Search Documents

By A. W. Khair, M. Ahmad, Gehi. L. D.

"This paper presents an analysis of the effect of the dynamics of bit wear on dust generation. Two surveys have been conducted in order to assess the mechanism and type of bit wear and to evaluate the impact of bit wear on the productivity of the continuous miners. Used bits were collected from the underground coal mines and these used bits were utilized in laboratory coal cutting. The effect of bit wear on dust generation has been quantified and its impacted on dust generation and ventilation system has been exemplified.INTRODUCTION Research has reduced the prevalence of Coal Workers Pneumoconiosis from 15 to 5 percent according to NIOSH reports (Breslin 1982). However CWP still have not been eliminated as a hazard to mine workers. To prevent coal workers from having black lung MSHA has established a very strict standard for coal mine operations (2.0 mg/m3 with silica content equal to or less than 0.1 mg/m3,). There are numerous coal operations still experiencing great difficulty with meeting the 2mg/m3 dust standard. Among these are the longwall sections and continuous mining sections. In order to meet the rising demand of energy and coal, the number of longwall operations and continuous mining operations would have to be increased. Thus a long term research commitment is required to develop basic solutions that are more generic and greater benefit to the mining and mineral industry.In continuous-mining operations, the miners are exposed to the dust produced during the fragmentation of the coal from the face plus the dust produced during loading and transferring of the coal. The fragmentation process generates most of the respirable dust. The amount of dust generated during fragmentation depended on the coal properties, cutting parameters and cutting bit configuration. Bit wear changes bit configuration, therefore, it also affects dust generation. Bit wear can be defined as the removal of material from surface as a result of mechanical action. In soft coal mines bit wear may not be a serious problem but in hard coal seams bit wear is very significant. In addition, as the good coal seams are depleted, the operators are mining thin seams and the seams with rock partings. During cutting these seams operators are sometimes forced to cut roof and floor rock or rock partings which result in more rapid wear of bits."

Nov 1, 1995

By Harry G. Dosh

Sillimanite, kyanite, and andalusite are aluminum silicates having the same chemical composition (Al2SiO5) and are used in the ceramics industry for the manufacture of high-grade refractories. Natural sillimanite with added corundum or other alumina to just short of mullite (3Al2O3 -2SiO2) proportions is unequalled for jobs wherein strength at high temperatures, resistance to spalling, and resistance to slagging by acid slags are desired. High-grade porcelain ware also requires these minerals. At the same cost, sillimanite would be preferred for most uses, but the lack of any large source of sillimanite bas given economic preference to kyanite or andalusite for special refractories and high-grade porcelain wares. Sillimanite-bearing schists were observed in Spartanburg County, S. C.; as early as 1937 by D. Hoye Eargle, geologist with the U. S. Soil Conservation Service. The mineral was not identified until 1942, when Miss Jewell Glass, of the U. S. Geological Survey, examined several of the deposits. This identification was confirmed in 1943 by Dr. Laurence L. Smith, of the University of South Carolina, when he examined the Spartanburg County deposits and found numerous additional occurrences of sillimanite schist in Greenville County. Subsequent work by the Bureau of Mines and the South Carolina Geological Survey has been responsible for the location of additional sillimanite-rich schist deposits in Spartanburg County. Between October 1, 1948, and November 21, 1948, the Bureau of Mines conducted an exploratory diamond-drilling project on the John Gideon property in the southeastern section of Spartanburg County (fig. 1) and drilled a total of 681.7 feet in six holes. Drilling indicated that the deposit is relatively shallow, as no ore was cut below the zone of weathering.

Jan 1, 1950

By W. W. Culter

"This paper is the outcome of thorough investigation into the value of the previous methods used for deriving production decline curves. It is highly important that methods be employed that are fundamentally sound and also practicably applicable. Six methods commonly used were studied. Some of these were found to be fundamentally in error; some save reliable curves but involved much work and time in the preparation; others gave reliable curves with less time and effort.It was found that of the methods previously employed the ""family curve"" method described in Bull. 134 Amer. Inst. Feb. 1918, pp. 499-500 by Lewis and Beal, was probably the most satisfactory. The now method given in this paper ploys the same principles as the ""family curve"" method, but is mathematical instead of graphical,The engineer and the oil man should carefully boar in mind both the use and the limitations of the average production curve such as is derived by the ""family curve"" method or other methods mentioned. Estimations of future productions or of underground oil reserves of a particular tract or well should be made from the production records of the tract or the well itself wherever such records are satisfactory. The use of the average curve of a district or field should be applied only to those properties or wells where there are not sufficient data to construct individual or tract production records, or where the productive life so short that a satisfactory individual record can not be obtained."

Jul 1, 1920

By Louis A. Panek

Tests of mine-roof models in a centrifuge show that the suspension effect due to bolting a horizontally bedded mine roof with frictionless surfaces of contact between beds depends principally on the number of bolted beds and their relative flexural rigidities, provided that sufficient bolt tension is exerted to prevent strata separations at the bolt locations. Strata separations tend to occur in the unbolted roof mainly because the beds have unequal thicknesses. "Suspension effect" refers to the transfer of part of the weight of weaker or thinner beds to the flexurally more rigid beds by roof bolts or by any other means. The factors investigated were number of beds in the bolted unit, bed thickness, modulus of elasticity of beds, length of bolts, spacing of bolts across and along the opening, bolt load, and intensity of roof load. The general principles of behavior of the bolted roof beds are explained by an approximate theory. Model test data are used to validate the theory and to obtain an expression for the "suspension efficiency". As the suspension effect actually observed in the models is smaller than that predicted by the approximate theory, the suspension efficiency in general is less than unity. Mathematical expressions are obtained for (1) the change in roof bending stress due to the suspension effect, which is needed for design of a roof-bolting system, (2) the change of roof deflection due to the suspension effect, which may be useful for evaluating the effectiveness of a roof-bolting system, and (3) the bolt load or pre-load that is required to achieve the desired reinforcing effect.

Jan 1, 1962

By E. C. Lane

This report on properties of commercial motor fuels is the twelfth in a series made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the United States Department of the Interior. The first report contained data on motor gasolines sold during the winter of 1935-36.3/ The -present report, covering the summer of 1941, presents analytical data for 1,857 samples, representing the products of approximately 135 companies. -As in previous surveys, these companies include both large and small suppliers. In addition, the Pacific coast is represented by data averaged by the Pacific Coast Technical Group before being submitted, and these data are published exactly as they were received. Conforming to previous surveys, the data cover three groups of samples -- regular-price, premium-price, and third-grade gasolines -- and each group has been aver aged separately. The number of samples, items, and brands comprising each group, exclusive of those of the Pacific coast, are as follows: Regular price, 1,010 samples, 291 items, and 86 brands; premium price, 577 samples, 263 items, and 78 brands; third-grade gasoline, 270 samples 159 items, and 74 brands. The meanings of these terms as used in the surveys are as follows: Sample: The individual supply of gasoline obtained at the filling station and analyzed in the laboratory.

Jan 1, 1942

By James P. McGee

Preliminary calculations show an economic advantage in using nuclear energy to supply the endothermic heat required for gasifying coal. It should be noted that the various assumptions used in preparing these calculations must undergo further evaluation through additional engineering design and research. The proposed system for gasification is the indirect process cycle with helium heated in a nuclear reactor and passed through an exchanger-type gasifier for the reaction of coal and steam to form CO (carbon monoxide) and H2 (hydrogen gas).

Jan 1, 1960

By D. C. Dahlin

The Bureau of Mines has investigated podiform chromite deposits in three ultramafic bodies in the Caribou Mountain and lower Kanuti River areas of central Alaska. The investigation, reported in two parts, was done as part of the Bureau's mission to help insure an adequate supply of minerals to meet the Nation's needs. Part I describes an extensive field investigation and mineralogical studies by personnel from the Bureau's Alaska Field Operations Center. This report, part II, describes the mineralogy of 11 samples that were high-graded from surface exposures at 10 sites and presents the results of laboratory batch beneficiation tests designed to concentrate the chromite. The 11 samples, peridotites and chromitites that consisted of variable amounts of chromite or chromium-bearing spinets, olivine, and serpentine, were beneficiated by grinding and sizing, gravity concentration, and electrodynamic separation. Three high-chromium chromite concentrates, two high-iron chromite concentrates, and one high-aluminum chromite concentrate were produced. Three other concentrates were marginal, and two were submarginal. Chromium recoveries ranged from 54 to 92 pct. These results indicate that the areas may be significant chromium resources. Potential platinum association with the chromite was also investigated. Analysis of these 11 samples indicates that the areas are not good platinum resources.

Jan 1, 1983

By F. E. Block

This investigation was made as part of a larger program to develop basically new methods for preparing yttrium metal in high-purity form. It was performed under a cooperative agreement between the U.S. Atomic Energy Commission (AEC) and the Federal Bureau of Mines. Laboratory-scale tests were made to devise methods for preparing high-purity, anhydrous yttrium trichloride, for reducing the yttrium trichloride with sodium or lithium, and for consolidating the resulting yttrium sponge into ingots.

Jan 1, 1960

By W. H. Hamilton

The Kokomo (Tenmile) mining district has had an output valued between $20 and $30 million, mostly from production of silver, lead, and zinc, since 1878. For many years before World War II, there was little production, as the complex nature of the ores made them unattractive at existing metal prices. Under the stimulus of the war, the Geological Survey and the Bureau of Mines studied they district, and in October 1944 the Bureau of Mines began an exploration project, which included dia¬mond drilling, bulldozer trenching, and geophysical surveying. Project work was continued until March 1949, except for short recesses during 1945, 1947, and 1948. Forty-five diamond-drill holes, totaling about 13,000 feet, were drilled from underground and surface stations on the various properties in the district. Eleven bulldozer trenches, abut 2,400 linear feet, were excavated in an attempt to uncover the outcrop of the middle Quail limestone. These trenches ranged from 100 to 485 feet in length and reached a maximum depth of 15 feet. A limited geophysical investigation was made during the summer of 1946. The length of the traverses were: Magnetic, 990 feet; resistivity, 6,250 feet; and self-potential, 69,780 feet.

Jan 1, 1955

By W. H. Tomlinson

During the 9 years ended December 31, 1938, 188 fatalities resulted from preventable accidents in and around the coal mines of Indiana; 173 of these occurred at underground mines and 15 at stripping or open-cut operations. In addition, there may have been other unrecorded fatalities during this period. The two organizations receiving notice of accidental deaths at coal mines in this State are the Division of Mines and Mining and the Indiana Industrial Commission. Only deaths occurring at underground mines employing 10 or more men are reported to the former, as neither strip mines nor underground mines employing fewer than 10 men cone within the purview of the Indiana mining law. The mine inspectors have no Jurisdiction over this latter group of mines and do not inspect them. Fatalities at small "wagon" mines and open-cut operations are supposed to be reported to the Industrial Commission; however, in many instances deaths at small mines are not reported, the only record being a death certificate filed with the county or corporation health officer. Thus, many deaths in small mines escape attention, especially when the victim succumbs some time after the injury was received. The data presented here on fatalities in Indiana, during the past 5 years include several instances in which the only record available is a death certificate; possibly others have been overlooked. From 1934 to 1937 the fatality record was progressively worse, that of the larger underground mines in 1937 being more than twice the average for these mines for the previous 4 years and only slightly less than twice the average for all mines, including open-cut operations. The increase in deaths during 1937 was due to two explosions, with 20 fatalities in one and 2 in the other. The number of deaths in the larger underground mines was considerably less in 1938 than in the previous 4 years, but there was no improvement in the number of fatalities at the small mines, or at open-cut mines.

Jan 1, 1940

By Allen D. Look

Uninterrupted shaft operations are an important economic factor in mine operation, and good shaft support is an important aid in preventing accidents and interruptions. More permanent supports can cut the hazards, costs, and delay incident to replacement of conventional timbers, especially where subject to decay. Installation of prestressed, precast concrete shaft supports in 100 feet of shaft at the Banner mine, Lordsburg, N. Mex., nave a satisfactory permanent installation in a section of shaft that had given trouble with conventional timbering. Use of rock bolts supporting gunited wire netting around the rock walls of the shaft prevented sloughing. No attempt was made in this paper to arrive at comparative costs of installation of various types of support. However, it was indicated that use of a lighter weight aggregate would be desirable in further use if prestressed precast members as placed in the Banner mine.

Jan 1, 1957

To restore ventilation and prevent the accumulation of explosive or toxic gases by quickly installing substitutes for stoppings blown down by an explosion. Approach Temporarily replace blown down stoppings with a parachute-shaped brattice which can be erected in minutes. How It Works The self-sealing brattice is secured to the roof, ribs and floor by anchoring its nylon edge strip at several points using extensible poles, shads, or available projections such as roof bolts. The air pressure in the entry pops open the chute of lightweight sailcloth, forcing it tightly against floor, roof and rib. See Figure 1. This emergency brattice has been tested at two locations in the Bureau's Experimental Mine at Bruceton, Pennsylvania. In a test last December, one MESA inspector wearing full rescue apparel (including self contained breathing apparatus) installed a self sealing brattice in an entry at the Bruceton Mine. Although he did not have any previous experience with the device, he easily erected it in slightly less than 10 minutes, using two extensible supports (pogo sticks). Research to improve and refine the self-sealing brattice is continuing.

Jan 1, 1977

Now you know why there is concern about mine illumination. You have some idea about how the human eye works and about the problems of glare, peripheral vision, and accommodation. And you know that lighting in a mine presents special problems because of the dark surroundings and low reflectance. This chapter describes what can be done to improve conditions. This chapter begins with a short discussion about Federal Standards on mine lighting -- what they are and what is being done to carry them out. The chapter then describes different types of lamps that can be used for mine lighting, and discusses their advantages and disadvantages. Finally, the chapter lists some things that you can do personally to improve lighting, or can point out to others so that improvements can be made. The Federal Government is doing its part to improve mine lighting by establishing regulations. Lamp manufacturers are constantly studying new lamps to provide better equipment. And your company will do its part to comply with regulations. Better lights may not be here yet, but they will be soon. But in the end, you are the one who will be using the lights, and you are in the best position to see the improvements. You are also in the best position to see and tell others where further improve¬ments can be made.

Jan 1, 1976

By ALBERT C. DURHAM

In anthracite mining , pumping is a problem of major importance , and water must be handled and rehandled in almost every mine whether the mine is in operation or idle . The motor - driven centrifugal pump is the most commonly used type of unit for the large pumping installations, and experience has . proved that fully automatic control has certain advantages over manual control . Some of these advantages are greater safety for maintenance personnel , continuous protection against faulty operation , which could cause damage to the Lumping apparatus , and lower pump -room operating costs .

Aug 1, 1948

By Almon F. Robertson

"INTRODUCTION AND SUMMARYThis is one of a series of reports describing investigations within the Missouri River Basin in Montana conducted by mining engineers of the Bureau of Mines, Minerals Division, Region II. The primary purpose of these investigations is to provide basic information to agencies of the Department of Interior and others concerned with the planning of power and other water developments in the basin. This report contains only such factual data as have been authorized for public distribution. Special precautions have been taken not to reveal any information or data that are considered confidential.The field investigations for this report were made during the summer of 1949. Virtually all known metallic mineral deposits in the county and same nonmetallic (industrial) mineral deposits were investigated. Most of the mines and prospects have been inactive for many years. The old underground workings generally are only partly accessible; many are entirely inaccessible. Most of the mining claims were located many years ago, and a considerable number were patented. Many claims were abandoned; others were relocated. Nimes and ownerships often have changed. Because of such conditions, much of the information on most of the mines and prospects necessarily has been obtained from available Federal and State publications, private geologists' and engineers' reports, and from owners and local residents.Metal mining in Cascade County, Mont., has been confined mainly to the silver-lead-zinc deposits in the Montana (Neihart) and Barker districts in the southeastern part of the county. The Neihart district has yielded by far the greater part of the county's metal output. The mines generally have been operated intermittently, largely because of fluctuating or low silver and base metal prices."

Feb 1, 1951

By Pamela J. Watson

The U.S. Bureau of Mines has demonstrated in laboratory tests that drilling with surface-charge-neutralizing concentrations of polyethylene oxide (PEO) polymer solutions simultaneously improves penetration rates and extends bit life. The applicability of this additive to improve drilling performance in coal measure rocks was demonstrated under field conditions at an abandoned mine land site in Pennsylvania and a producing coal mine property in Ohio. Penetration rate improvements ranging from 15 to 50 pet were obtained when core drilling through a variety of coal measure lithologies. Drilling cost analysis indicates that the small added cost of using the polymer is more than offset by the savings that result from demonstrated increased drilling penetration rates, which translate into drilling cost savings of about 10 to 30 pct. This report also gives chemical analyses of a variety of coal measure rocks and some corresponding local drilling water samples, obtained from a wide geographical base, along with threshold concentrations of PEO required to effect the improved drilling performance in these rocks. From these data, the threshold PEO concentrations needed to ensure improved drilling performance can be estimated for any coal measure rock suite. Proper techniques for mixing PEO solutions are also presented.

Jan 1, 2010

By J. L. Shultz

The investigation of organic compounds in respiratory coal dust by high-resolution mass spectrometry has shown that the organic components differ (1) with particle size, (2) with rank of coal, (3) in coals of same rank from different coal seams, and (4) in respirable mine dust and respirable coal dust (prepared) from the same mine. The eight respirable mine dusts studied are from coal seams in the Appalachian region where the incidence of coal workers' pnumoconiosis is relatively high. The molecular weights of the major organic components vary greatly among these respirable mine dusts; three show strong concentrations of polynuclear aromatic hydrocarbons.

Jan 1, 1972

By Gerald L. Finfinger

The Bureau of Mines conducted an experimental degasification project in Island Creek Coal Co.'s Virginia Pocahontas No. S mine. Methane from the overlying Pocahontas No. 4 coalbed was entering mine workings in the Pocahontas No. 3 coalbed through fractures in the roof rock. Small-diameter (l-S/B-inch) holes were drilled into the overlying coalbed to reduce the gas pressure and intercept methane flows, which were piped to the surface through an underground 6-inch-diam steel pipeline. The total methane flow rate from the vertical holes averaged 150,000 ft3/day for the first month. Methane flows into the mine were reduced by 47 pet, thereby demonstrating the effectiveness of this form of degasification in reducing ventilation requirements and providing a safer working environment.

Jan 1, 1979

By R. H. Jefferson

This Bureau of Mines report describes a series of rapid wet chemical methods for the analysis of blast furnace slags. A "complete" analysis for total iron, manganese, silica, lime (calcium oxide), magnesia (magnesium oxide), sulfur, and mixed oxides (R203) can be routinely performed in less than 3 hours. These methods were employed as the analytical control procedures for the Bureau's experimental blast furnace operations and have been satisfactorily applied to the analysis of other slags and calcareous materials.

Jan 1, 1974

By C. E. Armantrout, H. Kato, M. I. Copeland

The data collected during this investigation indicate that the chromiumgadolinium system has extensive liquid immiscibility and one eutectic point . Liquid immiscibility occurred at temperatures above the monotectic isotherm , 1,830 ° C , which extended from less than 0.25 to about 85 weight - percent gadolinium . The eutectic was at 96 percent gadolinium and 1,170 ° C. Gadolinium and chromium were the only phases in this system . There was a solid solubility of less than 0.25 percent gadolinium in chromium at 1,730 ° C and less than 0.10 percent chromium in gadolinium at 1,160 ° C. The alloys were prepared by nonconsumable - electrode arc - melting , and the alloy system was investigated by heat treatment , metallography , thermal analysis , and X- ray diffraction . All the melting , heat treatments , and thermal analyses were conducted in a vacuum or in helium because of the reactivity of chromium and gadolinium with the components present in the atmosphere at elevated temperatures .

Jan 1, 1964