Search Documents

Endless lines at service station gasoline pumps, limited travel at reduced speeds, thermostats set at an uncozy sixty-eight degrees in the dead of winter-these are but a few of the inconveniences and discomforts that awakened Americans to a realization that our domestic minerals resources, traditionally taken for granted, are not boundless. We begin to accept and practice principles of conservation, yet we are aware that this alone cannot appreciably forestall the inevitable depletion of our minerals, metals, and fossil fuels-resources critical to our Nation's economy. The key to warding off shortages is the development of technology that will insure a continuing, adequate supply of minerals and energy from reliable sources at the lowest possible costs to society and the environment. The mission of the Bureau of Mines is to develop this improved technology. Established in 1910, the Bureau of Mines of the Department of the Interior is the Federal Government's primary research arm in the minerals and fossil fuels fields. In addition to its research role, the Bureau keeps the Government informed of the Nation's mineral posture. The Bureau also seeks to stimulate private industry, through the awarding of grants and contracts, to produce minerals and fuels at a rate compatible with the country's increasing demands.

Jan 1, 1974

By David K. Ingram

The Bureau of Mines conducted underground mapping and rock strength tests to describe and analyze mine roof conditions surrounding ancient stream channel deposits (paleochannels) in the Pittsburgh Coalbed in southwestern Pennsylvania. Paleochannels in the study mine consist of sandstone and/or siltstone and affect the Pittsburgh Coalbed through erosion and/or differential compaction. Differentially compacted sediments within and adjacent to channel deposits caused slip planes, faults, clay-dike faults, clastic dikes (clay veins), coalbed rolls, and slumped structures. Paleochannels can be predicted by recognizing these features and associated sediments, which allows for modification of long-and short-term mine planning and development. Mine entries located beneath the paleochannel deposits exhibit less stable roof conditions than entries with normal (nonchannel) roof. Paleochannel deposits comprise only one-fourth of the mapped study area; however, they contain one-half of the hazardous roof. This study deter-mined that rock strength evaluations, including rock quality designation (RQD), unconfined uniaxial compressive strength testing, and point-load testing, must be accompanied by underground observations. Suggested remedial support techniques include angled and/or longer tensioned bolts, steel mats or crossbars, steel sets or cribbing, and roof trusses.

Jan 1, 1987

By Slavoljub D. Maksimovic

The Bureau of Mines, through a memorandum of agreement with the State of Ohio, tested a method of constructing seals in abandoned mine openings in Ohio by means of pneumatic stowing of crushed limestone and gravel with sand. A total of five openings and one shaft were back-filled. Pneumatic stowing uses compressed air to convey material through a pipeline and into the mine opening. The stowing equipment consists of a power supply, a blower, a feeder to inject the material into the pipeline through an airlock, and a nozzle for directing the placement. Material is ejected from the nozzle at high velocity, creating a high-compaction fill upon impact. Well-graded aggregate up to 2 inches in diameter and having sufficient fines is used as fill. The stowing method is safer and faster than conventional methods, is cost competitive, prevents trespass into abandoned mine openings, and eliminates or reduces the exposure of workers to possible hazards since the discharge nozzle can be kept at the mouth of the opening. The equipment is mobile, and, with some modification, the technique could be widely used for sealing abandoned and active mine openings, even in remote locations and during severe weather conditions.

Jan 1, 1982

By Albert L. Toenges

[sing tho ppsf; few Yomn t!le:.c. hcs beer. p. trqnd away frorn locomotive haulwe of cop2 frorn tile losdiw point to tho prop,nration plant of bitu~i- nnus-cod strip mlncc to a;~to~lzcd. h,71Jlr.:~. The qrostion has arisen rrhethcr this is alwqvs econ~nicd, rxcl the purpcrse or' tnf s investigation is to de- termine, if possible, the econonic limlt for ~~torieod had.we. sing tho ppsf; few Yomn t!le:.c. hcs beer. p. trqnd away frorn locomotive haulwe of cop2 frorn tile losdiw point to tho prop,nration plant of bitu~i- nnus-cod strip mlncc to a;~to~lzcd. h,71Jlr.:~. The qrostion has arisen rrhethcr this is alwqvs econ~nicd, rxcl the purpcrse or' tnf s investigation is to de- termine, if possible, the econonic limlt for ~~torieod had.we.]

Jan 1, 1938

By H. Kenworthy

Sulfide-ore concentrates containing cobalt, nickel, copper, lead, and iron from the operations of the National Lead Co. at. Fredericktown, Mo., were treated successfully on a laboratory scale to recover more than 90 percent of the cobalt, nickel, and copper. A cobalt -nickel-bearing, lead-copper matte., produced by the St. Joseph Lead Co. at Herculaneum, Mo., was treated to produce a lead-zinc fume, a copper sulfide concentrate, and a cobalt nickel-iron product, netting a recovery of over 75 percent of the cobalt and about 90 percent of the nickel and copper. National Lead Co. bulk concentrates were chlorinated with gaseous chlorine to form anhydrous metal chlorides and sulfur chlorides, sulfur chlorides were recovered by distillation, a high percentage of the ferric chloride was converted to ferric oxide, and the chlorinated residual metals were extracted with water. Metal ions were removed from leach liquors by pH-controlled fractional precipitation as hydroxides. Cobalt solutions "were prepared from cobaltic hydroxide, and procedures were developed to remove contaminating metal ions. Purified cobalt solutions were employed as electrolytes for deposition of high-purity cobalt.

Jan 1, 1953

The purpose of this study was to examine the problems of underground coal mining in the United States, and to develop recommendations for an integrated Research and Development Program aimed at resolving these problems. Specific objectives of the study were as follows: ? To identify the existing inadequacies that have adverse effect on Health, Safety, External Environment, and Productivity. ? To identify opportunities for technological advance s to correct these inadequacies. ? To develop an integrated Research and Development Program designed to accomplish the advances identified. Many of the recommended tasks are dearly long range; this is especially true of those for study of future mining systems. However, funding recommendations in this Report are presented for a 5 -year period, since the developments accomplished during this period will undoubtedly be a factor in the formulation of the follow on tasks. Where applicable, the recommended Research and :Development could include development and test of pilot model equipment.

Jan 1, 1970

By Catherine C. Kilgore

The Bureau of Mines investigated the availability of fluorspar (CaF2) from 36 U.S. and 50 foreign mires and deposits in 13 countries. Only 6 U.S. properties are considered to be economic, as 29 domestic deposits were found to have an average total cost of production that was uneconomical at a breakeven (0-pct) discounted-cash-flow rate of return (DCFROR). The 50 foreign properties evaluated represent at least 55 pot of demonstrated fluorspar resources located in market economy countries and China. Al I evaluated foreign operations were found to be economic to marginally economic in January 1984 dollars when compared against published prices for each country. Reserves for 56 properties totaled 97 million metric tons (mt) (recoverable Ca F,) from demonstrated ore resources of 344 million mt that contained 123 million mt CaF2. The average total cost needed to cover all costs over the life of each operation was determined for all recoverable fluorspar products. Comparisons of ruining, beneficiation, and transportation costs per metric ton of fluorspar concentrate illustrate advantages between countries. Of the three countries with the greatest fluorspar production, China, with its high-grade, low-cost operations had the lowest weighted-average total cost of production ($38/mt concentrate), Mexico was next, at $54/mt concentrate, and benefited in U. S. dollar terms from the devaluation of the peso. The Republic of South Africa needed an average of $90/mt of concentrate to cover all costs of production at its large low-grade deposits.

Jan 1, 1985

By M. A. Trevits, A. Ozmet, A. C. Smith, J. B. Walsh, T. P. Mucho

Improvements in remote fire fighting technology are needed to reduce miner exposure to the dangers of fires and possibly save the lives of those who may become trapped. The National Institute for Occupational Safety and Health, in cooperation with U.S. Foam Technologies, Inc1., conducted a series of experiments at the NIOSH Lake Lynn Experimental Mine to study the stability, transport, control and fire extinguishing effectiveness of nitrogen-enhanced foam technology. This paper presents a description of the mine test configurations and experimental results

By R. V. Ramani

One area of study in the Coal Mine Injury Analysis project was to illustrate and enhance the ability of mine safety management personnel to apply analytical techniques to injury experience data and to justify requests for funds for safety enhancement actions on a cost/benefit and other quantitative basis. Four volumes of this final project report detail (1) the objective and scope of the mine safety management research, (2) the results of literature review, and case studies, and (3) models developed for mine safety management. The four volumes are titled as Volume III: Mine Safety Management, Volume IV: Analytical Techniques for Mine Safety Management; Volume V: Mine Safety Management Case Studies and Volume IX: Training Cost Model. In this volume, the following material is presented: (i) review of related literature, (ii) mathematical models to perform quantitative analyses of accident/ injury experience data using the tools and techniques of risk analysis, time series analysis, and the Markov process, and (iii) descriptions of the HDBSEL and ACIM programs which are used to perform accident/injury experience analyses and cost analyses, respectively.

Jan 1, 1993

By V. F. Parry

The object of this report is to present certain pertinent data on the physical and chemical properties of South Arcot lignite and to present the results of several special tests to show how the raw lignite can be upgraded to superior fuels for certain special uses. The Bureau of Mines Branch of Coal Technology laboratories at Denver have advocated the drying and carbonization of all low-rank fuels for special uses and have introduced and developed new techniques for upgrading and refining noncoking coals. Application of these techniques to the South Arcot lignites was the object of the investigation, and this report presents significant data necessary for planning a fuel program based on utilization of dried and carbonized dusts. In general, the South Arcot lignite is similar in chemical properties to the high-moisture lignites found in the United States and has some physical properties similar to Australian brown coals. The samples submitted for test had lost moisture before delivery to the laboratory, and it has been necessary to estimate the analysis of the lignite in place in the mine. Various observations made in India by qualified technicians indicate that the bed moisture content of the entire seam is in the range of 54 to 56 percent. For estimating purposes in this report, the bed moisture content has been taken as 56 percent and the ash content of the fresh coal as 2.5 percent. The average analysis estimated for the as-mined lignite is: [Moisture percent 56.0 Volatile matter do.22.0 Fixed carbon do.19.5 Ash do.2.5 Heating value B.t.u. per lb. 4,890]

Jan 1, 1957

As mine haulage vehicles become larger, the danger to a driver during a fire emergency is increased by the greater height of the cab above ground. Also, property damage due to fires on bigger trucks can be substantial. To solve this problem, the Department of Interior's Bureau of Mines, through two research and development contracts with FMC Corporation, San Jose, California, has developed two reasonably priced, reliable automatic fire sensing and suppression prototype systems for large haulage vehicles. At the onset of the large mobile equipment fire protection contract effort, it was learned that fires were frequently experienced in open-pit mine haulage equipment, especially large trucks. As the size of equipment has grown, so has the hazard presented to an operator forced to leave his truck in a hurry when fire breaks out and his normal path to the ground is blocked by flames. His only recourse is to jump from the cab platform to the ground, and the one-story drop of 10 feet or more can severely injure him. It is with these factors in mind that a program was undertaken to provide a fire detection and extinguishing capability tor the large mobile equipment, especially trucks, used in open pit mines.

Jan 1, 2012

By Henry P. Chandler

[Diamond, because of its extreme hardness and abrasion resistance, has an important function in precision engineering and automation. With the increasing; requirements of modern production for fine tolerances, interchangeability, and speed, it has become even hors, important in spite of the supply of other abrasive and hard materials and of ultrasonic, electrospspark rued other substitute grinding methods world industry seems likely to absorb large quantities of diamond for industrial purposes. An increasing part of the world's needs will be supplied by manufactured diamond, which was introduced commercially by General Electric Co. in 1957. Use of diamond for glass cutting goes bark several centuries, mid diamond drilling of rock became important to the mining industry M the 1870's. Today, diamond drilling is the most extensively used method of exploring the world's ore reserves; diamond drills two also used to determine the nature of bedrock below the foundations of buildings, dams, and bridges. Diamond drill bits are now used extensively in the petroleum industry, and replacement or steel rock bits with diamond drill bits in hard rock formations has effected substantial savings.]

Jan 1, 1964

By Henry P. Chandler

[Diamond, because of its extreme hardness and abrasion resistance, has an important function in precision engineering and automation. With the increasing; requirements of modern production for fine tolerances, interchange-ability, and speed, it has become even more important. In spite of the supply of other abrasive and hard materials and of ultrasonic, electrospark rued other substitute grinding, methods, world industry seams likely to absorb large quantities of diamond for industrial purposes. An increasing part of the world's needs will be supplied by manufactured diamond, which was introduced commercially by General Electric Co. in 1957. Use of diamond for glass cutting roes bark several centuries, mid diamond drilling of rock became important to the mining industry M the 1870's. Today, diamond drilling is the most extensively used method of exploring the world's ore reserves; diamond drills two also used to determined the nature of bedrock below the foundations of buildings, dams, and bridges. Diamond drill bits are now used extensively in the petroleum industry, and replacement or steel rock bits with diamond drill bits in hard rock formations has affected substantial savings.]

Jan 1, 1964

By William F. Jahn

Because of the' situation in Europe during the summer of 1939, with the possibility of war and consequent curtailment or loss of supplies of tin to the United States, the Bureau of Mines undertook an investigation of domestic tin resources. This was permitted by the Strategic Minerals Act of 1939, which authorized investigation of possible domestic resources of strategic minerals necessary in a national emergency. The minerals selected were in short supply, and the United States depended almost entirely on imports to meet normal requirements. The Black Hills of South Dakota were selected for investigation as one possible source of tin because of the occurrence of the mineral there has been known since 1876, although production had never been important. The Tinton area, in the northern part of the Hills, had received the most attention and contained some minor indicated and inferred tin deposits.

Jan 1, 1949

By Charles E. Whieldon

The importance of producing more oil from known petroleum reserves has placed increased emphasis on the application of secondary-recovery methods. Recently published reports3 4/ describe the results of waterflooding in Roane and Pleasants Counties, W. Va. (see fig. 1.) This report describes the Barron Kidd Oil Co.?s Santee waterflood project, Maxton sand, Burton field, Church district, Wetzel County, W. Va. (See fig. 2.) The Federal Bureau of Mines hopes that these reports will stimulate interest in improved waterflooding techniques, thereby discouraging premature abandonment of oil leases.

Jan 1, 1961

By Ernest J. Conway

Seventy-four human factors research and development projects were identified for possible Bureau funding. The projects were based on (1) literature surveys, (2) reviews of accident statistics and reports, (3) interviews with equipment manufacturers, MSHA, and Bureau personnel, and (4) site visits to 26 mines. The projects are divided into the following categories: those related to (1) mobile equipment, (2) maintenance shops and areas, (3) plants and mills, (4) organizational factors, (5) safety programs/data, and (6) training. The projects were rated by industry and MSHA people in terms of benefit to the industry. Projects were placed into three categories of priority. The highest priority contained 25 projects with 26 in Category 2, and 23 projects in the lowest category.

Jan 1, 1982

By C. W. Van Noy

The procedure suggested in this report is intended for the use of engineers, esters, accountants, etc., in estimating the cost of chemical-type operations. It is intended to over operating costs, not investment costs, as the latter have been covered numerous other publications. However, as capital investment costs are reflected to a high degree in operating costs, it is important to point out that accuracy of investment costs is highly essential. Therefore, all factors that might be included under plant -capital costs should be considered, such as requirements of shops, employees' housing, etc. The procedure is designed primarily for use in types of chemical oper¬ations, such as the production of synthetic liquid fuels, anhydrous ammonia, and others of like or similar nature. Yet, no attempt has been made to cover the entire chemical industry.

Jan 1, 1949

By V. R. Spironello

The Bureau of Mines is involved in research directed toward the conserva¬tion of important raw materials and the utilization of solid waste. Two of the objectives are to conserve high-quality coking coals used for foundry coke and to utilize waste materials of marginal quality but of high calorific value. These objectives are consistent with Bureau goals. Pilot plant cupola trials were made to evaluate the adequacy of various alternative fuels, and to determine to what extent they could replace the foundry coke in cupola charges. Information was obtained on furnace performance, metal and slag chemistry, environmental questions, and the properties of castings. It was shown that anthracite or bituminous coals can partially replace charge coke up to the 40 pet level. Briquetted materials prepared from fuel fines, and waste prod¬ucts or byproducts of high calorific value, all tend to break down on heating in a cupola so that their use must be restricted to below 20 pet replacement. In cases where pitch-bonded coal fines or petroleum coke were used, carbon pickup by the iron was inadequate for gray iron specifications. Although emphasis during this work was placed on basic slag practice, some acid practice results are included.

Jan 1, 1980

By C. Özgen Karacan

Gob gas ventholes (GGV) are used to control methane inflows into a longwall operation by capturing it within the overlying fractured strata before it enters the work environment. Thus, it is important to understand the effects of various factors, such as drilling parameters, location of borehole, applied vacuum by exhausters and mining/panel parameters in order to be able to evaluate the performance of GGVs and to predict their effectiveness in controlling methane emissions. However, a practical model for this purpose currently does not exist. In this paper, we analyzed the total gas flow rates and methane percentages from 10 GGVs located on three adjacent panels operated in Pittsburgh coalbed in Southwestern Pennsylvania section of Northern Appalachian basin. The ventholes were drilled from different surface elevations and were located at varying distances from the start-up ends of the panels and from the tailgate entries. Exhauster pressures, casing diameters, location of longwall face and mining rates and production data were also recorded. These data were incorporated into a multilayer-perceptron (MLP) type artificial neural network (ANN) to model venthole production. The results showed that the two-hidden layer model predicted total production and the methane content of the GGVs with more than 90% accuracy. The ANN model was further used to conduct sensitivity analyses about the mean of the input variables to determine the effect of each input variable on the predicted production performance of GGVs.

Jan 1, 2009

By P. J. Remington

Field measurements utilizing a seat pad accelerometer were made on 25 underground coal mining machines in order to quantify the vibration levels experienced by the operators. Those data were combined with information on the statistics of the operating times of those machines in order to compare the operator's vibration exposure to the criteria in ISO 2631, "A Guide for the Evaluation of Human Exposure to Whole Body vibration." The comparison showed that about 30% to 40" of all underground coal mining machine operators can be expected to be exposed to vibration exceeding the fatigue decreased proficiency criterion, whereas only 10 to 15% would be expected to experience vibration exceeding the exposure limit. The primary sources of the exposure are shuttle cars and possibly scoop trams. Detailed exposure statistics are presented and the implications of the results are discussed.

Jan 1, 1983