Search Documents

By J. S. Tosh

An equilibrium study of the system potassium carbonate, potassium bicarbonate, carbon dioxide, and water has been conducted with solutions of 20-, 30-, and 40-percent equivalent potassium carboaate concentrations. These equilibrium data cover the operating range of the hot carbonate scrubbing system for removing carbon dioxide from gas mixtures. Such data are necessary to establish the limits of purification and are used to design absorption and regeneration towers. Values of K in the relationship K = (KHCO3)2/(K2CO3)PCO2 were determined for higher temperatures of 70" to 140° C. and greater concentrations, I 20 to 40 percent, than employed by previous investigators. For the 20- and 30-percent concentrations, K is constant at a given temperature; thus, once K has been determined the equilibrium pressure of carbon dioxide can be calculated for any conversion. Variation of & values with changing conversion was observed with the 40-percent solutions, so that equilibrium calculated pressures are less reliable from average K values.

Jan 1, 1959

By R. E. Mussler

As part of an overall goal to develop technology that can maintain an adequate supply of minerals to meet national economic and strategic needs, the Bureau of Mines is evaluating a method for selectively extracting nickel and cobalt from low-grade domestic laterites. The method involves electrowinning to recover the metals in pure form; therefore, preliminary laboratory-scale electrowinning tests were conducted in both a nondiaphragm and a diaphragm cell to determine the effect of variables on energy efficiency under controlled conditions. Electrolytes were generally reagent-grade sulfate solutions that were prepared to simulate electrolyte that could be obtained by stripping nickel-and cobalt-rich solvent extraction reagents. Limited tests were conducted with electrolyte generated from laterite leach solutions. Electrical energy consumption in a nondiaphragm cell was 2.06 kwhr/lb Ni with the cell operated at 50° C, a cell feed of 90 g/l Ni, a pH of 3.5, an extraction of 3.2 g/l, and a cathode current density of 20 amp/ft2. The energy requirement decreased with increasing concentration and temperature, and increased with increasing. extraction and current density. At 50° C, energy consumption in the nondiaphragm cell was 21 pct greater than in the diaphragm cell, but it was only 5 pet greater at 65° C. For this reason and because of overall cost considerations, operation at 65° C with the nondiaphragm cell was preferred. Smooth sheets of cobalt were obtained by electrowinning in a nondiaphragm cell at selected temperatures from 50° to 85° C and with cobalt concentrations from 55 to 87 g/l. The energy consumption (1.48 kwhr/lb) was 22 pet lower with a cobalt concentration of 75 g/l and a cell temperature of 65° C than with a cobalt concentration of 55 g/l and a cell temperature of 50° C.

Jan 1, 1981

Flexible hoses with rated working pressures up to 40,000 psi are used when high-pressure water jets are employed to cut rock or improve the performance of mining machines. Hose failures at such high pressures can result in serious injuries to workers. The Bureau of Mines used fatigue and burst tests to investigate the failure modes of high-pressure hoses at their rated working and burst pressures. Fatigue failure, at rated working pressures, occurred when the inner liner of the high-pressure hose broke, allowing water to seep through the wire wrapping, although the reinforcement wires did not break. At the burst pressure, all hoses failed catastrophically when the reinforcement wires broke. Low-pressure hoses placed over the high- pressure hoses for safety failed to contain water released by catastrophic failure.

Jan 1, 1987

By Earl L. Phillips

The Bureau of Mines conducted laboratory tests on samples of pozzolanic-cement concrete to develop a low-strength backfill. Results show that support costs can be lowered by replacing a portion of the portland cement in mine backfill with pozzolan (fly ash) and lime. Unconfined compression tests on various ratios of fly ash to cement in 84 samples produced compressive-strength curves that can be used to estimate the best backfill mix for any mine.

Jan 1, 1981

By S. A. Matthes

This Bureau of Mines report describes a system for the dissolution of metal and mineral samples using a microwave heat source. Samples and an acid mixture are placed in sealed polycarbonate vessels. The vessel contents are heated using microwaves, digested for 2 min, and quickly cooled. After the solution is brought to a final volume, the vessel contents are heated an additional 2 min in the microwave oven. Using this method, a slag, a feldspar, and a Ni-Cu alloy were dissolved and analyzed by atomic absorption spectroscopy. Values obtained for Na, K, Cu, Ni, Si, Mg, Mn, Ca, Al, and Fe agreed with certified values and had an average relative standard deviation of 1 pct. This system results in a significant savings in time and expense over traditional methods of sample dissolution, and is ideal for preparing solutions for analysis by atomic absorption, plasma optical emission, or X-ray spectroscopy.

Jan 1, 1983

By L. C. IlsLey

The Burrell methane indicator developed by Col. G. A. Burrell in 1915 was modified during 1918 to the " insulated type " Burrell indicator . Though this instrument has been used in mines since its first introduction , it was not formally approved as safe and efficient for use in gaseous mines until March , 1922. The indicator is built by the Mine Safety Appliances Co. , Pittsburgh , Pa . Approval No. 800 has been assigned to this company covering the device in the form approved . The principle of the Burrell indicator is fairly well known . It works on the same principle as the Haldane apparatus - measuring by means of a graduated scale , the contraction resulting from burning the methane content of an air and gas sample . A given aniount of the mine atmosphere to be tested for methane is taken into the indicator . This sample is then thoroughly shaken with the water in the indicator for one minute . The methane in the sample is now burned for two minutes by a heated platinum coil , which is energized by a small storage battery containing two Edison cells connected in series . After the glower or coil has burned for two minutes , it is disconnected from the battery , and the indicator is again shaken for The amount of contraction observed by reading the height the water rises in the U- tube of the indicator , which is calibrated to register the percentage of gas in the sample . The indicator as approved by the Bureau of Mines is equipped with an Edison M- 8 mine- lamp battery , and with a glass and scale graduated from zerɔ tɔ four per cent methane . The approval of a corbination service that is , an attachment for giving illumination from the same battery from which the platinum glower is operated has been withheld pending the development of a battery with larger capacity . - Under laboratory operating conditions , a single glower was capable of making at least 20 determinations if proper precautions were observed with respect to the use of freshly charged batteries . A battery should be allowed to stand off charge several hours before using in an indicator , as the peak voltage of a freshly charged Edison cell is abnormally high and is likely to send enough current through the glower to melt the platinum wire . Fifty-seven satisfactory operations were obtained from a completely charged battery . The point where the voltage of the cell fell below 2.3 volts with the glower attached was taken as the lower limit of successful operation . A voltage less than 2.3 does not permit the lower to burn at a temperature that will completely burn the gas in the air , thus giving a false indication .

Jun 1, 1922

By Foster Fraas

In this Bureau of Mines report, use of the photoemission of electrons to produce electric charges for the electrostatic separation of sonic dispersed minerals, which had previously been ground to pass a 43µ-opening sieve, is demonstrated. It appears that many of the oxides, carbonates, sulfides, and arsenides will respond to photoemission. Minerals least responsive are the oxides of silicon, the oxides of aluminum, and minerals that have a high concentration of these oxides. Although several synthetic ore mixtures did not yield to complete separation in a one-stage operation, it is probable that preliminary neutralization of the initial electric charges produced by powder dispersion will provide complete separation. That the separation can be carried out in air and without the use of reagents or heating, which are required in the present practice of electrostatically separating coarse granular feeds, is of special significance.

Jan 1, 1972

By K. D. Plants, J. H. Holden, L. F. Willmott

Pulverized high- volatile A bituminous coal was gasified with oxygen and superheated steam in a pressure - gasification pilot plant equipped for steampickup feeding . The pilot plant operated satisfactorily at relatively high steam- to - coal ratios , but steam- to - coal ratios could not be reduced much below 0.5 lb / lb without condensation of steam or softening of the coal . Carbon gasified , gas composition , and coal and oxygen requirements were essentially the same as for a pilot plant equipped with a fluidized coal feeder . Average results from the pilot plant equipped for steam- pickup feeding were coal requirement , 37.3 lb/M ( 1,000 ) scf of CO + H₂ produced ; oxygen requirement , 358 scf /M scf CO + H₂ produced ; and carbon gasified , 87.7 percent .

Jan 1, 1964

By M. G. Zabetakis

The method of moving averages was found useful in assessing the nature of methane emission in coal mines. Emission rates were influenced markedly by the presence of abandoned oil and gas wells in the vicinity of the mine. Such wells appeared to increase the flow rate of methane into the mine by a factor of 2 to 30 in an active mine in the Pittsburgh coal seam.

Jan 1, 1972

Develop a down-hole replaceable diamond core bit that will reduce overall drilling costs and increase total available drilling time per hole. Approach A one-piece diamond core drill bit of unique geometric shape has been designed, fabricated and field tested. The bit can be withdrawn (or replaced) from the bottom of the well-bore without removing the drill rods from the hole, saving a significant amount of non-productive drilling time. How It Works The replaceable bit system consists of two basic subsystems: the removable core bit, and the equipment necessary to replace the wornout bit without pulling the drill rods out of the hole. The geometric configuration of the bit is that of a one-piece diamond studded cutting element created by "slicing off" two parallel sides of a conventional diamond cone bit. This geometric configuration, along with some minor modifications to the outer core barrel, allows the bit to be rotated in two planes and, with the retraction-insertion tools, raised or lowered through the interior of the drill rods using a conventional wire-line system. For example, to retrieve the bit, a retraction tool is lowered through the drill rods using a conventional wire-line system and at the hole bottom, the tool automatically orients itself within the outer core barrel.

Jan 1, 1981

By J. E. Schiller

The Bureau of Mines has investigated the surface charge of amphibole asbestos fibers and nonasbestiform cleavage fragments, as part of the Bureau's fundamental studies to provide new knowledge on the physical and chemical properties of the amphibole minerals. Microelectrophoresis was used to measure the electrophoretic mobilities, in water, of particles from six asbesti-from amphiboles and seven nonasbestiform amphiboles over the pH range of 5 through 9. The particles generally ranged in size from 2 to 5 µm wide by 10 to 30 µm long. The isoelectric point was determined for four of the minerals, and values were found to be between pH 3.5 and pH 5. The minerals studied had zeta potentials that generally ranged from -25 to -so mv in neutral solution. Attachment of colloidal positively charged AgI was also studied as a means of determining surface charge. Scanning electron microscopy of amphibole particles that had been in contact with aqueous AgI showed equal attachment of AgI to asbestos fibers and to cleavage fragments; the extent of AgI coating was the same for both. The electrophoretic mobilities of asbestos fibers were essentially the same as those of elongated cleavage fragments of the same aspect ratio (particle length divided by width). Blocky particles from both asbestiform and nonasbestiform specimens had lower mobilities.

Jan 1, 1980

By Todd M. Ruff

Researchers at the National Institute for Occupational Safety and Health (NIOSH) are studying methods to prevent workers from being entangled in machinery used at mining operations. An analysis of mining accidents in the United States that resulted in a fatality or permanent disability from 2000 through 2005 showed 438 severe incidents that involved contact with machinery or equipment, an average of 73 per year. Researchers determined that the most common machinery involved in these severe accidents was conveyors. Also, a significant portion of the accidents occurred during machine maintenance and repair. Researchers are focusing on improved methods to prevent unintentional machine startup during maintenance activity and methods to detect workers near moving machine components. One new technology that shows promise for this application is intelligent video. Popular in the surveillance and security industries, these systems use cameras and computerized video analysis techniques to automatically detect the presence of people in preset zones within the camera?s field of view. A preliminary study has been initiated to determine if this technology could reliably detect the presence of workers in hazardous locations near machinery. Possible advantages of the use of this technology include improved detection zone demarcation and improved ability to distinguish between hazardous and non-hazardous proximity, compared to conventional proximity sensor techniques. Initial tests to detect a person near a conveyor system in daylight conditions showed promising results. A description of the technology, test procedures and results, implementation challenges, and future research needs are discussed.

Jan 1, 2008

By B. E. Davis

Over 80 pct of domestic phosphate rock, which is the starting material for phosphorus-containing fertilizers, comes from central Florida deposits. As K-her grade deposits are depleted, lower grade phosphate ores containing 'Mg0 in the form of dolomite are encountered. Treating high MgO ores with present beneficiation technology will not yield a concentrate meeting specifications for acidulation. The Bureau of Mines conducted research on three high-MgO phosphate samples from south Florida. The sales contained, in percent, 5.4 to 10.2 P205, 1.9 to 7.6 MgO, and 35.3 to 60.1 acid insolubles. A technique of sizing, grinding, desliming, scrubbing, and redesliming was used to produce a feed suitable for continuous flotation studies, A conventional fatty acid-fuel oil rougher flotation followed by two to three cleaner stages resulted in concentrates containing, in percent, 30.7 to 31.3 P205, 0.6 to 1.3 MgO, and 2.5 to 4.8 acid insolubles. The P205 recovery from the flotation feed ranged from 55.1 to 89.7 pct.

Jan 1, 1984

By Seymour Wasserman

To develop noise control designs for secondary crushers in Taconite plants. Taken into consideration: 1. Acoustical criteria 2. Day-to-day operational considerations and maintenance accessibility 3. Materials of construction 4. Adaptability of design to other Taconite plants having crushers 5. Cost of noise control treatment.

Jan 1, 1977

By Gertrude N. Greenspoon

Legislation and Government Programs.-The Occupational Safety and Health Administration (OSHA) held public hearings in early 1975 on proposed standards for exposure to inorganic arsenic. The findings obtained at the hearings will be considered to promulgate emission standards. Domestic Production.-Arsenic trioxide (As203) was produced domestically only at the Tacoma, Wash. copper smelter of ASARCO Incorporated. Production data cannot be published. Output rose 9% over that of 1974, shipments were less than half those of 1974, and stocks rose 31 %. Production of arsenic metal, begun by ASARCO in August 1974, continued in 1975.

Jan 1, 1977

By John M. Devine

The oxygen bomb-is used extensively for determining sulphur in petroleum, although it has been suspected that the results obtained with this method are somewhat lower than the true varies. In this paper are compared the results given by the oxygen-bomb and Carius methods, the latter being generally accepted as the standard procedure for the determination of sulphur in organic compounds. The Carius determinations given hero were made in connection with a special study of this method.4 Only petroleum oils of the less-volatile type are covered in the present work. Summary and Conclusions. When used with oils containing 2.3 to 0.15 per cent of sulphur the oxygen-bomb method gives results that are consistenly if slightly lower than those obtained with the Carius method. This variation, for the oils used, amounts to 3.1 per cent (on tae basis of sulphur present) for the sample containing 2.47 per cent of sulphur, and gradually increases (as the percentage of sulphur in the oils decreases) to 7.3 per cent for the oil containing 0.15 per cent of sulphur. With the oils studied the presence of ammonium nitrate in the bomb does not influence the results materially.

Jan 1, 1928

By G. R. Hopkins

"Summary An apparent decline in fuel efficiency at refineries, which first became came evident in 1930 and continued through 1933, was checked in 1933 when the average amount of heat needed to refine a barrel of crude oil amounted to 660,000 B.t.u. This compares with an average requirement of 692,000 B.t.u. In 1932 and with a low of 639,000 B.t.u. in 1929. (See fig. 1.) The improvement in fuel economy in 1933 probably was closely related to the increase of 5 per cent in crude runs to stills. As much of the fuel burned at refineries is utilized for purposes other than under crude-oil stills and in relatively stable amounts, it is evident that a material increase in crude runs will usually reflected in a decrease in average fuel requirements. Another factor which has influences fuel economy at refineries in the past is the trend in cracking, a refining process requiring more than the average expenditure of heat. In 1933 production of gasoline by cracking increased slightly, but no appreciable rise in heat requirements resulted as an equivalent amount of fuel was saved in improved technique, particularly in the field of heat exchange.Since the beginning of the refining industry, the transition in fuels has been from solid to liquid to gaseous; in other words, the leadership was first held by coal, then passed to oil, and is now held by gas. In 1933, 54.7 percent of the total heat units generated came from gas, 39.0 percent from oil (including acid sludge), and 6.3 percent from coal and coke. The principal change in the relative importance of the various refinery fuels in recent years has been the rapid growth in consumption of refinery or still gas at the expense of all the other common fuels. Still gas owes its ascendency to its cheapness and availability, and probably it would have become the primary refinery fuel years ago if recovery methods had been perfected. The relative importance of coal showed a small increase in 1933, the first gain recorded since these surveys were inaugurated in 1925. The increase in use of coal was undoubtedly due to increased operations at plants using it,"

Feb 1, 1935

By L. E. Schultze

The Bureau of Mines operated a mineral recovery unit to recover metal values from post-flash geothermal brines from the Salton Sea known geothermal resource area as part of its research into the use of plentiful resources. The brine was available for metals recovery after its heat content had been used to generate electricity. The brine source was treated with lime to precipitate the contained iron, manganese, lead, and zinc before injection of the heat-depleted brine into the underground reservoir. Data are presented on the effects of process variables, such as rate and method of lime addition and air oxidation versus air exclusion. Variations in precipitation of metal values, composition of precipitates, effectiveness of slurry thickeners, and methods of treating the precipitates to recover metal values are discussed.

Jan 1, 1982

By M. J. Kovalik

Illinois No.6, a high-volatile B coal of low fluidity, was blended with fluidized-bed char and coke breeze to improve the strength of the coke obtained from carbonizing this coal. Twenty-one tests, selected from those made in the small-scale Hanson carbonizer, were carbonized in the BM-AGA 13-inch-diameter, cylindrical retort, with a coal charge of about 90 pounds; the strength of the cokes was determined by the standard ASTM tumbler test. Using the same procedure, 10 tests were made with High Splint, a high-volatile A coal from Harlan County, Ky. Carbonization of the blends produced larger and stronger cokes than did the Illinois No.6 coal singly. The optimum blend contained 6 percent each of char and coke breeze. Further improvement in coke strength was realized by either preheating this blend prior to carbonization or by adding a small pro-portion of a premium blending coal. The former method could possibly eliminate the use of premium coking coals in blends with Illinois No. 6 coal to make an acceptable metallurgical coke. Except for no improvement in coke strength by preheating, results for High Splint coal showed behavior similar to that of the Illinois No.6 coal.

Jan 1, 1973

By D. Harrington

In recent years over 100,000 persons have been killed annually in the United. States by accidents; about one-fifth of these have been workers in some of our industries; about one-third have been killed by motor vehicles; about another third have mot death in home accidents, chiefly falls, burns, scalds, explosions, poisons, asphyxiations, suffocations, cuts, scratches, and so forth; and the rest have been killed in public accidents, excluding those caused by vehicles but including accidents on railroads or electric cars, drowning, and deaths by firearms and. other means. Definite statistics on nonfatal accidents are not readily available, but at least 10,000,000 fairly serious accidents probably occur in the United States annually. The latest industrial-accident statistics are obtainable from 1935 National Safety Council publications, in which annual industrial fatalities are divided about as follows (in round numbers): Agriculture, 4,500; trade and service, 4,500; construction, 3,100; transportation and public utilities, 2,900; manufacturing, 2,600; mining, quarrying, petroleum, etc., 1,900.

Jan 1, 1938