Search Documents

By J. P. Powell

The increased costs of exploration and drilling of new oil fields and the continued success of water flooding in nearly depleted oil fields have created a demand for information on the results obtained from individual projects. The Bureau of Mines has published several reports concerning water-flood activity in the Mid continent area and at the request of the industry has continued to collect and disseminate this information. This report was written in response to these requests. It describes in detail the water-flooding projects in Anderson, Franklin, Linn, and Miami Counties, Kans., and includes methods of water treating and the results obtained. The production histories of each county and many water-flood projects are shown graphically from the date of the first development. Maps of most of the major projects, showing their status as of January 1, 1953 are presented also. The practice of injecting water to stimulate oil production was legalized in Kansas in 1935, and the first water-flooding project authorized in this four-county area was initiated by the Texas Co. in December 1935 in Linn County, Forty-nine projects2/ initiated in the area to January 1953 are estimated to have recovered approximately 10 million barrels of oil that could not have been produced by methods used previously. About 7,900 productive acres had been, or are, flooded by these projects, and approximately 1.36 million barrels of water had been injected.

Jan 1, 1953

By Peter Swanson

One of the primary methods for analyzing roof stability in underground mines is the age-old method of “roof sounding” where a miner taps on the roof and listens for the hollow sound of loose blocks of rock. This paper looks at the feasibility of using noncontact laser-based vibration measurements to detect roof fall hazards with the ultimate vision of improving, expanding and automating procedures for mine roof inspection. Vibration measurements made on loose blocks of rock in underground mines are summarized and compared to estimates of fundamental resonance frequencies for rock slabs of the size responsible for highly hazardous “skin failures.” Both laser Doppler vibrometry and full-field interferometric methods are examined and are considered to be feasible methods for detecting anomalous vibrations in loose roof rocks. Results from simple laboratory experiments using laser vibrometry demonstrate some of the proposed application concepts. While considered a challenge to move these techniques from the laboratory to heavy industrial or outdoor environments, the potential for success in the current application is enhanced by the reduced requirements of qualitative analyses.

On 26 August 1971, the Bureau of Mines, through the Spokane Mining Research Center at Spokane, Washington, approved initiation of the evaluation of oscillatory energy toward enhancing flow of polymer into shale. The effort was an outgrowth of work performed under Bureau of Mines Contract H0210055, "Feasibility Study of Surface Impregnation equipment for the Chemical Stabilization of Coal Mine Structures," wherein feasibility of the impregnation concept was expressed and the detailed design of a machine for impregnation of coal mine roofs with polymer (under static pressure head) accomplished. Under these efforts, the potential enhance¬ment of polymer uptake into the shale thru superposition of oscillatory energy on the static impregnation pressure was suggested. A proposal for investigation of this phenomena entitled "Feasibility Study of the Application of Oscillatory Energy as an Aid to Afford Chemical Stabilization" was presented to the Bureau whereupon a three month program for initiation of investigation was approved.

Jan 1, 1972

By Lyman C. Hitchcock

The objective of this program was to determine the minimum luminance requirements for underground coal mining work from the working face to the first transfer point. The resulting data encompasses 114 visual tasks from conventional continuous and longwall mining methods representing the salient visual tasks found in the jobs listed. Cutter Operator Roof Bolter Face Drill Operator Airdox Operator Longwall Jackman Shuttle Car Operator Loader Operator Shot Fireman Continuous Miner Operator Longwall Head Conveyor Operator Longwall Tail Conveyor Operator

Jan 1, 1973

These proceedings consist of an overview of the in situ mining research currently being carried out by the Bureau of Mines. The following papers emphasize two general aspects of the in situ mining method: the environment and productivity. Both areas are extremely important, particularly because in situ leach mining is a relatively new mining method from a commercial point of view. Topics covered include the restoration of ground water, the selection of lixiviants, in situ mining of commodities other than uranium, in situ mining costs, the application of resistance measurements to in situ mining, an acid leach mining case history, and the use of branched boreholes for in situ mining. A bibliography of Bureau of Mines publications on in situ mining is appended.

Jan 1, 1981

By Jacob Schoder

This is one of a series of papers published by the Bureau of Mines on mining and milling methods and costs. The Tennessee-Schuylkill Corporation, Chloride, Ariz., mines and mills a lead-zinc ore containing gold, silver, and a small amount of copper. The mill products are lead and zinc concentrates that are shipped to smelters. The company was the second largest producer of lead and zinc in Arizona in 1937 and was seventh in gold production. Operations discussed are those being conducted at the mine in October 1938 and are representative of the complete operating period from 1936 to date.

Jan 1, 1939

By Zsuzsanna Zborovszky

Study of the energy transfer from an inductive circuit to the discharge under the conditions of the minimum discharge voltage being smaller than the source voltage. Analysis of the effect of the electrode separation speed on the duration and maximum power amplitude of the discharge. Recommendation for optimal electrode setting. Experimental data on the variation of maximum discharge power required for ignition as a function of volumetric gas content for methane-air and propane-air mixtures. Experimental determination of the ignition limit for discharges derived from a 24, 15, 10 and 6v inductive-resistive circuit in 8.3% methane-air mixture by using the PTB breakflash with Cd disc and W wires, and also with Cu disc and BeCu wires. Method for calculating ignition limits for other source voltages.

Jan 1, 1978

By Joan Weinberg

The real gross national product (GNP) expanded by 2.3% during the second quarter, down from the anomalous 4.4% growth rate in the previous 3 months. If the expansion continues through October, it will have lasted 5 yr and become the second longest in 40 yr.2 As in the first quarter, improvement in U.S. exports played a role in the continuing--albeit slow--growth. More than 2 yr of declines in the dollar relative to currencies of other industrial countries have contributed to a slight reduction in the trade deficit in real (volume) terms, as real net exports of goods and services rose $1.9 billion (table 1). Exports grew a strong 12.1% while imports, which had fallen the previous two quarters, rose 7.4%. Manufactured goods and petroleum products accounted for most of the second quarter import increase. The American Petroleum Institute estimates that the volume of crude oil and refined products imports in the first half of 1987 surpassed those in the same period last year by 7.5%, reflecting falling domestic production and higher than expected demand. Expenditure on durable goods--those that last at least 3 yr-by both consumers and producers also contributed to the second quarter expansion. Personal consumption of durable goods rose 9.0%, after having fallen the two previous quarters. Motor vehicle purchases accounted for most of the second quarter increase and the first quarter decrease. Sales of automobiles surged in the last quarter of 1986, as consumers rushed to capture the sales tax deduction that was eliminated on January 1. Sales fell in the first quarter of 1987, but have now moved closer to the trend line exhibited in the first three quarters of 1986. Automobiles accounted for half the 0.8% July gain in retail sales, and two-thirds of the 1.4% June gain. Producers durable equipment purchases also rose this quarter, accounting for the increase in nonresidential fixed investment.

Jan 1, 1987

By W. W. Stephens

As part of the Bureau of Mines program directed toward more effective utilization of the mineral resources of the United States, a number of processes for production of sponge iron have been investigated. The use of sponge iron as a raw material for production of steels and other ferrous alloys offers several possible advantages over the conventional pig-iron and scrap process, especially for utilization of the smeller, widely distributed iron-ore deposits of the western United States. Although considerable information has been made available on various processes for production of sponge iron, little information 118.6 been published heretofore on the problems and costs involved in melting the sponge iron for production of steel. The present Paper reports the results of tests conducted at the Bureau of Nines pilot plant at Redding, Calif. in which several different types of sponge iron Were used as charge material for production of steel in a 4-ton-capacity basic arc furnace.

Jan 1, 1949

By W. A. Grosh

The Piquette Mining and Milling Co, operates a zinc mine and concentrating mill in the Upper Mississippi Valley zinc-lead district near Tennyson, Wis. The principal ore mineral is zinc sulfide, which occurs in limestones and dolomites of the Decorah formation. Exploration in the district is by churn drilling from the surface. An adit at the base of the ore zone provides access to the mine. A room-and- pillar mining method with irregular pillars is used. Drilling is done with Jumbo-mounted drills. The broken ore is loaded by crawler-mounted front-end loaders into diesel-powered trucks for haulage direct to the mill.

Jan 1, 1959

By Ernest Ph. Hérivel

The mine and treatment plant of the Teziutlan, unit of the Mexican Corporation, S. A., are located at Aire Libre, in the District of Teziutlan, near the northwest edge of the State of Pueblo, Republic of Mexico. The property is leased from the Teziutlan Copper Co. The town of Teziutlan is the terminus of a branch railroad starting from Oriental Junction or the Mexico-Jalapa-Veracruz narrow-gage system of the National Railways of Mexico. A branch line 18 km in length from Teziutlan to Aire Libre belongs to the Teziutlan Copper Co. and is leased and operated in conjunction with the mine.

Jan 1, 1933

Provide the mining industry with a simple, accurate and readily available means of measuring the gas flow from pipe outlets such as gob holes Approach The Bureau of Mines conducted laboratory studies to establish correction or method factors for anemometers when used to measure gas flow from pipe outlets. Using the Anemometer Anemometers are used by the mining industry to make air velocity measurements in mine entries. Although the instrument has no appreciable influence on the airstream in mine entries, especially since the cross-sectional area of an entry is much larger than the cross-section of the anemometer, correction or method factors are used to correct the center line anemometer velocity to average velocity. This adjustment is made because the air velocity in a mine entry is highest in the center and lower at the sides. Anemometers can be used to measure gas flow from small diameter pipe outlets; however, since the instrument diameter is much larger than one-sixth of the pipe diameter, it will influence the air-stream from these small outlets. Resulting velocity measurements are erroneously high by as much as 30 percent. Method factors must be applied to such anemometer measurements taken at pipe outlets. Through a research investigation the Bureau of Mines established a set of method factors for center-line anemometer readings taken at the discharge end of 4-to 8-inch diameter pipes. These method factors were combined with method factors which were developed by the National Coal Board of Great Britain for 12-to 30-inch diameter pipes. The anemometer was mounted on the end of a short rod and held against the pipe for support except on the 4-inch pipe where the instrument was started and stopped remotely to prevent hand interference with the air-stream during measurements. Method factors were determined by comparing the anemometer measurements at the pipe outlet to the true average airflow which was simultaneously determined upstream by venturi measurements. Consequently, a method factor is nothing more than the ratio of the true velocity to an anemometer measurement.

Jan 1, 1987

By Dennis R. Dolinar, Gabriel S. Esterhuizen

In this National Institute for Occupational Safety and Health (NIOSH) investigation, numerical modeling is used to evaluate the degree the pillar strength is increased with a rectangular pillar over a square pillar. Three-dimensional models are developed with pillar sizes and geometries typical of underground limestone mines in the United States. Physical properties for the models are based on geotechnical surveys of nearly 30 underground limestone mines. To examine the effects of pillar length on pillar strength with the modeling, a parametric study was conducted where the pillar width was held constant while the length and height were varied resulting in width-to-height ratios ranging from 0.5 to 1.5 and width to length ratios ranging from 1 to 6. There are two aspects to pillar strength and failure. At relatively low stresses, pillars can fail as a result of geologic structure. At greater depths and sufficient extraction ratios, the pillars can also fail as a result of the vertical stresses exceeding the pillar strength. The effects of increasing pillar length regarding both strength aspects are presented in this study. Equations were developed for the increase in pillar strength with both height and length based on the model results. The results from these equations were compared to those from previously developed empirical equations for rectangular pillars. For the more slender limestone pillars with a width-to-height ratio below one, there is little increase in pillar strength for length-to-width ratios above 2 and almost no increase with length for a width-to-height ratio of 0.5. Only with the more squat pillars is there a significant improvement in strength with length. The gain in pillar strength with length for the pillars is explained by the change in the ratio of the area of the pillar affected by the ends to the area of the pillar. For the squattest pillar, the change in strength is also affected by an increase in pillar confinement along the central length of the pillar as the pillar transitions from a square to a long rectangular pillar. With geologic structure, added pillar length can significantly improve the pillar strength, depending on the strike of that structure with respect to the long pillar axis.

By G. L. Humphrey

Although thermodynamic data for ferrous oxide are among the most important in extractive metallurgy, adequate values have not been available until quite recently. The older data suffered not only from the usual experimental difficulties but especially from lack of the knowledge that ferrous oxide of stoichiometrical composition does not exist as a single, thermodynamically stable crystalline phase under any circumstances. This paper reports new experimental data on the heat of formation of ferrous oxide by two methods (combustion calorimetry and solution calorimetry), employing material of unequivocal composition. The results are compared with values obtained from data for the hydrogen reduction, carbon monoxide reduction, and disproportionation reactions of ferrous oxide, and a best value is selected. A table of heat and free energy of formation values of ferrous oxide to 2,000°K is given. These values are combined with available data for water, carbon monoxide, and carbon dioxide to obtain theoretical heats and free energies of reduction corresponding to the selected heat of formation. Hydrogen and carbon monoxide reduction equilibria are compared, and the differences in trend with temperature and the percentage utilization of the reductants are considered.

Jan 1, 1952

By L. R. Fisher

The purpose of this investigation was twofold: (1) To devise a rapid method for determining quantitatively the porphyrin-carboxylic acid content of a particular crude-oil porphyrin aggregate, and (2) to isolate porphyrins in the crystalline state from crude-oil porphyrin aggregates. The first purpose was accomplished by applying adsorption chromatography. In fulfillment of the second aim three different crystalline porphyries were isolated by methods which involved both adsorption chromatography and fractionation of benzene solutions with hydrochloric acid of varying strength. The three porphyrins had etio, rhodo-, and phyllo-type absorption spectra, respectively. INTRODUCTION Many samples of petroleum have, as interesting minor constituents, chemical compounds known as metalloporphyrins. Their presence in crude oil and other bituminous materials was first discovered by Treibs a quarter century ago. Much experimental work has been done on metalloporphyrins because of their importance to the petroleum industry. They have a deleterious effect on refining catalysts. The ash resulting from the burning of heavy fuel oil is very reactive, We to the presence of metallic constituents, particularly vanadium. In oil-fired gas turbines, the ash may build up on the blades, causing imbalance of the rotors and, in addition, severe corrosion. In industrial boilers, the ash residue is responsible for severe damage to boiler tubes and to the refractory brickwork (15).4 Through study of the chemical constitution of the various metalloporphyrins found in petroleum, much can be learned concerning the origin, migration, and history of crude oils.

Jan 1, 1961

By Thomas Brunsing

The program was carried out to develop deep kerfing and core breaking techniques to be incorporated into the design of a field prototype hard rock mining machine. The field machine is designed to mine non-abrasive bedded deposits up to 20,000 psi in uniaxial compressive strength. The mining technique involves cutting approximately 2 ft deep parallel kerfs spaced 2 ft apart in either a horizontal or vertical direction and subsequently breaking out the cores so defined. The prototype machine is intended for demonstration of the technique in a quarry or equivalent field environment. The program was aimed at minimizing the required kerf width, obtaining reliable breaking within that kerf width and determining cutter blade requirements necessary to achieve a mining rate of 20 ft3/min. Full scale breaking experiments and 1/2 scale kerfing experiments were employed to evaluate the system. High strength concrete test specimens were used to simulate the rock being cut and broken. The test results indicate the kerf/break technique can achieve the desired mining rate by utilizing two 7 ft diam blades to cut 2 in. wide by 24 in. deep kerfs. A lateral load applied at the base of the kerf (base shear) was selected at the core breaking technique to be employed by the full-scale prototype machine.

Jan 1, 1983

By H. R. Batchelder

Much information on oxygen production and the manufacture of synthetic liquid fuels has been published during the past several years. From time to tine the investment and operating cost of oxygen plants of various sizes has been estimated. Surveys have been made so that the various processes by which oxygen is produced commercially might be compared. The gas-making processes in which oxygen is employed, which wore used in Germany during the war, have been described in T.O.M. reels, and this information has been published. Descriptions of pilot-scale or proposed commercial plants for the production of synthesis gas or hydrogen and their conversion to synthetic liquid fuels also have been published. In general, each of these publications has dealt with a particular phase of the over-all problem. The present paper will discuss the relationship between these phases: The factors that affect oxygen manufacture and costs, the methods for the use of oxygen and for the production of synthetic liquid fuels, and, to some extent, the economic factors that must be considered.

Jan 1, 1951

By Karl E. Starch

This Bureau of Mines report is a background study of severance taxes on mineral production. The rates, bases, and other features of State severance tax legislation as of March 1978 are presented, as are the amounts of State severance tax collections for fiscal year 1977, Some statistical comparisons between severance tax collections, total State tax collections, and total value of mineral production in the States involved are presented to portray the relative importance of severance taxes both in State tax revenue systems and in mineral industry revenues. A general discussion of the purposes and principles of taxation, the unique nature of a mining enterprise, the various types of taxes imposed on mineral production, and the character and rationale of the severance tax and its impacts on mining firms sets the severance tax in perspective. A bibliography of materials on the severance tax is included.

Jan 1, 1979

By R. V. Ramani, W. Miola

"A relationship exists between the quartz contents in the underground coal nine airborne dust samples and those in the coal and host rocks that are mined [17, 18, 19] The prescribed method for quartz analysis in respirable airborne coal dust samples is the MSHA P-7 method. Accurate quartz analysis procedures are needed for bulk samples in order to predict the potential quartz content in airborne nine dust, which in turn will aid the design of quartz dust control procedures during mining. thereby reducing the airborne quartz dust in underground atmospheres. The requirements of this method are that the amount of quartz is the sample be less than 250ug, and the total sample weight less than 2,500 ug. Unlike with airborne dust samples, there are no limitations to the available mass of bulk samples. However, these are no standard procedures for the preparation of bulk samples for scanning or prescribed methods for quartz analysis. The NIOSH and MSHA methods are certified for roped* dust and the acceptance of these methods for bulk samples assumes that the bulk samples will be reduced to the conditions specified for respirable dust samples. An alternative method is X-ray diffraction, which provides higher average quartz values than those obtained from P-7 method for the same samples.An investigation was carried out to determine the optimal procedure for preparing the bulk samples for the IR and XRD analyses. In this paper, the investigations on the effects of calibration, particle sizes, matrix composition, interferrous, and behavior of the filter substances on IR, XRD and FTIR results are presented. The error introduced by the presence of kaolinite and a new sample asking procedure to reduce it are discussed. The problems experienced with conventional sample holders for scanning were eliminated with the design and development of a new hollow sample holder. Quantitative comparison of quartz determinations by IR, XRD and MR methods on coal, roof and floor rocks, and airborne dust samples are presented. The important factors affecting the results of quartz analysis methods are: 1) bulk sample preparation for obtaining representative and homogeneous analysis samples: 2) particle size distributions of the analysis samples and calibration standards; 3) qualitative matrix composition of the analysis sample; 4) matching calibration standards to analysis sample; 5) substrates for sample deposition during analysis sample preparation; 6) procedures for analysis sample mounting; 7) selection of proper portions of she response profile for insanity measurement; and 8) interferences of spurious phases with the critical analyses. The recommendations of this study are important to enable comparisons and interpretations of analysis and research results."

Nov 1, 1995

By Russell R. Trengrove

The Copper Canyon lead-zinc mine is in the Battle Mountain. District, Lander County, Nev. It was discovered in 1866 and mined for copper until 1935 and for copper and gold until l948, when the main production became lead-zinc ore. The rocks in the area are carboniferous (Pennsylvanian and Mississippian) sedimentaries that have been intruded by quartz monzonite of Mesozoic age. They have been intensely folded, faulted, and tilted. Lead-zinc ore occurs as sulfides disseminated along fractured zones in a conglomerate arid hornfels. Development was carried out by the Bureau of Mines in cooperation with the U. S. Geological Survey and comprised a study of the geology, making maps and. cross sections, and exploring the deposit by diamond drilling from underground. Eighteen holes were drilled, for a total of 2,594 feet. This report contains a brief history of the property and a description of mining methods and beneficiation of the ore, geology, ore deposits and drilling done by the Bureau of Mines. It also contains detailed analyses of the ore samples taken and logs of the holes drilled.

Jan 1, 1951