Search Documents

By W. L. Anderson

Standard tellurium analytical procedures were modified to obtain the greater sensitivity needed to support a survey of tellurium resources by the Bureau of Mines. Resulting volumetric and spectrophotometric methods for determining tellurium in all types of tellurium-containing materials are described. Sample decomposition and preliminary separations of interfering selenium, gold, and silver are the same in both procedures. The volumetric method is applicable to samples containing a minimum of 10 parts per million of tellurium, In this method the tellurium is reduced to elemental form, and the colloidal suspension is titrated with 0.01 normal iodine solution. The weight of sample for analysis, from 0.25 to 10 grams, should be selected so that the sample contains 0.1 to 5 milligrams of tellurium. To insure accuracy, duplicate samples should be run and the results averaged, particularly on samples of low tellurium content: The limit of determination is 0,001 percent tellurium, which is equivalent to 0.1 milligram of tellurium when using a 10-gram sample. The spectrophotometric method is particularly applicable to low-tenor materials containing from 0.5 to 50 parts per million of tellurium. Up to 10 gram samples are required for making accurate determinations in the low-concentration range. The sample used should contain between 5 and 100 micrograms of tellurium. The turbidity of a colloidal suspension of tellurium prepared from such a sample is determined in a spectrophotometer .t at a. wave-length of 440 millimicrons, and this value is compared with those of standard samples containing known amounts of tellurium.

Jan 1, 1963

By B. R. Mohal, S. Chander

"The adsorption and wetting behavior of freshly ground and aged coals has been determined in the presence of a nonionic surfactant. The amount of surfactant adsorption changes with the concentration and ""age"" of the coal. The freshly ground coal has smaller amounts of adsorption at lower surfactant concentrations than the ""aged"" coal whereas at large surfactant concentrations, the order is reversed . In the latter case, more surfactant is adsorbed on fresh coal than on the ""aged"" coal . . It is proposed that at low concentrations, the surfactant adsorbs through both hydrophobic and hydrophilic interactions with the molecule lying parallel to the· surface, whereas at higher concentrations surface micelles form at the hydrophobic sites. The wetting behavior correlates well with the adsorption behavior.INTRODUCTIONNonionic surfactants have many applications in the coal and mineral processing industry. They can be used as dispersing agents to modulate flotation, flocculation and filtration of particulates (1). They can also be used to increase the wettability of hydrophobic solids such as coal and can hence be used as dust suppressants (2,3). Although the adsorption of representative nonionic surfactants such as Triton N-101 (an ethoxylated nonylphenol with 9.5 moles of ~thylene oxide and HLB equal to 13.4) have been studied extensively on substrates such as calcium carbonate (4), silica (5) carbon black (6) and graphite (7), very few studies are available for coals. Coals differ from other substrates with respect to two important characteristics: 1) coal are porous and 2) coals consist of a patchwork of hydrophobic and hydrophilic sites (8). Since the adsorption characteristics of a surfactant are influenced significantly by the nature of the substrate the characteristics of the coals must be taken into consideration."

Jan 1, 1989

By Nicholas Kyriazi, John P. Shubilla

A joint effort by the U.S. Bureau of Mines (USBM) and the US. Mine Safety and Health Administration (MSHA) was undertaken to determine how well self-contained self-rescuers (SCSR's), deployed in accordance with Federal regulations (30 CFR 75.1714), held up in the underground environment with regard to both physical damage and aging. This report presents findings regarding laboratory-tested SCSR's in the fourth phase of testing from 1989 to 1993. The SCSRYs were tested on human subjects and on a breathing and metabolic simulator (BMS). These results indicate that most of the apparatus, if they pass their inspection criteria, perform as expected except units with manufacturing defects. However, when the apparatus are carried in and out of the mine daily and stored at the working section, they may suffer abuse. Physical signs of abuse, unless extremely obvious, are frequently not detected by the miners or mine operators. In addition, some apparatus collected for this study had not been returned to the manufacturer in a recall effort for correction of a manufacturing defect. In both cases, the apparatus would have presented problems in emergency use. Recommendations include improved training in inspection procedures and better enforcement of recall notices.

Jan 1, 1994

By R. D. Dey, V. Castranova, J. M. Antonini, J. A. Blackford Jr.

Alveolar macrophages (AM) exposed to cytokines or bacterial lipopolysaccharide (LPS) produce the free radical nitric oxide (NO·) by an inducible nitric oxide synthase (iNOS). They also release reactive oxygen free radicals following exposure to silica dust. The purpose of the present study was to determine whether NO· is produced by rat AM and/or recruited leukocytes following the intratracheal (IT) instillation of silica. Male Sprague-Dawley rats (175 to 225 g) were IT instilled with either silica dust (10 mg/100 g body wt) or LPS (0.25 mg/100 g body wt). After 24 h, bronchoalveolar lavage cells (BALC) and lavaged lung tissue were assayed for iNOS mRNA. Cell counts of BALC and iNOS-dependent (Nw-nitro-Larginine methyl ester [L-NAME]-inhibitable) chemiluminescence generated by AM were also determined. Northern blot analysis demonstrated that the steady-state levels of BALC iNOS mRNA were significantly increased by 3-fold following IT silica and by 7-fold following IT LPS. Partially enriched fractions of either AM or leukocytes from silica-treated rats both exhibited significantly elevated iNOS mRNA in Northern analysis. iNOS-dependent chemiluminescence was significantly increased in AM by 36-fold following IT silica and by 89-fold following IT LPS. Differential counts of BALC showed that AM numbers did not change in any of the treatments; however, red blood cells increased by 30-fold following IT silica and by 23-fold following IT LPS. Total leukocytes (polymorphonuclear leukocytes plus lymphocytes) increased by 58-fold following IT silica and by 274-fold following IT LPS. The results demonstrate that AM and neutrophils iNOS steady-state mRNA levels, AM iNOS-dependent chemiluminescence, and lavagable red blood cells and leukocytes all increased following IT silica. These findings suggest that NO· production in rat AM and neutrophils is increased in response to silica. NO· has the ability to then combine with superoxide and form a highly reactive toxic species, peroxynitrite, which may be responsible in part for silica-induced lung damage.

Dec 1, 1995

Any communication system requires at least three elements in order to function: a transmitting device, a receiving device, and a transmission line or propagation medium. Even the device children use, tin cans connected with string, consists or these three elements. One speaks into one can (transmitter), which vibrates at the same frequencies as the voice. The string (transmission path) picks up the vibrations of the can and carries them along its entire length. The other can (receiver) detects the vibration and reproduces the original sounds to a lesser extent depending on distance, tightness of string, type of string, etc. All communication systems depend on these three elements: transmitter, transmission path, and receiver. Communication systems can be divided into three fundamental categories: wired phone systems, radio systems, and carrier current systems. Sections 2.2, 2.3, and 2.4, respectively, describe these systems and explain the basic principles of how each works. Hybrid systems are those systems that use various combinations of the three basic communication methods. Hybrid systems are described in section 2.5. There are some other methods of signaling (stench warning, bell signaling, etc.) that can be used in underground mines to transmit or convey information. These systems, although they cannot be considered true communication systems since they do not provide voice or even two-way communication, are briefly described in section 2.6. 2.2 Wired Phone Systems Wired phone systems are all those that depend on a wire connection between phones with the wire carrying the voice signals. Figure 2-1 is a diagram of two typical wired phone systems.The top panel shows a simple single pair party line system. In this system each phone is connected to a common pair of wires, and a person speaking into one phone will be heard at all the other phones on the line. The bottom panel shows a multipair private line phone system. In this type of system, each phone is connected by its own individual pair of wires to a central switch or telephone exchange. To establish a call between two phones in this system, the lines between the two phones must be connected (switched together) within the telephone exchange. In early exchanges, the connections were made manually by an operator. These exchanges are called Private Branch Exchanges (PBX's). Today, equipment within the exchange can automatically connect each phone to any other phone in the system. These exchanges are called Private Automatic Branch Exchanges (PABX's). There are many different types of automatic exchanges. Some utilize switches to physically make each connection according to the number dialed. Other, more advanced exchanges are completely solid state and may even be computer controlled. [ ]

Jan 1, 1984

By Charles A. R. Lambly

This paper, which describes the mining practices of the Pend Oreille Mines & Metals Co. at Metaline Falls, Wash., is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in various mining districts of the United States. ACKNOWLEDGMENTS Acknowledgment is made to L. P. Larson, president, and Jens Jensen, secretary, of the Pend Oreille Mines & Metals Co. for permission to publish this paper. information was supplied by E. Berglund, mine superintendent; Earl Miller, chief engineer; Lynn Kinney, John Currie, and Wally Frick, engineers; Arthur Newman, chief clerk; and Jack Crampton, assayer.

Jan 1, 1941

By Grace N. Broderick

U.S. supply and demand data for coal, by States and regions, were tabulated for the years 1960 and 1965. Estimates are provided of State-by-State quantitative data for the coal industry that can be integrated into State and regional energy balances by source, form, and consumer sectors, and used for estimates of interstate and interregional energy flows. The tables give an estimated total supply of coal available for consumption, and also report the distribution of the supply among the major consuming sectors (household and, commercial, industrial, transportation, and electricity generation). To enable comparison of coal data with those for other energy forms, tonnages were converted to British thermal units (Btu). Future energy analysis studies could be facilitated by changes in the categorization of information collected on the coal industry. The data shown are based primarily on Bureau of Mines source material.

Jan 1, 1969

By R. R. Wells

As a part of the strategic mineral program, examining engineers of the Bureau of Mines collected samples several manganese properties in Colorado. As all of the ores were too low-grade to be acceptable to manufacturers of ferromanganese, beneficiation studies were required .to determine the amenability of the ores to concentration. Manganese in the form of impregnations in sedimentary beds is found in the Denver plains area a few miles east of the Rocky Mountain front. Deposits are reported to occur intermittently over a distance of more than 200 miles. The manganese oxides occur in beds of conglomerate or arkosic sand, generally accompanied by limonite. The Manganese and iron oxides,, however, usually are found in separate layers. Three samples were submitted for beneficiation tests, two samples from Buckley Field bombing Yang, Arapahoe County, and one from near Franktown, Douglas County.

Jan 1, 1952

By T. T. Campbell

Although secondary recovery of lead and lead-tin alloys has been common practice in the United States during recent years, there is little published in-formation concerning recovery techniques. Available information does not cover metal recovery from wet dross skimmings. This investigation by the Bureau of Mines was undertaken to develop techniques that would allow lead-tin alloys to be recovered from wet dross skimmings containing large amounts of zinc chloride. A process was developed, on a laboratory scale, for recovering lead-tin alloys from wet solder dross skimmings. Straight water leaching, either with or without a second leaching operation carried out with a Na2C03 addition for removing chloride, produced a dross that could be smelted without further treatment. Overall recoveries averaging 92 percent of the metal values in the dross were obtained in the form of lead-tin alloys, which had an average tin content of 16 percent and lead content of 84 percent. The recovered alloy contained less than 0.02 percent zinc, as determined by both chemical and spectrographic analyses.

Jan 1, 1956

By Jerry G. Craig

The Bureau of Mines has developed a computerized oil and gas well data retrieval system from studies of the waterflood potential of a producing reservoir. This system stores pertinent information about each well completed in a reservoir and facilitates selection and manipulation of large volumes of data. Use of the system enables reservoir information to be supplied rapidly, accurately, and at less expense.

Jan 1, 1971

By Daryl R. Tweeton

The Bureau of Mines compared the effects of surface-active chemicals with those of pure water on core-drilling rock and quartz and on fracturing quartz. The objectives were to determine if these chemicals assist drilling and fracturing rock and if zeta potential control was worth pursuing as an aid to full-scale drilling. All tests were performed in the laboratory. No significant increases in drilling rates were observed for 1 to 10,000 ppm Al (as AlC13) in flushing water when drilling microcline or serpentine, nor for 1 to 10,000 ppm Mg (as MgC12) when drilling microcline or marble. Concentrations near those giving a zero zeta potential were used with microcline and marble. A 50-pct rate increase was observed for drilling quartz in 0.7 ppm oleylammonium acetate, which gave a zero zeta potential. No other concentrations were used. No effect on the tensile strength of quartz thread in 0.05 ppm Al (as AlC13), which gave a zero zeta potential, was observed. Heptanol, reported to give a zero zeta potential on quartz, did not reduce the bending strength of small quartz bars below that in water. These generally negative findings raise doubt about the usefulness of zeta potential control in full-scale drilling. The results, combined with previous studies, suggest that controlling physical properties of drilling fluids, such as viscosity, is more useful than altering chemical properties.

Jan 1, 1976

By R. V. Ramani

"In a 1985 seminar, we were told that over-optimism abounds in Artificial Intelligence (AI), that AI is neither a science nor a technology yet, and that we will be both exhilarated and disappointed with AI. In fact, even today, there is no single accepted definition of AI; however, certain features have been identified by AI researchers as essential to consider an entity (e.g. machine or program) to be intelligent. According .to Shank (1987), these features include communication (to be able to communicate with), internal knowledge (knowledge about itself), world knowledge (awareness and knowledge about the world outside), intentionality (knowing what one wants and a plan to seek it, ie. goal seeking behavior), and creativity (being adaptable to changing conditions). None of these figures would individually define intelligence; however, each would be a part of intelligence in its own way.The prospects for the development of entities with AI have never been as good as they are now. The combination of advancements in computer hardware and .software along with new insights into the ways in· which we store knowledge and use it for problem solving has enhanced the potential for the creation ~f intelligent entities. After some unbounded optimism of a major breakthrough in the fifties and frustrating disappointments in the two following decades, it appears now that AI has emerged from research labs to industrial practice. This is confirmed by the growing number of repeat applications of AI in business and industry to the extent that AI can now be considered a technology.AI applications are categorized into several distinct areas such as Natural Language Processing, Speech Recognition and Synthesis, Expert Systems, Robotics, Machine Vision, etc. Of these practical realizations, Expert Systems (ES) has the greatest potential for meeting the decision-making needs of the manager in the ever-growing complex scoio-technical systems. Prof. Feigenbaum, an expert and leader on expert systems, has defined Expert System as"" ... an intelligent computer program that uses knowledge and inference procedures to solve problems that are difficult enough to require significant human expertise for their solution. Knowledge necessary to perform at such a level, plus the inference procedures used, can be thought of as a model of the expertise of the best practitioners of the field."""

Jan 1, 1989

By Arnold O. Tanner

The domestic mining industry continued to be strengthened and revitalized in 1989. The healthy conditions and the industry comeback that began in 1987 continued to spread and became more established for many commodities. Relatively comfortable and stable commodity prices, still found predominantly in the metals sector, reinforced other operational factors in bringing vitality to the mining and mineral processing industries. New streamlined business practices, mine and plant modernizations, and the progressive use of new technologies successfully helped lower operating costs and increase efficiency during the past 5 to 7 years. An element common to these three factors of industry renewal and growth was the ever-increasing infusion of and growing dependence on constantly advancing computer technology applications. This trend of increasing computerization was occurring throughout the mining and mineral processing business while it similarly was in most facets of modern business and culture. Some commodities and companies still struggled to outlive sluggish prices and other unstable market conditions or to modernize their businesses, but increases in productivity and profits were more common. A trend toward increased mechanical excavation in nonsoil materials was beginning to surface as a substitute for standard cyclic mine development techniques, such as drill-and-blast and surface shovel-and-truck routines. More continuous mechanical excavation offered the potential for increased production, fewer people at the working face, better ground control, and generally improved safety. The main limitation was rock hardness. The construction industry had already recognized the benefits of tunnel-boring machines for long underground drives and mechanical planers for pavement removal. The Colorado School of Mines held a short course during the year entitled, "Mechanical Excavation Techniques in Mine Development and Production,'" which was at-tended by nearly 100 engineers from 12 countries. The consensus of attendees was that for the most efficient use of these machines and techniques, new mining plans needed to be developed beyond the simple adaptation of those excavators to existing mine plans.1

Jan 1, 1991

By G. W. Jones

As a part of it investigations pertaining to the promotion of safety, the Bureau of Mines is investigating various means, useful for the elimination or mitigation of the explosion hazards of combustible gases encountered in mining and industry. Information has been obtained and a procedure developed whereby the explocibility of many complex, gaseous, combustible atmospheres may be calculated in a simple manner without the necessity of performing laborious laboratory experiments. In a previous publication4/ data were given and a method described whereby the limits of inflammability of gaseous mixtures, including methane, hydrogen, carbon monoxide, nitrogen, carbon dioxide, and oxygen, could be determined by calculation. The information published in that report enables one to calculate the limits of inflammability of such gases as are liberated by mine fires, gases from explosives, automobile exhaust ran, uses present after mine explosions, blast-furnace gas, and other gases containing part of or all of the above-listed constituents.

Jan 1, 1938

By C. J. Thompson

This Bureau of Mines study describes the preparation of sulfur compound concentrates boiling from 225° to 400° C, and reports the sulfur types detected in these concentrates by low-voltage mass spectrometry (LVMS). Existing LVMS methods were extended; the procedures described should be generally applicable to high-boiling petroleum distillates and concentrates as a preliminary means of narrowing the number of factions to be considered for more detailed separation and identification studies. The following major sulfur compound constituents of petroleum are indicated by the data: benzothiophenes, dibenzothiophenes, naphthanothiophenes, naphthenobenzothiophenes, and homologs and isomers of these. Cyclic and chain sulfides comprise a significant portion of the gas-oil range sulfur compound types. The presence of some classes of sulfur compounds containing two sulfur atoms per molecule was indicated.

Jan 1, 1966

By H. M. Cooper

The determination of moisture in coal is an empirical test, because the time, temperature, and equipment are specified. The essential features of the equipment and details of the procedure are given in A.S.T.M. Designation: D271-44.:2. According to the specifications, the following features should be incorporated in the equipment used: 1. Oven must have uniform temperature in all parts. 2. Oven must be constructed with minimum of air space. 3. Oven must have means of changing the air two to four times per minute. 4. Air must be dried over sulfuric acid (sp. f-7. 1.84). The analytical procedures governing most of the nation's coal purchases are those given in A.S.T.M. Standards referred to above. These standards are general arid of such scope as to cover all ranks and types of coal. In cases where only the moisture is required, a faster method than the standard procedure is desired.

Jan 1, 1948

By Danqing Xu, A. W. Khair

"This paper presents a laboratory simulation of regrinding and resulting dust generation. An Automated Rotary Coal Cutting Simulator (ARCCS) was modified to conduct regrinding experiment. In order to estimate the effects of coal properties and operating parameters on regrinding and dust generation, an orthogonal fractional factorial experimental design was implemented in regrinding experiment. Marple personal cascade impactors, Series 290, were used to measure dust concentration during experiment. Three types of coal seams, namely, Waynesburg, Pittsburgh, and Lower Kittanning, were used to represent different coal properties. Experimental results and complete parametric analysis were presented.In a rotary cutting system, all the broken coal and part of the remaining coal from previous cutting cycles must be transported through part or entire circumference of the cutting drum. This transportation of already recovered coal through the cutting zone of rotary head makes it a rotary grinder. Some of the coal particles will be subjected to secondary fragmentation or regrinding in the process. The potential effect on dust generation by regrinding is significant because the cutting head utilizes kinetic energy to comminute recov¬ered coal material. The moving bits and bit blocks on the cutting head impact coal particles and transfer some of their kinetic energy to the particles. After obtaining kinetic energy, coal particles are free to impact one another and they also impact the coal seam or cutting head. During impact, high impact force and high internal stress concentration are created in the particles. Kinetic energy is transformed into strain energy. When stored strain energy exceeds allowable strain energy, the particles will break. A great amount of respirable dust will be generated due to impact failure. In reality, regrinding occurs at the same time as primary cutting. The particles to be ground are the result of primary cutting. Both primary cutting and regrinding produce dust. Therefore, it is impossible to separate regrinding from primary cutting. In order to study respirable dust generation by regrinding and analyze the influencing parameters, a laboratory approach was adopted. In this approach, it is possible to study the regrinding separating from primary cutting."

Mar 1, 1992

By Vern L. Kegler

This paper is one off a series dealing with mining methods and costs, sponsored and published by the United States bureau of Mines. ACKNOWLEDGMENTS The author acknowledges the, constructive and helpful suggestions and criticism of W. F. Lamoreaux, vice-president, and general manager of the Ducktown Chemical & Iron Co. United States Geological Survey Professional Paper- 139, by W. H. Emmons and F. B. Laney, has been drawn upon for some of the information contained in the paragraphs or history and geology.

Jan 1, 1931

By Scott W. Hazen, George W. Gladfelter

This report presents the results of an initial investigation into some problems resulting from the use of assays representing unequal sample interval lengths and the use of the weighted average grade of ore in evaluating bedded mineral deposits . A mathematical proof and examples are given to show that the unweighted and weighted assay averages are equivalent when there is no correlation between assay value and sample interval length but that these averages are different when there is correlation between assay value and sample interval length . The amount of this difference between estimates is a function of the degree of correlation . One set of sample and assay data , based on 11 stratigraphic sections of the Phosphoria formation in Idaho , indicates that the relationship between the amount of difference between estimates and the correlation factor is approximately linear . If this correlation relationship can be established , within acceptable limits of precision , as a consistent attribute of deposits , the estimate of weighted average grade of ore could be predicted directly from the unweighted estimate of grade of ore by using the relationship as a prediction factor . Randomness tests on the sample and assay data from the Phosphoria formation , using the mean - square - successive - difference method , indicate that correlation between assay value and sample interval length ( each sample interval length represents an individual bed or stratum of the formation ) , apparently has little effect on the independence between successive assays , between successive sample interval lengths , and between the products of assays and sample interval lengths . Therefore , these data can be analyzed statistically as long as the original sample sections have been selected at random for sampling .

Jan 1, 1964

By B. J. Scheiner

Extraction of molybdenum from molybdenite ore by an electrolytic oxidation procedure was investigated by the Bureau o f Mines. Various parameters affecting molybdenum extraction, such as salt concentration, temperature, treatment rate, current density, and particle size, were studied. Molybdenum extraction of 95.2 percent was achieved on a laboratory scale from an ore containing 0.35 percent molybdenite. Corresponding power consumption was 24 kwhr per pound of molybdenum extracted with a base consumption of 4.5 pounds of sodium carbonate. Laboratory and pilot plant experiments are in progress on low-grade molybdenum concentrates containing rhenium and copper. Preliminary results indicate that molybdenum extractions in the 90- to 99-percent range and rhenium extractions of 93 to 99 percent can he obtained without appreciable oxidation of associated copper minerals.

Jan 1, 1972