Search Documents

By T. A. Klinefelter

"INTRODUCTION During the development work on sponge iron by the Bureau of lines it was desired to produce a product of maximum density for the furnace. One means of doing this would be to make a plastic mixture of the ground ore and extrude as pellets or large slugs or brick shapes.If a pelletizing Process is employed, the pellets must be strong enough to resist breaking when rolled and tumbled in going through the rotary kiln. If a brick-making process is employed, the brick must be strong enough to withstand handling and considerable pressure when stacked in the kilns.The study had two objectives: first, to find a binder of sufficient strength throughout the early stages of curing and heat treating and, second, to determine the degree of curing and heat treatment necessary to prevent disintegration under normal working conditions.Although the investigation had as its primary objective the processing of sponge iron, the data should interest other industries in which non plastic or poor-bonding slimes are a problem."

Jan 1, 1946

By R. E. Lindstrom

Effective separation of rare-earth mixtures is obtained using hydrogen as a retaining ion at 200° F with ethylenediaminetetraacetic acid (EDTA) eluant. Results obtained in Bureau of Mines bench-scale apparatus and large columns with hydrogen as a retaining ion closely parallel those obtained with copper as a retaining ion. The use of hydrogen as a retaining ion permits EDTA and water, collected before rare-earth breakthrough, to be recovered in a form that allows the material to be recycled without extensive processing. With the exception of yttrium and dysprosium, separation of rare-earth mixtures is improved and throughput is increased by elevated temperatures. Separation with 1,2-diaminocyclohexanetetraacetic acid (DCTA) eluant increases markedly on increasing temperature from ambient to 250° F; however, on the basis of separation efficiency, DCTA does not compare favorably with EDTA.

Jan 1, 1962

By F. A. Rutledge

The Rainy Creek deposits lie at the western base of the Kilbuck Mountains, about So miles southeast of Bethel, in southwestern Alaska. The deposits were brought to the attention of the Bureau of Mines by placer miners on Rainy Creek after cinnabar concentrates were recovered by their gold-mining operations. In August 1947 the Bureau excavated 1,500 feet of dozer trenches totaling 2,547 cubic yards. Further hand trenching in the bottoms of the dozer trenches on the surface totaled 1,440 linear feet, or 40 cubic yards. Nineteen samples were taken for analyses.

Jan 1, 1948

By John J. McClelland

The Bureau of Mines conducted a study of longwall plow operations to identify dust sources and existing control technology. Three longwalls employing either the high-speed overtaking or conventional method of mining were surveyed. Principal operating parameters and on-site dust control technology at the time of each survey are described. Short-term gravimetric and instantaneous sampling results are discussed in detail. The relationship between longwall dust levels and dust control technology was examined.

Jan 1, 1988

This report summarizes the results of several field tests conducted by Collins for the Bureau of Mines under contract SO122076 and contract H0232056. The field projects represent a part of Collins continuing effort on a broad study of coal mine communications. These experiments analyze the propagation characteristics of radio signals in a working coal mine environment. The intent of the program is to provide basic propagation loss characteristics by which we may evaluate various approaches to an integrated mine communications system. The goal of such a system is to satisfy both operational and emergency communications needs in the mine. Field testing was conducted during the last week of November 1972, at a coal mine operated by Inland Steel Company, near Sesser, Ill, and in the Robena No. 1 Mine, Waynesburg, Pa, on 12 March 1974. The tests included uhf propagation losses and noise (200 MHz to 1 GHz) in the Sesser, I11 mine location and vlf propagation loss and noise (1 to 200 kHz) in both of the above locations. The basic experimental parameters were frequency, polarization, antenna type/orientation, and distance. The following reports treat the various aspects of the test programs in detail. Since different antenna configurations were used in the two mines, each report contains its own experimental predictions drawn from its corresponding test activities. A test equipment list and block diagrams of typical experimental setups for the tests of section 2 are contained in appendix A.

Jan 1, 1974

By C. J. Thompson

In the course of the work currently conducted by the Bureau of Mines in cooperation with the American Petroleum Institute Research Project 48 on identifying sulfur compounds in petroleum, a micromethod was developed (12)5 for catalytically removing the sulfur atom from sulfur compounds. The product is the residual portion of the molecule; the structure otherwise was unaltered except for hydrogenation of any unsaturated bonds that were present in the original compound. Positive identification of sulfur compounds isolated from crude oils is a difficult problem. Direct comparison of properties of the unknown with those of reference compounds is often impossible because of the limited number of reference sulfur compounds available. However, a relatively large number of pure hydrocarbons is available, and the conversion of the sulfur compound to a hydrocarbon enhances the possibility of identification. The technique also can be used to prepare microquantities of scarce hydrocarbons by hydrogenating compounds that are readily available.

Jan 1, 1962

By E. J. Kloos

The Bureau of Mines developed a test for evaluating gas masks designed to protect against phosphine gas; phosphonium iodide is used as a source of phosphine. Gas masks approved by the Bureau for respiratory protection against phosphine include the GMC-SS-1, Mine Safety Appliances Co.; the LG-10 and LG-10G, Willson Products Division, The Electric Storage Battery Co.; and the 084-PHOV-R, Acme Protection Equipment Co.

Jan 1, 1966

By Victor Himel

This report documents a systematic approach towards implementing an improved ensemble for the mine rescue team system that will protect against the hazards of mine rescue and recovery and will also afford improved performance through increased comfort and maneuverability, lighter burdens, and improved human engineering designs. In the first part (Task 1) the mine rescue team's protective needs were defined along with the test methods required to evaluate whether a particular piece of gear met these needs. Task 2 assessed existing gear against performance criteria and standards developed in Task 1. Task 3 consisted of the conceptual design and construction phases of the MRPE program. Special consideration was given to advanced concepts, materials, and equipment.

Jan 1, 1982

By T. A. Johnson

Recovering from low demand in 1975, raw mineral production in the United States maintained a steady climb in value and quantity throughout 1976, keeping pace with the gross national product (GNP), which increased 11.5% compared with that of 1975. The minerals industry, in the past, has met ever-increasing demand while keeping production costs to a minimum. To maintain this capability, technological research and development of more efficient processing methods must continue. The role of Government and its increasing involvement in minerals industry actions received unfavorable comment from various segments of the industry in 1976. Government pricing controls were of concern to most industrial firms marketing like products. Public land withdrawals in large blocks were of concern to the mineral industry.

Jan 1, 1978

By Robert P. Vinson

This report describes three coal mine ventilation studies by the Bureau of Mines in which sulfur hexafluoride (SF6) was used as a tracer gas. One of these studies was conducted to determine air movement and leakage in a sealed area. Another was run to determine the ventilation efficiency of a bleeder system. Finally, a study was made of air leakage across permanent stoppings of parallel intake airways. These studies proved sulfur hexafluoride to be a useful addition to the equipment commonly used in coal mine ventilation analysis.

Jan 1, 1976

By D. E. Wolfson

Destructive distillation (carbonization) was shown to be a feasible method of disposing of scrap tires. The Bureau of Mines conducted tests under a variety of conditions. Solid, liquid, and gaseous products were produced, recovered, and analyzed. The quantities of the various products were shown to be quite dependent on the test temperature. Variability in composition of the liquid and gaseous products with changes in test temperature was also significant.

Jan 1, 1969

By Paul Hopkins

The following methods have been selected from a large number tried while assaying several hundred samples of placer concentrates. It is thought that some of these methods may be useful to those who are required to assay similar products containing large quantities of metallic articles, such as jeweler's sweepings. No great difficulties will be encountered in assaying black sand from beaches or river bars. Such samples require care in grinding and sifting so that no oversize particles of gold or platinum are lost. It is also necessary to have sufficient silica in the flux to form a fluid slag with the excess of iron, magnesium, or chromium which such samples contain. It is much more difficult to assay black sands, or concentrates, produced in large-scale placer-mining operations. These products are usually much harder and more abrasive than the beach black sands. They also contain numerous metallic particles resulting mainly from wear on the mining machinery. These particles consist chiefly of iron or steel but also contain lead, copper, and alloys such as babbitt, solder, brass, ferrosilicon, etc. Fairly large particles of gold are often found. Some samples will contain as much as 10 percent of such metallic particles. It is not feasible to remove the particles of iron with a magnet and discard them, as they invariably contain gold, sometimes a considerable amount. This gold is attached to the iron particles by rust or wedged into cavities. Scraps of sheet iron are often found which have become tightly folded or rolled and contain gold or amalgam within the folds.

Jan 1, 1934

By Noel N. Moebs

Coal mine roof failure is categorized according to character, trend, or pattern of occurrence. Two principal categories of failure are proposed--geology related and stress related. Geology-related failure includes both lithology and structure. Each of several subcategories reflects the probable cause of failure and thereby provides a basis for the selection of appropriate techniques for reducing the incidence of failure. These control techniques, depending on local conditions, may include supplementary support, destressing, reduction of mine air humidity, or a change in the customary support methods.

Jan 1, 1986

By Norwood B. Melcher

This report describes preliminary experiments by the Federal Bureau of Mines on the practicability of adding raw pellets of taconite concentrate to blast furnace feeds. The usual industrial practice is to harden the pellets by heating before they are charged to the furnace. The Bureau research demonstrated that raw pellets could be successfully smelted in an experimental furnace with no significant change in coke consumption and only a moderate increase in dust losses. The dust loss was 43 pounds per ton of metal for an all-pellet charge, compared with 7 pounds per ton for an all-sinter charge. Raw taconite pellets undergo only slight degradation during charging to the furnace if 1 percent bentonite is used as a binder. INTRODUCTION Fines and concentrates must be consolidated or agglomerated into larger masses before they can be smelted in a commercial blast furnace. Such agglomeration is usually done by sintering, pelletizing, nodulizing, or briquetting. Sintering has been the more common practice, but with the advent of taconite concentrates pelletizing is increasing in importance.

Jan 1, 1960

By D. S. Kingery

The practice of using doors to control main ventilating currents in bituminous-coal mines is common throughout the industry. When doors are erected in pairs to form air locks, they are usually accepted as satisfactory by both State and Federal coal-mine-inspection agencies. A review of the contributing factors in recent methane ignitions showed that interrupted ventilation (often caused by doors latched open, destroyed, or damaged) was the principal cause of methane accumulations that subsequently were ignited.

Jan 1, 1958

By D. S. Kingery

The data obtained from this study cover test areas that are gassy to ultragassy and pillared areas of different sizes and degrees of tightness. The methods of controlling ventilation, applying bleeders, and supporting bleeder entries varied in the different test areas. It was not possible to study all conditions likely to be encountered in coal mines. Undoubtedly, there are areas where bleeder entries, even though properly planned and maintained, might prove unsatisfactory. However, on the basis of this study, the following observations were made: 1. Tests showed that each bleeder system studied provided some movement of air through the pillared area; the quantities of air delivered to the pillar line, ranged from 23 to 82 percent, depending mainly on the extent to which bleeder re-turns were used as main returns from the section. 2. Pressure measurements taken across pillared areas showed maximum pressure drops ranging from 0.05 inch of water for a shallow gob to 2.69 inches for a very deep gob. The pressure differentials varied with the size and tightness of the gob but proved adequate to induce airflow across worked-out areas or through fringes of the gob to the bleeder return system.

Jan 1, 1957

By G. W. Murrie, W. P. Diamond, S. W. Lambert

A geologic study of the Mary Lee Group of coalbeds in the Black Warrior coal basin was undertaken to examine coal stratigraphy and determine regional trends and extent of the coalbeds. The area investigated encompasses 835 square miles in Jefferson, Walker, and Tuscaloosa Counties, Ala. More than 700 core logs were used to construct a structure map, coal, interval, and overburden isopachs, and cross sections. There is evidence that structure affected sedimentation. Coalbed isopachs indicate the Mary Lee Group was deposited in fluvial-deltaic and low-lying coastal plain environments. The Mary Lee coalbed is the only coalbed which is continuous throughout the area, commonly with two benches which have a combined thickness of 2 to 12 feet. The Mary Lee coalbed changes rank in the basin from high- through medium- to low-volatile coal. The methane gas potential of the Mary Lee Group coals is estimated to be greater than 1 trillion cubic feet. There is an excellent correlation between the orientation of surface cleats with those measured underground in the Mary Lee coalbed. The face cleats roughly parallel the axes of the area's folds and trend northeast-southwest.

Jan 1, 1976

By Iam Pou Ng

Combustion aerosols consist mainly of elemental and organic carbon (EC and OC). Since EC strongly absorbs light and thus affects atmospheric visibility and radiation balance, there is great interest in its measurement. To this end, the National Institute for Occupational Safety and Health (NIOSH) published a standard method to determine the mass of EC and OC on filter samples. Another common method of measuring carbon in aerosols is the aethalometer, which uses light extinction to measure "black carbon" or BC, which is considered to approximate EC. A third method sometimes used for estimating carbon in submicron combustion aerosols, is to measure particle size distributions using a scanning mobility particle sizer (SMPS) and calculate mass using the assumptions that the particles are spherical, carbonaceous and of known density. With an eye toward evaluating the use of these methods for measuring carbon in freshly emitted diesel aerosols, the objective of this paper is to compare the results among these methods and to investigate the role of OC when measuring the mass concentration of elemental carbon (or black carbon) in aerosols emitted by a medium-duty Diesel engine. Results indicate that the aethalometer response correlates well with the data from filter samples (R2 = 0.99), with a very slight positive interference at high levels of OC.

Jan 1, 2008

By E. J. Kloos

The Bureau of Mines developed a test for evaluating gas masks designed to protect against phosphine gas; phosphonium iodide is used as a source of phosphine. Gas masks approved by the Bureau for respiratory protection against phosphine include the GMC-SS-1, Mine Safety Appliances Co.; the LG-10 and LG-10G, Willson Products Division, The Electric Storage Battery Co.; and the 084-PHOV-R, Acme Protection Equipment Co.

Jan 1, 1966

By Paul Hopkins

The following methods have been selected from a large number tried while assaying several hundred samples of placer concentrates. It is thought that some of these methods may be useful to those who are required to assay similar products containing large quantities of metallic articles, such as jeweler's sweepings. No great difficulties will be encountered in assaying black sand from beaches or river bars. Such samples require care in grinding and sifting so that no oversize particles of sold or platinum are lost. It is also necessary to have sufficient silica in the flux to form a fluid slag with the excess of iron, magnesium, or chromium Which such samples contain.

Jan 1, 1934