Search Documents

By M. L. Odenbaugh

The viscosity reduction effect of varied concentrations of leonardite (a naturally oxidized form of lignite) and leonardite-caustic on the rheological properties of a standard bentonite drilling fluid was studied and evaluated. The minimum plastic viscosity was found to occur at application rates of 4 lb of leonardite and 1.33 lb of caustic per barrel of drilling fluid. Leonardite-caustic treatment was not beneficial in treatment of salt-contaminated drilling fluids. Although filter loss rate was reduced; both yield values and gel strength were increased. Compared with other viscosity control agents) including quebracho) ligno-sulfonate) humic acids extracted from leonardite) as well as other reaction products of lignite) leonardite is less effective at low application rates but is an effective treating agent at rates of 2 Ib/bbl or more. Considering the comparable merits of the substance tested) the major factor in determining which agent to use should be based on cost consideration.

Jan 1, 1967

By F. S. Crawford

Untreated timber in a mine or elsewhere may fail prematurely because it may "rot out before it wears out." If such timber is treated with a satisfactory preservative, decay will be retarded for many years, and it's serviceable life will beg prolonged to several times that usually obtained from untreated timber.4/ Treated timber has many advantages, and although it has been used extensively by railroads and other large consumers of structural timber, the relatively small use in mines seems strange indeed. Timber does not decay if it is kept dry, cool, and well-ventilated or if it is kept constantly wet or sumberged in water. At a mine in Canada the temperature in the upper levels was only 44° F., and the timber did not decay. As operations deepened, however, warmer ground was opened, and, with high humidity, conditions favored timber decay. The life of untreated timber may be only 2 to 3 years under such conditions.

Jan 1, 1951

By Donald P. Blasko

The Bureau of Mines investigated two areas of the Alaska Peninsula (Iniskin Peninsula and Becharof Lake) where oil and gas seeps were known to occur in an attempt to determine (1) whether the seeps are still active and (2) the amount of bitumen contained in the drainage leaving the seeps. The oil, water, oil-water, and gas were sampled and analyzed. Five oil samples were taken at four separate oil seeps. The API gravity of the oil ranged from 8.90 to 21.4° and the sulfur content was from 0.12 percent to 0.59 percent. Four of the seven gas samples obtained revealed fair high caloric values, ranging from 746 to 924 Btu/cu ft, and averaging 844 Btu/cu ft. A total of 44 water samples were obtained. Bitumen content of the water was as high as 9,773 mg/l at one seep, but averaged less than I mg/l where the seep-drainage water entered the Gulf of Alaska.

Jan 1, 1976

By H. B. Salisbury

The Bureau of Mines conducted research to determine if low-grade California chromite ores could be beneficiated to produce products suitable for commercial use. This research is part of a Bureau goal to provide technology capable of using low-grade domestic ores to meet emergency demands of the Nation for metals and minerals and in particular those minerals, such as chromite, which are considered critical. Two ores from California were ground and treated using gravity concentration and magnetic separation techniques. An are from Auburn in central California, assaying 2.5 pct Cr203, was treated by tabling and magnetic separation to yield a nonmagnetic product containing 44.7 pct Cr203 at a recovery of 36.4 pct. Core drilling samples from the Seiad Creek area of northern California, assaying about 6 pct Cr203, were upgraded by tabling to yield a concentrate containing nearly 50 pct Cr203 with a recovery of 50 pct. Both products are suitable for metallurgical and/or chemical use.

Jan 1, 1981

By H. E. Powell

The mineral dressing research here reported is part of a continuing program by the Bureau of Mines to develop new or improved concentration processes for oxidized or partly oxidized lead and zinc ores. A sample of low-grade sulfide-oxide, lead-zinc ore from Jasper County, Mo., containing galena, cerussite, pyromorphite, hemimorphite, smithsonite, and sphalerite was concentrated by froth flotation and tabling to a grade of 66 percent lead. Because of the presence of a high content of slime-size values, the overall recovery of lead was limited to 64 percent at this grade. Tests to recover the zinc by froth flotation and by gravity concentration did not give satisfactory results. INTRODUCTION Since its establishment, the Rolla Metallurgy Research Center has con-ducted studies of base metals as a part of its overall program (1, 2, 3, 4, 5,6,7).3/ This research has been, and is, directed to beneficiating complex and submarginal ores, to retreating rejects from commercial installations, and to developing fundamental data.

Jan 1, 1960

Develop a training program to help mine workers effectively fight small fires in underground Goal mines. Training would enable miners to make rapid judgments on whether to attempt extinguishment, and how best to use the firefighting equipment on hand. Approach Fire reports were analyzed to define and delineate physical and behavioral variables which affect firefighting activities, and to determine effective procedures for extinguishing small fires. A course was then designed to train miners in such procedures. Finally, the course was reviewed by industry experts and administered to a group of miners to determine needed revisions and to validate the course. How It Works Analysis of fire data showed that six items should be emphasized in teaching proper fire response: 1. Alertness to fire potential. 2. Immediate power cutoff. 3. Internal, external communication. 4. Teamwork in fighting fires. 5. Role of ventilation and position of men inby the fresh air side. 6. Effective use of fire suppressant materials.

Jan 1, 1983

By Ann G. Kim

Hydrocarbon gases, primarily methane but also the Ca through Cs paraffins, the Ca and C3 olefins and possibly the C4 and Cs olefins, are byproducts of coal formation. Although it is generally believed that coal formation occurred at temperatures below 200° C, most experimental work on gas formation from coal has been performed at temperatures between 200° and 1,000°C. The objective of this Bureau of Mines experiment was to determine if observable changes in the gases from coal could be produced at temperatures below 200° C in relatively short periods of time. The experiment involved heating coal samples from six coalbeds at constant temperatures and analyzing evolved gases. The composition of the gases at three temperatures was compared. At 35° C, over 99 pet of the gas is methane; at 125° and 150°, methane constitutes approximately half of the hydrocarbon gas. Isobutane and pentane are the predominant higher hydrocarbons at temperatures between 100° and 150° C.

Jan 1, 1974

Improve the effectiveness of face ventilation systems in coal mines by minimizing leakage around line and check curtains. Approach In-mine surveys were conducted to determine current curtain construction techniques, their effectiveness and associated costs. In addition, performance characteristics of extensible curtains were evaluated. A total of 77 conventional curtains in 10 mines was examined for 12 important characteristics. Extensible curtains were erected in a full-scale model and examined for operational difficulties, effects of leakage, and air pressure. Survey Results The underground mine study identified four categories of face brattice construction ranging from simple to complex: 1. Simple suspension of the curtain from roof bolts with the bottom edge lying on floor. 2. Spadding of the curtain to the roof on about 12-inch centers and stabilization of the bottom edge with wood or rock. 3. Use of vertical props and spads with a base board for support on the bottom. 4. Use of vertical props with caps and bottom boards plus horizontal brattice support boards.

Jan 1, 1984

By R. A. Friedel

Data on compositions of natural substances are important in the study of possible interrelationships. The similarity of the low molecular weight alkane isomers from crude oil and Fischer-Tropsch catalytic synthesis product has been reported (8).3 A similar composition for the alkane isomers from high-temperature coal carbonization has been found. The composition of the C4 to C 7 alkane isomers from these three sources can be calculated quantitatively with the equations previously developed to calculate alkane isomers in Fischer-Tropsch product. An KM sting reversal of the concentrations of the monomethyl isomers from C6(2 Me > 3 Me) to C7 (3 Me > 2 Me) occurs in all three products; fragmentary comparisons at higher carbon numbers indicate some dissimilarities. Naphthene isomers in the C6 to C7 range for crude oil and high-temperature coal carbonization also have similar compositions. Aliphatic hydrocarbons from low-temperature coal carbonization processes are considerably different, consisting mainly of normal alkanes.

Jan 1, 1968

By Oliver C. Ralston

OUTSTANDING TRENDS of the year included the following: 1. Concentration and beneficiation of iron ores to provide improved blast-furnace feed and extend ore reserves. 2. Successful development of pelletizing and sintering procedures for fine iron ores. 3. The realization that cyclone separation could replace existing classifiers in many grinding circuits. 4. The rapidly blossoming metallurgy of ultrapure silicon and improvements in zone melting. 5. The rapid increase in the use of liquid-liquid extraction and ion exchange in hydrometallurgy. 6. The industrial application of vacuum melting on the 100-ton scale. 7. The hope for developing a columbium (noibium) base alloy for high-temperature use. The technologic advancement in metallurgy that had the greatest effect on the American economy was the beneficiation of iron ores to give improved feed for blast furnaces and indirectly extend our ore reserves. This was not a sudden development but rather culmination of a decade of intensive effort.

Jan 1, 1958

By Milford L. Skow

Utilization of domestic ores in the winning of metallurgical alumina requires a convenj.ent method of treating siliceous bauxites and other aluminous materials. In the United states there are only small reserves of high-grade bauxite but considerably larger tonnages of low-grade material. In addition, there are large deposits of high-alumina clays. If these high-silica bauxites or high-alumina clays could be beneficiated, either by are dressing or by chemical dissolution to remove a large proportion of the silica, then the potential reserves of aluminum ores would be increased materially. Faced with a similar situation, the German industry, chiefly dependent on high-grade French bauxites prior to World War II, was compelled during the war to Use lower-grade ores. For desilicating the lower-grade bauxites before the Bayer treatment, a method was developed in which the bauxite was calcined and then given a dilute caustic leach preliminary to the pressure digestion. It was planned to regenerate the caustic by treatment of the desilication liquor with lime. As European bauxites are mineralogically different from those found in this country, preliminary work was undertaken to determine whether this process might be applied to domestic materials. The results of this work, along with a review of the German process, are presented in this report.

Jan 1, 1950

Lower costs associated with hands-on training in donning and using a CSE ,self-contained self-rescuer (SCSR). Background In June 1987, the Mine Safety and Heath Administration (MSHA) issued an Emergency Temporary Standard (ETS) requiring that all persons entering underground coal mines must be given bands-on SCSR training. The ETS will shortly be replaced by a new standard requiring this hands-on training. Bureau of Mines research has shown that the most effective means of delivering this training is to have the trainee go through a six-step training procedure while in a kneeling position. Once the miner has looped the neckstrap over his or her head, he or she completes the donning sequence in this order: 1) activate oxygen; 2) insert mouthpiece; 3) put on nose clips; 4) put on goggles; 5) adjust neck and waist straps; and 6) replace miner's cap and prepare to move out. This procedure is repeated until the miner demonstrates that he or she is proficient at the task.

Jan 1, 1988

By C. P. Bowie

During the period of 10 years from January 1, 1908, to January 1, 1918, approximately 12,850,000 barrels of oil and 5,024,506,000 cubic feet of gas were destroyed by fire in the United States, entailing a total estimated property loss of $25,254,200. During this period 503 fires were reported. As is shown in Plates I and II, 310 of these fires were caused by lightning and 193 by all other causes. The losses from the fires caused by lightning were estimated to be $11, 148,000, and from those due to all other causes $14,106,200. Directly and indirectly, the fires resulted in the deaths of nearly 150 persons and were responsible for almost as many more being permanently disabled. For the past three years the Bureau of Mines has been conducting investigations to determine the nature and the specific causes of these fires, with a view to suggesting means whereby they may be suc- cessfully combatted and, in some places, perhaps eliminated entirely. As the subject of oil and gas fires is necessarily broad, no attempt is made in this bulletin to treat it exhaustively; rather the bulletin aims to point out what has been done by operators in the past, and to describe various fire-prevention methods and fire-fighting appa- ratus which are being used or adopted by many of the larger oil companies. These methods and apparatus, it is believed, if uni- versally employed by operators, will largely decrease the present enormous annual losses. In the discussion of oil-well fires, the methods used in extinguishing several of the larger and more perplexing ones are described. As the right procedure for extinguishing any oil-well fire must be de- termined largely by local conditions, it is not probable that all of the methods used at some one fire, as described, will be applicable to a future fire. However, the operator, from these descriptions, may at least gain suggestions that will greatly assist him in fighting similar fires.

Jan 1, 1919

By W. P. Yant

Public interest in atmospheric pollution by automobile exhaust gas and in the ventilation of vehicular tunnels makes it desirable to ascertain whether the use of modern automobile fuels is tending to change the amount and composition of the products of combustion. The Bureau of Mines, in cooperation with the Ethyl Gasoline corporation4, has completed a series of testis to determine whether any significant difference exists in the carbon monoxide content of the exhaust gas produced by an internal-combustion engine when its fuel is changed from straight gasoline to the same gasoline containing Ethyl fluid whose active ingredient is tetraethyl lead. In the tests data was sought relative to the composition and mount of the gas produced by ordinary comparatively low-compression motors as well as by higher-compression motors in which distinct detonation occurred with straight gasoline, but which operated without detonation when using the same gasoline containing tetraethyl lead.

Jan 1, 1929

By Kenneth L. Cashdollar

While underground coal technology has progressed over time, regulations on coal dust have not kept up ? the most recent rules are more than 80 years old. The National Institute for Occupational Safety and Health and the Mine Safety and Health Administration conducted a joint survey recently on coal particle ranges as measured in US coal mine samples. In underground coal mines, dust explosions are prevented by the addition of enough rock dust (usually limestone) to make the total dust mixture inert. The rock dust acts as a heat sink for the dispersed dust mixture by reducing the temperature below the value needed to propagate an explosion. Federal regulations require 65% in combustible content in intake airways and 80% incombustible content in return airways, where the coal dust is assumed to be finer in size. The regulations also require an additional 1% incombustible for each 0.1% methane in the ventilating air in intakes and 0.4% additional incombustible for each 0.1% methane in returns.

Jan 1, 2008

By Anthony Iannacchione

One of the more pressing engineering problems for deep longwall mines in the Southern Appalachian Basin is to design longwall systems that will eliminate catastrophic coal pillar failure from the working environment. The purpose of this study is to quantify the behavior of a particular size abutment pillar prone to burst or bump. Because the 24.4-111 (80-ft) square abutment study pillar is within the pillar size commonly used in this region, understanding the behavior of this pillar should aid in future efforts to design optimum mining strategies. This research has attempted to construct the pillar stress and roof-to-floor convergence profiles in order to evaluate the ultimate strength, deformation modulus, visco-elastic deformation, and violent failure characteristics of the pillar during longwall mining. This information reflects the overriding influence of the local geologic characteristics on bursts, provides the field measurements needed to verify concurrent modeling studies, and suggest some basic mechanisms associated with the coal pillar bursts discussed in this paper.

By Sean Gallagher, Thomas G. Bobick

The Bureau of Mines performed a pilot study examining the effects of posture on back strength and Maximum Acceptable Weight of Lift (MAWL) on six healthy male subjects (M = 32 years + 4 SD). Six hack strength measurements (3 static and 3 dynamic) were made while the subjects were kneeling and standing. In addition, these subjects (who were unaccustomed to lifting in these postures) volunteered to participate in a study of psychophysically determined NAWL in both postures. Results of the back strength tests showed a significantly lower peak torque per body weight output in kneeling versus standing hack strength measurements for five out of six test comparisons (p < .05). Subjective estimates of lifting capacity in the kneeling posture were significantly lower than those for the stooped posture (p < .05). The results of tests of hack strength and lifting capacity in these two postures provide useful information to consider in determining the physiological and psychophysical stresses imposed by these

By J. W. Horne

The quantitative determination of salt in petroleum ins generally divided into two steps - (1) extraction of salt from the oil and (2) accurate measurement of the extracted salt. This paper presents a method used by the Bureau of Mines for quantitatively extracting the water-soluble chloride salts4/ from petroleum and discusses important details attendant on the success of the method. Among these details are homogeneity in the dispersion of salt crystals, emulsified brine and other impurities in the oil sample, complete solution of the salt, and total extraction and titration of all the aqueous phase. Recently, the chlorides of sodium, calcium, and. magnesium produced with and present in various oils have developed growing problems of salt deposition and corrosion in the petroleum industry. Therefore, a technical study of various emulsions and salts that accompany petroleum is being made by the Bureau of Mines in cooperation with the State of Oklahoma. One report (5)5 reviewing the literature pertinent to the study has been published.

Jan 1, 1940

By J. W. Horne

The quantitative determination of salt in petroleum ins generally divided into two steps - (1) extraction of salt from the oil and (2) accurate measurement of the extracted salt. This paper presents a method used by the Bureau of Mines for quantitatively extracting the water-soluble chloride salts4/ from petroleum and discusses important details attendant on the success of the method. Among these details are homogeneity in the dispersion of salt crystals, emulsified brine and other impurities in the oil sample, complete solution of the salt, and total extraction and titration of all the aqueous phase. Recently, the chlorides of sodium, calcium, and. magnesium produced with and present in various oils have developed growing problems of salt deposition and corrosion in the petroleum industry. Therefore, a technical study of various emulsions and salts that accompany petroleum is being made by the Bureau of Mines in cooperation with the State of Oklahoma. One report (5)5 reviewing the literature pertinent to the study has been published.

Jan 1, 1940

By Joseph C. Zelanko, Christopher Mark

During August, two eastern Kentucky coal miners died in a roof fall during retreat mining operations. They had just finished extracting one pillar block and were moving to the next one when the intersection they were standing in collapsed. Regrettably, this was not an isolated incident. Since the end of 2000, there have been 28 ground fall fatalities in U.S. coal mines. Of these, 10 occurred during pillar recovery operations. Although pillar recovery has been associated with about one third of recent ground fall fatalities, it accounts for only about 10% of U.S. underground coal production. Statistically, a coal miner engaged in pillar recovery is several times more likely to be killed in a ground fall than a miner on an advancing section of a longwall. Pillar recovery is dangerous because it creates an inherently unstable situation. Once the pillars are extracted, the roof is expected to cave. Safe pillar recovery does not mean preventing roof collapse, it means ensuring that it only occurs after the miners have completed their work and have left the area. Fortunately, there are a number of proven techniques that can greatty reduce the hazards of pillar recovery. These include better mine planning, improved roof support, and safer work procedures. The goal of this article is to describe the most significant "risk factors" associated with pillar recovery, and prescribe control techniques that, taken together, can reduce the overall risk to miners. The conclusions are based on extensive studies conducted by the National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) that have included detailed analysis of every fatal retreat mining incident since 1992 (25 incidents resulting in 30 fatalities). Risk reduction strategies for pillar recovery can be divided into three main groups: Global Stability: Prevention of section- wide pillar failure; Local Stability: Prevention of roof falls in the working area; and Work procedures and worker location: Minimizing exposure to hazardous areas.