Search Documents

By Edward F. Divers

This Bureau of Mines report describes a new type of scrubber (dust collector) and ventilation system built into the auger support frame (boom) of a Jeffrey 120L continuous mining machine. With this twin scrubber arrangement, one scrubber is mounted into each side of the boom. Each scrubber includes a 2,500-cfm fan, a flooded fibrous-bed scrubber panel, and a water droplet eliminator. The system was designed for minimum size and adds only a few inches to machine height. Exhaust duct design allows flexibility with various airflow configurations to suit both blowing and exhaust fare ventilation systems and brattice distances ranging up to 20 feet. Full-scale tests with exhaust ventilation were conducted at a Mine Safety and Health Administration surface facility at Bruceton, Pa., to determine the scrubbers' methane dilution capability. Several configurations of the twin scrubber-ventilation system produced striking improvements in face methane dilution when compared with conventional systems.

Jan 1, 1981

By R. V. Ramani

"The importance of adequate mine ventilation for good health and safety conditions has been recognized since miners first ventured underground. All over the world, governmental actions on mine health and safety arc directly connected with mine atmospheric environments their assessment and control. These governmental actions have been, and continue to be, motivated by the repeated experience that potential threats from inadequate control can evolve, either suddenly or in the long-term, into unpleasant reality, with catastrophic health and safety consequences. These governmental actions arc also an indication of the remarkable professional progress being made in the field of mine ventilation.Surely, no developed country allows underground mines to operate without strong measures for the control of ventilation under legislation specific to the mining industry. In the United States, the federal government's responsibility for mine safety has evolved over the years through a series of legislative actions beginning in 1865 and continuing through 1910, 1941, 1947 and 1952.The passage of the Federal Metal and Nonmetallic Mine Safety Act of 1966 (the 1966 Metal Act), the Federal Coal Mine Health and Safety Act of 1969 (the 1969 Coal Act) and the Federal Mine Safety and Health Amendments Act of 1977 (the 1977 Mine Act) arc the most important milestones in this long legislative history. The 1977 Mine Act adopted many of the stronger features of the Occupational Health and Safety Act of 1970, perhaps the most significant piece of legislation on workers' occupational health and safety in US history.It is worthwhile to ask, ""How far has the United States come in mine ventilation since the enactment of the 1969 Coal Mine Health and Safety Act?"" This Act and its associated regulations defined in great specificity many standards for healthful and safe operation of a mine and. in some cases, what constitutes good ventilation practice."

Nov 1, 1995

By Bruce K. Cantrell, Jon C. Volkwein

Exposure to mineral aerosol is an occupational health hazard in mining and mineral processing industries because of the risk of developing pneumoconiosis. Agricola (1556) described this hazard for metal mining in Carpathia. He described shortness of breath and consumption, conditions that are now associated with asthma and emphysema. By the end of the nineteenth century, several respiratory diseases were known to affect miners, including silicosis and coal workers' pneumoconiosis (Fletcher, 1948; Seaton et al., 1981). For example, silicosis, not tuberculosis, was clearly recognized as the hazard in the Vermont granite quarries and stone-cutting sheds (McFarland, 1927). The Gauly Bridge Tunnel disaster in the mid-1930s caused the deaths of an estimated 700 workers by acute silicosis and focused the nation's attention on this disease (Cherniack, 1986). By the mid-twentieth century, it was clear that risk of simple pneumoconiosis is associated with a miner's cumulative exposure to mine aerosol in the respirable size range and that prevention lies in reducing that exposure through regulation (Seaton, 1986). In the United States, regulation of mine worker exposure to airborne mine dust is the responsibility of the Mine Safety and Health Administration (MSHA) in the U.S. Department of Labor. The key legislation relating to improved mine worker health was the Federal Coal Mine Health and Safety Act, enacted in 1969 (U.S. Congress, 1969) and subsequently amended as the Federal Mine Safety and Health Act of 1977 (U.S. Congress, 1977). MSHA receives technical assistance from the National Institute for Occupational Safety and Health (NIOSH). NIOSH also provides recommended exposure limits (RELs) for contaminants to MSHA. MSHA's regulation of mines includes the establishment of a dust standard administratively based on the these RELs. Some mine operators must submit a dust control plan designed to meet the dust standard. Periodic mine inspections determine if mines are com- plying with both the dust standard and the dust control plans (MSHA, 1991). The most common dust measurements are those for respirable dust (according to the definition given in Fig. 26-7), that is, the fraction of aerosol particles able to reach the gas exchange region of the lungs. The other health-related size fractions (inhalable and thoracic-see Fig. 25-1, and "total" dust) are also occasionally measured. A "total" dust measurement is defined by the common practice of the last 30 years or so, using 25 mm or 37mm plastic cassettes (e.g., from PAL, MIL, SKC ). The types of mines have been categorized

By Albert E. Long

During the summer and fall of 1948 the Bureau of Mines, in cooperation with the U. S. Geological Survey, conducted 6xperiments in diamond core drilling in the Phosphoria formation in southeastern Idaho and southwestern Wyoming. Nearly all of the diamond core drilling in the Phosphoria formation has been done by mining companies interested in finding and developing phosphate-bearing beds amenable to stripping. The recovery of sludge; and enough core (usually 30 to 60 percent) to identify certain marker beds produced by current drilling practices meets both the primary requirement of mining companies in determining depth of overburden and their secondary need to determine the phosphate content of relatively thick minable units whose general composition and nature are already fairly well established.

Jan 1, 1949

By M. Clair Smith

The Sweetwater, Castro, Trinidad, New London, and Hilltop chromite properties are situated within an area 8 miles long and 1 mile wide between San Luis Obispo city and Morro Creek, San Luis Obiso County, Calif. Development work at this group of mines was a part of a long-range project by the Bureau of Mines to develop strategic mineral reserves in the United States in accordance with the Strategic Minerals Act of 1939. The junior author of this report participated in the preliminary examinations made in 1941 of the chromite deposits that later in the same year were the subject of more intensive investigation under the immediate supervision of the senior author. The ore occurs in lenses and kidneys in masses of dunite contained in large poridetite areas. Production has boon in the form of lump ore and concentrates from disseminated ore. Work by the Bureau of Miner included surveying, mapping, trenching, sampling, and assaying. It is summarized separately in the text under the name of each mine investigated. The report gives a brief history of the district, describer the concentrating plant of the Castro Associates, and gives detailed results on sampling and assays at the various proportion.

Jan 1, 1951

By Joseph E. Matta

The Bureau of Mines conducted a field study to investigate thin suppression of respirable dust by water sprays on a continuous-mining machine. Determining the importance of the top and bottom sprays for two types of spray nozzles was emphasized. Results showed, at a 90-pct confidence level, that (1) at least 70 pct of the dust was generated during the sump cut, even though nearly half of the coal was mined during the downshear operation, (2) the water sprays on the top of the boom had little effect in suppressing respirable dust, and (3) B.D. 5 spray nozzles mounted beneath the boom reduced dust at least 33 pet more than B.D. 5 sprays mounted on top of the boom. A single-cut technique was developed that gave good reproducibility for replicate cuts (coefficient of variation of 20 pct).

Jan 1, 1976

By M. R. Geer

The cleaning of fine coal, particularly for metallurgical use, is receiving greater attention. An increase in the proportion of fine coal in the run-of-mine product has been created by changes in mining practice, and a concur-rent deterioration in the quality of the fines has occurred because of more widespread full-seam mining. These two factors, augmented by the depletion of premium beds of metallurgical coal in some areas and the resulting shift to "dirtier" beds, are providing the impetus for adoption of improved cleaning techniques. For example, froth flotation, which has been used for years in a few preparation plants, now is gaining more rapidly in acceptance. Similarly, the dense-medium cyclone, which is used widely in Europe for making difficult separations, recently has been introduced to the United States. Regardless of the cleaning process employed, the finer sizes of coal can be treated with maximum effectiveness only when they are removed from the run-of-mine product and treated separately. No present process can treat the full range of sizes together with complete effectiveness. Flotation is applicable only to the coal finer than a top size ranging between 14-and 48-mesh, and cyclones require removal of all material finer than 0.5 to 0.3 mm. from the feed. Thus, the trend toward more-effective cleaning of the fine coal imposes the attendant problem of fine screening. Whereas in the past there was little need to screen finer than about l/4-in., present developments indicate that fine screening will become increasingly prevalent.

Jan 1, 1960

By J. E. Matta

The Bureau of Mines made laboratory absorption measurements on oil shale samples, which showed that the amount of methane absorbed is proportional to pressure and oil yield, and can be much larger than would be predicted based solely on porosity. Oil shale cores collected in the field were also measured for their gas content using the Bureau of Mines direct method. Cores taken from deep locations and far from outcrops yielded more gas than cores from shallower locations or at outcrops, when taking into account variations in oil yield, and all data indicate that oil shale mines that are both deep and far from an out-crop will emit low levels of methane gas.

Jan 1, 1977

The Mine Safety and Health Administration (MSHA) defines an independent contractor as any person, partnership, corporation, subsidiary of a corporation, firm, association or other organization that contracts to perform services or construction at a mine. Contractors that perform specific types of work are required to report the number of employees who work at coal mines and noncoal mines.

Jan 1, 2008

By P. C. Tully

The vapor pressure-temperature relationships for saturated pure liquid nitrogen are calculated by the Strobridge equation using a digital computer. This information is presented in two tables: first) in pressure increments of 0.1 psi from 1.8 to 492.9 psia) and second) in temperature increments of 0.1° from 63.15° to 126.26° K. These tables should facilitate the calibration of temperature-measuring devices over this temperature range.

Jan 1, 1967

By Steven J. Page

Since 1982 standard calibration materials recommended for respirable crystalline silica analysis by the Mine Safety and Health Administration (MSHA) P7 Infrared Method and the National Institute for Occupational Safety and Health (NIOSH) X-ray Diffraction (XRD) Analytical Method 7500 have undergone minor changes in size distribution. However, a critical assumption has been made that the crystalline silica in ambient mine atmosphere respirable dust samples has also remained essentially unchanged in particle size distribution. The objective of this work, therefore, is to compare recent particle size distributions of underground coal mine dust and the silica component of these dusts with estimated aerodynamic particle size distributions of calibration standard materials MIN-U-SIL 5, Berkeley 5, and SRM 1878 used by two crystalline silica analysis techniques. This work provides resolution to a previously reported discrepancy involving the proper sample dilution for the particle sizing method used. Dust impactor sampling data for various locations in 13 underground coal mines were collected between 1991 and 1998 and analyzed for the respirable mass median aerodynamic diameters. The data suggest that the MSHA P7 Method will underestimate the silica content of the sample by at most 8.5 % in the median size range of 0.9–3.6 µm and that it is unlikely one would obtain any significant error in the MSHA P7 Method analysis when the method uses Berkeley 5, MIN-U-SIL 5, or SRM 1878 as a calibration standard material. The results suggest that the NIOSH Analytical Method 7500 would be more appropriate for a dust sample that is representative of the total (no cyclone classifier) rather than the respirable airborne dust, particularly since the mass fraction in the size range below 4 µm is usually a small percentage of the total airborne dust mass. However, the NIOSH Analytical Method 7500 is likely to underestimate the silica content of an airborne respirable dust sample by only 5–10 %. The results of this study also suggest that any changes that may have occurred in the median respirable size of airborne coal mine dust are not significant enough to cause any appreciable error in the current methods used for respirable crystalline silica analysis.

Aug 3, 2005

By Allen D. Look

Underground fires often prove difficult to control , and a small fire can quickly grow into a large one , endangering life and causing large property damage . Even a small underground fire may produce enough noxious gases to cause suffocation ; therefore , every precaution should be taken to prevent and control such fires . It is ironic that mine fires should be caused when utilizing materials that are in themselves fire - resistant ; yet , cutting and welding of iron and steel are proving to be common causes of underground fires in metal mines . This paper includes 19 examples of underground fires of this nature , and undoubtedly this is only a fraction of the number of similar fires that have occurred in the last few years . This paper will review some metal - mine fires caused by cutting or welding and point out precautions to be taken to prevent other fires from this cause .

Apr 1, 1948

By Carl F. Wingquist

Electrical resistance heating to effect thermal fragmentation of semiconductive rock was examined by the Bureau of Mines. Tests were carried out on copper-bearing ores of the Nonesuch Shale Formation in the laboratory and in the the field at White Pine, Mich. Fieldwork included primary and secondary breakage tests. Heating tests on in situ rock failed to produce thermal dam-age to an extent considered useful; however, boulders up to 30 ft3 were effectively broken by the method. Power input to the test rock was taken from a 50-kV, 5-amp dc power supply.

Jan 1, 1976

The Bureau of Mines, in an effort to improve resource conservation, mine planning and development, is currently investigating the loading behavior of pillars in multiple-seam developments. The simultaneous mining of two or more coalbeds may cause instability between room-and-pillar operations resulting in an interaction known as pillar load transfer. Although pillars may be adequately designed for single-seam mining, the development of a second seam may complicate loading conditions in both operations. If pillars are not adequately designed to contend with this load transfer, failure of the mine structure may result. To improve multiple-seam development and pillar design, the Bureau studied the loading characteristics of pillars in three separate multiple-seam operations. In all three cases, instrumented pillars recorded increasing pressure after development of the second seam. Increases in the average pillar pressure ranged from 7 to 110 pct over predicted overburden loads. An analysis of pillar loading before and after second-seam mining indicates that the ratio of overburden to innerburden thickness is a critical factor influencing load transfer. Based on this relationship, safety factors for case study pillars are calculated and alternative design considerations are discussed.

Jan 1, 1988

By D. H. Platt

Data obtained from on-the-site observations have been compiled to describe the equipment and installation methods used for satisfactory suspension roof support in a large-diameter tunnel. Experimental roof bolting was undertaken from June 1950 until May 8, 1951, in the East Delaware tunnel, which is part of the Delaware aqueduct in Delaware and Sullivan Counties, N. Y. Revised suspension-roof-support plans and specifications were prepared during the spring of 1951 by the City of New York Board of Water Supply; these were approved by the State of New York Department of Labor April 13, 1951, and adopted by the City of New York Board of Water Supply on May 8, 1951.

Jan 1, 1952

By A. B. Pederson, G. E. Bartlett

As a part of our study of how coal mine dusts injure the lung we have studied the effects of dusts and dust-exposed pulmonary alveolar macrophages (PAMs) on the growth of lung fibroblasts (LF). Fibroblasts were cultured near confluence in low-serum medium, either alone or in the presence of dusts, dusts plus PAMs, dust leachates or superriatants of dust-exposed PAM cultures. We report here provisional conclusions, based on initial observations. Rat LF were relatively unresponsive to direct effects of dusts, showing weak stimulation in only a few cultures, and there was no evidence that dust-exposed rat PAMs had released any growth-regulatory products. In contrast, guinea pig cells were more responsive to the dusts. The pattern of responses was quite complex. Three of the dusts stimulated LF directly (with no mediation by PAMs). Two dusts were essentially inert when added directly to fibroblast cultures, either with or without PAMs, but their leachates were active: 867 leachate was inhibitory and RF leachate was stimulatory. Dust 1361, either directly in the cultures or as an aqueous leachate, was stimulatory, and it activated cocultured PAMs to stimulate LF growth; however, supernatant products of 1361-stimulated PAMs were inhibitory. Direct exposure to 1192 stimulated LF, but its leachate was inert; cocultured PAMs exposed to 1192 had weak stimulatory effects, but supernatants of 1192-exposed PAMs were mildly inhibitory. MP3-3 had effects similar to 1192, except that the cocultured, dust-exposed PAMs had no effect on growth. We conclude 1) that guinea pig lung cells are more responsive to dusts than are rat lung cells, 2) that dusts can influence growth of LF by four kinds of interaction (by direct dust-cell interaction, by release of soluble dust components into the culture medium, by activating P AMs to exert direct cell-cell interactions, and by activating P AMs to release growth regulatory products into the culture medium), 3) that each kind of interaction may be neutral, inhibitory or stimulatory, depending on the dust tested, 4) that four of the dusts tested were neutral, inhibitory or stimulatory, depending on the assay (the fifth <lust was either neutral or stimulatory), and 5) that the effects of soluble mediators (leachates or products of activated PAMs) frequently did not correspond with the direct dust-cell or PAM-fibroblast effects. These results suggest that the nature of the dust-lung interaction at the level of cells and molecules is exceedingly complex. These observations need to be confirmed and extended to determine what characteristics of the dusts determine the nature of the cellular responses, and to determine which patterns of responses are detrimental and which are beneficial in the overall health of the dust-exposed lung.

Mar 1, 1989

By L. C. IlsLey, E. J. Gleim, F. CRAVEN

Electrical apparatus and circuits began to be used in mines about 50 years ago. A search of the literature on mining reveals that in 1882, umping was being done by electricity in some aines of England. One account tells of a small electric locomotive being used in 1882 "to drive eight corves loaded with coal" in a mine near Dresden. In an account of his visit to some English mines, en American in 1892 mentions that he saw underground electric signals, lights, pumps, hoists, and one revolving- cutter-bar 19wall mining machine,. Among the carl electrical installa- tions in the United States was an electric locomotive in the Lykens Valley Coal Co. mine at Lykens Valley, Pa., in 1887. In 1889 the Sperry electric coal digger was being tried out. Tarce mining machines were placed in the Prospect mine, East Palestine, Ohio, in 1890. An electrical pumping plant was put in oneration during 1892 in the Woodward mine of the Delaware, Lacka- rahma & Western Railroad Co. Thus we Almost coincident with the proposed use of this new servant in under- ground workings, came the thought of making it safe in gassy mines. find an account of a design for a protected stationary electric mine lamp proposed by Edison in 1831. Enclosed-type motors rere developed in the United States and shiped to English collieries about 1903. From those early beginnings there has been continuous progress until to-day one finds hundreds of pieces of specially designed electrical apparatus distributed in American coal mines and in mines of nearly all important coal-producing countries. Along with introduction of this equipment grew the idea of the necessi- ty of government aid, in standardization. In most coal-mining countries to- day the governments either directly or indirectly have a considerable in- fluence in guiding the design of electrical equipment intended for use in Pasay mine

Jan 1, 1933

By Margaret R. Egan

The U.S. Bureau of Mines conducted experiments in the intermediate-scale fire tunnel to assess the influence of air velocity on the gas production and smoke characteristics during smoldering and flaming combustion of Pittsburgh seam coal and its impact on the detection of the combustion products. On-line determinations of mass and number of smoke particles, light transmission, and various gas concentrations were made. From these experimental values, generation rates, heat-release rates, production constants, particle sizes, obscuration rates, and optical densities were calculated. Ventilation has a direct effect on fire detection and development. The results indicate that, in general, increased air velocity lengthened the onset of smoke and flaming ignition, increased the fire intensity, but decreased the gas and smoke concentrations. Increased air velocity also lengthened the response times of all the fire sensors tested. Rapid and reliable detector response at this most crucial stage of fire development can increase the possibility that appropriate miner response (fire suppression tactics or evacuation) can be completed before toxic smoke spreads throughout the mine.

Jan 1, 2010

By R. A. Beall

Homogeneous zirconium-alloy ingots have been cast on a production basis by the consumable-electrode arc-melting process at the Northwest Electrodevelopment Experiment Station, Bureau of Mines, Albany, Oreg. This paper describes the various methods used to introduce alloying materials into the ingot and evaluates 1 each method by the degree of homogeneity of resulting ingots, as determined in tests on sections cut from the ingots. As many as 30 or more ingots, each 6 to 10 inches in diameter and weighing 300 to 500 pounds, were melted, using each method; and, as most of them subsequently were fabricated to strip 0.1 inch thick, the test results are considered to be representative of production practice. Ingot homogeneity has been considered more difficult to achieve in arc-melting practice than by methods where the molten metal is poured into molds and the addition can be stirred into the total mass of metal before casting. Owing to the unique requirements of consumable-electrode arc melting the addition can be made only to that part of the total mass of the ingot that is molten at one time. Observation of the flowlines in 500-pound ingots produced at Albany indicates that the molten pool has a maximum depth about equal to the ingot diameter. The weight of metal molten at one time is, therefore, not over 100 pounds. Characteristically, the arc-melting process is conducive to segregation, which can be overcome, at least partly, by adding the alloy constituents almost continuously during casting.

Jan 1, 1956

By H. Tomlinson

The development of the Sevier Valley Coal Co.&apos;s mine marks the opening of the Salina Canon coal district in Utah. The mine is favorably located with respect, to the existing markets of the West, and if the present estimates of the amount of workable coal in it are accurate it has many Important advantages in favor of its development. This mine is situated 18 miles east of the town of Salina, Sevier County, Utah, which at present is the nearest shipping point oh the Marysvale branch of the Denver & Rio Grande Western Railroad, and is about 152 miles south of Salt Lake City, which is the distributing center for much of the coal from the Carbon - Emery coal field and is the place from which nearly all Utah coal shipped to San Francisco and points on the northern Pacific coast has a common haul.

Jan 1, 1930