Search Documents

By J. R. Thoenen

This circular is part 3 of the third paper (entitled "Excavation") of a series summarizing the technical problem; involved in the production and preparation of sand and gravel. Part 1 discussed the use of power shovels, draglines, and excavator cranes. Fart 2 discussed the use of power scrapers, slackline cableway excavators, and hydraulic monitors. This circular discusses the use of the hydraulic, clamshell, ladder, and dipper dredge. Part 4 to follow will discus the use of haulage equipment, and subsequent parts will discuss the application of both excavating and haulage equipment to various types of deposits. HYDRAULIC DREDGE Judged by the number of installations and the tonnage produced, as recorded in part 1 of this circular, the hydraulic or pump dredge is the most popular type of underwater sand and gravel excavator.

Jan 1, 1935

By James D. Noll, Jon A. Hummer, Shawn E. Vanderslice, Aleksandar D. Bugarski, George H. Jr. Schnakenberg, Steven E. Mischler, Larry D. Patts

The National Institute for Occupational Safety and Health designed and conducted a study in an underground metal mine to assess the effects of selected diesel emissions control technologies on the concentrations of diesel particulate matter and gases in underground mine air. The control technologies studied included diesel particulate filter (DPF) systems, filtration system with disposable filter elements, diesel oxidation catalytic converter, and biodiesel blends. Each technology was tested on a mining vehicle operated in an isolated area of an underground mine supplied with fresh air. These isolated zone tests allowed for the operation of vehicles under conditions and over duty cycles that closely mimic actual duty cycles of production equipment. The DPF systems reduced the elemental carbon (EC) concentrations in mine air between 88% and 99%. The same systems reduced total particulate matter (TPM) concentrations in mine air by approximately 75%. The biodiesel blends B20 and B50 caused a reduction in the EC concentrations of 26% and 48%, respectively. Those blends also reduced TPM concentrations by 9% and 24%, respectively. The use of #1 diesel fuel reduced EC concentration by 13% compared to #2 diesel fuel. An increase in nitrogen dioxide concentration of up to two times was seen when platinum-catalyzed DPF systems were tested.

Jan 5, 2006

By E. S. Shedd

Amenability studies were conducted by the Federal Bureau of Mines on an electrooxidation technique for the extraction of mercury from cinnabar ores, particularly those that are too low in grade to be furnaced or retorted economically. Oxidation was accomplished by electrolysis of the ore while slurried with brine. Mercury was dissolved through the formation of the soluble tetrachloro mercury complex, HgC142-. Mercury extractions ranged from 90 to 98 percent in 4 to 6 hours of processing time when tests were made on eight different types of cinnabar ores containing from 0.7 to 18 pounds mercury per ton ore. Salt concentration was varied from 4 to 10 weight-percent depending on whether Pb02 anodes and iron cathodes were used or whether graphite was used for both electrodes. Power consumption ranged from 17 to 64 kilowatt-hours per ton of ore treated. Ninety-nine percent of the mercury was recovered from pregnant solutions by precipitation on an active metal such as zinc, followed by distillation of the resulting amalgam at 600° C.

Jan 1, 1975

This Bureau of Mines report reviews the information presented at the Sixth Mineral Waste Utilization Symposium cosponsored by the Bureau of Mines, U.S. Department of the Interior, and the IIT Research Institute. Environmental scientists and engineers from nine countries participated in the symposium, which was held May 2-3, 1978, at the Chicago campus of IIT Research Institute. The 56 papers presented on the reclamation and recycling of mining and mineral wastes, municipal solid waste, industrial wastes, and scrap metal are summarized herein.

Jan 1, 1980

By T. J. Driscoll

Methane-air mixtures can ignite as a result of sparking or rubbing of materials, particularly by impact involving light alloys and rusted steel where an exothermic thermite reaction can occur. This report reviews the published literature and describes a new method utilized by the Bureau of Mines for studying the processes occurring during collisions of light metals with rusted steels. The method involves measuring the spectra of sparks and explosions in methane-air mixtures using a photodiode array. Initial results obtained using magnesium and aluminum alloy 6061-T651 projectiles striking rusted steel are reported. These results indicate that the continuous parts of the spectra show a larger intensity for incendive sparks compared with nonincendive sparks, with the largest relative change in the higher energy, ultraviolet region. An unexpected shift of the intensity maximum for the continuous parts of the spectra towards the infrared region was observed for the more incendive sparks. Evaluation of rusted steel samples with electron microscopy, energy-dispersive X-ray spectrography, and Auger electron spectroscopy after they had been impacted by aluminum alloys indicated that aluminum was transferred to the steel in the form of islands that became larger as a function of increasing projectile velocity.

Jan 1, 1982

By Virgil A. Marple

The objective of this contract was to investigate time-integrated and real-time methods for determining the diesel exhaust particulate concentration in underground mines, in particular, coal mines. The microorifice uniform deposit impactor (MOUDI) is recommended for obtaining the time-integrated measurement of the size distribution. The mass concentration of diesel exhaust particles can be obtained from the particle size distribution of mine aerosols. On a mass basis, diesel exhaust particles are primarily in the submicrometer size range while coal dust particles are larger. Size distribution measurements made in the laboratory and in three underground coal mines exhibited two distinct modes with the diesel exhaust particles in the smaller particle mode and the coal particles in the larger particle mode. The point of separation between the two modes occurred in the 0.7 to 1.0 pm size range. The separation was found to be independent of mass fraction of the diesel exhaust particles, particle concentration and sampling site. Methods recommended for further consideration as real-time monitors of diesel exhaust aerosols in mines are photometers and filter pressure drop techniques. A preclassifier would be required in both cases to separate the larger dust particles from the sample. The Metrex Mineral/Diesel Photometer should also be investigated further once the electronics problems are eliminated.

Jan 1, 1986

By L. F. Heising

This report is a general summary of pertinent data on the manufacture and use of synthetic ammonia products. It provides a condensed summary of the potentialities of a synthetic ammonia industry in North Dakota for Federal, State, and private organizations that may be interested in helping to develop an integrates synthetic ammonia and fertilizer industry. The report contains discussions of: (1) Materials used in the manufacture of nitrogenous fertilizers, nitric acid, and urea; (2) National production, imports, exports, and consumption; (3) the ammonia industry, location, capacity of plants; (4) processes used in manufacturing synthetic ammonia, nitric acid, and urea; (5) other potential industries; and (6) analyses of manufaturing and plant cosh;. Additional information on industrial compounds from ammonia and plant nutrients removed by crops is given in Appendixes 1 and 2. Synthetic ammonia is one of the primary ingredients in fertilizers. Resources required in synthetic ammonia manufacture are available in North Dakota. Hydrogen is available from the petroleum and natural gas resources, particularly in the Williston Basin, and from the large lignite resources in the State. Hydrogen can be produced from lignite by a gasification process developed by the Bureau of Mines at Grand Forks, N. Dak.

Jan 1, 1954

By B. H. Clemmons, C. H. Schack

Extractive metallurgy techniques currently employed to recover silver from primary ores and secondary scrap were reviewed and evaluated to identify and delineate metallurgical problems whose resolution would increase the supply of silver from domestic materials. The survey revealed that practically all primary silver is recovered by froth flotation concentration of various types of ores, followed by smelting and refining of the separate lead, copper, and zinc concentrates. Silver losses during the complex processing are, with rare exception, inconsequential. Furthermore, any silver production gain from base metal ores, which contribute about two-thirds of the total primary silver, is directly dependent on improvement in the market for the base metals. Statistical data on new and old silver scrap are wholly inadequate to make reliable conclusions about scrap processing problems and the possibility of increasing the recovery of silver from the many forms of secondary silverbearing materials. The available information indicates (1) that efficient silver reclamation practices are employed by the larger users of silver, and (2) that recovery of additional secondary silver involves solution of problems of collection rather than of processing. Several possibilities exist for limited increases in silver production from primary ores by improvement in metallurgical practices. Specifically, research is needed to (1) solve the problem of recovering silver from the copper ores of the Copper Range district, Michigan; and (2) devise economically feasible methods for recovery of silver from presently marginal or submarginal ores that because of grade, location, and frequently complex nature cannot presently be exploited by conventional techniques.

Mar 1, 1965

By D. R. Dolinar, A. T. Iannacchione

Limestone formations in the United States can be subject to relatively high horizontal stresses owing to the existence of tectonic loading of the limestone strata. Underground limestone mines use the room-and-pillar method, in which 12- to 18-m-wide rooms are typically excavated. The stability of these excavations can be compromised by the horizontal stress, resulting in a rock fall hazard. Rock falls are the cause of 15% of all reportable injuries in underground limestone mines. Horizontal stress related damage can occur in the form of guttering along one or more sides of an excavation, roof beam buckling or oval shaped roof falls, with the long axis perpendicular to the major horizontal stress. Numerical analyses show that the pillar layout and orientation of the mine workings has an effect on the horizontal stress distribution within the roof. The effects of high horizontal stresses can be mitigated by orienting the heading development direction parallel to the maximum horizontal stress, reducing the number of cross-cuts and off-setting the cross-cuts to limit the potential lateral extent of horizontal stress related roof falls. The modeling approach described in this paper can be used as a tool to evaluate potential roof failure and optimize the stability of room and pillar layouts.

By Jeffrey Johnson, Carl Sunderman, Ted Williams, Stephen Signer, Douglas Bayer

To measure the loading behavior of friction bolts, researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) installed strain gauges on the interior of friction bolts and developed a battery-powered miniature data acquisition system (MIDAS) that fits inside the hollow portion of the friction bolt. The advantages of this system are that it is protected from face blasts and eliminates the need for external wiring. Laboratory pull-out tests showed that friction bolts installed in a concrete block with resin were loaded to about 1.8 tons/ft of bolt length; bolts installed without resin were loaded to 1.3 tons/ft. Three strain-gauged friction bolts were installed at Hecla Mining Company’s Gold Hunter Mine, Mullan, ID, in the wall or rib of a mechanized cut-and-fill stope. The object of these tests was to establish an installation procedure for the bolt-and-MIDAS combination and to evaluate performance. The stope was advanced in three 15-ft increments and strains induced in the rock bolts by stress changes in the rock were recorded every 30 minutes. The MIDAS proved to be rugged enough to withstand the shock and vibration from nearby (5 ft) face blasting. Data from MIDAS showed that the friction bolt installed with resin was the most sensitive to each face advance. It showed a steady increase in loading to a maximum value of 1000 microstrain. The friction bolt installed without resin showed stick-slip behavior with loads to a maximum of 400 microstrain before the stope was completed.

By Walter D. Holland

This instructors guide is intended for use in a course which teaches metal and non-metal mine inspectors to perform surveys for inhalation contaminants in above ground metal and nonmetal mine work areas. The handbook entitled "Handbook for Surveys of Inhalation Contaminants in Above Ground Metal and Nonmetal Mining and Processing Work Areas? is used as a manual during the course. The manual contains a survey check list, rules for determining if sampling is required, a list of most frequently encountered contaminants, a list of candidate contaminants and their sampling conditions, and a description of control procedures and devices. There are several experiments in this guidebook which the trainees perform to acquaint them with the sampling systems.

Jan 1, 2011

By R. E. Heithecker

In Kansas, almost every oil well drilled into a limestone formation is treated with hydrochloric (muriatic) acid upon completion. This is done to increase the potential capacity of the well and thereby increase its "daily allowable" production (see p. 9 ), to shorten the time required to produce the recoverable oil, and to increase the quantity of oil recovered ultimately from the reservoir. The porosity and. permeability of limestone formations seldom are uniform throughout the proved area, consequently the production capacities of completed wells vary considerably. Acid treatment of wells tends to increase production capacity and to equalize potential capacity. If offset wells already have been treated with acid, new wells usually are treated to protect the property on which they are drilled against drainage. Even though competitive conditions do not exist in a field, it

Jan 1, 1939

By J. M. Davidson

The potassium mineral polyhalite (K2SO4.MgSO4.2CaSO4.2H20) found in large deposits in western Texas and southeastern New Mexico is associated with varying amounts of halite (sodium chloride, NaCl) and anhydrite (calcium sulphate, CaSO4). Although the anhydrite, because of its low solubility and slow rate of solution, is relatively inert, the halite is dissolved immediately in any process solution with which the polyhalite comes in contact. Limited quantities of sodium chloride in the liquors used for the hot extraction of polyhalite materially improve the results obtained,4 but only a very small sodium chloride content may be desired in the entering polyhalite in other procedures, such as Bureau of Mines process 75. In. all of the processes suggested for the recovery of potassium sulphate from polyhalite the control of the sodium chloride content will be desirable, if not absolutely essential to efficient operation. OCCURRENCE OF HALITE IN POLYHALITE A preliminary estimate of the amount of halite associated with typical deposits of polyhalite may be derived from drill cores, although it should be remembered that only 50 or 60 core tests have been made in the many hundreds of square miles of the Permian basin. From a mineralogical study of 41 of these cores, Schaller and Henderson6 state: In many of the sections of core that seem when viewed by the unaided eye to consist essentially of polyhalite, both halite and anhydrite are present in greatly varying quantities - with very minor quantities of clay and magnesite.

Jan 1, 1934

By John C. Machisak

THIS INFORMATION CIRCULAR contains injury and employment data for all stone quarries in the United States for the Calendar year 1960. This publication contains statistical data on injuries and employment pertinent to the stone quarries and related operations, such as the manufacture of cement and lime, rock dressing etc., but excludes statistics for clay and sand and gravel operations. Data for these commodities may be found in other Bureau publications. Reports received from the operators are voluntary responses to the Bureau's request for information; therefore, the figures may not be complete for the industry. However, since these data contribute greatly to the promotion of safety, every effort has been made to make them representative of the industry.

Jan 1, 1963

By John C. Machisak

THIS INFORMATION CIRCULAR contains injury and employment data for all stone quarries in the United States for the Calendar year 1960. This publication contains statistical data on injuries and employment pertinent to the stone quarries and related operations, such as the manufacture of cement and lime, rock dressing etc., but excludes statistics for clay and sand and gravel operations. Data for these commodities may be found in other Bureau publications. Reports received from the operators are voluntary responses to the Bureau's request for information; therefore, the figures may not be complete for the industry. However, since these data contribute greatly to the promotion of safety, every effort has been made to make them representative of the industry.

Jan 1, 1963

By Ruth F. Brinkley

This circular describes the activities and publications of the Bureau of Mines, Explosives Research Laboratory4 for the fiscal year 1960 (July 1, 1959 -June 30, 1960). Part 1 describes briefly the principal projects that were active during the report period, and presents some data not scheduled for publication elsewhere in the near future. Certain of the results are only preliminary and should be regarded as tentative, pending the findings of the completed investigation. Publications that appeared during the report period are listed and described briefly in part 2. In general, the research activities reported in these publications antedate fiscal year 1960. The published material relating to activities that are still current is indicated by references in part 1.

Jan 1, 1962

By L. M. Irwin

This Bureau of Mines investigation relates the physical properties of copper reverberatory furnace slags to changes in composition, The smelting of upper Michigan copper ore presents some problems that probably differ from those of other copper smelting areas. The study of these problems has, however, provided important data regarding slags in general and therefore will be of value to other operations as well. Conclusions reached from this study were: (1) Slag fluidity and refractive indices varied directly with the iron content and inversely with silica, lime, and alumina, and (2) there was no apparent correlation between slag fluidity and its copper content.

Jan 1, 1962

By W. K. Overbey

The Bureau of Mines conducted surface joint and stress measurements, airborne remote sensing imagery studies, compass-oriented borehole televiewer surveys, numerical simulation of fractured wells, and well productivity studies in a four-quadrangle study area of Ohio, to determine the effects of earth fracture systems on the deliverability of gas storage fields. The results of these studies indicate that much useful information about a gas storage reservoir can be obtained and put to practical use by studying--(1) oriented cores for fractures and directional permeability, (2) orientation of induced hydraulic fractures for alignment of well patterns, and (3) aerial photos and multispectral scanner imagery for general surface geology comparison and to determine if some, development patterns can be generated by such results. The absence of known tectonic elements associated with flat-lying sediments, such as faults or fracture zones that can be seen on the surface, indicates that the use of remote sensors such as radar or aerial photography is not likely to be useful in picking well locations for drilling. Studies similar to those discussed here should be conducted in gently folded and strongly folded sedimentary formation areas to determine if the increased knowledge of earth fracture systems under these conditions might be beneficial in gasfield and gas storage reservoir development.

Jan 1, 1974

By Alvin Kaufman

To aid industry and Government in planning water developments the Bureau of Mines in 1963 canvassed mineral producers to determine water use in 1962. Water use by the mineral industry comprises only 2 percent of the water withdrawn by industry as a whole. The major water-using mineral industries are natural gas processing, phosphate rock, sand and gravel, and iron ore. Analysis indicated the following conclusions: 1. Total water use and new water intake is dependent on the quantity of material processed and the process water requirements of the particular industry or commodity. 2. Recirculation is dependent on the processing requirements of a particular commodity, the manner in which the water is used, cooling and condensing requirements in certain large industries, the quality of new water intake, and the need to treat new and discharged water. 3. Consumed water is dependent on the quantity of water recirculated, the temperature and humidity in the area, and the proportion of water used for cooling and condensing. 4. A threefold increase in water use by the mineral industry by 1985 is forecast.

Jan 1, 1966

By W. M. Dressel

This Bureau of Mines report describes a shaft closure demonstration project in which 11 inverted pyramid-shaped plugs were used to plug abandoned open mine shafts in Galena, KS, The inverted pyramid-shaped forms, fabricated from steelplate, were designed so that the inverted base would be larger, by 4 ft on a side, than the approximate size of the shaft opening at the surface residuum-solid rock interface. After the surface openings of the shafts were trimmed with a backhoe, the steel forms, complete with reinforcing, were lowered into the openings and filled with concrete; the remaining portions of the openings above the plugs were backfilled to slightly above the surrounding surface level with waste rock and soil. Location and elevation monuments were installed for long-tern evaluation of the success of the project.

Jan 1, 1985