated that there was no substantial increase in pressure drop of slurry samples in the studied range of concentrations (CW = 4.22% - 12.54%), particle size, and low to medium range mixture velocities with respect to water run head loss data. The hold-up for the larger size fractions (15–20 mm) of limestone samples was found to be significant as compared to smaller size fractions, which may be due to terminal settling velocities of individual fractions of the studied samples.

Mar 4, 2025

By A. F. van der Merwe, R-D. Taylor, M. Jacobs, F. H. Conradie

Total bound moisture (TBM) is a typical quality indicator of industrial-grade gypsum. This gypsum is comprised of three distinct phases, namely anhydrite, dihydrate, and hemihydrate, of which only the latter is of much industrial use. TBM analysis is a lengthy laboratory procedure, and an artificial neural network (ANN) TBM inference measurement is proposed as a fast and online alternative. An ANN inference model for gypsum TBM based on plant data was developed. The inputs to the network were primarily focused on the plant's calciner, and different network topologies, data divisions, and transfer functions were investigated. Furthermore, the applicability of the TBM value as a quality indicator was investigated based on a gypsum phase analysis. A strong correlation between TBM and the gypsum hemihydrate and anhydrite content was found, validating the plant target TBM of 5.8% as a quality indicator. A network topology consisting of one hidden layer with logarithmic-sigmoid (logsig) and pure linear (purelin) transfer functions showed the best performance (R > 90%).

Oct 3, 2023