Search Documents

By G. B. Sonneman

This final report summarizes the work done by The Bendix Corporation, Environmental Science Division, under contract to the Bureau of Mines to design, develop and test two improved systems for remote sampling the air at the working face of a coal mine in conjunction with approved portable methane detectors and machine-mounted methane monitors respectively. The work was started in May 1973 with preliminary design studies and was completed in May 1975. Five portable and two machine-mounted sampling systems were delivered. Contract "add-on" requirements for (1) modification of the machine-mounted system to accommodate a flame safety lamp and (2) a study of sensor response time improvement for the machine-mounted system were also completed.

Jan 1, 1975

By Curtis H. Elder

In studies conducted by the Bureau of Mines, two test areas were hydraulically stimulated and exposed by mining: One in the Pittsburgh coalbed at the Vesta No. 5 mine, Washington County, Pa.; and one in the Illinois No. 6 coalbed at the Inland mine, Jefferson County, Ill. Induced fractures were contained totally within the coalbed with no adverse effect on the stability of associated rock strata. Induced fractures were vertical and were propagated normal to the direction of least residual tectonic stress. Gas production was increased fivefold to twentyfold by hydraulic stimulation.

Jan 1, 1977

By E. R. Maize

[he scconG rcport of :his st?rI.org 8cdt with o3servatioi:s of conver- gence of roof an4 floor at t!x*re: ?.cc.-.tioris iri til~ ClVucible mine of kke Cru- cib1.o Fuel Co. Data on sl:'ociacnce ?.rd Lztcrcl mwe:~cnt cf the surface were .:lven for two of these areas, a-12 it was mentioned that ~lr~~ilar data were being obtained on a ?art of Pe:sc:rlvtzr.ia Fii~l?trr.y FE:, ~i!lic;l pcser: over the third area. 'I'hie hichw~ :LEO FasseE over t!lc ITenncoli::. :.line of the Bnckeye Coal Co. 9 milcs to ';he so-lth, cnd at P. l~tcr C'..att: ~.nr?r.,cc?r:cntS *.rere mnd.e to make similar observati on3 there. This y: pr mrnmri:.c n Czto obtnino? at those two locetionn,]

Jan 1, 1941

By W. B. Berwald

The United States Bureau of Mines, in cooperation with the Natural Gas Department of the American Gras association, has been studying actively for the past several years the problem of the flow of natural gas through high-pressure transmission lines. Numerous data on gas flow through pipe lines under many conditions of operation have been obtained by carefully conducted tests, and these data, together with all other available information, have been analyzed carefully to secure practical facts for the use of operators in designing pipe lines and determining the effects of different operating conditions on pipe-line capacities. The first procedure in initiating; this problem was to review, compile, and analyze all of the existing data on the flow of natural gas through pipe lines. Actual data applicable to pipe and operating conditions normally used in the transmission of natural gas were meager, and the several pipe line flow formulas developed by different investigators gave widely varying; results when applied to problems of pipe-line design. Therefore, further experimental work under conditions comparable to those found in transmitting natural gas was essential before any definite recommendations could be made.

Jan 1, 1931

By Donlad B. Lindsay

This report describes a field-test program to determine the effectiveness of a polymeric wall sealant to reduce the excape of naturally occurring radio-active gas radon from the walls of an underground uranium mine into the ventilation air. A 75-foot-long, dead-end drift with a surface area of about 6,000 ft2 was used as the test site in which the average natural radon flux from the normally dry rock was 16 fCi/cm2-s. The effect on radon emanation of wetting the walls with water to a depth of 3 inches was tested, after which the rock was completely covered with a coating of dry-mix concrete to provide a base for the sealant, an acrylic latex. Sealant was applied in two coats to about 0.25 mm thick. An overall reduction of average radon flux of about 75 pct was achieved. Radon production and other environmental values were measured continuously and automatically by a Bureau of Mines data acquisition system. A commercial microcomputer was programed to convert raw data to engineering units and to perform other useful operations while recording all data on magnetic diskettes. Direct measurements of radon flux from the rock surface were made by a charcoal adsorption technique.

Jan 1, 1981

By Thomas J. Peters

In 1984, at the request of the Bureau of Land Management, the Bureau of Mines studied 7,000 acres of the 9,240-acre Little Blitzen Gorge Wilderness Study Area in Harney County, OR, to evaluate its mineral resources. The study area is dominated by a 1,500-ft-deep canyon that was carved by Pleistocene glaciers in gently westward-dipping homoclinal flows of Miocene Steens Basalt. The Bureau reviewed pertinent literature and county mining records During the field investigations, 18 rock samples were collected from basalt dikes, breccia, fractured or porphyritic flows, and 20 alluvial samples from gravel accumulations. Mercury anomalies from sampling by the Oregon Department of Geology and Mineral Industries could not be verified. The mercury might have originated -From the Pike Creek Formation, a known mercury-producing unit that may extend into the study area beneath the Steens Basalt. Any epithermal deposit at depth would be expensive to explore and develop.

Jan 1, 1986

By Thomas G. Chapman

The four major steps in the production of marketable copper are mining, concentrating, smelting, and refining. In a few cases, however, leaching takes the place of concentrating, smelting, and refining, and in others ores are smelted without being concentrated. Copper ores have been milled since the early days of mining in the United States. Except in the Michigan district, most copper ores went direct to the smelter until the so-called porphyry mines were developed. At present, although considerable leaching and direct-smelting ores are produced, the bulk of the copper ore mined is concentrated. Improved methods of concentration have kept pace with the increased tonnages of ores milled.

Jan 1, 1936

By J. R. Thoenen

Occurrences of titanium, zircon, and other heavy minerals are widespread in Florida. Deposits concentrated as "heavy sands" by wave and wind action have been mined an or near Atlantic coastal beaches since 1916. An important inland concentration at Trail Ridge; .believed, to have formed along an ancient share line, was disclosed by preliminary investigations (1947) by the Bureau of Mines. This report describes investigations to determine the extent and grade of "heavy-sand" concentrations in other inland stabilized dune areas in the central and northeastern parts of the peninsular region of the State (fig. 1). Portions of the central highlands south of Trail Ridge and terraces and dunes in the coastal lowlands region, east and northeast of the ridge were investigated. Holes were drilled in 10 areas (see table 1 and fig. 2) along State and County roads and on private property. They were spaced 250 to 2,000 feet. apart to obtain a cross-sectional picture of "heavy-sand" content in the dune areas. These sections were generally placed in east-west directions normal to the general trend Of the peninsula to intercept one or more of the ancient shore lines in the various areas (figs. 3 to 13, incl.). A total of 433 drive piped and 333 jet holes were drilled, and 7,293 bulk and core samples were taken. Intermediate holes were placed at closer intervals when field analysis indicated 1 percent or more of heavy minerals present. All of the holes drilled and the analysis of samples that contain 1 percent or more of heavy minerals are listed in table 2. Profiles (figs. 14 to 20, inclusive) show the more favorable concentrations, which are irregular in outline and erratic in mineral content. The highest concentrations averaged 1.0 to more than 2.0 percent heavy-mineral content, but a few individual hole samples exceeded 3.0 percent in grade.

Jan 1, 1949

By N. L. Wimmler

The chromite deposits along the Stillwater complex in Stillwater and Sweetgrass Counties, Mont., have at various times been studied and reported on by the Federal Geological Survey, the Montana Bureau of Mines and Geology, other Government agencies, and private interests, Several of the deposits were explored to a mall extent by the owners during the World War of 1914-17, but no production resulted. The importance of these deposits and the urgent necessity of developing large domestic sources of chromite were realized shortly before the beginning of the recent World War. These deposits were therefore investigated and developed by Government agencies and., as a result, now afford the largest known reserves of chromium in the United States. In 1939, under the authority of the Strategic Minerals Act, the Bureau of Mines and the Geological Survey made preliminary investigations of these deposits. As a result, the Bureau of Mines conducted an extensive program of trenching, diamond core drilling, and sampling. This work was begun in August 1939 and continued to April 1943. The Bureau of Mines also performed numerous metallurgical tests on the beneficiation of the chromite ores and concentrates and for the production of chromium metal there from. Research continues as a means toward utilizing these ores.

Jan 1, 1948

By Corate L. Brierley

Low-grade porphyry copper ores containing chalcopyrite as the primary mineral was leached by two strains of acidophilic, thermophilic microbes belonging to the genus Sulfolobus. Leach tests were conducted in glass columns heated to 60-70° C. Pinto Valley and San Manuel ores sized to -1/2 inch + 50 mesh were effectively leached by the thermophilic organisms, but pinto Valley and Cyprus Bagdad ores sized to -2 inch + 1/2 inch resisted leaching. Aeration did not contribute measurably to bacterial copper extraction, since two columns, one inoculated and one sterilized, having a rest/ leach cycle without recurrent aeration exhibited copper extraction patterns similar to those of the aerated columns. Distilled water can be substituted for 9K medium without diminishing copper extraction. Decreasing the pH of the leachate to about 1.8 enhanced the extraction of copper from pinto Valley ore with the thermophilic microbes. Thiobacillus ferrooxidans was found to be relatively ineffective at copper extraction from pinto Valley ore. Of eleven solvent extraction reagents tested, Adogen 364 and Warsol at concentrations of 0.1% and 0.012 were inhibitory to oxygen uptake by the two Sulfolobus strains. Di-2-ethyhexyl phosphoric acid at concentrations of 0.1%, 0.01% and 0.001% were totally inhibitory to the respiration of both organisms.

Jan 1, 1979

By Jeffrey S. Newman

This report establishes a methodology for the evaluation of gas detection devices and is the result of a critical investigation into the basic principles defining gas detector performance. A scheme is presented to evaluate the performance of a test sample of gas detectors based on the detector type and intended application. Test procedures, worksheets, test apparatus, glossary and statistical methods for handling test data arc given. In addition, evaluation standards and test parameters are identified. It is intended that this report serve as a comprehensive framework for the eventual certification of all gas detectors for mine applications. A plan is proposed and recommended for the quantification and implementation of evaluation standards for gas detection device certification.

Jan 1, 1980

By Herbert H. Einstein

The thrust of research reported in Part I was to collect in-situ data from exploration programs and the published literature, and to empirically establish distributional patterns for these variables. Since discontinui¬ties in a rock mass govern to a large extent its engineering properties and thus the performance of any slope in the mass, work has been devoted to determining the appropriate distributional forms for attitude spacing and length of discontinuities and to distributional properties of resis¬tance and deformability parameters. The conclusion from these analyses is that trace lengths are logNormally distributed and that joint spacing is Exponentially distributed, regardless of orientation of the sampling line, and regardless of whether each joint set is considered separately or not. Joint orientation (attitude) data representing 22 individual joint sets from eight sites (a total or approximately 20,000 joints), do nor strongly support any of the commonly used distributions as broadly applicable in practice. The autocorrelation )f geometric joint properties is also examined. However, no significant spatial correlation could be found even after extensive data manipulation. The investigation of resistance and deformability parameters starts with a review of mechanisms and models that are used to represent them. Review and statistical evaluation of approxi¬mately 2,000 discontinuity shear tests has shown that good statistical estimates for use in reliability analyses can be obtained for friction angles.

Jan 1, 1979

By Samuel P. Harteis

Many mining operations rely on retention bulkheads to provide a barrier between impounded water and active mine workings. However, bulkhead failures can cause catastrophic flooding that puts the underground workforce at risk. Underground observations and evaluations of existing bulkheads indicate that a systems approach is required when building an underground water or slurry retention system. In addition to engineering the bulkhead, the designer must ensure the quality control of materials and workmanship of the bulkhead, the reaction of the mine strata when exposed to water under pressure, and methods to monitor the performance of the retention system. Researchers from the National Institute for Occupational Safety and Health (NIOSH), with the assistance of the Mine Safety and Health Administration (MSHA), conducted an extensive review of bulkhead permits submitted to the MSHA Technical Support office in Bruceton, PA. In addition, the researchers visited accessible bulkhead installations at undeground mining operations to gather information related to construction practices, maintenance issues, and monitoring and emergency response procedures. Several key items were identified that must be considered when permitting the installation of an underground fluid retention system.

Jan 1, 2008

By A. F. Colombo

Bench-scale research was undertaken to determine if adding ammonia to cyanide leaching solutions would enhance the extraction of copper from an argillaceous Michigan copper ore. Two leaching techniques, (1) rolling using a tumbling bottle and (2) aerating using a modified Buchner funnel, and variations in pulp temperature; were employed in evaluating the effect of ammonia concentration on copper extraction. Under these experimental conditions, the extraction of copper was shown to be independent of ammonia concentration and entirely dependent on cyanide concentration.

Jan 1, 1968

By Richard A. Winters

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied 49,875 acres of the 54,833-acre Big Jacks Creek Wilderness Study Area (ID-111-7C) in order to evaluate the mineral resources. The study area is located in Owyhee County, ID, about 15 miles southwest from Bruneau, ID. No mining districts are in the study area, but part of one placer claim, located in 1924, extended into it. The northern portion of the area was covered by oil and gas lease applications; all were cancelled prior to 1985. No economic concentrations of minerals were found in the study area. INTRODUCTION This report describes the USBM (U.S. Bureau of Mines) portion of a cooperative study with the USGS (U.S. Geological Survey) to evaluate mineral resources and potential of the Big Jacks Creek study area at the request of the BLM (U.S. Bureau of Land Management). The USBM examines individual mines, prospects, claims, and mineralized zones, and evaluates identified mineral and energy resources. The USGS evaluates potential for undiscovered resources based on areal geological, geochemical, and geophysical surveys. Results of the investigations will be used to help determine the suitability of the study area for inclusion into the National Wilderness Preservation System. Although the immediate goal of this and other USBM mineral surveys is to provide data for the President, Congress, government agencies, and the public for land-use decisions, the long-term objective is to ensure the Nation has an adequate and dependable supply of minerals at a reasonable cost.

Jan 1, 1986

By Peter G. Groer

The commonly used exact methods (1-2) to determine the WL measure the total a activity or the total number of a counts during three preselected time periods. Due to the half-lives involved (TRaB = 26.8 min, TRaC = 19.7) I these methods take 3S minutes to complete the a activity Ra measurements. Methods using the total a counts, obtained at times less than about one RaB half-life after the end of sampling run into statistical 214 problems. These methods are almost blind to RaB (Pb214) as a consequence of its relatively long half period (see above) and the fact that RaB is a ß emitter. The way out of this dilema is to measure RaB directly through its ß activity. Since RaB's daughter Rae (Bi214) is also a ß emitter, the two f3 spectra have to be separated to obtain RaB alone. How this is accomplished 1s described in subsequent sections describing the theory of the IWLM and its calibration. 2.0 THEORY The IWLM samples air for two minutes and counts this airs ample for two minutes starting 3 sec after the end of the sampling period. The instrument has three channels. The lower a channel, the upper a channel, and one ß channel. The total RaA counts observed are accumulated in the lower a channel, the total RaC? counts are stored in the upper a channel. The total ß counts from RaB and RaC are recorded in the ß channel. These three quantities are functions of NA, NB, and NC, the unknown concentrations

Jan 1, 1975

By W. R. Byrnes

This project was initiated on October 1, 1980 and will be completed on December 31, 1983. The project was Initially approved and funded by the Office of Surface Mining and subsequently was moved to the jurisdiction of the Bureau of Mines. It was administered through the Indiana Mining and Mineral Resources Research Institute. The research was done to assess reforestation success and ultimate productivity for areas reclaimed under the Surface Mining Control and Reclamation Act of 1977 (P.L. 95-87). The Permanent Regulatory Program for implementation of P.L. 95-87 Includes provisions for revegetation that require seeding of ground cover plants to control erosion until permanent vegetation such as tree species Is established, and restoration of mined land to its original or better productivity. Much of the land to be surface-mined presently supports forest cover and it is anticipated that reconstructed minesoils will exhibit high productive potential for hardwood tree species. Hence, information was needed on compatibility of ground cover and tree seedlings when established concurrently as well as on revegetation success under postmining versus premining conditions.

Jan 1, 1983

By Richard H. Bares

The general or macroclimate of the study sites in western North Dakota is characterized by rapid and sometimes extreme daily and day-to-day temperature fluctuations, rainfall patterns which are erratic in spatial and temporal distribution and intensity, generally low relative humidity, plentiful sunshine, nearly continuous air movement, and a relatively short frost-free period. Of particular relevance to plant growth and productivity is the mosaic of microclimates: these microclimates are affected by landform (convex and concave surfaces); exposure; slope angle, length and aspect; soil color, texture and surface cover (litter), and vegetation cover. The most critical plant growth governing factor in this region is available water. It is determined principally by water input (precipitation) and water loss (evapotranspiration) which is increased by high temperatures, wind, and poor litter and vegetation cover. While spring and fall precipitation is generally gentle and soil-soaking summer rains frequently come in the form of intensive, soil-washing, localized convective thunderstorms of short duration. Due to the convective nature of these storms, summer rainfall is particularly affected by regional topography; southwest slopes and crests often receive more rainfall since these storms usually move in a northeasterly direction. The water loss due to runoff and consequent soil erosion arc major problems resulting from such "cloudbursts". Previous fall precipitation (September - October) when added to current seasonal precipitation (March - August) was found to be significantly correlated (r-.93) with plant production. Winter precipitation (snowfall) is relatively light as the prevailing weather is dominated by dry polar air masses from the north. The nearly continuous wind is responsible for removing snow from open exposures and depositing it in depressions and windbreaks. Although the winter precipitation is not a large component of the total annual precipitation, conservation of that which does occur would contribute to plant production during the following growing season. Generally clear skies over the region facilitate receipt of abundant sunshine at the earth's surface. While good for early season soil warming and plant photosynthesis, this abundant sunshine coupled with long days and nearly continuous wind is responsible for evapotranspiration exceeding precipitation by an average of six inches between June' and September. On a local (micro) scale, the water deficit is most severe on the southern exposures which receive the most direct (most effective) solar radiation and therefore are warmer than other exposures. On a broader scale, it was found that ambient temperature extremes were slightly but significantly greater in the town of Beulah in the Knife River Valley than at the upland test sites, This may have been due to the difference in topography and/or the "urban heat island" effect. It is known that air temperatures in large cities may be 2° to 4°C higher than that of the surrounding countryside. It is also well known that basins, depressions or valleys are sinks for cold air masses and are often subject to frosts not occurring on adjacent upland sites.

Jan 1, 1982

By N. E. Hanna

The current list of permissible explosives includes 124 different brands. Fifteen of these are gelatinous, and the rest are the more commonly used granular ammonium nitrate type. Their rates of detonation range from 1,300 to 5,600 meters per second, and the weights of 1-1/4 x 8-inch cartridges range from 86 to 244 grams. The list of permissible blasting devices includes 1 Cobra, 2 Hydrox, and 9 Cardox models. All of these devices are based on discharge of high-pressure gas from a pressurized shell in a shothole. INTRODUCTION To be approved for use in underground coal mines in the United States, explosives and blasting devices must pass certain schedule tests prescribed by the Bureau of Mines. The explosives listed here were tested under Schedule 1-G,3 which has since been replaced by Schedule 1-H;4 the blasting devices were tested under Schedule 26A.5

Jan 1, 1962

By J. J. de Barbadillo

This report describes a process for recovering chromium and other metals from superalloy scrap. Part I contains the results of laboratory scale experiments which were conducted to test a complex flowsheet utilizing a wide range of extractive metallurgical operations. The novel basis for the process is the formation of a sulfide matte in which chromium is concentrated in a discrete chromium sulfide phase. Mineral processing and hydrometallugical procedures are used to separate chromium sulfide from the other matte constituents. The products of the process are a chromium-nickel alloy suitable for reuse in the superalloy industry, electrolytic nickel, electrolytic cobalt, and an iron-molybdenum residue. Recovery of the principal elements contained in the scrap are chromium(Cr)-93 percent, nickel(Ni)-99 percent, cobalt(Co)-96 percent, molybdenum(Mo)-92 percent. Part II encompasses a preliminary engineering design of a pilot plant capable of treating 100 pounds(lb) of superalloy scrap per hour. Also included is an economic analysis of the operation of the pilot plant.

Jan 1, 1980