Search Documents

By Rad B. Langston, Ted J. Williams, John A. Marjerison, Rimas T. Pakalnis, Tom M. Brady, Doug C. Bayer, Mark J. Bren

Underhand cut and fill mining methods are used at the Lucky Friday, Stillwater, and Galena mines in the western US in an effort to safely mine in difficult ground conditions and as a primary mining method where access below the ore is limited. The method has evolved at each mine to meet the unique situations associated with their milling procedure and mine layout. Details of the operational aspects of the backfilling and mining cycles at each mine are presented in this paper, accompanied by a summary of the mechanical properties of the backfill and its in-situ geomechanical behavior.

By James S. Browning

The Bureau of Mines conducted laboratory and small-scale continuous tests of kyanite ore from Georgia to determine the technical feasibility of recovering commercial-grade kyanite concentrates by flotation. The research indicated that combinations of sulfuric acid and petroleum sulfonate may be used effectively for flotation of kyanite from quartzite-kyanite ore. Over 87 percent of the kyanite was recovered in a concentrate analyzing 55.8 percent A1203 and 5.3 percent acid-soluble Fe203. Subsequent treatment of the flotation concentrate by high-intensity wet magnetic separation reduced the acid-soluble Fe203 to 0.8 percent and increased the alumina content to 57.6 percent, with a recovery of 82.7 percent of the total alumina in the ore.

Jan 1, 1970

To cost-effectively reduce noise and vibration in newly manufactured mantrip vehicles. Approach Previous Bureau of Mines research demonstrated that noise controls could be in-stalled on existing mantrip vehicles, thereby substantially lowering noise levels inside the mantrip. Under Bureau sponsorship, a manufacturer of mantrip vehicles agreed to incorporate similar noise controls into a new vehicle during manufacture. Throughout this project, durability, maintainability, and cost were considered to be as important as noise reduction. How It Works The following noise-control features were included in the new mantrip: (a) Suspension Isolation- The suspension components were isolated by inserting elastomeric materials between them and the vehicle frame.

Jan 1, 1982

By John C. Machisak

THIS CHAPTER of the Minerals Yearbook (Volume III) contains overall employment and injury experience for coal mines-bituminous, lignite, and anthracite; coke, petroleum and natural gas; and peat and slag plants; metal and nonmetal mines; sand and gravel operations; stone quarries; metallurgical plants, including metal mills and smelters; and nonmetal mills for 1959. Volume I of the yearbook contains injury experience and employment data in the metal, non-metal, sand and gravel, slag, and quarrying industries, and the milling operations and related plants. Volume II contains the injury experience and employment data in the fuel industries--coal, coke, petroleum and natural gas, and peat. Surveys conducted by the Bureau of Mines were the source of injury and employment data used to compile the tables and furnish information for the accompanying text. Response to the surveys was voluntary except that for coal mines. The Coal Mine Safety Act requires operators of coal mines to furnish the information requested.

Jan 1, 1960

By Alan H. Goode

The advancement of high-temperature drilling fluid technology for application in geothermal environments is part of the Bureau of Mines program for more efficient development of our Nation's energy resources. The bentonite constituent of water-base drilling fluids is sensitive to destabilization by high-temperature and salinity. A substitute material for bentonite, phosphate slime, which is reported to be saline resistant, was considered. These studies show that spray-dried slime suspensions have more favorable rheological behavior, but poorer filtration properties, as compared with bentonite suspensions.

Jan 1, 1975

By Thomas V. Falkie, R. Venkataramani

The purpose of this work was to Investigate the rate at which coal is delivered from the underground working face by gathering arm type loaders as employed on continuous mining machines, to identify the factors - geometrical , geological, mechanical, or procedural - which affect the delivery rate, and to develop quantitative rate-descriptive equations for the loading function. The mathematical techniques employed were factor analysis and multiple linear regression. It was determined that the coal-cutting function of the continuous mining machine is the factor that primarily Influences the loading function The geometrical factors -the dimensions of the work area In relation to the dimensions of the mining machine -were the factors of secondary influence. Fifty-five percent of the experimental variation in the loading function was explained in terms of the six most prominent Independent variables. It is expected that this work will be useful In operations-research studies as applied to underground coal mining, and with refinement will enable mine planners to select equipment based on the operating characteristics of the equipment and the mining conditions.

Sep 1, 1972

By C. M. Frost

Crude shale oil produced by gas combustion retorting of Green River oil shale was hydrocracked over a cobalt molybdate catalyst at operating pressures of 500, 1,000, 1,500, and 3,000 psig, an operating temperature of 8900 F, and a liquid hourly space velocity of 1.0. Hydrogen feed rate was maintained at 6,000 scf/bbl. The volume-percent yields of total liquid product were directly proportional to the operating pressure. Weight-percent conversion and volume-percent yields of gasoline were directly proportional to the log of the operating pressure. Catalyst deposit percentages were inversely proportional to the log of the operating pressure. Nitrogen and sulfur removal rates as well as saturation of the liquid products increased as the operating pressure was increased.

Jan 1, 1973

By Thomas V. Falkie, R. Venkataramani

The empirical nature of this investigation required measurements of variables under operating conditions in underground coal mines. The variables to be measured were based on the postulated character¬istics of the loading function, as described in the previous chapter. One class of variables presumed to influence the loading function are geological variables. Accordingly, the sites for data collection were selected in different bituminous coal seams at dispersed locations in order that variation in geological conditions would exist. Seven mines in central and western Pennsylvania and one mine in northern West Virginia were selected as data collection sites. Five different coal seams were represented by these mines. The remaining classes of variables - geometric, mechanical, and procedural - were measured as they occurred in the mines. A description of the measurements, and the conversion of these measurements to forms which could be-analyzed for effect on the loading function is given. Mining Dimensions At the underground working face, the following dimensions were measured: a. Thickness of coal excavated. b. Thickness of shale excavated. c. Total height excavated. d. Width excavated. e. Depth of penetration of each machine cut. With the exception of the last of these dimensions, all were measured

Jan 1, 1972

By John C. Machisak

THIS CHAPTER of the Minerals Yearbook relates to employment data and injury experience in the metal, nonmetal, and quarrying industries. Combined statistical data on the mineral industries as a whole can be found in volume Ill. Each industry in the chapter is shown separately, and no attempt has been made to combine and show an overall picture. The voluntary reporting of data on injuries and employment by operators of metal and nonmetal mines and quarries has contributed substantially to the promotion of safety in these industries. Data on injury and employment in the clay mining and milling industry are included for the first time. Table 6 contains data for clay mines only for 1955 and for clay mines and mills for 1956. The clay-mill figures are included with other nonmetallic mills in table 5. The information for norunetallic mills was compiled and published for the first time in the 1955 issue of this report.

Jan 1, 1958

By Jeffrey Johnson, Thomas Brady, Radford Langston, Mary MacLaughlin, Hendrik Kirsten

The magnitudes and directions of in situ stresses affect the stability of mine openings, as well as the type and amount of ground support needed to maintain a safe working environment for miners. Using hollow inclusion stress cells, researchers from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health obtained two in situ stress measurements from the face of two footwall lateral drifts at the Stillwater Mine near Nye, MT. The first measurement, obtained in 1997, was collected under the valley beneath the Stillwater River. The second measurement was obtained in 2002 under the main frontal massif of the Bear tooth Mountains in the western sector of the mine. Although few data are available, the major principal stress under the valley has been recorded as nearly horizontal in a north-south direction perpendicular to the ore body, while beneath the mountains, stress runs east-west parallel to the ore body. This paper documents the measurements, describes the in situ stress state, and discusses a finite-difference analysis of the biaxial test.

By P. W. Jeran

The Beckley mine is one of five new mines in a heretofore unmined portion of the Beckley coalbed. The remoteness of these new mines from prior mining and their greater overburden preclude applying methane emission experience obtained in the old mines. Four sections of the Beckley mine were monitored. The data gathered show that variations in methane emission cannot be explained by variations in coal production. Although overburdens varied by as much as 30 pct, no correlation with methane emissions could be determined. The rib emissions increase with increased length of rib from a section advancing into virgin coal and do not decline over a prolonged idle period (32 days) whereas some decline has been measured for a section not mining into virgin coal. The indication is that degasification prior to mining will reduce the hazard of methane emissions in this area of the Beckley coalbed.

Jan 1, 1977

By J. J. Bourquin, S. H. Katz

"Three types of respiratory apparatus namely, gas masks, hose masks, and self-contained oxygen-breathing apparatus - are now commonly used for protection from noxious gases, vapors, and smokes or ristes, but no particular type can be selected as best for all conditions. Many factors must be considered in connection with each situation, so that each must be considered as a problem in itself. Following are concise statements for comparing the types:Gas masks are the simplest and easiest to wear, also the least cumber-sore; but they protect only in comparatively low concentrations of noxious gases and should never be used where the air contains less than 16 per cent of oxygen. Special masks give protection from one gas or class of gases, but may give no protection against another gas or class of gases.Hose masks protect in any irrespirable atmosphere, but are somewhat cumbersome, the length of hose limiting the distance a wearer may go from fresh air. They are serviceable also where a supply of pure air moves with the wearer, as where a locomotive engineer in a smoky tunnel is using a hose mask supplied with air from the compressed air line of the locomotive. Hose masks consume no chemicals or materials and so are not limited in the time they may be used.Self-contained oxygen-breathing apparatus protect in any irrespirable atmosphere, but their weight is cumbersome, they can be used only by trained men, and frequent attention must be given them to maintain good working condition. On the other band they are the only safe means for exploring mines and other places filled with irrespirable gases in high concentrations."

Jun 1, 1923

By J. Brad Seymour, Mark K. Larson, Richard L. Rains, Douglas R. Tesarik

For several years, researchers from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) have been using geotechnical instruments in underground mines to study ground control problems and develop means of reducing accidents and fatalities caused by ground falls. This paper describes many of the different types of instruments, sensors, and data acquisition equipment that have been used for these studies; briefly explains the advantages and disadvantages of various sensor technologies; provides practical recommendations regarding the use of specific instruments and data acquisition systems; and outlines a general approach to the design and implementation of a successful instrumentation plan. A wide variety of instruments are commercially available for measuring deformation, strain, stress, and/or load. If used correctly, these instruments can provide important quantitative information regarding the mining-induced behavior of the host rock, the performance of ground support systems, and the safety and stability of underground workings. Data collected from these instruments can warn mine staff of impending ground control failures or hazardous working conditions, as well as provide valuable information for the design of ground support systems and the configuration and sequencing of mining excavations. We hope that the practical information presented in this paper will encourage a more widespread use of geotechnical instruments in underground mines and lead to reliable measurements that aid the engineering decisions affecting the safety of miners.

Jan 10, 2000

By Maria I. De Rosa

The major fire and fire injury findings for all coal mining categories for 1990-1999 are reported in tables 37-38. Table 39 and figure 13 show the number of fires. fire injuries, risk rates, employees' working hours, and coal production (under- ground and surface coal mines only) by time period for all coal mining categories. Table 40 shows major findings (for under- ground coal mines only) for 1978-1992. For all coal mining categories, 458 fires occurred during 1990- 1999; 157 of those fires caused 164 injuries and 2 fatalities (Ewhr = 2,070 x l0%r, Irr = 0.016: C'P (for underground and surface coal mimes only) - 10,363 x l0\t, Frr = 0.044, LWD = 14,753). Twenty-nine fires and 17 injuries involved contractors. Sixty-six fires required firefighting interventions by mine rescue teams (25 times in underground mines) and fire brigades and fire departments (at least 41 times at surface coal operations). In all, 51 fires destroyed or heavily damaged equipment (including 16 pieces of mobile equipment) because of failure of other firefighting methods, late fire detection, undetected fires, or fire size. A total of 114 fires were detected late, and 42 fires were undetected. The greatest number of fires and fire injuries occurred at surface coal mines; the highest risk rate values were also calculated for this category. For all coal operations, the ignition sources that caused the greatest number of fires were flame cutting/welding spark/slag/flames (1 03 fires or 23% with 69 injuries), hydraulic fluid/fuel sprayed onto equipment hot surfaces (98 fires or 2 1 % with 29 injuries), spontaneous combustion/hot coal (62 fires or 14%), electrical short/arcing (49 fires or 11% with 18 injuries), and conveyor belt friction (3 1 fires or 7% with 6 injuries).

Jan 1, 2004

By J. E. Emmerling

The Federal Bureau of Mines investigated dust suppression obtained with three different water-spray nozzle systems during underground continuous coal mining at the face. The nozzles were the "regular" nozzle normally used by the mine, and high-efficiency and low-efficiency nozzles selected on the basis of an airborne capture theory of respirable dust by spray drops. The high-efficiency nozzle used one-third less water than the others throughout the testing. Results depended on the type of cutting operation at the face. The sump-downshear operation appeared to involve a significant amount of capture of airborne respirable dust. The same amount of dust was measured when using the high-efficiency and regular nozzles. The dust levels when using the high-efficiency nozzle were about 20 pct less than those measured when using the low-efficiency nozzle. The sump-upshear operation seemed to involve a predominance of other aspects of dust suppression, such as impaction of spray drops onto the face. Compared with the downshear operation, there was a significant reduction in dust levels for a total face operation when using the regular nozzle; dust levels when using the regular nozzle were about 15 pct lower than those measured when using the high-efficiency nozzle.

Jan 1, 1975

By Kevin Connor

During 1984, minerals exploited in Burundi included gold, kaolin, lime, and peat. Over 1,100 troy ounces of gold was extracted and traded during the year as a result of the lifting of the Government ban on gold mining in mid-1983 and the establishment of an artisan mining program and licensed trading counters. Almost 2,000 tons of kaolin was mined for the manufacture of insecticides. Lime production was for domestic fertilizer applications. Amoco International and the Government signed an accord late in the year for a petroleum exploration program covering 600,000 acres of Burundi's onshore Ruzizi Plain and part of northeastern Lake Tanganyika. Amoco was expected to begin the exploration program by mid-1985. Anticipated program costs could run as high as $200 million.2 The Finnish company Ekono Oy completed its peat industrial energy development studies for the Buyongwe peat deposits of northern Burundi by the end of the year. The project assessed the quantity and fuel quality of 13,000 hectares of peatland and was part of a larger study for developing the Musangati lateritic nickel deposits of Burundi, estimated at 3% of the world's reserves of nickel. The Buyongwe peat would fuel dryers and an electrical generating plant for supplying power to nickel ore processing facilities. Briquetted peat would also be used as a substitute for wood and charcoal, presently the main sources of rural energy in the country and rapidly depleting because of deforestation. The study also evaluated the most economical methods to harvest the peat bogs. The study was financed by the International Development Association (IDA), United Nations Development Program (UNDP), Finnish Aid-Finnida, and the Burundi Government.

Jan 1, 1986

Coal is a combustible, carbonaceous, sedimentary rock that is formed by the accumulation, compaction, and physical and chemical alteration of vegetation [Simon and Hopkins 1981; Bates and Jackson 1987]. Coal is classified according to its type, grade, and rank. The type of coal relates to the plant materials from which the coal originated. The grade of coal refers to the purity of the coal-or the amount of inorganic material (including ash and sulfur) left after the coal is burned [Bates and Jackson 1987; Stefanko 1983]. The rank of coal indicates its degree of metamorphosis and roughly correlates to the geological age of the coal or the geological environment from which it has been mined [Bates and Jackson 1987]. Rank also indicates the percentage of carbon in dry, mineral-free coal [Whitten and Brooks 1973] and the degree to which the coalification process has progressed [Larsen 1981]. The geological process of coalification begins with organic materials (e.g., celluloses, lignins, and other plant compounds that are deoxygenated and then dehydrogenated) and ends with coal of various geological ages, from lignite to anthracite [Larsen 1981]. Table 3- 1 presents the American Society for Testing and Materials (ASTM) classification of coals by rank. According to Parkes [1982], high-rank coal includes anthracite and semianthracite coal ("hard coal," with 91% to 95% carbon); intermediate-rank coal includes low-, medium-, and high-volatile bituminous and sub-bituminous coal ("soft coal," with 76% to 90% carbon); and low-rank coal includes lignite (with 65% to 75% carbon or less). The rank of coal tends to increase from the western to the eastern United States, with anthracite occurring primarily in eastern Pennsylvania [Schlick and Fannick 1971]. Most of the coal currently mined in the United States is bituminous [Given 1984]. A classification of the coal in the United States is provided in Table 3-2.

Jan 1, 1997

By R. V. Ramani, C. B. Manula, A. Owili-Eger

This report was prepared by The Pennsylvania State University under USBM Contract No. G0111808. The contract was initiated under the Coal Mine Health and Safety Program. It was administered under the technical direction of DMRC, with Mr. G. R. Schottler acting as the technical project officer. Mr. J. A. Herickes was the contract administrator for the Bureau of Mines. These applications were developed initially as a part of the instructional material for the course Mng 422, "Mine Ventilation and Air Conditioning" at the Department of Mineral Engineering, The Pennsylvania State University. This ventilation simulator was developed under contract from the Department of Environmental Resources, formerly the Department of Mines and Mineral Industries, Commonwealth of Pennsylvania.

Jan 1, 1975

By N. Kumar Kittusamy, Richard E. Miller

This field study evaluated a newer and older dozer at a construction site. Both dozers performed similar activities in the same location within the construction site. Two operators participated in this study. One operator used the older equipment and the other operator used the newer equipment. Jolting and jarring measurements were taken at the seat/operator interface and at the floor of the cab. The result of this field study indicates that the newer dozer was better than the older dozer.

By Thomas P. Meloy

"This paper presents an interim progress report on our recently begun research project on respirable dusts. We are reporting on a sophisticated, predictive, probably correct, testable hypothesis that postulates a mechanism by which some natively cytotoxic respirable size mineral particles, such as kaolin, are not harmful to the lungs, while other equally cytotoxic particles, such as quartz, are, even in small quantities, very harmful. In essence the hypothesis predicts that some mineral particles, not normally present in the earth's ambient dust, causes the lungs dust defense mechanisms to turn on the lung and harm it. However fruitful the hypothesis may be, it is a hypothesis and much work remains to be done before it can be accepted as a theory.While I may make the presentation and be the PI, my co-PI, Dr. William Wallace of NIOSH, has and will continue to make at least as much contribution to the project as I. Our sophisticated hypothesis is deeply scientifically based and unfortunately, in spite of the multifacited aspects of this project, there is virtually nothing in the literature to guide our work. This means we must go back to the classical physics to develop the models for calculating the powerful electrical effects near particle edges, and we must measure the fundamental biological constants associated with pulmonary macrophage. While there are daily discussions on Boltzman distributions, Einstein's Brownian Motion paper, the Nernst Equation, and sophisticated semi- in vivo biological time constant measurements, we are aware that this is not an easy problem and we are not likely to have irrefutable closed solutions to these problems by next Monday morning.HypothesisLet me now turn to our hypothesis. In order to occupy all the naturally occurring surface areas on the earth, man, during his long evolution from fish, had to evolve effective defenses against all the naturally occurring cytotoxic rcspirable mineral dusts. For example, clays, which are often the main component in naturally occurring respirable mineral dusts, are quite cytotoxic but do not harm the lung. However, for respirable mineral dusts that contain significant amounts of nonnaturally occurring but equally cytotoxic quartz and asbestos particles, the body has not had to evolve- an effective defense mechanism, and thus respirable mineral dusts containing these particles may harm the lung. Our hypothesis is, therefore, that a few nonambient minerals such as quartz, cause the bodies dust defensive system to harm the body in a manner analogous to Lupus or MS, diseases of the immune system."

Mar 1, 1989