Search Documents

By David E. Siskind

The Bureau of Mines performed a comparative study of nine sites at eight surface coal mines to determine if the presence of near-surface underground abandoned workings resulted in the generation of adverse long-duration, low-frequency blast vibrations. Six of the nine sites had underlying workings, and two had thick layers of low-velocity unconsolidated surface material. Extended seismic arrays were used to identify the vibration characteristics within a few tens of feet of the blasts and also as modified by the propagating media at distances over 1 mile. Production blasts and specially fired single-charge blasts allowed the determination of natural ground frequency and the influence of initiation delay timing. Vibration amplitudes from the production blasts at all sites exceeded historical norms, particularly at the greater distances. This contrasts with the near-normal results from single-charge blasts. Apparently, between-hole time delays were insufficient to separate vibrations from adjacent charges for the low-frequency waves present. Single-charge tests showed that the propagating media produced low-frequency, ground-roIl-type surface waves at nearly all sites. Large blasts at such sites could produce an unacceptable risk of vibration-induced cracks in nearby structures.

Jan 1, 1989

Develop a method of dewatering ultrafine mineral waste that will increase water recovery from the waste and produce a dewatered material that eliminates the need for large settling ponds. Background In the hydrometallurgical treatment of many ores and concentrates to recover mineral values, slurries of fine particles are generated. Some of these slurries settle slowly and are difficult to dewater. This inherent property causes environmental and handling problems for the minerals industry. Examples of such problem wastes are clay wastes generated during the mining and beneficiation of phosphate ores, the processing of coal to produce a low-ash material, the cleaning of bentonite, beneficiation of potash, and the recovery of mica from clay-containing ores. At the present time these waste slurries are treated by techniques such as impoundment, thickening, and thickening followed by filtration. But factors such as new environmental regulations, the loss of mineral values in the waste slurries, the need to recycle water in the processing facility, and the lack of land suitable for impounding the waste have shown that new technology will be needed in the future to handle waste slurries.

Jan 1, 1986

By D. W. Frommer

Laboratory mineral-dressing investigations were conducted on talc-bearing samples from Arkansas and Texas under the Bureau of Mines program of examinations and surveys, which is concerned, in part, with the improvement of conservation and utilization of domestic mineral resources. Two of the soapstones in question were successfully upgraded by flotation, utilizing stage additions of a frother and an amine to promote their talc content. The process could enable the producers to meet more rigid specifications of higher priced talc commodities. INTRODUCTION Talc is an industrial mineral with distinctive properties, such as softness, smoothness, large surface area in relation to mass, chemical inertness, and good retention as a filler, that make it particularly valuable to a number of industries. Sales to 6 industries -ceramics, paint, insecticide, rubber, roofing, and paper -consumed 84 percent of the domestic production of talc, pyrophyllite, and ground soapstone in 1952. Mine production in that year totaled 600,908 tons. Sales of crude and ground material were 593,147 tons valued at $11,347,317.2/

Jan 1, 1956

Maintain good blowing face ventilation while taking deeper cuts with a radio-remote, scrubber-equipped miner. Approach A six week in-mine study of face ventilation effectiveness was made by comparing the existing MSHA-approved blowing curtain setback distance of 25 ft with brattice set back distances of up to 50 ft. Effectiveness was determined by measuring methane levels at the face and in the immediate return. How It Works Blowing ventilation systems are commonly used in mines because the high velocity air stream created by these systems rapidly mixes with and dissipates methane generated during the cutting of coal. A drawback to blowing ventilation is that the work area is placed in return air and this may create dust compliance problems for the shuttle car and mining machine operator. To clean dust from the return a number of mining machine manufacturers supply dust scrubbers built into the machine. Dust-laden air is drawn into ducting at the front of the mining machine's boom and is ducted to a scrubbing unit located on the machine's main frame. The clean air from the scrubber is discharged as a high velocity jet toward the return, generally from the left fender of the mining machine. When taking cuts deeper than 20 to 25 ft with a scrubber-equipped machine, the machine's discharge is in by the mouth of the blowing curtain, creating a concern by mine workers that a loss of air to the face could result. However, Bureau of Mines research found that the push or throw of air toward the return by the scrubber discharge jet allows good face ventilation to be maintained with extended curtain setbacks.

Jan 1, 1984

By Suzann C. Ambrosio

The mineral industry in Burundi continued to be a minor contributor to the 1980 gross domestic product (GDP) estimated at $293 million in constant 1970 prices.2 Mineral export revenues, primarily from cassiterite, increased by a factor of 15 between 1979-80, reaching approximately $434,000 by yearend 1980. Gold, bastnasite, colombite-tantalite, and wolfremite continued to be exploited on a small scale, using manual and semimechanical methods. Despite a sharp decline in mining activities during 1979, attributed to a lack o? profitability and shortage of construction materials, the mining sector exhibited signs of recovery during 1980. The mineral exploration budget grew 32% over 1979 levels and was equivalent to approximately $42,000 in 1980. In addition, the Burundi Geographical Institute (IGE BU) was created in September 1980 and given responsibilities to collect cartographic, topographic, hydrogeologic, and other geomorphological data., SONIBUROM, the Burundian and Romanian Government joint mineral corporation, conducted mineral deposit inventories during 1979-80 and has been charged with exploiting some of these as yet unspecified resource areas. Another Burundian-Romanian effort, called Mabaya-Butahana, was initiated to search for gold deposits. Meanwhile on the Ruzizi plain, alluvial gold prospecting, with an estimated grade between 0.2 to 1.0 gram per ton, was carried out on a small scale.

Jan 1, 1982

By E. A. Johnson

As part of its effort to reduce the environmental impact associated with mining and metallurgical operations, the Bureau of Mines used a modified form of the Environmental Protection Agency's Extraction Procedure toxicity test on copper reverberatory slags that contained low, medium, and high levels of the impurity elements As, Pb, Sb, Bi, and Zn. All tests resulted in extracts that did not exceed those limits published in the May 19, 1980, Federal Register; there-fore, these solid wastes were designated as nonhazardous for most landfill disposal situations. However, arsenic and lead levels disturbingly close to the allowable limits--and even higher levels of copper and zinc, for which there are no established limits--leached from the high-impurity-element granulated slags. These slags should be handled in such a way so as to minimize the possibility of water contamination. One baghouse dust was tested according to the EPA procedure and found to exceed the extract limits by a factor of 10. This solid waste may be considered hazardous.

Jan 1, 1982

By Steven J. Page, William A. Heitbrink, Andrew B. Cecala, Edward D. Thimons, John A. Organiscak

Miners at noncoal surface mining operations are often exposed to high levels of respirable dust. In an effort to lower the respirable dust exposure of these surface miners, the National Institute for Occupational Safety and Health (NIOSH) has been conducting research to address this problem in a practical and economically viable manner. One successful effort deals with lowering the dust exposure of equipment operators in enclosed cabs. Many types of surface mining equipment utilize enclosed cabs to protect equipment operators from dust exposure. Normally when the equipment is new, the cabs are fairly airtight. These tightly sealed cabs, combined with good filtration systems, generally provide the operator with good dust protection. However, most mining equipment is older, and as aging occurs, many components of the enclosure deteriorate. The structural integrity of the cab diminishes and the effectiveness of the air filtration system fails. NIOSH has been successfully researching costs-effective methods to improve both filtration effectiveness and cab integrity of these older cabs in order to provide a healthier work environment for equipment operators. Dust sampling records indicate that drill operators and helpers have the highest dust exposure of all workers at surface mining operations. Since much of the overburden contains a high percentage of silica, the health hazard associated with this dust can be even more serious. NIOSH research is addressing techniques to lower respirable dust levels at surface drilling operations. INTRODUCTION NIOSH's mission is to assure a safe and healthy work environment for the working men and women of this nation. The primary emphasis of NIOSH's Pittsburgh Research Laboratory (PRL) is mining health and safety research. This report focuses on two areas of research

By Charles C. Boley

The Bureau of Mines dried and carbonized two wood wastes, one softwood (redwood) and one hardwood (oak), using continuous, vertical entrainment techniques previously developed for use with coal. It was demonstrated that these techniques are readily applicable to wood waste and that appreciable changes in the yields of carbonization products can be obtained by varying operating conditions. A limited amount of experimental work was done on briquetting the char-coals. Firm briquets were formed with oak charcoal, although greater quantities of starch binder than used commercially for kiln-produced charcoal were required. Redwood charcoal did not briquet successfully under the test conditions employed.

Jan 1, 1969

By F. N. Kissell, R. J. Bielicki

The Bureau of Mines found sulfur hexafluoride (SF6), released from a lecture bottle, to be an ideal gaseous tracer for studying mine ventilation systems. Air samples were collected in glass syringes and analyzed by electron-capture gas chromatography. In these studies, the lower limit of detection was about 1 part per billion by volume (ppb) of SF6 per part of air. Experiments conducted in a Pennsylvania limestone mine showed this technique useful in evaluating the effectiveness of auxiliary fans, measuring low flow velocities, probing the air circulating near a working face region where ventilation appeared to be poor, and estimating volumetric flow rates in airways of large cross-sectional area and having low flow velocities. This technique was also used in a western vein-type metal mine to measure the amount of return air being recirculated into the intake air due to leakage through old stoped areas.

Jan 1, 1974

To develop a system which will effectively detect and extinguish fires in underground fueling areas while also providing a warning for nearby miners. Approach A system involving optical fire sensors. automatically-released dry chemical and aqueous film-forming fluid (AFFF) fire suppressants, and automatic alarms was designed from off-the-shelf, state-of-the-art components, and was in-mine tested at two mines in the two typical underground fueling area situations: fuel transfer areas and fuel storage areas. How It Works As mines become more mechanized, the number of fire hazards increases since fueling areas are more abundant. Fire hazards are especially serious in deep mines, since escape time is longer. To help solve this growing problem, the Bureau of Mines, in cooperation with the Mine Safety and Health Administration (MSHA) and the National Fire Protection Association (NFPA), has developed and in-mine tested a cost-effective fueling area fire protection system. The system was designed to be rugged enough for reliable, long-term use, yet to utilize state-of-the-art, off-the-shelf components to maintain cost-effectiveness. The system consists of cross-zoned, ultraviolet flame sensors used for quick response to fire, and a dual-agent fire suppression subsystem. A dry chemical is used for fast fire -knockdown," and AFFF (or "light water") is used for long-term, fire-securing capability. The basic components of the system are shown in the schematic illustration.

Jan 1, 1982

By E. D. Regad, W. E. Wallace, V. Vallythan, V. Castranova, P. Hathaway, F. H. Y. Green, M. J. Keane

"Abstract—Inhaled particle contact with pulmonary surfactant in the hypophase lining pulmonary alveoli was modelled in vitro by exposing two respirable sized dusts, kaolin and silica quartz, to lecithin, a major component of pulmonary surfactant, emulsified in physiological saline. Lecithin adsorbs to the dusts upon incubation at 3TC and suppresses their cytotoxicity as measured by pulmonary macrophage and erythrocyte assays, suggesting that pulmonary surfactant provides a defence system against prompt cell membrane lysis by inhaled dusts. Subsequent pulmonary macrophage phagocytosis and lysosomal enzyme digestion of the coated dusts was modelled in vitro by incubation with phospholipase A2 for one hour. With increasing lipase activity, silica haemolytic potential was restored to native silica levels. Kaolin was retoxified to levels far in excess of native kaolin haemolytic potential. Elution, thin layer chromatography and phosphate assay of treated dusts indicate that most lecithin on silica is digested to lysolecithin and desorbed, silica retoxification being due to surface and adherent lysolecithin effects. Most lecithin on kaolin is not digested in the same time; that which is. results in adherent lysolecithin which is responsible for the kaolin retoxification. Digestion with phospholipases A2 and C together produces only weakly retoxified kaolin. Results suggest that surface adsorption properties which control the adherence of prophylactic surfactant distinguish the pathogenic potentials of quartz, kaolin and mixed dust.INTRODUCTIONERYTHROCYTE HAEMOLYSIS and pulmonary macrophage enzyme release assays show quantitatively comparable high cytotoxicities for both silica quartz and kaolin respirable sized dusts (BROWN, et al., 1980; DANIEL and LE BOUFFANT, 1980.) This contrasts with the strong potential for respirable quartz dust to induce pulmonary fibrosis and the much more limited potential of kaolin dust to do the same (MORGAN and SEATON, 1975).In an attempt to understand this anomalous situation, assays were performed on quartz and kaolin dusts incubated with dipalmitoyl lecithin emulsified in physiological saline, to simulate the initial contact of a respired dust with the pulmonary alveolar hypophase. The ability of kaolin dust to adsorb dipalmitoyl lecithin from physiological saline has been quantified (WALLACE, et al., 1975). Such lecithin treatment suppresses the cytotoxicity of both silica and kaolin to background levels (WALLACE, et a1.,1984).Surfactant coated detoxified dusts should then be phagocytised by pulmonary macrophages, incorporated into a macrophage secondary lysosome and exposed to hydrolytic lysosomal enzymes. Among these is phospholipase A2, which hydrolyses diacyl lecithin to lysolecithin. This was modelled by incubating lecithin treated dusts with phospholipase A2 in vitro to determine if the enzyme can digest the dust-adsorbed lecithin, and if the retoxification differs between the two dusts in a manner which might distinguish their pathogenicity."

Jan 1, 1988

By Donald N. H. Chi

This Bureau of Mines report is concerned with a theoretical study of the aerodynamic response of a single mine entry to flame-induced disturbance. The unsteady, one/dimensional, compressible flow equations were solved using the method of characteristics. This study was primarily undertaken to determine the feasibility of extending the method of characteristics to study the aero-dynamic response of complex mine networks. It was demonstrated that although the technique has merit in studying the complex wave interaction in single entries, it appears to be too unwieldly and too expensive for network analysis. Effort was also directed at a further study of the dispersion and filtering characteristic of aerodynamic disturbances in mine passageways.

Jan 1, 1975

A construction material based on plasticized sulfur and mineral aggregate, that is superior in corrosion resistance and strength to portland cement concrete. The material can be used in the chemical, metallurgical, and fertilizer industries, and will also provide an attractive market for by-product sulfur resulting from compliance with pollution regulations. How It Is Made Sulfur concrete is thermoplastic material. Plasticized sulfur is mixed with sand and gravel aggregate heated to 375-400° F. The sulfur melts and acts as the binder or cement. The sulfur concrete is poured hot and sets at a temperature of 200° F. Full strength is attained in a few hours, compared to several days for portland cement concretes. Sulfur concrete even pours and sets in freezing weather. Although unmodified sulfur with aggregate will produce a sulfur concrete with good initial properties, it undergoes crystallographic modifications, and deteriorates with time, particularly when exposed to moisture or freeze-thaw conditions. The Bureau of Mines has developed plasticizers which, when reacted with the sulfur, give sulfur concretes with excellent moisture and freeze-thaw resistance. The plasticizers are based on mixtures of dicyclopentadlene (DCPD) and ollgomers of cyclopentadiene. About 5 percent by weight of the plasticizers is reacted with molten sui fur for several hours. The sulfur cement can be used directly or allowed to solidify for easier handling and storage.

Jan 1, 1981

To perform comprehensive economic evaluations on both existing and proposed mineral operations. Approach A comprehensive computer model was developed which is capable of evaluating the economics of an entire mineral recovery operation, including exploration, acquisition, infrastructure, mining, milling, smelting, refining, transportation, taxation, and return of and on capital. How it Works The MINSIM (MINe SIMulator) economic evaluation concept was developed by the Bureau of Mines in 1967. The initial versions used a continuous discounted cash flow rate-of-return (DCFROR) to measure the effect of changes in expected revenues and costs. Subsequent enhancements to the program have expanded and strengthened MINSIM, especially the addition of an option which determines total production cost (i.e., the commodity selling price that a mineral recovery operation would require in order to obtain a target rate of return), an expanded capacity for evaluating by-products from a mineral property, and significantly broadened taxation determining capabilities. The MINSIM computer program uses essentially the same procedures and calculations that are performed in a manual economic evaluation, although the program accomplishes its tasks much more rapidly and accurately, An experienced mineral economist may require a week to evaluate a single mining operation with the same detail and consistency provided by MINSIM in a matter of seconds of computer time.

Jan 1, 1983

By R. P. Vinson, Abdurrahman Cetinbas, Joseph Cervik, M. G. Zabetakis

The periphery of longwall panels in the Pocahontas No. 3 coalbed is characterized by a zone of reduced permeability that inhibits the natural drainage of methane. A residual gas pressure of 105 psig was measured after 1 year in an isolated block of coal measuring 340 by 1,100 feet. The buildup of gas pressure within such large blocks causes methane problems during plowing operations. However, natural drainage holes drilled during development have been found to reduce the gas content of the coal in this coalbed by over 90 percent. The effect of water infusion on dust during plowing operations was investigated using existing methane drainage holes. These holes were cleaned of debris and a pipe was grouted into the hole for water infusion of the panel. Both total and respirable dust levels were reduced by 40 to 79 percent. Water infusion of the panel proved more effective than did the use of a plow-mounted spray sys tem.

Jan 1, 1974

The object of this program was to extend the capabilities of visual paging systems both in size and function. The system developed uses the mine pager phone line for communication, monitoring, and remote control. A central station, using a mini-computer, transmits signals by phase inversion modulation of a 16,384 Hz carrier to as many as 999 remote units. The remote unit addressed returns an echo to indicate that it is functioning and, in the case of monitor units, to convey the monitor data. Magnetically latched display discs, which can be seen from both sides when posted, are used for visual paging. Lists of the addresses of posted pages, unanswered pages, and non-echoing units are prepared by the central station computer. The system was designed to be intrinsically safe and should operate for three months on a 12-volt lantern battery.

Jan 10, 1980

Objective Develop field measurement and computer modeling methods to predict the potential for hang-ups and structural failures in underground mine ore paws. Background Analysis of Mine Safety and Health Administration (MSHA) accident statistics has identified ore pass hazards as a significant safety problem in underground metal mines in the United Stales. Recent ore pass failures have underlined the lack or ore pass design methods ant1 standards available to both MSHA and mine engineers. Injury and fatality data for the 20-ycar period between 1975 and 1095 show that nearly 75% of the injuries were directly or indirectly related to pulling or freeing ore pass chutes, the use of hand tools, falls or broken rock, and structural failures or chutes or gates and ore pass walls.

Feb 1, 1998

Investigate the use and placement of lightweight concrete to improve ground control technology in deep mines where deformation occurs under heavy ground conditions and where there is danger of rock bursts. Approach Investigations of lightweight concrete properties and placement methods were conducted in the laboratory and in the field. Three test sections were completed: a monolithic, portal-type structure with integral walls and arch constructed aboveground; an underground test section constructed in a mine drift using plywood forms; and a test section constructed in a mine drift using an air-supported formwork. In the two underground test sections, the light-weight concrete was placed using a piston pump with concrete discharge line. A cooperating mine also used lightweight concrete, in the density range of 25 lb/ft3, to replace timber blocking in a raise preparation structure (the enlarged area across a vein where chutes and manway access arc placed). Other experiments included the use of precast lightweight concrete blocks in situations where ground support was needed, such as fur mine, ventilation doors, stoppings, and barricades.

Jan 1, 1990

By Joseph E. Matta

The Bureau of Mines conducted tests using a tracer-gas technique to measure the effectiveness of the jet fan, which is often employed in mines to ventilate dead headings. Results of these tests show that jet fans can (1) ventilate dead headings beyond the maximum penetration distance indicated by smoke-tube detection of air movement, and (2) redistribute available fresh air through larger working areas. However, if the fresh air base is insufficient, the fan will merely recirculate the contaminated air and disperse it over a larger volume.

Jan 1, 1978

Provide a method of detecting and locating miners trapped underground following a mine disaster. Approach Develop a surface deployed system which senses the vibrations caused by a trapped miner pounding on the roof of the mine and effectively determines the miner's location. How It Works If trapped underground, a miner would strike the roof of the mine with any implement at his disposal. This pounding causes vibrations in the ground which are transmitted to the surface where they are sensed by receiving transducers called geophones. Multiple geophones are positioned together for noise cancellation purposes in a form called a subarray. Seven

Jan 1, 1981