Search Documents

By G. L. Barlett, J .. D. Barry

Supernatant media of dust-exposed pulmonary alveolar macrophages (PAMs) were inactive in assays for both Interleukin-1 and fibroblast growth factors (FGF). We have begun to evaluate several factors that may interfere with dust-PAM interactions. To determine the effect of sterilization on the activity of dusts, PAMs were exposed to autoclaved dust, heat-sterilized dust or to dust that had not been heated. Supernatants from the first two groups were inactive in the FGF assay, but supernatant from PAMs exposed to unheated dusts stimulated growth of lung fibroblasts. Recent data have revealed that freshly crushed mineral dusts possess labile free radicals that are absent in dust that has been stored for more than a few days. Suspensions .were prepared of a "stale" sample of anthracite dust 867 and of a freshly ground sample of the same dust. These suspensions were instilled intratracheally into guinea pigs under general anesthesia. Two, five or eight days later, PAMs were collected from the lungs by bronchoalveolar lavage, and the cells were counted. At two and five days after instillation, all lavage suspensions contained 70 to 85% PAMs, of which 5 to 18% contained phagocytized dust particles. On day eight there were again 80-84% PAMs in all suspensions, but in the presence of "fresh'" dust, 48% of PAMs. had phagocytized particles in comparison to 16% in the presence of '"stale'" dust. A similar experiment was performed in short-term cell culture. During 24 hours, >95%. of PAMs phagocytized dust particles, whether or not the dust was "stale" or '"fresh". Our studies are being extended to determine the effect of (1) removing surface oil contaminants by organic extraction and (2) suspending dusts without surfactant.

Jan 1, 1988

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

D. 1 Most Effective Salts A. Ammonium Phosphates Monammomium phosphate and diammonium phosphate (salts of ortho phosphoric acid) are superior to the triammonium salt in fire-resisting properties. Of these two, the monammomium salt is chemically the more stable. It is also held very retentively by a number of woods, thus reducing leaching out of the salt if exposed to water. Saturated aqueous solutions of mon- or di-ammonium phosphates have vapor preservatives corresponding to an atmospheric relative humidity of 9Z to 93 percent, the wood, will, therefore, not attract any moisture at humidities below this figure. Low concentrations (1 lb dry fire-retardant per cubic foot of the dry, treated timber) will stop flame and high concentration (5 lbs. per cubic foot) will prevent smoldering. B. Ammonium Sulphate In low concentrations ammonium sulphate has only a small effect on flame propagation, but its effect is marked when concentrations of the order of 20 percent are employed. It has no appreciable effect on smoldering. It is more corrosive to metals than are the phosphates, but is less corrosive than ammonium chloride or magnesium chloride. It is possible to leach it out of wood by prolonged and continuous action of water The vapor pressure of the saturated solution corresponds to 81 percent atmospheric humidity.

Jan 1, 1976

By Jon C. Volkwein

The industrial sand industry has been exploring new techniques to reduce dust. One company was experimenting with adding water during bagging operations to the surface of the hag, and into the product as it flowed into the bag. The Bureau of Mines, using instantaneous dust sampling instruments, measured the effectiveness of three methods of adding water. Results indicated that various types of water sprays applied in carefully controlled amounts could reduce dust up to 50% at worker locations at the bagging machine and inside a railroad boxcar. This report also discusses constraints such as product handling, customer acceptance, cold weather problems, dust collector performance, and other areas.

Jan 1, 1981

By S. A. Ferguson

Purpose: Marras et al. developed a technique to evaluate sincerity of effort during dynamic trunk motion performance. The validity and reliability of the technique have not been evaluated. Therefore, the objective of this study was to first determine whether or not a sincerity of effort measure correctly identified those giving a sincere effort in a blinded randomized control trial and second to quantify inter-rater and test-retest reliability. Methods: This article reports the findings of a two phase study. In phase one, the blinded evaluation, participants were randomly assigned to either a sincere or insincere performance condition. An examiner tested participants without knowledge of the participant's group membership. In the second phase, two examiners evaluated each participant twice to quantify inter-rater and test-retest reliability. Results: In the blinded phase the specificity was 100% and sensitivity was 90% for identifying sincere and insincere effort, respectively. Phase two results showed no significant difference in probability of sincere effort between raters or between testing sessions. Conclusion: A performance criterion that accurately identifies sincere vs insincere group membership during functional evaluations was identified. There were no significant differences between raters or between testing sessions. These findings indicate that this test is reliable and possesses good predictive validity in assessing sincerity of effort.

Jan 1, 2003

By Forrest T. Moyer

General injury experience in the mineral fuel industries was less favorable in 1965. Of the major industry groups, the coal mining and the coke industries had higher injury-frequency and severity rates than in 1964. The oil and gas industries had an increased Tate of occurrence of injuries although the severity rate improved. However, in the relatively small peat and native asphalt industries, the injury experience was more favorable than in 1964. Overall operating activity for the mineral fuel industries, as measured by the average number of men working daily and the total worktime, was higher than in 1964. Moderate declines in employment and worktime in the coal and peat industries were more than offset by gain in the other groups. In addition to the industry classifications included in this chapter, similar injury, employment, and worktime data on the metal, nonmetal, stone and aggregate industries are presented in volume I. Corresponding data for broad classifications of mineral industry groups arc given by States in volume III of the Minerals Yearbook.

Jan 1, 1967

By Harold W. Lipper

HELIUM shipments in 1963 exceeded the volume shipped during the previous year for the 14th successive time. Shipments from Bureau of Mines plants were 627.3 million cubic feet, an increase of 5 percent over the volume shipped in 1962. Production from Bureau of Mines plants totaled 774.2 million cubic feet. The Bureau purchased 1,420 million cubic feet of helium in the helium conservation program and stored it underground for future use. Each of the five plants, financed and built by private industry for helium conservation, made deliveries during the year. Helium continued to playa key role in space, atomic energy, defense, and other research programs. Additional capacity for liquefying helium became available, and the first civilian helium-cooled nuclear-powered reactor in the United States began pre-operation testing.

Jan 1, 1964

By H. W. Frevert, A. C. Fieldner, S. H. Katz

"The Bureau of Mines, in its investigations of as masks for use in mines and allied industries tests masks that are voluntarily submitted by manufacturers for examination, and issues approval certificates for masks that meet the bureau's specifications. This paper describes the tests that were conducted on an ammonia gas mask by the Bureau of Mines, which successfully met all requirements and tests for ammonia, masks. The mask tested, known as the GMD ammonia gas mask, is manufactured by the Mine Safety Appliances Co., Pittsburgh, Pa. This ammonia gas mask, which forms a pocket over the face and allows breathing through the nose, consists of a face-piece with non-shatter eyeglasses; this is attached by means of a corrugated rubber tube to a canister supported on wearer's chest by a harness. The canister is green in color and is of tinplate construction. It was a disc valve at the bottom to prevent exhalation through the canister. The filling of the canister consists of a specially impregnated activated charcoal, about 750 c.c. in volume and weighing about 520 grunn. The material is supported above the check valve by a dome of wire screen covered with toweling. Above the granular material is a filter of absorbent cotton screens, and all materials are hold firmly in place by pressure from strong"

May 1, 1926

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

RECOMMENDATIONS FOR FURTHER WORK Based on the development effort and full-scale tests conducted during this program, a number of technical areas for future research and development have been identified. Further work in these areas would help to improve the reliability, speed of operation and efficiency of the remote sealing system. Recommendations for future work are summarized as follows 1. Development of an Inert Gas Generator For the sake of expediency in conducting the field test program, fresh air was used as the fluidizing medium for the fly ash. However, in an actual mine fire application the use of fresh air is likely to be prohibited. An inert gas, such as nitrogen, carbon dioxide or air containing less than 8 percent oxygen would be required. Using combustion as a means of reducing the oxygen content of air appears to be an attractive solution to the generation of the high flow rates of gas required (2500 to 5000 scfm). Such an inert gas generator would serve a dual purpose for the overall fire extinguishing operation. First, it would provide the inert gas for fluidizing the fly ash. Second, it could be used for inerting the fire area after the seals had been placed, thereby reducing the time required to extinguish the fire. It is recommended that the Bureau undertake a program to develop a field-operable, inert gas generator to satisfy these two requirements. 2. Development of a Field-Operable Sonar Initial Probing System A first stage prototype of a sonar initial probing system was developed during this present program. The results obtained with

Jan 1, 1973

By R. Karl Zipf

Use of Salamon's stability criterion in underground mine design can prevent the occurrence of catastrophic domino-type pillar failure. Evaluating the criterion requires computation of the local mine stiffness and knowledge of the post failure behavior of pillars. This paper summarizes the status of the practical use of this important criterion and suggests important research to improve our capabilities. Analytical and numerical methods are used to compute the local mine stiffness. Work to date in computing local mine stiffness relies mainly on elastic continuum models. Further work might investigate local mine stiffness in a discontinuous rock mass using alternative numerical methods. Existing post failure data for coal pillars are summarized, and a simple relationship for determining the postfailure modulus and stiffness of coal pillars is proposed. Little actual postfailure data for noncoal pillars are available; however, numerical models can provide an estimate of post failure stiffness. Important factors controlling postfailure stiffness of rock pillars include the postfailure modulus of the material, end conditions, and width-to-height ratio. Studies show that the nature of the failure process after strength is exceeded can be predicted with numerical models using Salamon's stability criterion; therefore, a method exists to decrease the risk of this type of catastrophic failure. However, the general lack of good data on the postfailure behavior of actual mine pillars is a major obstacle. Additional back-analyses of failed and stable case histories in conjunction with laboratory testing and numerical modeling are essential to improve our ability to apply the stability criterion.

Jan 5, 1999

To reduce equipment operator exposure to respirable dust in enclosed cabs by examining the effectiveness of retrofitting air pressurization and filtration systems on existing cabs.

Jan 1, 2001

To permit better cap lamp positioning for users of dust helmets. Approach The present design of the dust helmet prevents use of the miner's cap lamp when the front shield is raised, When the shield is raised I the cap lamp is directed at the mine roof or back, making the lamp useless in the event the miner needs to wear his self-rescuer. A flip bracket was designed by the Bureau of Mines to correct this situation. How It Works The safety hat is modified by the addition of lamp clips, a bracket and a hinge on the cap lamp and face shield. Two clips hold the lamp cord firmly to the helmet. When the safety hat shield is raised, compressive force from the lamp cord causes the cap lamp hinge to swing open about 90%, allowing the lamp

Jan 1, 1984

Provide the technology to remotely reset circuit breakers on continuous mining machines used in extended cuts.

Jan 1, 1994

Reduce exposure of longwall face workers to respirable dust generated during the advancement of roof supports. Approach Identify and implement current water-application and improved support-movement practices used to lower support-generated dust. Defining the Problem Bureau studies have shown that on some longwall faces support dust can contribute over 30 percent of the respirable dust exposure of face workers. Conditions contributing to high levels of respirable dust generation during support movement are: depth of cover greater than 1,000 ft; immediate roof consisting of coal top or friable shales; and face-air velocities in excess of 500 fpm. Moreover, at most longwalls, supports are advanced on the intake-air side of the shearer as it travels with the airflow. This places the shearer operators, and in many cases the support movers, downwind of support advance, thus increasing their respirable dust exposures.

Jan 1, 1984

By C. R. Kindall

Recently 30 men wore viewing the demonstration of a now portable electric arc-welding outfit. A few hours later 17 of the 30 men reported to the doctor for treatment. They were suffering from traumatic conjunctivitis. In two cases the gain was very severe and the symptoms were similar to those of iritis. orphine had to be administered to afford relief from pain. Only two men of the 30 wera not affected in some way from this exposure. These two men were thick-lensed orange-colored glasses. Several of the men wore orange-colored glasses with thin lenses, but the latter were not heavy enough to afford protection.against an exposure as long as took place. The distance of the eye from the are also in- fluences the possibility of injury. Conjunctivitis is an inflammation of the con- junctiva; the conjunctiva is the mucous membrane covering the inside of the eye- lids and part of the eyeball. Traumatic conjunctivitis is caused by foreign bodies in the eye, exposure of the eyes to high winds, dust, smoke, intense light from electric arc lamps, and from electric welding apparatus. In the instance mentioned above, the inflammation was due to the ultra-violet rays. The ultra-violet rays lie beyond the violet rays in the spectrum and are invisible to the eye. In some cases the effect is so severe that, in addition to conjunctivitis, an inflammation of the skin similar to sunburn is produced. The symptons of conjunctivitis caused by intense light or by the ultra- violet rays are marked photophobia (abnormal intolerance to light), excessive secretion of tears, intense starting of the lid, contraction of the pupil, some- times swelling of the lid, and small ulcers developing on the eyeball or cornea. Unless properly treated by a physician immediately, chronic inflammation of the conjunctiva, cornea, iris, or retina, and possibly blindness, may result. Under proper treatment most cases get wall in a few days. All treatments should be under the direction of a physician. That usually advised is to place ice packs on the patient's eyes three or four times daily. The pack should be left on from 15 minutes to an hour. The eyes should be irrigated with normal salt solution (a teaspoonful to a quart of sterile vater) or a saturated solution of boric acid several times daily. If there is a discharge of pus, a few drops of a 25 per cent solution of argyrol or a 5 per cent solution of protargol should bo placed in the eyes three to six times daily. The patient should be confined to a darkened room until his condition improves in order to avoid complications. These treatments will reduce the swelling, give the patient confort, and prevent the development of chronic conjunctivitis. In severe cases it may be necessary to administer morphine to relieve the pain.

Oct 1, 1920

By Clyde E. Williams

The Northwest experiment station of the Federal Bureau of Mines , at Seattle , Wash . , was established in December , 1916 , and is one of 13 mining experiment stations maintained by Act of Congress , under the direction of the bureau , in the various sections of the country . Under the terms of the organic Act (March 3 , 1915 ) , the province and duty of these experiment stations is to cake investigations and disseminate information with a view to decreasing waste and improving the efficiency in the production , treatment , and utilization of mineral substances . The investigations carried on at the Northwest experiment station attempt to cover the needs of the mineral industry of the States of the Pacific Northwest and of the coastal regions of Alaska . The most in ortant needs of this district are for work on coal washing , electrometallurgy , and ceramics . The electrometallurgical investigations are not necessarily limited to the Problems of the Northwest , but may be of general application . Problems other than those specified above are referred to other stations of the Bureau that specialize on the particular type of investigation required . The Northwest station closely cooperates with the State of Washington through the University of Washington and with the State of Oregon through the Oregon Bureau of Mines and Geology . The University of Washington at Seattle has donated the use of an entire building , which houses the station's administrative offices and chemical laboratory , and parts of two other buildings which are usea in conducting the experimental avestigations . Twenty-five thousand dollars is expended annually by the Federal Government , while the State of Washington each biennium appropriates $ 20,000 , and the State of Oregon from time to time appropriates various amounts for the conduct of work along cooperative lines . Also , the station cooperates with private organizations tht have problems similar to those in which the station is interested . For example , the Washington Electrochemical Co. is cooperating in the electrometallurgical research, and furnishes part of the supplies and technical assistance required .

Mar 1, 1922

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

TEST DECK - ALTIMETER SURVEY WITHOUT ALTMETER TEMPERATURE CORRECTION 1 BAS 8: 22 1391 1391 53. 49.

Jan 1, 1977

To provide a practical method to reduce hand and arm injuries during roof bolting operations.

Jan 1, 2000

By Staff

This Bureau of Mines report is devoted to descriptions of investigations pertaining to underground mine trailing cables, their handling, splicing, and the use of couplers.

Jan 1, 1979

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

A computer program has been developed to simulate evacuation of a mine in case of fire in the following, the capabilities, operations and structure of the program are described with illustrative examples to demonstrate usefulness of using the program. A detailed description of the program with sufficient information to make use of the program appears in Appendix B.

Jan 1, 1976

The NIOSH Office of Mine Safety and Health has released communication products about flyrock safety in the form of informational brochures, flashcards, and toolbox talk materials. Both the mining and construction industries are targeted with these helpful communication tools. These new products can be used as refresher training for employees and as introductory safety materials for onsite visitors.

Dec 1, 2006