Search Documents

By M. J. Sapko

The Bureau of Mines conducted laboratory-scale flammability experiments to investigate the possible use of water spray systems for inerting or quenching mine-gas ignitions, such as those encountered at the working face of a coal mine. The inerting results for premixed methane-air-water mixtures indicated that water droplets of less than 10 µm tend to be as effective as the vapor. Water requirements for inerting such mixtures were much smaller than those for quenching the sustained flame propagation by the application of water sprays. The minimum water mass concentration for quenching methane-air flames increased linearly with increasing droplet diameter (surface weighted mean) and decreased with increasing spray temperature, whereas the droplet surface area required per unit volume was essentially constant for a given gas mixture composition. Data extrapolations indicated that a quenching system may be feasible for the longwall mining application.

Jan 1, 1977

By E. J. Gleim

A list of permissible mine equipment, tested and approved previous to January 1, 1942, was published In Bureau of Mines Information Circular 7207.3/ The present list covers additional equipment approved during the calendar year 1942. The items have been numbered to indicate the order in which each type of machine or device was approved in its particular classification. Thus, Information Circular 7207 gives four air compressors on the Bureau's active list, and the present circular gives the fifth to be approved. Items 90 and 94 under Loading; Machines land Conveyors also appear in Information Circular 7207. These numbers are repeated hero to show that approval was granted during 1942 for additional voltages on machines previously listed one voltage only. Equipment listed in these circulars is approved by the Bureau of Mines only when found upon inspection and test to comply with minimum standards of safety as outlined in schedules prepared on the basis of many years of experience in dealing with safety problems of the coal-mining industry. The use of such equipment in mines known to be gassy, as well as in those which may become so, is earnestly recommended in the interests of safety. This circular is published so that the industry may be kept informed as to the many types of machines, devices, and lamps that arc available for reducing explosion and other hazards incidental to coal mining. The present paper and Information Circular 7207 together give the complete list of all available permissible .Mine equipment.

Jan 1, 1943

By James R. McVey

A new method for measuring deformations of rock surfaces in underground excavations has been suggested by Dr. James Powell of Brookhaven National Laboratories (BNL) and subsequently developed and successfully demonstrated in a mining environment by the Federal Bureau of Mines, Spokane Mining Research Center (SMRC) and Brookhaven National Laboratories. The system uses 35-mm photography of targets strategically located on surfaces of interest, such as across the roof and on the sides of a mine drift or tunnel. The optimum tar-get, as determined in this investigation, consists of a white ?X? made with 1/8-inch-wide reflective tape on a black 6-inch square. Photographs, taken in pairs from two separated camera positions and at regular time intervals, were analyzed at the Bureau by hand and at Brookhaven National Laboratories using techniques and equipment similar to those used in cloud chamber film analysis. Test results show that deformation-measurement accuracies of better than ±0.020 inch in a drift that is 20 feet wide can be expected. This degree of accuracy, plus providing displacement data in the X, Y, and Z directions (rather than the one direction formerly possible), makes this a noteworthy and useful tool for industry as well as for mining research.

Jan 1, 1974

By M. Kanda, J. W. Adams

A system for measuring amplitude probability distributions (APD’s) of electromagnetic noise in coal mines is described and typical APD’s from an underground coal mine are presented. The APD is a basic statistic required for the design and analysis of communication systems, especially those intended for use in noisy environments, and where neither overdesign nor underdesign is acceptable. The rms and average field strengths are obtained by integration of the APD, and examples are shown at several frequencies. All field strength levels are given in absolute units. Selected frequencies cover the range from 10 kHz to 32 MHz.

Jan 1, 1973

By B. R. Mohal, F. F. Aplan, S. Chander

"The wetting behavior of coal has been determined in the presence of nonyl and octyl series of nonionic surfactants containing polyethoxy groups of different sizes. The wetting behavior was determined by a modified Walker technique and contact angle measurements. The results show that the wetting rate of coal varies with coal rank, structure of the hydrocarbon chain and number of ethoxy groups in the hydrophilic group of the surfactant. A close relationship has been observed between the wetting rates and the short-time advancing contact angles.INTRODUCTIONNonionic surfactants are used in many applications to improve wettability of solids. They can be used as dispersing agents [ 1 ] or dust suppressants [ 2-5] and to control the flotation, flocculation, filtration and flowability of particulates. This study was undertaken to study the effect of a series of nonionic surfactants on the wetting behavior of coal. Two series of surfactants, namely, ethoxylated nonyl and octyl phenols were used. The nonyl phenol series contains a linear hydrocarbon chain containing nine carbon atoms ( CH3 ( CH2 ) 8-C6H4-( OC2H4 )""' where n is the number of ethoxy groups). The octyl phenol series contains a branched hydrocarbon chain containing eight carbon atoms ( ( CH3 ) 3CCH2C ( CH3 ) 2-C6H4-( OC2H4)"").Initial wetting rates - modified Walker techniqueWalker et al. [ 6] developed a sink test to determine the wettability of coal particles. In this technique, coal particles are dropped individually onto the surface of surfactant solutions of different concentrations, and the most dilute concentration in which coal would sink ""instantaneously"" is determined. This technique is a variation of a procedure initially developed by Draves and Clarkson [ 7] to determine the effect of surfactants on wettability of cotton fibers."

Jan 1, 1989

By R. S. DeCesare

Operation of the Bureau of Mines raw refuse continuous separation pilot plant is described, including modifications made to plant equipment for improved performance. Products recovered from refuse, many of which have been evaluated by other laboratories and private firms, are discussed. Sampling procedures used in the pilot plant and detailed data obtained from processing refuse from 13 municipalities are presented in appendixes. Fuel evaluations made on combustible fractions of refuse from the various municipalities are also presented. Information and data obtained at the pilot plant have been used to assist many municipalities in solving their urban refuse problems.

Jan 1, 1980

By J. S. Dunning

A primary goal of the Federal Bureau of Mines is to minimize the requirements for scarce mineral commodities through conservation and substitution of more abundant elements, such as iron and molybdenum. One example of this is the research effort to devise substitute materials for specialty alloys, thereby conserving nickel and chromium in high-volume stainless steels. As a possible substitute for the solid solution strengthening of chromium and nickel, the precipitation hardening characteristics of a number of binary iron-based systems in which Laves phase precipitates, such as Fe2Mo, are formed were investigated. Several hardening responses were observed, but none were ideal. The Fe-Ta binary system had the highest magnitude of hardening, even with low alloy additions, and the Fe-Mo system had unique stability at temperature. Accordingly, the Fe-Mo-Ta system was selected for study to determine if a ternary Laves phase could combine high hardening with long-term stability at elevated temperature. Hardening and stability were reflected in excellent elevated temperature, tensile, and stress rupture strengths. Future research will study ternary systems based on more abundant resource materials, such as the Fe-Mo-Ti system, together with additions, such as aluminum and minimal chromium, to provide oxidation resistance.

Jan 1, 1979

By H. O. Poppleton

This Bureau of Mines study was made to investigate a possible method for selectively removing the Si02 component of silicate minerals and ores. Of specific interest were aluminum ores and zircon. Methods are described for removing Si02 from these ores as volatile silicon sulfides by treating the ore with sulfur and carbon; with sulfur, carbon, and a reducing gas; or with sulfur compounds and carbon. Comparative results are also given for the desilication of some of the ores with carbon alone to form volatile silicon monoxide. The silica component can be removed partially from bauxites at temperatures above the sublimation temperature of SiS (940° C) by treatment with carbon, sulfur, and methane; however, it is more difficult to remove the silicon from kyanite, manganese silicate, red muds from aluminum processing, kaolinite, lateritic nickel ores, and zircon. Complete desilication requires temperatures ranging from 1,100° C for bauxite to 1,450° C for zircon. Although the high temperatures required and the undesirable metal sulfides produced eliminate practical application of this method using present technology, the Bureau is reporting this data so that they will be available to future investigators.

Jan 1, 1974

By William H. Schiffbauer, William D. Mayercheck, August J. Kwitowski

This report summarizes work sponsored by the Bureau of Mines in the development of a remote operating system (ROS) for controllng a thin-seam continuous miner (TSCM) 500 feet or more distant from the extraction face. Detail s are provided on ROS subsystems including the continuous miner, video equipment, controls and displays, the electronic control system, and the operator station.

By George McCaa, H. C. Howarth

"During recovery operations following a recent coal-mine explosion, 12 small fires were encountered near the break line of pillar extraction in a large panel. All of the fires except one were quickly extinguished by the rescue and recovery parties. This fire had found its way into a large quantity of loose material at a corner of the cut-through between two rooms, about 100 to 150 feet from the break line of an extensive goaf; had it been necessary to seal the fire, the inclusion of this break line not only would have made the work difficult but would have made the section hazardous as it probably would have given off gas. The fire covered a floor space of about 100 square feet and when discovered was burning briskly, with the flame extending to the roof at a height of 3 or 4 feet; it was the cause of much apprehension on the part of those in charge of the recovery operations and resulted in delaying the work considerablyThe object of this article is to describe in detail the method by which the fire was brought under control and finally extinguished, so that other persons encountering similar conditions may have the benefit of the experience.When the fire was discovered a request for rock-dust, fire extinguishers, and other fire fighting equipment was telephoned to headquarters on the surface. The promptness with which fire fighting equipment and material was provided was a big factor in finally extinguishing the fire and illustrates one of the many advantages of a good organization for fire-fighting. Material was transported in mine cars to a point on the main hauling road about 1,200 feet from the fire. It was then carried to the scene of activity by workmen. The first material to be delivered at the fire was a number of fire extinguishers of various types. The contents of 30 to 35 of these were discharged on the fire and with the aid of a small quantity of rock-dust were sufficient to smother the flame temporarily. It was the opinion of several persons who were present when the fire extinguishers were used that the acid-soda type of extinguisher gave more effective results than the two or three other types used.When the contents of all of the fire extinguishers had been exhausted the fire was temporarily smothered, but as there appeared to be danger that the flame would burst forth again, means for completely extinguishing the fire were"

Feb 1, 1929

By K. K. Kelley, W. W. Weller

This report contains experimentally determined heat capacity data for four crystalline sulfides -- AsS , GeS , NiS , and Ni3 S₂ -- over the temperature range from 50 ° to 298.15 ° K. The heat capacity data were used to evaluate the entropies of the sulfides at 298.15 ° K. Entropies of formation from the metals and rhombic sulfur and from the metals and diatomic sulfur gas are also included .

Jan 1, 1964

By Richard G. Burdick

This Bureau of Hines report describes an interface between a minicomputer and peripheral device, The logic used to develop the device is discussed briefly, after which the device is described in detail; complete construction and operational details are given. The report should aid both in duplicating this device and in designing similar devices for different uses.

Jan 1, 1975

By D. B. Dow

"Natural gas-gasoline is made by collecting in the liquid state the condensable hydrocarbon vapors that exist in different natural gases in varying amounts. In the richer type of natural gas the gasoline is generally recovered by compression and cooling. If exceedingly high pressure or low temperature is used, there is dissolved in the gasoline a large amount of very volatile material, which evaporates rapidly at atmospheric temperature and pressure.In the leaner type of natural gas, the gasoline vapors are selectively absorbed from the permanent gases by passing the natural gas through an absorbing oil. The gasoline is recovered by distilling the saturated oil, and as compared with ""compression"" gasoline is of high Baume' gravity and low vapor pressure. Before a volatile gasoline can be transported in tank cars, it is necessary to decrease its volatility in order to lessen the risk of fire or explosion, as well as to prevent excessive evaporation in transit. This can be accomplished either by weathering the gasoline, or by blending it with a more stable material, naphtha being commonly used in the weathering process the more volatile portions of the gasoline are allowed to evaporate and the losses in volume are very large, therefore, blending is preferable, wherever possible.It is very difficult, however, to produce by blending, in gasoline plants, a motor fuel which is equal to straight-run refinery gasoline. In order to make a blended motor fuel of a grade equal to straight-run gasoline, only a small percentage of natural gas-gasoline can be blended with the naphtha, consequently it is customary to blend the gasoline with only enough naphtha to enable It to be shipped to an oil refinery when the material is again blended to form a finished motor fuel."

Sep 1, 1921

By L. A. Neumeier

The Bureau of Mines evaluated the properties and anisotropy in properties of rolled Zn-Ti and Zn-1.0 wt pct Cu-Ti alloys containing up to 0.36 wt pct Ti. Finish rolling was at varied temperatures to total reductions as high as 92 pct. Alloy properties are very sensitive to various combinations of composition, rolling temperature, and reduction. Properly rolled Zn-1.0 Cu-Ti alloys are superior in strength to Zn-Ti alloys. Conditions are described that lead to best tensile properties. Creep resistance for Zn-Ti alloys decreases with increased rolling temperature when finish rolled to 92-pct total reduction: but not when finish rolled to 33- or 67-pct reduction. Creep resistance for 7n-1.0 Cu-Ti alloys improves with increased rolling temperature to about 480° F. Heavily cold-rolled Zn-1.0 Cu-Ti alloys have fine grain sizes and poor hardness, tensile, and creep properties, but high ductility. Thermal expansivity is markedly affected by the copper addition. Data show the anisotropy of tensile, creep, and thermal expansivity properties. Large idiomorphic crystallites of TiZn15 appear in both Zn-Ti and Zn-Cu-Ti alloys when more than about 0.2 pct Ti is present. A new Zn-Cu-Ti intermediate phase was also identified. Empirical equations are presented relating creep rates with major process variables.

Jan 1, 1971

By Guy E. Dent, Robert S. Sandford, W. T. Millar, Hugo E. Kuehn

"INTRODUCTION AND SUMMARYDuring the latter part of 1943 a magnetometric survey was conducted by the Geophysical Division of the Bureau of Mines at the mine, Putnam County, N. Y., in an endeavor to locate a segment of the body that reports state was cut off by a fault. The Mahepac mine was abandoned about 1895 after producing nearly 1,000,000 tons of high-grade magetite iron ore. The results of the investigation indicate the termination of the ore body by ""pinching"" or a displacement of such magnitude as to place any extension at a considerable distance the original ore body. This report describes the work done on the project and presents the data obtained. ACKNOWLEDGMENTSThe Bureau of Mines has been investigating deposits of critical and essential minerals in the United States and Alaska since 1939. The Mahopac mine was visited by W.T. Millar, an engineer of the Bureau of Mines, on June 5, 1943, accompanied by Dr. William Agar of the Federal Survey, and again on July 29, 1943, accompanied by Dr. A. F. Buddington and H.F. Hawkes, both of the Geological Survey.The mineral investigation was under the general supervision of Paul M. Tyler, formerly regional engineer, Eastern Region; J. D. Bardill, formerly district engineer; and Dr. F.W. Lee, formerly chief. Division, Geophysical Exploration. The work was done under the immediate supervision of W. T. Millar, project engineer. The Geophysical Survey was made by Hugo Kuehn and Guy E. Dent."

Sep 1, 1948

By Lloyd A. Morley, Robert Stefanko

Before going directly to the analysis, it would be good to summar¬ize explosion-proof container approval methods. Both Magison (52) and Short (84) state that in general practice, the systems are certified for: 1. a rugged enclosure able to withstand an internal explosion but not allow explosively hot gases to escape, and 2. maximum surface temperature, with equipment operating inside, that will not ignite the surrounding atmosphere. Also, testing insures that any material in contact with the container surface will not be ignited by a hot spot. Associated with the first practice, the enclosures are inspected for: 1. a safe flange gap width, 2. a pressure increase during ignition, and 3. an hydrostatic pressure withstand level. The hydrostatic pressure level is almost always determined by a meas¬ured ignition-pressure test and is usually applied to prove the mechan¬ical design to some safety factor. Consequently, explosion-proof enclosure testing includes temper¬ature, permissible flame gap, and pressure. Specifications and prev¬ious research also can be similarly separated even though some interre¬lation exists between the flame gap size and internal enclosure pressure during an explosion. The Schedule 2G Sections applicable to these subjects are: 1. 18.2 Definitions; 2. 18.6 Applications;

Jan 1, 1974

By Thomas M. Barczak

Longwall operators are again pushing the envelope in terms of life expectancy for longwall shields. State-of-the-art shields are now expected to last more than 60,000 loading cycles, twice the life expectancy compared with those of a decade ago. A review of trends in shield design shows that shields continue to increase in both size and capacity. Some state-of-the-art shields now weigh over 30 tons and provide up to 1,200 tons of support capacity. Although life expectancy has increased and modern shields are structurally more reliable, premature failures do still occur. This paper provides an engineering and operational assessment of shield design and provides key points to observe in what causes premature shield failures. Design practices to improve structural margins of safety that will prevent premature failures from occurring are also examined. A survey of recent shield failures is provided, as well as trends in shield design and how they might impact the performance and longevity of a shield. Hydraulic failures are more common than structural failures. Although hydraulic failures occur on all aging longwall shields, they often go undetected for long periods, resulting in degraded support capacity that can lead to serious ground control problems. The fundamentals of shield hydraulics are described in order to evaluate hydraulic failures that plague all shields at some point in their service life, and practical methods to detect hydraulic failures are examined. The paper concludes with recommendations for inspecting damaged shields and safety precautions regarding their continued use.

Jan 10, 2000

By Bill M. Stewart, Phil W. Patton, Curtis C. Clark

Back injuries from handling materials in underground mines continue to be a major safety problem. In spite of the ingenuity of many people and the development of numerous mechanized aids, the number of materials-handling injuries remains second only to the number of roof fall injuries in underground coalmines. Relocation and repositioning of electrical cable, conveyor belt parts, and roof bolt sup-plies in particular are the sources of significant numbers of back injuries. To help reduce such injuries, researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are examining Mine Safety and Health Administration accident data to determine correlations between materials-handling tasks and the number of back injuries. Also being investigated are new technologies used in underground mines in the United States. Equipment is being developed or modified that would replace the necessity of doing lifting tasks manually. A Coleman manipulator was tested, and modifications were made to make it more suitable for underground mine use. To reduce or eliminate the need to manually clean off materials that commonly plug grizzly openings, a track-guided pincher arm device was developed. Oversized rock can be broken with the pincher arms in the up position, and the arms can be lowered to grab and remove debris. The arm can also be used in a sweeping action to remove cohesive fines that may bridge grizzly openings.

By John H. Hild

The topography of the Jamestown fluorspar area is rough and ranges from 6,400 to 8,000 feet in altitude. Some fluorspar was mined as early as 1870, but mining really did not begin in earnest until 1940, and up to July 1947 it is estimated that 272,500 tons of fluorite was mined and milled. In 1947 the General Chemical Co. was mining fluorite and milling it in a 200-ton-a-day mill at Valmont, 7 miles east of Boulder, and the Ozark-Mahoning Co. was milling ore in a 100-ton-a-day mill at Jamestown, using ore mined, by H. M. Williamson & Son. These fluorite deposits comprise veins in a granite country rock. The Bureau of Mines drilled eight holes, aggregating 2,579.1 feet, on the Blue Jay vein; four holes, aggregating 1,434 feet, on the Chancellor; and one 350-foot hole on the Nations Treasure. Fluorite of a minable grade and width was found in 10 of the holes drilled. In this report the location and accessibility, physical, features and climate are described and a brief history of the district is given. The deposits and character of the ore and sampling and analyses are described, mine workings are outlined, and work performed by the Bureau of Mines is summarized. Diamond drill logs are shown in appendix I, and 'Sample analyses are tabulated in appendix II.

Jan 1, 1949

By Joseph A. Perry

One goal of the Bureau of Mines is to develop technology tp insure a dependable supply of minerals to the United States. To support this goal, the Bureau's Albany Research Center has modified a commercial atomic absorption spectrophotometer to rapidly determine trace levels of mercury by cold-vapor atomic absorption spectrophotometry. Such diverse materials as ores, mill products, stream water, sediments, and flue dust have been analyzed. A very high dynamic range of 0.2 ng/ml to 1 µg/ml of mercury in solutions is routinely analyzed by this instrument.

Jan 1, 1981