Search Documents

Studies of coal reserves have shown that the total augerable reserve base for the United States is estimated to be five billion tons under the current state of mining technology; the potential reserve base at 850-ft penetration is estimated at 20 billion tons. It is with the idea of improving coal recovery, a basic objective of Project Independence, that new concepts, such as modifications and improvements in current machines and development of ways to recover pillars left by current augering, are required. Unless recovery is improved, these potential reserves amount to lost coal.

Jan 1, 1975

By Stephen R. Iverson

Mineral deposits examined in and near the Raywood Flats RARE II area have low potential for development. The Mill Creek Mine (fig. 1), has produced about 14,000 tons (13,000 t) of marble, and another 5.5 million tons (5.0 million t) of marginal marble reserves suitable for lime, chemicals, and cement production are estimated to remain at this deposit. However, nearly all the marble is outside the study area. The deposit is marginal because alternate sources of marble are closer to markets. A tungsten occurrence in the marble is too small and low grade to be considered a resource. Ten tons (9.1 t) of uranium- and thorium-bearing material have been mined from a pegmatite dike at the St. Patrick Mine. However, this occurrence also is too small and low grade to be considered a resource. More than 400 lode and placer claims have been located in or near the study area. There are no current claims or mineral, oil and gas or geothermal leases.

Jan 1, 1983

By Benjamin C. Pollard

The location and production potential of a large block of strippable reserves in North Dakota were determined by using published data as a base and adding new drill hole data or other data contributed by companies that presently own or lease coal lands. Only beds exceeding 5 feet in thickness, under less than 120 feet of overburden, and in large blocks of 5 million tons or more were included in the estimates. All such reserves are in the Fort Union Formation of western North Dakota and are lignite in rank. Sixteen large blocks of reserves evaluated in this study are estimated to contain a total of 4.1 billion tons of strippable lignite.

Jan 1, 1972

This NIOSH Toolbox Training program contains 52 different modules designed to stimulate safety discussions among your employees. Each module is intended to be completed in roughly 10 or 15 minutes, so a Toolbox Training session can be conducted once a week for the entire year. Each session counts toward your employee’s 8-hour annual MSHA refresher training, thus saving an entire day of work.. The modules are used to refresh employees on the procedures, policies, and practices of working safely at a specific mine site and can easily be tailored to fit conditions and situations found on your property. Every module follows the same format, so that as the weeks pass, miners will start to approach every safety situation in the same way. A typical Toolbox Training session contains five basic steps that cover all the information in the module. 1. Identification of the hazard and discussions about the types of injuries typically associated with the hazard. 2. Discussions of some of the causes of the hazard. The MSHA example included with each module should be referenced. 3. After the hazard and accident has been explained and understood, discussions about best practices and tips for avoiding a similar accident. 4. Review of similar conditions or near misses from your mine site using the leading questions on the form to start a discussion. Specific examples of equipment or structures on the site that could lead to the same accident should be discussed. The blank space on the module is used to add your own remarks and questions to supplement the given information. 5. Miners fill out the training record on the back of the form with name, initials, and date of training session. The modules are designed to be kept in a standard three-ring binder and easily photocopied. This way, the same set of modules can be used for years to come. A blank form is included that can be used to create more Toolbox Training modules. The key component of Toolbox Training is to start a discussion among employees that will allow them to see the hazards around them every day and respond to these hazards in a safe and consistent manner. To start a discussion, ask questions that need more than a one-word response. Get the miners to talk about similar situations from their own experiences and give suggestions about how to fix the hazards around them. Toolbox Training is a quick and effective way to cover specific mining hazards, but it only works if miners are involved in the discussion.

Jan 1, 2004

By J. Ronald Lawter

The purpose of the work described in this report was to measure the effects of diesel engine emissions on the air quality of work areas in a coal mine. Concentration measurements of a number of diesel related air contaminants were made at the Martin County Coal Corporation Mine in Inez, Kentucky. Compounds measured included carbon dioxide, carbon monoxide, formaldehyde, nitric oxide, and nitrogen dioxide. In addition, concentrations of the two classes of odorous compound;, aromatic hydrocarbons, and oxygenates were obtained along, with aldehyde concentrations. Surveys were made of the mine by odor analysts to determine the perceived intensity of diesel-produced odors. It was found that the concentrations of the measured species were well below their Threshold Limit Values. Odor intensity levels in the moderate to strong range were observed in the mine.

Jan 1, 1977

By Richard J. Mainiero, James H. Rowland

When most people think of explosives transport they think of a hazardous operation. We all know that we aren’t allowed to transport explosives through tunnels and are discouraged from traveling through heavily populated areas. Popular opinion suggests that explosives transport is a very risky operation. The authors decided to look into this a little more thoroughly and found just the opposite to be true. While there have been some disastrous world-wide accidents involving the transport of industrial explosives, this is not the case in the U.S. Over the past 10 years, accidents related to the transport of explosives used in mining and construction have resulted in 5 major injuries, 11 minor injuries, and no fatalities. Explosives and ammonium nitrate (AN) transport outside the U.S. has not had such a good record; there have been 4 major explosives or AN transport accidents resulting in a total of more than 300 deaths. Most of these fatalities could have been prevented if the accident site had been evacuated once the explosive or AN cargo began burning. The safe history of explosives and AN transport in the U.S. is due to diligent efforts by government, labor, and industry. However, accidents will become more common and disastrous if we become complacent.

By S. M. Runke

"During the past three years the Bureau of Mines has carried on an extensive research program at the Rolla Laboratory for the beneficiation of low-grade Arkansas baixites by ore dressing methods. As a result of this study a 50-ton pilot mill was designed and constructed at Bauxite, Arkansas, by the Bureau to continue the investigation on a semi-commercial scale. The built both to reduce the experimental work to practice and to obtain operating data that cannot be determined by laboratory or small scaleTen samples of bauxitic material were mined and stockpiled at the plant site to ensure an ample supply of material for milling in the pilot plant. These samples were obtained from various bauxite deposits in Saline and Pulaski Counties, Arkansas. The deposits were selected as typical of a wide range of bauxitic material which would necessitate treatment under different conditions and by various concentration methods. All of the samples contained a higher silica content than permissible in Bayer-grade bauxite and several contained so much iron oxide that the available alumina content of the ore was mate¬rially lowered. From data obtained by milling operations on these ten samples, milling characterietics of most of the ores in the district should be predictable. This paper summarizes the results obtained in the laboratory testing of representative samples of each stock pile, and the results of small scale continuous testing of the composite sample of the ten stock piles in the gravity-flotation pilot plant at the Rolla Laboratory."

Aug 1, 1946

By John W. Colburn

A tractor-integrated version of an explosive ripping system was developed for mining application. This system utilizes diesel fuel and a tractor-mounted blower supplying 30 psig compressed air to a two-stage combustion chamber to produce a high pressure (600 psia) gas charge. The charge is rapidly released into the rock formation near the tip of the ripper. The system, mounted on a D9 tractor, was tested at several quarry and mining operations to investigate rock fracturing effectiveness. Although the results of comparative ripping passes conclusively demonstrated that the system increases rock fracture, performance of the system is strongly dependent on rock morphology and properties as well as basic performance of the tractor-ripper. The theory of conventional and explosive ripping modes is described and existing correlations of seismic velocity and ripper performance are shown to be in error.

Jan 1, 1977

By W. B. Berwald

The United States Bureau of lanes, in cooperation with the Natural Gas Department of the American Gas Association, has been studying actively for the past several years the problem of the flow of natural gas through high-pressure transmission lines. Numerous data on gas flow through pipe lines under many conditions of operation have been obtained by carefully conducted tests, and these data, together with all other available information, have been analyzed Carefully to secure practical facts for the use of operators in designing pipe lines and determining the effects of different operating conditions on pipe-line capacities. The first procedure in initiating this problem was to review, compile, and analyze all of the existing data on the flow of natural gas through pipe lines. Actual data applicable to pipe and operating conditions normally used in the transmission of natural gas were meager, and the several pipe line flow formulas developed by different investigators gave widely varying results when applied to problems of pipe-line design. Therefore, further experimental work under conditions comparable to those found in transmitting natural gas was essential before any definite recommendations could be made. The problem, as originally planned, included flow tests on pipe lines in operation, and in each test the measured delivery vas to be compared with the delivery calculated from several common pipe line flow formulas.

Jan 1, 1931

By E. P. Carman

1. DAVENPORT, S. J. Bibliography of Bureau of Mines Publications Dealing With Health and Safety in the Mineral and Allied Industries, 1910--46. Tech. Paper 705, 1948, 154 pp. 30 cents. 2. FJELDNER, A. C., FISHER, P. L., AND POLLOCK, M. B. Bibliography of Bureau of Mines Investigations of Coal and Its Products, 1940 to 1945. Tech. Paper 698, 1947, 53 pp. 15 cents. 3. GOOD, J. E., ABREU, ALVARO, AND FRASER, THOMAS. The Coal Industry of Brazil. Part 1. General Economy, Production, and Marketing. Tech. Paper 713, 1949, 38 pp. 20 cents.

Jan 1, 1954

By M. N. Rubin

This report summarizes the work performed under USBM contract J0100018. The purpose of this work was to document the currently available noise control techniques that can be incorporated into new coal preparation plants during the design stage. This was accomplished by reviewing the related experience of the contractor and subcontractor (Bolt Beranek and Newman Inc.), conducting an extensive literature search, visiting operating coal preparation plants, and contacting various equipment manufacturers. The treatments addressed include equipment substitution, changes in plant layout, and retrofit treatments for existing equipment.

Jan 1, 1982

By Stephen C. Tadolini, Steve Bessinger, James Pile, Christopher Mark

The San Juan Coal Mine, located near Farmington, New Mexico, supplies the San Juan Generating Station with more than 6 million tons of coal annually. To replace dwindling surface mine production, San Juan installed a longwall in 2002. The roof rock in much of the underground reserve consists of interbedded coals, carbonaceous shales, and mudstones. Roof support consists of fully-grouted roof bolts, both tensioned and non-tensioned, supplemented by modified cable trusses. Short-encapsulation pull tests conducted by San Juan’s geotechnical engineering department showed that some of the immediate roof layers provided variable bolt anchorage. To ensure that the roof bolts were obtaining the necessary anchorage, additional tests were conducted in a variety of locations. The results have been used to determine the optimum support design for different areas of the mine. Another series of tests evaluated the performance of several bolt and hole diameter combinations. The experience at San Juan Mine shows that short-encapsulation pull tests can provide the information necessary to improve ground control in variable roof conditions. It also illustrates how a pro-active geotechnical engineering program can be an essential component of a state of the art underground coal mine.

By Jr. Frost

Helium used as a tracer gas in petroleum reservoirs continues to show great promise as a new tool for the oil and gas industry, according to tests conducted jointly by the Bureau of Nines and The Pure Oil Co. in-the Cabin Creek field, Boone and Kanawha Counties, W. Va. Helium, when used as a, tracer gas, is mixed with natural gas being injected into a reservoir for secondary recovery of oil, recycling, pressure-maintenance, or other purposes. Three separate experimental helium tracer-gas tests were run in the Cabin Creek, W. Va., field, wherein helium was added as a tracer to the natural gas that was being injected into the oil-bearing Berea sandstone. The results obtained in each test permitted determining the direction and rate of travel of the injected gas, calculating the volume of injected gas in the gas produced at the various wells, and determining the nature of the transition from natural gas to injected gas during a gas-injection program. Data were obtained on the effects obtained from waves of injected gab containing 1 percent and containing 5 percent helium and from a wave of essentially pure helium injected into the formation.

Jan 1, 1950

By J. W. Thompson

OIL AND GAS AS MINERALS. Oil and gas within the ground are minerals and the fact that they have attributes not common to other minerals because of their fugitive nature or vagrant habit, and the disposition to percolate, and the possibility of their escape from beneath one part of the surface to another, does not remove them from the class of minerals. Texas Co. v. Daugherty (Texas), 176 Southwestern, 717, p. 719, May, 1915. OWNERSHIP OF TAILINGS-ABANDONMENT. A corporation engaged in milling- and the reduction of ores deposited the tailings therefrom upon a portion of its own land lying in a gulch through which water flows at times in great volumes and with great force' and notwithstanding all reasonable efforts by dams and otherwise to retain its tailings, the tailings eventually were forced upon the lands of an adjoining owner; these tailings were valuable and their retreatment, intended by the mill owner, profitable; and the fact that the tailings were so washed down upon the lands of the adjoining owner and permitted to accumulate and remain for some considerable time is not sufficient to show an abandonment on the part of the owner of the tailings, where it is clear that the owner had no intention of so doing, but on the contrary, always intended to conserve and retreat the tailings.

Jan 1, 1916

By A. E. Petersen

To reduce U.S. dependence on imports of titanium, the U.S. Bureau of Mines has investigated the recovery of titanium from perovskite (CaTi03). Domestic perovskite deposits represent a significant, but untapped, titanium resource. An acid sulfation method was developed that will extract about 97 pct of the titanium and the columbium and 70 to 90 pct of the rare-earth byproducts from perovskite concentrates. A flow-sheet for recovering titanium as pigment-grade titanium dioxide (Ti02) is discussed. Test work performed in developing each unit operation is described. The first three unit operations have been demonstrated using laboratory-scale continuous methods of operation: acid sulfation of perovskite concentrates, leaching sulfation residue to dissolve metal values, and precipitation of titanium oxysulfate monohydrate (TiOS04?HP) from the resulting leach flltrate. Batch testing of other unit operations was performed: TiOS04?H20 redissolution and iron reduction, precipitation of Ti02 by hydrolysis, and regenerating recoverable acid with rare-earth byproduct recovery. Cost evaluation results are provided, indicating that processing perovskite concentrates by acid sulfation may be an economically viable means of producing Ti02.

Jan 1, 2010

By M. M. Tilman

In a Bureau of Mines investigation to develop lead alloys with improved tensile strength and creep resistance, lead-base alloys containing cadmium and antimony in nominal 1-to-1 atomic ratios were melted in air, cast, and rolled into sheet to 90 percent reduction at temperatures varying from room temperature to 175° C. Tensile testing at room temperature and stress-rupture testing at 900±3° F were conducted on the as-rolled alloys. The best tensile properties were observed in an alloy of Pb-4.2 wt pct Cd-4.5 wt pct Sb which exhibited an average tensile strength of 7,270 psi with 36 percent elongation in 2 inches. An alloy of Pb-5.5 wt pct Cd-6.0 wt pct Sb had 100-hour stress-rupture values of approximately 2,100 psi and 1,000-hour values of approximately 1,700 psi.

Jan 1, 1969

By C. C. Stevenson, Thomas Varley, E. P. Barrett, ROBERT H. BRADFORD

The art of treating ores by the chloride volatilization process is still in the experimental stage. The process has not been sufficiently developed along metallurgical lines to warrant a definite statement as to the exact place it will occupy in the industry. The basic theory of the process has received the attention of prominent metallurgists for 20 years, and considerable research and experimental work have been carried on. Much of the experimental work done has never been published; if the accumulated results were made known, they would greatly aid,. the further development of the process. This bulletin aim~ to bring the salient features of the process to the attention of metallurgists for the purpose of furnishing information to and receiving comments from interested parties with the ultimate hope that the process will be a commercial success. If commercially utilized, the process will fill a long-felt want in metallurgy, especially in the treatment of oxidized and semioxidized or" carbonate" ores of copper, lead, and silver. Such ores are difficult to treat by gravity concentration or by flotation: in the former their tendency to slime upon crushing and their being of lower specific gravity than the sulphide minerals cause serious losses; in the latter much has been done in sulphidizing oxidized ores and subsequently recovering the artificial sulphides by flotation. Difficulties in proper sulphidizing and the low recoveries obtained have not balanced the cost of the treatment in many plants and in very few has it proved successful. Evidently there is a big void to fill in the treatment of these ores. No radical changes in present methods are forecast, but it is obvious that chloride volatilization can have a distinct place as a method of treatment for ores that are not readily amenable to present methods. In many plants it might replace concentration methods, especially where part of the mineral content in the ores exists in forms other than sulphides.

Jan 1, 1923

By Richard L. Fowler

Study and development of sensing techniques and sensors were performed to aid shuttle car drivers in detecting obstacles and in guiding the car along the face haulage route. Microwave, acoustic, and optical sensing techniques were considered as part of the feasibility study for obstacle detection. Various guidance techniques, including wire-following and rib-ranging were investigated. Active optical sensing was selected for obstacle detection to obtain the beam coverage and sharp angular cutoff characteristics required within the packaging limitations defined by the shuttle car configuration. Rib-ranging guidance was selected to achieve a completely self-contained shuttle car system which responds to the existing mine geometry without need for wires, stripes, or other path defining devices. Extensive hybrid computer simulation runs were performed to evaluate various guidance techniques during the feasibility study. Subsequent simulation runs were performed to establish parameter values for the rib-ranging guidance system. The obstacle detection and guidance system was designed, fabricated and installed on a standard shuttle car. The system satisfied all applicable permissibility requirements of Schedule 2G. An experimental permit was issued to Bendix for operation in an underground coal mine. System evaluation tests were performed first above ground at the Bendix Research Laboratories. The simulation model was validated by these runs. Final testing was performed underground in an operating mine with an experienced shuttle car driver. All sensors successfully demonstrated the predicted performance capability during underground face haulage tests. Dust did not impair system performance and lens cleaning was not required during working shifts. Further development is required to achieve the desired obstacle detection performance. Closed loop steering control with manual override is recommended for the lateral guidance system. The guidance system should be an invaluable aid to low-coal shuttle car drivers where continuous mining machines are utilized.

Jan 1, 1973

By William E. Souder

Behavioral accidents are a particular type of accident. They are caused by inappropriate individual behaviors and faulty reactions. Catastrophe theory is a means for mathematically modeling the dynamic processes that underlie behavioral accidents. Based on a comprehensive data base of mining accidents, a computerized catastrophe model has been developed by the Bureau of Mines. This model systematically links individual psychological, group behavioral, and mine environmental variables with other accident causing factors. It answers several longstanding questions about why some normally safe behaving persons may spontaneously engage in unsafe acts that have high risks of serious injury. Field tests with the model indicate that it has three important uses: It can be used as an effective training aid for increasing employee safety consciousness; it can be used as a management laboratory for testing decision alternatives and policies; and it can be used to help design the most effective work teams.

By Larry L. Wischhoefer

The Automated Breathing Metabolic Simulator (ABMS) is a versatile machine capable of performing almost any physiologically appropriate respiratory simulation. The first ABMS was delivered to the Bureau of Mines by IBM in 1973. Since then efforts have been made to refine the systems and components which make up the ABMS including the Breathing Simulator Module (BSM), Gas Analysis Module (GAM), and Supervisory Controller (SC)-each of which are also capable of stand-alone operation. Since September 1980, Reimers Consultants has been testing and modifying the ABMS and its components in order to improve the equipment and to develop simulation criteria and parameters. Changes have been made to the Phase I Design Plan and Performance Specifications; future improvements based on current experience are recommended; and test results of full scale testing conducted by Reimers Consultants in November 1983 on several types of breathing apparatus are reported and illustrated.

Jan 1, 1984