Search Documents

By K. E. Hjelmstad

During an underground mine fire, air can be rapidly depleted of oxygen and contaminated with smoke and toxic fire gases. Any delay in warning miners could have disastrous consequences. Unfortunately, present mine fire alarm systems, such as stench, audible or visual alarms, telephones, and messengers, are often slow, unreliable, and limited in mine area coverage. Recent research by the U.S. Bureau of Mines has demonstrated that ultra low frequency electromagnetic signaling can be used for an underground mine fire alarm. In field tests of prototype equipment at five mines, electromagnetic signals from 630 to 2,000 Hz were transmitted through mine rock for distances as great as 1,645 m to an intrinsically safe receiver. The prototype system uses off-the-shelf components and state-of-the-art technology to insure high reliability and low cost. When utilized, this. technology would enable simultaneous and instantaneous warning of all underground personnel, regardless of their location or work activity, thereby increasing the likelihood of their successfully escaping a mine disaster. This report presents the theoretical basis for through-the-rock ultra low frequency electromagnetic transmission, design of the prototype transmitter and receiver, and the results of in-mine tests of the prototype system.

Jan 1, 2010

By W. T. Abel

Laboratory tests were conducted with a closed, recycling system to evaluate the effectiveness of solid-in-gas suspensions as heat transport mediums. Micronized graphite in helium or nitrogen was circulated by a centrifugal compressor to determine the feasibility of the method and heat transfer capabilities of the mediums. Suspensions were circulated without plugging or eroding the compressor or piping. At low flowrates and light (0.1 to 0.2 volume-percent) graphite loadings, slightly less power was required to transport a given amount of heat with suspensions than with helium alone. Graphite deposition on the heat exchange surfaces of the cooler decreased the heat transfer effectiveness at higher solids concentration. Efforts to eliminate deposition are described.

Jan 1, 1963

In this U.S. Bureau of Mines report, in situ vat leach mineral recovery system concepts are described and cost compared with conventional mining and pad and autoclave leach processing systems. In the proposed systems, leachable ores are enclosed in place in reagent-impermeable in situ vat constructions. The ores are then rubbled and flood leached or flood oxidized and leached. The in situ vats are called stope leach or stope autoclave vessels. The report also proposes ore body-adjacent in situ vat constructions containing rechargeable processing stopes. A series of ore body-specific, innovative, and conventional mineral recovery systems case study designs are described and prefeasibility level costed. Based on a comparison of these prefeasibility level cost estimates, the proposed systems are determined to be economically competitive with conventional min¬eral recovery systems. The in situ vat leach mineral recovery systems concepts for leachable and refractory ores are developed around the drill-split narrow-vein and longwall mining methods described in part 1 of this Information Circular series.

Jan 1, 1995

By H. E. Powell

The magnetic susceptibilities of 34 manganese-bearing minerals were determined. The source of each sample and petrographic, spectrographic, and chemical analyses are given. Included are values for ismorphous series showing wide ranges of composition and for a few high-purity synthetic minerals.

Jan 1, 1968

By T. F. Tomb

Past experience has shown that the penetration characteristics of the 10-mm nylon cyclone used on approved personal sampling equipment are significantly different from those determined in the laboratory using a nonpulsating flow source. The Bureau of Mines has developed and recommended a modification to presently approved equipment that will alleviate this difference. However, as a result of this modification, a new relationship for converting respirable dust concentrations measured with approved personal sampling equipment to equivalent concentrations as measured with an MRE instrument will have to be established. This Bureau of Mines report describes the underground sampling program conducted to establish a new factor for converting respirable dust concentrations measured with personal sampling equipment, modified with a recommended pulsation damping device, to an equivalent concentration as measured with an MRE gravimetric dust sampler.

Jan 1, 1973

By Frank C. Andreuzzi

The Federal Bureau of Mines conducted a demonstration project to reclaim 125 acres of abandoned strip-mined land in Lackawanna County, Pa., for public recreational, historical, and educational use as a park. The Bureau was involved in the development of the general site plan, and engineered and supervised the basic land rehabilitation. The park's Facilities include outdoor recreational activities, picnic grounds, children's play areas, primitive overnight camping, and winter sports. A major attraction is the Anthracite Museum constructed by the Pennsylvania Historical and Museum Commission The project may serve as a prototype for reclaiming existing and future surface-mined lands.

Jan 1, 1976

By David Schlain

This Bureau of Mines report describes a method for electrodepositing titanium diboride from a molten salt bath. Initially, the electrolyte is a mixture of LiBO2, NaB02, Na2 Ti03 , Li2Ti03, and Ti02? The cell is operated at 900° C in a dry, inert atmosphere with consumable anodes of titanium or hot-pressed titanium diboride (TiB2) powder. Agitation of the electrolyte is essential. Current densities may be 6 to 9 amperes per square decimeter (amp/dm2) with titanium anodes and 9 to 30 amp/dm2 with titanium diboride anodes. A current density of 6 amp/dm2 is equivalent to a plating rate of about 35 micrometers per hour. The adherence of the TiB2 deposit varies with the substrate material. It is most adherent on molybdenum and on 4130 steel that has been preplated with copper and nickel, less adherent on nickel, and still less adherent on Inconel and on 4130 steel without the preplate. Cathode and anode reactions are suggested.

Jan 1, 1976

By Jeffrey Shawn Peterson

The testing procedures of the U.S. Mine Safety and Health Administration specify that intrinsic safety acceptance tests be conducted using a standard tungsten-cadmium electrode configuration in the break- flash apparatus. However, in realistic mining environments, other materials may be more likely sources of sparking. Information defining the probability of spark ignition between common materials such as aluminum, brass, copper, lead, tin, cold-rolled steel, and stainless steel is of more practical value in determining ignition hazards. The U.S. Bureau of Mines has completed an investigation of the influence of material on the ignition probability using the breakflash apparatus. By comparing ignition currents or ignition voltages corresponding to a probability of one ignition per thousand sparks to those found previously for cadmium, a margin of safety may be estimated for each material. This report presents the results of an investigation into the influence of disk electrode material on the probability of ignition.

Jan 1, 1992

By J. M. Gomes

The Bureau of Mines investigated electrolytic techniques for preparing diborides of the group IV B metals. TiB2, ZrB2, and HfB2 were electro-deposited from their respective oxides dissolved in borate-chloride-cryolite electrolytes. Titanium diboride was also electrodeposited from rutile (Ti02) dissolved in a Na2,B4O7-Na2C03-Na3A1F6-NaC1 electrolyte at 1,050° C; 14 kW-hr were required to produce 1 pound of TiB2. Major impurities in the TiB2 produced in a 10-deposition cycle experiment, in weight-percent, were Al, 0.2; Cr, 0.3; Fe, 0.1; V, 0.3; C, 1.4; and 0, 1.0. Zirconium diboride was electro-deposited from zircon (ZrSiO4) dissolved in a Na2B407-NaOH-Na3A1F6-NaCl-NaF electrolyte at 1,050° C. The ZrB2 produced in a 10-deposition cycle experiment contained the following impurities in weight-percent; Fe, 0.1; Si, 0.5; C, 0.3; and 0, 0.6. Energy required to produce 1 pound of ZrB2 was 9.3 kW-hr.

Jan 1, 1975

By Joseph W. Town

The Bureau of Mines conducted studies related to SO2 air pollution to determine attritioning rates, SO2 sorption rates, and sulfur loads that could be obtained on commercial alkalized alumina sorbent pellets. Fluidized-bed attritioning rates ranged from 0.025 pct/hr for alkalized alumina with a crushing strength of 4 kg to 0.075 pct/hr for 0.5 kg crushing strength mate¬rial. Airlift attritioning rates ranged from 0.50 pct/hr for 3 kg crushing strength alkalized alumina to about 3 pct/hr for 0.5 kg material. Attritioning rates for the commercial alkalized alumina were comparable to those obtained for sorbent pellets prepared in the Bureau of Mines laboratory. Sorption rates were related to S02 concentration in flue gas, temperature, and presence of nitrogen oxides in the gas stream. Sorption rates at 300° C were 0.35 X 10-6 gS/gp/sec (grams sulfur per gram pellet per second) in 0.045 pct so, gas, 5.1 x 10-5 gS/gp/sec in 0.34 pct SO2 gas, and 65 X 10-5 gS/gp/sec in 10 pct SO2 gas. For the 0.34 pct S02 gas, sulfur loads of 0.10 gS/gp (the projected load for regeneration) were obtained in 47 min at 130° C and in 116 min at 300° C. The presence of either NO or NO2 in the 0.34 pet S02 gas increased the SO2 sorption rates 2 to 3 times at 300° C, but had no effect at 130° C.

Jan 1, 1969

By Earl L. Phillips

The Bureau of Mines conducted laboratory tests on samples of pozzolaniccement concrete to develop a low- strength backfill . Results show that support costs can be lowered by replacing a portion of the portland cement in mine backfill with pozzolan ( fly ash ) and lime . Unconfined compression tests on various ratios of fly ash to cement in 84 samples produced compressivestrength curves that can be used to estimate the best backfill mix for any mine .

Jan 1, 1964

By Anthony T. Iannacchione

The Bureau of Mines developed data on the methane content of the Hartshorne coalbed, Haskell and Le Flore Counties, Okla. The methane content is calculated to be between 1.1 and 1.5 trillion cubic feet, based on an estimate of total coal in place of 2.4 to 3.2 billion short tons. Methane increases with depth, but the rate of increase decreases with greater depths. Degasification in advance of mining is recommended for all mines operating at depths greater than 500 feet to reduce hazards and methane explosions, decrease mine ventilation costs, and conserve the natural gas that would be otherwise wasted.

Jan 1, 1979

To minimize the equipment operator?s respirable dust exposure in enclosed cabs of mobile equipment by install-ing cab filtration and pressurization systems and by keep-ing doors and windows closed. Background Enclosed cabs are used on mobile equipment to protect operators from health and safety hazards. The primary health concern is overexposure to respirable dust. Examples of such equipment in mining include drills, dozers, haul trucks, and other equipment. When equipment is new, the operator?s dust exposure is normally at acceptable levels. As the equipment ages and gaskets and seals deteriorate, the air quality inside an enclosed cab can reach a point where it is no longer at acceptable levels for the equipment operators. In an effort to improve the air quality in enclosed cabs of older mining equipment, NIOSH has been performing research to retrofit cabs with new filtration and pressurization systems. Over the past few years, this research has shown that retrofit systems can substantially improve the cab?s air quality back to safe and acceptable levels. How-ever, this is only possible when a positive cab pressure is achieved and maintained. Thus, when a cab door or window is opened, the cab pressure drops to zero and the cab filtration and pressurization system is rendered ineffective. During a recent field study, the magnitude of this impact was noted when a drill operator repeatedly opened the cab door throughout the course of the drill cycle. Upon closer examination, it was determined that the cab door was being opened to manually guide the next drill steel into place each time an additional section of steel was needed to drill deeper holes.

Sep 1, 2008

By A. E. Isaacson

The U.S. Bureau of Mines determined the effect of common sulfide minerals on the corrosion rates of various types of ferrous alloy grinding media. Data obtained from this study will aid in determining the contribution of any electrochemical reactions between sulfide minerals and grinding media to the total grinding media consumption. Common sulfide minerals used in this study were chalcopyrite, galena, and sphalerite. In the presence of oxygen, chalcopyrite was found to increase the corrosion rate, galena was found to decrease the corrosion rate, and the effect of sphalerite was dependent upon the type of grinding media. Possible electrochemical reactions of these minerals in the presence of grinding media are suggested.

Jan 1, 1989

By James P. Bennett

To identify construction materials for emerging technology in chemical and metallurgical processes, the Bureau of Mines investigated the acid resistance of ceramic materials. Eight commercial ceramic materials comprising two red shale, two fire clay, a silica, a five-claybonded silicon carbide, a carbon, and a high-alumina brick were evaluated. Samples were exposed for 110 days to 20 wt pct HCl at 50°, 70°, and 90° C and to 30 wt pct HCl at 70° C. Statistically significant changes in cold crushing strength, volume, and weight were generally small or not detected. The leach rates of Al, Ca, Fe, K, Mg, Na, Si, and Ti ions were monitored. The carbon brick sample had the best acid resistant properties with a maximum total leached ion weight loss of 0.004 wt pct. The silicon carbide, the silica, and one of the fire clay bricks also had excellent acid-resistant properties.

Jan 1, 1983

By E. Chin

The production of crude mineral commodities in Bangladesh was limited to natural gas, a small amount of construction materials, and clay for ceramics and bricks. No metallic minerals were mined. The only mineral commodity of economic significance was natural gas. Natural gas production has 'been climbing steadily and becoming an increasingly important source of energy for the country. Proved gas reserves were over 4.5 trillion cubic feet, but the amount has been increasing as exploration discovers large new deposits. Some sources quote reserves at over 10 trillion cubic feet.

Jan 1, 1984

By Thomas C. Denton

The Old Reliable copper mine was first examined by Harlow D. Phelps , an engineer of the Bureau of Mines , in October and November 1942 , in compliance with a request from the War Production Board , which furnished copies of assay maps of the 100- and 200-foot levels and requested that they be check-sampled . The author and R. li. Grantham and W. D. Hughes , engineers of the Bureau , made a second and more detailed examination later , after a number of manways had been opened that were inaccessible when the first examination was made .

Feb 1, 1947

By Mark I. Copeland

Bureau of Mines researchers investigated the combined effect of copper and tin additions on the mechanical properties of hot-rolled steels. Wrought steels containing 0.2 wt-pct C and up to 0.2 and 1.0 wt-pct Sn and Cu, respectively, were made and evaluated by conducting tensile and impact tests and electron-beam microprobe and electron microscopy examination. Tin additions did not significantly affect the tensile properties of steel at different copper contents in the hot-rolled condition. Tin lowered the copper content at which strengthening by copper precipitation normally starts, 0.8 wt-pct, and decreased the strength of steel aged at 1,022° F (550° C). The most adverse effect of tin was lowering the notch toughness of steels at most copper contents.

Jan 1, 1976

By Will H. Coghill, I. L. Feld, G. D. Coe

"INTRODUCTION During the course of research on the beneficiation of the Big Seam iron ores of Birmingham, Ala., an urgent need was felt for quick iron assays of grab samples for mill control. Since the gangue minerals in these ores - quartz, limestone, and clay - all have about the same specific gravity, the use of a specific-gravity method was anticipated as a means of measuring the iron content. The idea of estimating the composition of a mineral mixture by measuring its specific gravity is by no means new. However, the usual method of carry in out this idea proved unreliable when applied to the Big Seam ores. The usual rapid method of determining specific gravity consists of measuring the volume of a known weight of sample that has been dried at high temperature. The inadequacy of this method led to the development of the rapid, modified, specific-gravity determination described in this paper.This work- was an incidental development resulting from research on beneficiation of iron ores by the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama and ore producing companies of the Birmingham district."

Jan 1, 1946

By C. R. Stephan, N. B. Greninger, J. R. Lipscomb

The U.S. Bureau of Mines and the U.S. Mine Safety and Health Administration (MSHA) are participating jointly in a research program to evaluate the strength characteristics and air-leakage resistance of various proposed seal designs for use in underground coal mines. The full-scale seals were constructed in the USBM's experimental mine at the Lake Lynn Laboratory, air-leakage tested, then subjected to pressure pulses of 20 psig or greater. bjected to pressure pulses of 20 psig or greater. In experiments prior to this study, seven seal designs using solid-concrete blocks were tested. Only the standard-type seal passed the explosion and air-leakage criteria. Tests also were performed on four seals constructed with low-density foam blocks. All four of these seal designs withstood the pressure pulse. In more recent studies, nine cementitious foam seal designs of varying thicknesses and densities were investigated. Six of the nine designs successfully survived the explosion overpressures. Six wood- block convergence seals also have been tested. The typical 3-ft-thick, wood-block seal design currently used in many coal mines did not maintain its integrity, in the absence of convergence forces, following the explosion test. Five modified wood-block seals successfully withstood the 20-psig pressure pulse. Based on these tests, three alternative seal construction materials, cementitious foam, low-density foam block, and wood, have been approved by MSHA for use in underground coal mines.

Jan 1, 1993