Search Documents

In this Part, we have included copies of the flip charts and overhead projector viewgraphs used in the two briefings we conducted as part of this seismic detection and location task. The first one was an overview and problem definition briefing given to the seismic consultants on September 7, 1972. The second was a formal oral presentation of study results to technical staff members of the Pittsburgh Mining and Safety Research Center on November 21, 1972.

Jan 1, 1974

By B. W. Madsen

A nearly dormant copper sulfide pilot-scale experimental leach containing 8.7 tons of are was injected with oxygen to determine its effect on the copper-leaching rate. Prior treatment of the uncrushed 0.25-percent-copper, mine-run stripping material consisted of 461 days of acid ferric sulfate leaching, which extracted 47 percent of the total copper. The permeability of the bed had decreased, and the percolation rate had decreased from an initial 20 gallons to 0.8 gallon per square foot per day. Copper extraction had nearly stopped. After injecting oxygen into the ore column and leaching for 30 days, the percolation rate was increased to 6 gallons per square foot per day. In an additional 298 days of leaching, an additional 40.7 percent of the copper was extracted. The improved leaching after the use of oxygen is attributed to stimulated bacterial action, better oxidation, and increased permeability.

Jan 1, 1975

By D. R. Dolinar, J. Pablic, D. C. Oyler, T. P. Mucho

At a mine in central PA, high horizontal stresses have caused long running roof falls resulting in hazardous conditions for the miners and the premature abandonment of panels. Because of these conditions, the mine requested assistance of the National Institute for Occupational Safety and Health (NIOSH) in utilizing the 'advance and relieve method to mitigate the affects of horizontal stress on the mine roof. "Advance and relieve" mining involves the removal of a pillar or a portion of a pillar during development, thereby creating a cave along one side of the panel. Following cave development, the horizontal stress is relieved over the workings adjacent to the cave in the active panel. The mine has used this system in three panels with a significant reduction in stress damage and no large roof falls.

By D. E. Hirsch

The Bureau of Mines, as a part of American Petroleum Institute Research Project 60, Characterization of the Heavy Ends of Petroleum, has made extensive use of gel permeation chromatography (GPC). Data developed in this study were used to develop several correlations that greatly expanded the usefulness of GPC and the data have been used as an aid in the interpretation of mass spectra (MS). GPC retention volume data on pure compounds were used with molecular structure to develop correlations that can be used to accurately predict retention volumes, molecular volumes, densities, chain lengths, and ring numbers of many components of petroleum without resorting to further laboratory experimentation. Conversely, the correlation can be used to select or reject some compounds from several possible compounds that are indicated on the basis of MS analysis. The utility of these correlations in compound type characterization is demonstrated by showing their application to 330° to 550° C fractions from a low-sulfur and a high-sulfur crude oil.

Jan 1, 1974

By H. E. Powell

Over 5 million lb of chromium, 1 million lb of nickel, and 90,000 lb of molybdenum are lost annually in the dusts generated in the production of stain-less steel. Additional losses of these metals in the form of mill scale and grinding swarf may be double the dust losses. This Bureau of Mines report describes a process for recovering these and other metals in the form of an alloy steel suitable for recycling. Zinc and lead, when present in the wastes, are recovered as byproducts in the form of oxide fumes. The laboratory-scale process (10-to 25-lb charges) recovers up to 95 pct of the chromium, 100 pct of the nickel, and 100 pct of the iron. The resultant alloy contains from 10 to 20 pct chromium, 6 to 12 pct nickel, and 55 to 65 pct iron, with lesser amounts of molybdenum and manganese. The alloy is essentially free of zinc, lead, and sulfur. The zinc-lead fume obtained from the treatment contains about 40 pct zinc and 20 pct lead and represents essentially complete recovery of these metals.

Jan 1, 1975

By Stuart Lipoff, John E. Trombly, Paul Brien, O&apos

System objectives and design criteria for an in-mine ULF radio paging system are discussed. Coding formats, frequency and bandwidth selection criteria leading to the system design are discussed. The prototype call alert transmitter and pocket page receiver is functionally described. The report includes circuit descriptions, schematics, parts lists, printed circuit fabrication and assembly drawings. The report concludes with an estimate of the manufacturing cost for each assembly.

By Thomas M. Barczak, Christopher Mark

Roof supports can only be understood in conjunction with the rock structure that they support. The strength of the rock depends on geology, and the loads are applied primarily by the in situ and mining-induced stresses. Other factors, such as wider spans and retreat or multiple-seam mining, can also reduce the stability of mine openings. Roof supports are used to help stabilize these openings, but their performance characteristics must be properly matched to the loading environment and ground behavior if they are to succeed. Roof supports include both intrinsic supports, such as roof bolts, and standing supports. The key characteristics of any support include its maximum load-carrying capacity, stiffness, and residual strength. Other important factors are the timing of installation, the stability of the support as it is loaded, and the capability of the support system to provide skin control. This paper explains in practical terms how supports work and the important factors in ensuring that a good support design and application strategy are developed.

Jan 10, 2000

Reduce worker exposure to respirable dust without interfering with bag-filling operations. Approach A dust control hood was developed which contains and captures dust close to its source and prevents it from entering the bag-filling operator's work place. How It Works A sheet metal hood is placed around the nozzle of the bag filling machine. The hood is connected through ducts to the plant exhaust ventilation system. Air pulled into the front of the hood and around the sides of the bag picks up dust generated inside the hood, and carries it to the dust collector. The size of the hood can be adapted to fit most fluidized valve-type bag-filling machines. The height of the hood depends on the bulk density of the product and weight of the bags being filled. The 14-inch-width of the hood allows it to be used on multi-nozzle baging machines spaced 16 inches on center. Only 2/3 of the bag is actually within the hood, and this allows easy operator access for placing the bags on the nozzle.

Jan 1, 1978

By R. E. Hall

When the criterion for control of scale prevention on the evaporating surfaces is made the conditions in the concentrated boiler water, then this control becomes an exact operation amenable to an accuracy commensurate with all other operations in the boiler room. The responsibility in boiler water conditioning, however, includes more than clean surfaces. Corrosion in feed lines, economizers and the boiler is a function of the condition of the later, and must be controlled. Steam line and turbine blading deposits must be obviated by the system of conditioning. By the chemical treatment employed, the amount and character of noncondensable uses in the steam must be controlled in accordance with the intended use of the steam. All. in all, the responsibility in boiler crater conditioning ends not with the entrance of the water into the boiler but with the passage from the boiler nozzle of steam, the dryness and rarity of which are defined by the uses to be made thereof. A clearer conception of the scope of boiler water conditioning can be obtained by reference to a diagram of the surfaces (Figure 1) at which it functions. Consideration of this diagram leads to the following outline for the problems of boiler water conditioning: (a) Prevention of scale formation on surfaces (1) In contact with water but at which no evaporation occurs. (2) At which evaporation is occurring.

Jan 1, 1926

By R. R. Backer

The Bureau of Mines, in cooperation with Washington Irrigation and Development Co. (WIDCO), evaluated the dewatering of fine coal-refuse slurry using chemicals and various types and combinations of drains in natural earth impoundments. About 40 lb of lime and 2 lb of polymer per ton of dry solids were mixed with the underflow from the preparation-plant thickener. Clear, free water was immediately liberated from the slurry. The percent solids by weight of the slurry increased from about 17 to 30 immediately, and after 5 days increased to 45 wt-pct. This indicates a threefold reduction in total volume after 5 days from 172 cu ft/ton solids originally to 56 cu ft/ton solids.

Jan 1, 1981

By D. Montagna

The Kroll-Betterton process for debismuthizing lead is based on adding calcium and magnesium to impure molten bullion to form solid Ca-Mg-Bi inter-metallic compounds that float on the surface as drosses. Present practice in industry is to hand-skim off these drosses, often followed by hydraulic pressing to squeeze out some of the entrapped liquid lead. In an effort to develop an improved technique, the use of an argon-shrouded dipping centrifuge to perform the required phase separation was investigated. Centrifugation experiments demonstrated that the bismuth content of an impure bullion could be lowered from an initial 0.5 percent down to 0.03 percent with a lead recovery of 90 percent, which is comparable to lead recovery after hand skimming of drosses in commercial lead-debismuthizing operations. Centrifugation provides better control in removing drosses, faster operation with less oxidation and relatively little fuming, and recovery of a lead bullion that approaches commercial specifications.

Jan 1, 1972

By M. Kanefsky, A. Q. K. Rajput

Two channel polarity coincidence and polarity difference statistics are analyzed. The signal, common to both channels, consists of sinusoidal bursts where the exact frequency of the signal is nearly known, but other parameters such as amplitude, phase, and pulse starting time are unknown. The noise inputs are dependent, narrow band, Markov processes. It is shown that the performance depends not only on the signal uncertainties but on the precise shape of the cross-correlation functions between the noise inputs. By using two polarity difference statistics in addition to the polarity coincidence statistic, it is shown that the decrease in performance, as well as the cost of hard limiting due to correlated inputs, can be made small.

Jan 11, 1981

By W. R. Reed

Drilling with water has the potential to significantly reduce the respirable dust concentrations generated from small-diameter rotary drills when drilling blastholes on surface mining operations. However, water adverseky affects tri- cone drill bits commonly used in surface drilling operations, causing excessive wear and premature replacement. Consequently, dry drilling with a dust collector system has the most widespread use in the industry. Tests have been conducted by the National Institute of Occupational Safety and Health (NOSH), Pittsburgh Research Laboratory (PRL) on a newly designed device for smaller diameter drills that separates the water from the bailing air before it reaches the bit and thus provides the cost benefit of dry drilling while providing the benefit of wet drilling for dust suppression. The water that is delivered to the hole with the bailing air is separated from the air by a proprietary mechanical device that is encased in a drill sub (short section of drill rod/pipe) located immediately behind the cutting bit. A cascade cyclone and a real-time dust monitor were used to sample dust emissions from the holes. Dust concentrations and silica content were measured when drilling dry versus drilling wet. The tests show that drilling with this water separating sub can reduce both measured dust emissions from the boreholes and visible dust around the drill rig.

By Eliot J. White

The physical properties and clay mineral content of the major oil-producing formations in the Powder River Basin of Wyoming were determined by analyses of cores from 100 wells. Interrelationships were established among permeability, restored water saturation, clay content, and bulk swelling capacity of the crushed sample and used to estimate the susceptibility of the formations to water damage. The ratio of water permeability to gas permeability (kw/ki) offers a convenient scale for semiquantitatively estimating the water sensitivity of sands. The irreducible water saturation was also found to have a similar relationship to the clay mineral content and the water sensitivity of the sands. The average relation of water permeability to gas permeability is different for each sand, as shown by the curves, and the relative positions of the curves indicate the degree of water sensitivity of each sand from which the susceptibility to water damage may be estimated. How accurately these estimates show formation behavior under field operations will not be known until studies of field performance can be made. The water permeabilities of the Muddy, Minnelusa, and Tensleep sands average about the same as the gas permeabilities, and these sands are classified as insensitive. The water permeabilities of the Sussex and Shannon sands, at the other extreme, are much less than the gas permabilities [when average ki is 30 millidarcys (md), kw is 6.1 md], and these sands are classified as highly water sensitive. The sensitivities of the five other sands are between these extremes.

Jan 1, 1962

By I. D. Shah

The copper-nickel ore of the Duluth Gabbro Complex in northeastern Minnesota is a large potential domestic resource of cobalt and platinum-group metals. However, because of the low grade of the primary metal values (0.5 pct Cu, 0.15 pct Ni), the private sector has assigned a relatively low priority to the development of technology for processing this ore, anticipating that mining probably would not begin until the mid-1990's. Furthermore, preliminary processing flowsheets considered by the mining companies centered on the primary metal values. As part of an effort to help provide the basis for technology to recover critical and strategic minerals from domestic resources the Bureau of Mines is investigating methods to recover all of the mineral values, in the Duluth Gabbro material, with particular attention to the byproduct critical minerals. A key step in this process is the removal of a relatively large amount of iron present in the bulk sulfide flotation concentrate to permit subsequent extraction of mineral values. This report describes a direct smelting method that removes most of the iron and produces a copper-nickel-cobalt matte, an intermediate product from which the metal values subsequently are separated. Copper, nickel, and cobalt grade and recovery data are presented for the direct smelting method. Test results showed that under certain conditions some of the mineral values reported to the slag, requiring slag cleaning to recover them.

Jan 1, 1983

By Mark R. Stephenson

Everyone knows that mining is a noisy job, but did you know that you are nine times more likely to lose your hearing than someone who works in a quieter job? If unprotected from noise on the job, by age 50, you will probably need hearing aids. Obviously, the best solution is to engineer out the noise, but that isn?t always im­mediately possible. Until mines are quieter, one way you can help save your vital sense of hearing is to use hearing protectors whenever the noise around you is hazardous. Even if you already have some hearing loss, you can use hearing protectors to prevent your hearing from getting worse. When loud noise is present, proper use of hearing protectors will help miners pre-vent most or all noise-induced hearing loss.

Jan 1, 1998

By R. H. Storch

The work described in this report was part of a Bureau of Mines program to appraise the titanium-mineral resources of Idaho. Part of the program included churn drilling of alluvial deposits that previous preliminary testing, primarily for rare minerals, had indicated to be potential sources of titanium minerals. The first spot churn drilling began in the Deadwood placer area, Valley County, Idaho, in July 1956 to determine both the amount and grade of the ilmenite, FeTi03. Ten holes, ranging in depth from 6 to 40 feet and aggregating 251 feet, were drilled; 54 samples were taken. The samples were sent to the Spokane field laboratory for concentration and visual estimation of the amounts of the more common minerals in the heavy sand concentrates. For specific determinations samples from each drill hole were composited and shipped to the Bureau of Mines laboratory in Albany, Oreg., where petrographic, quantitative X-ray spectrographic, and chemical analyses were made.

Jan 1, 1958

By Michael T. Nigbor

The Bureau of Mines assisted the Rocky Mountain Energy Co. in a pilot-scale in situ leaching experiment at Casper, Wyo., to determine if sulfuric acid can be used as a cost-effective alternative lixiviant (leachant) for uranium in situ leaching. This experiment, which lasted more than 2 years, is the first fully documented pilot-scale operation in which the leaching-restoration cycle was completed using sulfuric acid instead of the more common carbonate-bicarbonate leachant This report describes activities at the experimental site, presents extensive geochemical data from startup to site restoration, compares laboratory and field experiments, and discusses the environmental aspects of acid leaching. The data showed that sulfuric acid is apparently an effective leaching solution. Three to five grams of acid per liter of ground water resulted in a production solution grade of 80 to 100 ppm uranium. Restoration was successful, but required extended flushing. The pH was the last chemical parameterto return to baseline, requiring about 350 days. This was longer than was predicted in laboratory simulations. The data also showed that mobilization of toxic elements such as selenium, arsenic, radium, thorium, and molybdenum stayed within reasonable limits and quickly fell back to preleach concentrations during restoration.

Jan 1, 1982

By John Ward Smith

An analytical method developed by the Bureau of Mines to determine dawsonite, nahcolite, and nondawsonite alumina (called excess alumina) extractable from Green River Formation oil shales is presented. The method requires water extraction of nahcolite followed by HCI-extraction of dawsonite and an unidentified mineral yielding excess alumina from the water-leached residue. Instrumental determination of sodium in the water extract and sodium and aluminum in the HCI extract measures the sample's content of the minerals. Detailed evaluation shows the method to be adequately specific, precise, and reproducible and free from uncorrectable interferences. The method's results define precisely the production of sodium carbonates and alumina possible from a sample of oil shale and the interval it represents. Shale-oil yields, nahcolite contents, and yields of extractable alumina determined on 83 samples representing an 821-foot section of dawsonite-nahcolite-bearing shale from .Colorado Corehole No.3, drilled in the north part of Colorado's Piceance Creek Basin, are presented. These samples resulted in nahcolite contents to 53.3 percent, oil yields to 48.3 gallons per ton, and alumina yields to 5.80 percent. Use of these data to evaluate the production potential of a section of the formation are suggested.

Jan 1, 1969

The notion of wayfinding, as conceptualized by planners, geographers, and psychologists, denotes the ability of an individual to move from one point to another through physical space. In order to achieve this movement, a person relies on a cognitive map of spatial representations [Passini 1984]. Which features of this cognitive mapping will be stressed depend, in part, on the researcher's perspective. A planner, for instance, would tend to emphasize the effect of physical structures on mobility. A psychologist, on the other hand, might focus on individual differences in how human minds encompass and represent physical space [Evans et al. 1984]. There is yet another dimension to wayfinding that needs consideration, and it rests upon the idea that reality, as experienced by human beings, is mediated: "[People] have preselected and preinterpreted this world by a series of commonsense constructs ... which help them find their bearings in their natural and socio-cultural environment and to come to terms with it" [Schutz 1967]. These "common sense constructs" are arrived at socially and constitute the agreed-upon schemas that guide people's everyday activities. According to this principle, cognition is governed by some nonlogical factors that reflect not only individual procedures but collective ones as well. These group strategies, which are shaped by shared rules and values, influence "the information gathered, the ways it is processed, the inferences that are drawn, the options that are being considered, and those that are finally chosen" [Etzioni 1992]. From this perspective, cognitive maps, rather than being individual-centered templates of environmental images [Rovine and Weisman 1989] or representations of spatial relationships [Evans 1980], are partially group-centered schematic processes. As such, they are subject to reinterpretation, revision, and outside intervention [Kaplan and Kaplan 1982]. As intermediaries between the environment and behavior, cognitive maps serve as bases for decision-making. Traditionally, it has been assumed that good maps facilitate correct decisions, which in turn leads to optimal performance during wayfinding [Hunt 1984]. Given the argument that there is a social (non¬cognitive) facet to cognitive mapping, however, this image of a cognitive map as some sort of static reference construct that motivates individual action is too narrow and mechanistic. If cognition involves less a knowledge of the environ¬ment than it does the process of "giving it meaning through imposing an order on it" [Rapoport 1976], then wayfinding behavior is not j ust a function of setting and individual differences, but is also a function of one's "normative-affective" structure [Etzioni 1992]. Rapoport [1976] used such an assumption as the base for a set of hypotheses about the connection between "external demands" and "organismic factors." One significant assertion deriving from Rapoport's ideas is that environmental

Jan 1, 2000