Search Documents

Develop a metal substitute which is more plentiful and less expensive than the metals currently being used in high performance, permanent magnets, while maintaining the quality of the magnet. The New Alloy The rare-earth metal used in most high performance magnets is samarium, an expensive metal of limited availability. Cobalt is also used in high performance magnets, but supplies of this metal also are limited because it is not domestically mined and must be imported. The Bureau of Mines embarked on research to find a less costly domestic: metal source for use in industrial magnets. The alloy found most promising consists of mischmetal, a relatively abundant, naturally occurring mixture of rare-earths, which can be used as a replacement for samarium. Additives of copper, magnesium and iron used in combination with mischmetal aid in replacing some of the cobalt needed for the magnets.

Jan 1, 1983

By J. O. Winget

Amino acids were investigated in conjunction with rare-earth separation by ion exchange to determine whether they can be utilized effectively as retaining agents for metals separation using ethylenediaminetetraacetic acid (EDTA) eluant at 85° to 90° C. Hydroxyethylethylenediaminetriacetic acid (REDTA) and diethylenetriamine pentaacetic acid (DTPA) were the most effective amino acids investigated. Elements of atomic numbers 39 and 57 through 68 were effectively retained, whereas elements of atomic numbers 69 through 71 passed through the retaining-agent band. Utilization of REDTA or DTPA retaining agents allows an increase of 75 percent in the EDTA eluant concentration over that possible with hydrogen-or copper-retaining ions without precipitation occurring. Eighty-five percent recovery of the EDTA eluant collected before rare-earth breakthrough and during elution of lutetium, ytterbium, and thulium, and essentially complete recovery of the REDTA or DTPA retaining agents, are possible without extensive processing.

Jan 1, 1968

By Maria I. De Rosa

Table 19 and figure 7 show the number of fires and fire injuries for surface coal mines by state during 1990-1999. Table 19 also shows by state the risk rates, employees' working hours, lost workdays, and coal production. For surface coal mines, 215 fires occurred in 21 states during 1990-1999. Ninety-four of those fires caused 93 injuries and I fatality (the yearly average was 21.5 fires and 9.3 fire injuries). Fourteen fires and seven injuries involved contractors. The Ewhr value was 729 x 10° hr (In = 0.026), the CP value was 6,355 x 10° st (Fn = 0.034), and the LWD value was 8,141. Kentucky had the most fires and fire injuries (45 fires and 23 injuries), followed by Pennsylvania (33 fires and 14 injuries), West Virginia (25 fires and 14 injuries), and Indiana (20 fires and 8 injuries). Among these states, Pennsylvania had the highest fire risk rate value (Frr=0.145), while Kentucky had the highest injury risk rate value (In 0.041).

Jan 1, 2004

By Gregory J. Chekan

As part of the initial investigation and validation of a new boundary-element formulation for stress modeling in coal mines, the underground stresses and displacements at two multiple-seam coal mines with unique stress problems were modeled and predicted. The new program, LAMODEL, calculates stresses and displacements at the seam level and at requested locations in the overburden or at the surface. Both linear elastic and nonlinear seam materials can be used, and surface effects, multiple seams, and multiple mining steps can be simulated. In order to most efficiently use LAMODEL for accurate stress prediction, the program is first calibrated to the site-specific geomechanics based on previously observed stress conditions at the mine. For this calibration process, a previously mined area is "stress mapped" by quantifying the observed pillar and strata behavior using a numerical rating system. Then, the site-specific mechanical properties in the model are adjusted to provide the best correlation between the predicted stresses and the observed underground stress rating. Once calibrated, the model is then used to predict future stress problems ahead of mining. At the two case study mines, the calibrated models showed good correlation with the observed stresses and also accurately predicted upcoming high stress areas for preventive action by the mines.

Jan 5, 1999

By Louis D. Dornetto

The effects of electric shocks on man are an important factor in the design of power systems and protective devices. The current levels just below let-go and just prior to the onset of ventricular fibrillation must be known and taken into consideration in the design of power systems and protective devices. Isolated (ungrounded) electrical distribution systems are compared with resistance and solidly grounded systems. The advantages and disadvantages of each are discussed and recommendations are made. Transients on coal mine power systems are a problem that, until recently, have been ignored. Transient voltage levels that can be expected on both the high and low side of the load center and the effects of transients on electronic equipment and personnel are covered.

Jan 1, 1975

By J. E. Murphy

Field freezing was used by the Bureau of Mines to effect the redistribution of the components in a cerium-12.5-atomic-percent-iron alloy. The application of the electric field caused the iron to migrate toward the anode. A field intensity of 0.04 v/cm and a current density of 240 amp/cm2 were used. The conditions that yielded the greatest redistribution of alloy components were a small thermal gradient along the specimen (from 5° C/cm to 10° C/cm) and a very slow freezing rate (0.15 cm/hr). Under these conditions it was possible to process specimens of ½ -inch diameter as compared with the capillary-size specimens used by most previous investigators.

Jan 1, 1968

By M. MacLaughlin, J. Whyatt

A case study is presented that relates statistical descriptions of joint sets to the distribution of local wedge failures along the crest of a catch bench at the Yellowstone Talc Mine. The fracture sets and bench width were mapped by teams of geological engineering students from Montana Tech under the direction of Dr. Mary MacLaughlin. The students analyzed the fracture data, conducted physical property tests, and used a beta version of a NIOSH program “Bwedge” to predict the distribution of surviving bench widths. In the course of this analysis the students developed evidence of software performance issues that, unfortunately, frustrated their analysis. These have now been addressed and a full analysis completed. The analysis confirms the validity of the student mapping program and provides insight into the effects of blasting and excavation practices on the bench. It also provides a tool for exploring the pattern of bench crest failure that would result from variations in both bench geometry and blasting practices.

By John Ward Smith

The Bureau of Mines derived equations expressing the theoretical relationship between density of oil-shale rock and its organic content. Effects on theoretical shale density produced by variations in mineral composition and organic matter properties were evaluated. The theoretical relationship was extended to relate oil-shale density to oil yield in both oil weight and volume units by considering the fraction of organic matter converted to oil and the specific gravity of the oil produced. Corollary equations relating organic content by volume to organic content by weight and to oil yield were developed. The general relationships apply to an oil-shale deposit uniform in character. Application of the theoretical relationships to Green River Formation oil shales was demonstrated.

Jan 1, 1969

This study presents a reservoir modeling approach to investigate the relative effects of different coalbed parameters on the migration of methane into development entries. A base coalbed reservoir model of a three-entry development section, where grids were dynamically controlled to simulate the advance of mining at a constant section advance rate, was created and calibrated for a Pittsburgh Coalbed mine in the Southwestern Pennsylvania section of the Northern Appalachian Basin. The values of coalbed parameters were varied to evaluate their effects on predicted methane emissions for various development distances. The results of these parametric simulations were then used to derive linear expressions relating these parameters to methane emissions into the workings. These models were analyzed to assess their significance and adequacy for predictive purposes. This work shows that coupling reservoir simulations with linear modeling yield a technique that can be applicable to different coalbeds. The reservoir parameters used by the linear models (coalbed thickness, pressure, sorption time constant, Langmuir parameters, permeability) can be determined by running relatively simple laboratory tests, such as adsorption equilibrium and permeability determination, on coal samples obtained either from the mining operation or from the exploratory boreholes drilled ahead of mining.

Jan 1, 2008

By Charles C. Hwang

In this Bureau of Mines report, a previously developed theory of reverse stratified flow in ventilated duct fires is applied to mine-related ventilation systems that utilize an exhaust fan to supply the forced airflows. The coupling between a fire and the ventilation airflow in a single-entry duct is analyzed to relate the air velocity in the absence of a fire to air velocity during a fire. By combining the derived coupling equations with the results of the previously developed theory of reverse stratified flow, it is possible to calculate critical flow velocities required to prevent reverse stratified flow in the event of a duct fire. The sample calculations shown agree with the few experimental results available from small-scale tunnel fires.

Jan 1, 1978

By Charles Findlay, Stephen Krickovic

A methane emission rate study was conducted in 1969 on a longwall section of a Lower Kittanning coalbed mine in central Pennsylvania. The longwall face was mined with a drum shearer between developed headings on the head end and headings on the tail end that were driven with a ripper-type continuous miner as needed. The study was conducted over 22 consecutive shifts (7-1/3 days). The average methane emission rate from the Lower Kittanning coalbed during mining at the face and developing the headings at the tail end of the face was 34 cfm. Caving of the gassy overlying strata as the result of mining at the face increased the methane emission to rates ranging from 702 to 1,049 cfm.

Jan 1, 1971

By W. F. Hughes

The thermodynamics of an electromagnetic field-fluid interaction system is discussed. A review of the thermodynamics of linear media (the permittivity and permeability taken as functions of density and temperature) is presented; then an extension is made to nonlinear media (the permittivity and permeability taken as functions of the fields). Expressions for thermodynamic properties and reversible work are derived and the first law of thermodynamics for magnetohydrodynamic flow is discussed.

Jan 1, 1968

By Howard E. Parkinson

Since 1969, the Department of Interior, Bureau of Mines, has carried out communications research. Research has been directed toward developing emergency and nonemergency mine communications. This paper gives an overview of the progress made in the last two years. Particular emphasis is given to the overall program, noise and signal measurements, systems studies, guidelines, products, and demonstrations now being carried on in operating mines.

By M. J. Ferrante

Relative enthalpies of cuprous iodide (CuI) were measured at the Bureau of Mines to provide thermodynamic data for the advancement of min-eral technology. Enthalpy measurements between 298.15 and 1,396.3 K were made with a copper-block drop calorimeter. The temperatures of transition were measured by differential scanning calorimetry (DSC). Reversible transitions were determined at 643 K with a standard enthalpy of transition [(6Htr)] = 0.74 kca1/mol, at 679 K with a [6Htr = 0.65 kca1/mo1, and at 868 K] with a standard enthalpy of fusion [(6H~) = 1.895 kca1/mol.] Tabulated values are listed at selected temperature increments from 298.15 to 1,600 K for the standard relative enthalpy (HO -H298), heat capacity (CpO), entropy (SO), and Gibbs energy function [-(Go -H298)!T]. The enthalpy data are also given in the form of equations and combined with thermodynamic data from other investigations to derive values of standard entha1pies of formation [(~HfO)], Gibbs energies of formation [(6GfO)], and logarithms of the equilibrium constants of formation (log Kf).

Jan 1, 1987

By Charles Vaught

This paper discusses the fact that US coal mining organisations are losing the knowledge they need in order to be able to respond to emergencies. The authors note that knowledge management provides a useful perspective from which to view the problem, but that the debate about what constitutes knowledge should be broadened to include a debate about what constitutes management. It is argued here that knowledge is actually shared knowing distributed across group members; that such knowledge can be managed by cultivating it; and that narrative is the medium through which this may be done. The paper then examines NIOSH research that has attempted to use such an alternative knowledge management approach to help potential mine emergency responders better deal with the predicaments they are likely to encounter on-site.

Jan 1, 2006

By Oscar Lee

"Flotation is generally regarded as a process that is only applicable to metallic minerals. However, its scope is now known to be greater than this, because some of the nonmetallic minerals are floatable, such as graphite, sulphur, and fluorite. Recent observations show that limestone may be added to the list of floatable nonmetallic minerals. Such work is being done on a laboratory scale at the Southern Experiment Station (Tuscaloosa, Ala.) of the Bureau of Mines, Department of Commerce, where experimental magnetic concentration of the low-grade iron ores of the Birmingham district is in progress. Certain experiments have demonstrated that the limestone may be floated from the magnetic log-washer tailing, and then incorporated in the iron concentrate.If the loss of lime could be prevented, some ores though low in iron and high in insoluble contain enough lime to make their concentrates self-fluxing. Since this loss in the magnetic log-washer can not be avoided, the Time must be recovered from the tailing by some method and added to the magnetic iron concentrate before sintering. Then the resulting concentrate will be self-fluxing.While seeking a suitable means of treating the tailing for recovery of lime, flotation was tried. It was at once evident that this method had possibilities, during the early part of the investigation, soap solution made from a common soap was used as a flotation reagent. The froth obtained was a fairly good lime concentrate. This result was an important clue, and led to tests with the use of such reagents as oleic acid and sodium oleate. Later, cresol, creosote, coal tar and other similar flotation reagents were tested in combination with the oleic acid and soap solutions. As a result, oleic acid and cresol used together were found to be satisfactory.The tailing from the magnetic log-washer is in excellent physical condition fur flotation. The iron ore had been ground in a ball mill to 100 mesh for magnetic concentration. Hence the bond between the lime carbonate and the other constituents of the tailing was well broken."

Apr 1, 1926

By Stephen P. Signer

This paper presents an overview of laboratory and field tests on approximately 250 fully grouted roof bolts instrumented with strain gauges in order to study loading behavior. Laboratory work included pull tests, time-dependent tests, and shear tests. The field tests were conducted in 14 different mines extracting different commodities. However, because of the focus of this publication, only the results of tests in 9 coal mines are reported here. In the field tests, all but 14 bolts were loaded by rock movement; these 14 bolts were tested using pull gear. The variables studied included anchorage length, mechanical interlock, time-dependent behavior, shear, installation load, loading rate, and maximum load level. Such information will improve the understanding of the behavior of resin-grouted bolts, which in return will enhance the safety of miners by reducing the occurrence of rock falls. The influences of geology, overburden depth, entry width, mining-induced stresses, and bolt spacing are not described.

Jan 10, 2000

By Todd M. Ruff

A training software package for new mine employees, called Miner Training Simulator (MTS), has been developed by researchers at the National Institute for Occupational Safety and Health. MTS is a computer-based tool that allows a trainee to enter a simulated mine and interact with his/her surroundings in order to learn basic mining concepts, safety procedures, mine layouts, and escape routes. The training simulator software and instructions for its use are described in this report. Also, each mine using the software will have different requirements with regard to safety training. To customize the simulator for these differences, an interpreted scripting language is used to define interactions between the trainee and the virtual mine and objects in it. The scripting language, called Tool Command Language, uses simple commands to control various actions in the simulation, such as sounds, safety messages, hazards, and movement of objects. The basics of the scripting language are described here, along with many examples and instructions for building a script for MTS.

Jan 6, 2001

By Gordon L. Kinney

Following a year of great uncertainty, the political situation in Bangladesh improved during 1976. The major problem for Bangladesh remained the high birth rate and crowded conditions. Bangladesh had the highest population density of any agrarian country--over 80 million people in a land area of 144,000 square kilometers, 65% of which is considered arable. The Government, with considerable foreign assistance, was actively encouraging voluntary family planning, and set a growth rate target of 2% per year or less. However, even if the growth rate was reduced to the target level immediately, the population of Bangladesh would nevertheless nearly double within 20 years.

Jan 1, 1980

By E. Morrice

The effect of the temperature of SmF3-LiF electrolyte on the electrolytic preparation of samarium-cobalt alloy by the consumable cathode technique was investigated. The temperatures of the cathode zone, alloy collection zone, and samarium oxide (Sm203) feed zone had to be controlled carefully to obtain a satisfactory samarium-cobalt alloy product. Any appreciable deviation from certain temperature values adversely affected yield and product quality.

Jan 1, 1971