Search Documents

The objective of this study was two-fold: 1. To perform a world literature search pertinent to the analysis, selection and design of hoisting systems and their components and to codify the search into a literature compendium. The search resulted in a technical data file of over 1500 hard copy items. The compendium index was also suitable for establishing a comprehensive computer-loaded data base on the subject. 2. To develop a comprehensive system of guidelines to cover salient aspects of analysis, selection and design of electrical, mechanical and structural components of a hoisting system with a view to establish parameters for maximum safety and efficiency of operation, installation and revision of the system. 3. (a) In-shaft equipment design and specification criteria are considered as they influence guideline preparation. (b) A comprehensive review of hoist electric drives and controls as applied to mine hoists is set forth with special reference to duty cycle calculations and their effect on electrical component selection.

Jan 1, 1988

By I. L. Nichols

The inplace cyanidation leaching of gold from placer deposits is a potential method for treating gravels too deeply buried and too low in gold content to be processed economically by conventional dredging methods. Laboratory experiments were made to evaluate those placer cyanidation factors adaptable to small-scale studies. The variables investigated included gold particle size and location in sand beds, cyanide solution flow rate, and cyanide solution strength as factors affecting gold solubility rates. The solution flow rate, in turn, was influenced by variables such as bed slope, solution head pressure, and sand size, and the effects of these factors were studied. Free gold, minus 150-mesh and finer in size, is rapidly dissolved by dilute cyanide solutions from mixtures of gold and silica sand prepared to simulate placer deposits. About 94 percent of minus 325-mesh free gold was extracted in 5 hours from silica sand mixtures, and 94 percent extraction of minus 150-mesh gold was obtained in 21 hours with 0.1 percent NaCN solutions. Moving solutions were almost twice as effective in leaching free gold from silica sand mixtures than stagnant solutions.

Jan 1, 1971

By S. L. Crouch

An important class of mining problems involves excavations in planar seam or vein-type deposits. In many instances it can be assumed that the seam is at 'infinite' depth in a homogeneous, isotropic or transversely isotropic, linearly elastic rock mss, and that the normal to the plane of the seam is a principal stress direction. Rational planning of excavations in such deposits requires a knowledge; of the stresses and displacements induced by complicated, irregular excavation geometries in the plane of the seam. This problem previously has been solved either numerically or by means of an electrical resistance network analog. Both of these methods effectively simulate the mined portions of the seam as a dislocation in an otherwise continuous mass, and determine the complete solution in terms of the stresses and displacements at the seam. In both cases, the plane of the seam is divided into a number - say, M x N - of squares, and the solution to the problem is determined in terms of the solution to an M x N system of equations. The numerical approach requires that these equations be solved explicitly, while the analog; solves them instantaneously with current analogous to stress and voltage to displacement. A purely numerical solution of practical problems can require a substantial amount of computer time, particularly in situations that demand some sort of sequential analysis, either due to successive mining or to nonlinear behavior of the seam material. This report describes a combined analog-digital computer system for solving problems that are impractical when either device is used separately. The digital computer and the analog are interfaced so that the digital computer can receive information from the analog via a switching matrix and an analog to digital converter, and can activate points of the analog via another switching matrix and a set of digital to analog converters. The resulting hybrid system can be used to simulate arbitrary "stress-strain" characteristics for any portion of the seam by an iterative procedure similar to the initial strain method used in nonlinear finite element analysis. Thus, the hybrid system combines the speed of analog computation with the decision-making capability of the digital computer: the analog instantaneously solves the set of equations, and the digital computer decides how the initial strains must be altered for the solution to be compatible with the prescribed "stress-strain" characteristics for the seam material. The hybrid computer system has many implications for rational planning of underground excavations, since it allows practically any type of inelastic seam behavior or artificial support characteristics to be simulated. Inelastic seam behavior, for example, might be due to either rock failure or to time-dependent deformation.

Jan 1, 1974

By F. W. Wood

The use of consumable.-electrode arc melting as a production technology is growing. One advantageous feature of this process is that it avoids ingot contamination by soluble crucible materials by employing a chilled metal crucible. Because the thermal balance under these conditions is rather delicate and does not necessarily provide a favorable environment for solidification, catastrophic imbalances can occur. The effectiveness and mechanistic roles of various factors are mostly unknown, and more intelligent insight regarding the distribution of temperature and heat is needed. Experience has provided several pertinent observations, some of which are quite superficial. The most meaningful data have resulted from studies of molten pool shapes and sizes and from measurements of heat flow through crucible walls. Overall experience, intuitively interpreted and supplemented, is sufficient nevertheless as a basis for a boundary-value treatment of the problem. A mathematical analysis based on a separation of variables, using conventional differential equation methods, provides a useful solution. For a cylindrical ingot, the temperature varies as a Bessel function of an argument proportional to the radius and as an exponential function of longitudinal position. Trial calculations using the problem solution seem to verify the general correctness of the result as compared with experience. The role and nature of solution parameters are also clarified, though not entirely resolved. It is revealed that the barrier to heat flow at the ingot-crucible surface has a prominent influence. Utility of the model embodied in the problem solution is readily demonstrated by considering a variety of contemporary questions about arc melting, and it is hoped that utility can be enhanced by improvement of the model.

Jan 1, 1968

By Frank E. Cash

The work of the United States Bureau of, Mines is concerned primarily with the prevention of accidents in the mining, petroleum, and allied industries. This report analyzes the fatal accidents in the coal mines of Tennessee and gives the pertinent factors in tabular and descriptive form, with interpretations and suggestions to operators, workers, and the State Division of Mines for the future prevention or reduction of accidents in coal mines. ACKNOWLEDGMENTS This study was made possible through the cooperation of A. W. Evans, chief mine inspector of Tennessee, and his secretary, Miss Hiliary Penny, who made available the department records and assisted in the segregation and assembly of the data.

Jan 1, 1935

By Paul E. Loustaunau

This report describes a project in which three structured underground coal mine equipment operator training programs were developed. The project was carried out in two parts. In the first part, a research study was conducted to determine how on-the-job training is currently conducted in industry, and to determine the overall effectiveness of current on-the-job training. In addition, the possible application of the principles of social learning theory to on-the-job training was investigated. In the second part three prototypes on-the-job training programs were developed for shuttle car operation, roof bolter operation, and continuous miner operation. These programs were carefully structured to eliminate the shortcomings of current industrial on-the-job training identified in the research study and incorporated the application of relevant principles of social learning theory. The programs are prototypes which underground coal mine training personnel can use as models to develop their own customized equipment operator training programs.

Jan 1, 1983

By R. D. Joseph

This report deals exclusively with roof-fall accidents that occurred during 1955 and 1956 in both anthracite and bituminous-coal mines throughout the United States. The report stems from a cooperative study conducted by the Bureau of Mines and the Roof-Control Committee of the Coal-Mining Section, National Safety Council. The study includes an analysis of individual accident reports, sets forth the measurable factors, and compares such factors with a representative sample of average data from 39 anthracite mines and 117 bituminous mines (appendixes A and B). Particular emphasis is placed on fatal roof-fall accidents with respect to their causes, locations, and the methods of support used at the point of occurrence. INTRODUCTION The purpose of the report is to classify all measurable details of the occurrences of roof-fall fatalities so that the material presented will assist those promoting safety and will serve as a manual for those whose principal duty is inspection of mines.

Jan 1, 1958

The principle activities of the Explosives Research Laboratory from July 1, 1961 to June 30, 1962, are described briefly in part 1. Part 2 gives short abstracts of publications that appeared during fiscal year 1962; in general, the research reported in these publications antedates the report period. Part 3 gives the results of an investigation which, although too limited to warrant separate publication, merits presentation in some detail because of current interest in ammonium nitrate-fuel oil compositions.

Jan 1, 1964

By Peter J. Clarke

The Soviet-controlled Government in Afghanistan continued to emphasize development of the country's mineral resources, primarily to supply raw materials and fuel to industrial areas in the Soviet Central Asian republics. In addition to expanding production of natural gas for export to the U.S.S.R., a $600 million2 Soviet-Afghan cooperation project, 1 of 167 such projects established since 1981, was devoted to exploiting the Ainak copper deposit, south of Kabul in Logar Province. Also being developed was the large Hajigak iron ore deposit in the Hindu Kush Mountains, 100 kilometers northwest of Kabul. In addition to these minerals, Afghanistan already produced small quantities of barite, cement, coal, gypsum, salt, and possibly some lapis lazuli. Afghanistan was the world's leading producer of lapis lazuli, a semiprecious gem stone, prior to the Soviet invasion in 1978, but production, although no longer reported, has probably been significantly reduced. It was also reported that Soviet mining engineers and technicians have commenced producing uranium from Lashkangah in the mountainous Khawaja Rawash area near Kabul.3 The Government was also considering mining chromite from Herserak and Mohammed Agha Kulanger, near the border with Pakistan.4 Afghanistan's overall economy remained stagnant in 1983, a result of continuing armed resistance to the Soviet-installed government. The gross domestic product (GDP) was estimated at about $2.8 billion, only marginally higher than the 1982 level. The value of exports was estimated at $720 million, up less than 2% over that of 1982, while imports rose approximately 8% over the same period. Natural gas was by far the leading export, earning about $295 million, up 4% over that of 1982. Approximately 90% of Afghanistan's natural gas production was exported to the U.S.S.R. Gas exports were used to pay the country's debt to the U.S.S.R., and also to pay for its supplies of petroleum products and other goods, which were imported almost exclusively from the Soviet Union. Some of Afghanistan's petroleum products were supplied by the U.S.S.R. as grants in aid, as Afghanistan did not have any domestic petroleum refining capacity.

Jan 1, 1985

By E. C. Perkins

As part of a program for developing methods of using domestic titanium deposits, the Bureau of Mines investigated methods for chlorinating titanium slags prepared from titaniferous minerals by electrosmelting. Titaniferous slags were made from ilmenites in the following deposits: Valley County, Idaho; Trail Ridge, Fla.; Aiken, S. C.; and Maclntyre, N. Y.; titaniferous magnetite from Iron Mountain, Wyo., were also evaluated. The tests were made in two chlorinators, a 4-inch and a 36-inch unit. Preliminary testing was done in a 40-millimeter bench-type unit. Chlorine gas was contacted with a loose mixture of titaniferous slag and carbon at a high temperature to form titanium tetrachloride. The moving-bed system used in this work involved a downward movement of feed countercurrent to the chlorine flow, and residues continuously removed from the bottom of the reactor. The performance characteristics of these slags depended on their composition, which varied widely according to the geographic source of the ore. The results showed that all but two of the slags could be chlorinated as effectively as rutile, converting 70 to 80 percent of the titanium to the tetra-, chloride. The two slags that proved difficult were made from New York ilmenite and Wyoming titaniferous magnetite. These slags contained enough magnesium to cause clinkering, which necessitated that the bed be prematurely withdrawn before more than 70 percent of it could react. The iron content of the slags did not interfere with operating the chlorinators. The data from the 4-inch and the 36-inch units were in agreement on the relative amenability of the slags to chlorination.

Jan 1, 1962

By J. W. Thompson

"The Republic of Colombia on December 30, 1919, enacted a new petroleum law. The Act is expressly limited to mineral oil, natural gas, bitumen, wax and fossilized resin and to asphalt intended for export.The law is not only intended to encourage local investors, but to attract foreign capitalists for oil development. Provision is made for a special edition ion of the law in such languages as the Government may deem necessary to give it extensive circulation within the country and abroad. The published editions must contain the provisions of the law relating to alienship and naturalization.All public lands, or what are termed unclaimed lands, are open to flee prospecting for the purpose of discovering the deposits named in the law, A prospector must obtain from the Government a, license which binds him to deliver to the Government topographic plans of the lands prospected, together with reports of their prospective yielding capacity. This license does not vest the li¬censee with any preferential right for contracting or leasing and may be drawn by the Government at any time.If a discovery is made by a licensee of any of the deposits named and he desires to exploit the same, he must present a memorial or application to the Ministry of Public Works, stating:- (a) the location and municipal district in which deposit beds are found; (b) boundaries of the zone of exploitation, which shall not be more than 5,000 or less than 1,000 hectares; (c) the names and nationality of all persons for whom the lease is sought and the action and time within which,they propose to make the exploitation; (d) the name of the corporation and its legal representatives with their residences; (e) if an alien, he must state his willingness to comply with the law relative to alienship and naturalization; (f) agreement to abide by all of the provieions of the law with regard to Government supervision, payment of taxes, rate of lease and causes of forfeiture; (g) the rate of rent or royalty that the applicant offers to pay, together with any other circumstances that may make the proposed lease advantageous to the Nation."

Apr 1, 1920

By G. Hakes

A data bank on bolter technology was assembled which included state-of-the-art industrial equipment as well as new equipment currently under development for the U.S. Bureau of Mines. This information was augmented by field visits to selected USBM contractors, mine operators and others for the purpose of obtaining a thorough understanding of present coal mine roof bolting safety and productivity problems. These direct contacts provided valuable insight regarding requirements for new bolting equipment necessary to assure wide user acceptance. Using this background material and information, a series of roof bolter concepts was developed offering improved operator safety with minimum impact on productivity. The concepts developed utilize existing componentry and technology wherever possible. All of the concepts feature a fully protected operator station located 6' to 10' outby the active bolt line and the hazardous rotating machinery.

Jan 1, 1978

By Donald O. Capstick

The U.S. Bureau of Mines conducted an inventory of the prospects and mineral resources in the Scodies RARE II area (No. 5212) in 1982. No mineral production is recorded from the area, and no mines are being developed. The Scodies RARE II area is comprised primarily of light colored granodiorite with minor inclusions of mafic granitic rocks. Late stage differentiates of magmas resulted in quartz veins and pods. Metasedimentary rocks which have been mineralized in some parts of the Sierra Nevada were not observed within the study area during this investigation but small inclusions have been reported.

Jan 1, 1983

By Sara Jane Boles

In recent years the interest in rare-earth compounds as refractory materials has exceeded the available literature on the subject. While some basic properties, such as density and melting point, of the more readily available rare-earth compounds have been reported in the literature, relatively few papers can be found that deal comprehensively and primarily with high-temperature refractory properties and applications of rare-earth oxides, carbides, sulfides, and nitrides. Therefore, this bibliography has been pre-pared for the use of the ceramic industry as a guide for locating and utilizing the scattered and frequently fragmentary information available. The term "rare earths", as applied in the literature search for this bibliography, is understood to include the following elements: cerium, dysprosium, erbium, europium, gadolinium, holmium, lanthanum, lutetium, neodymium, praseodymium, samarium, terbium, thorium, thulium, uranium, and ytterbium. (On the periodic chart, these elements appear as numbers 57 through 60, 62 through 71, 90, and 92.) It is emphasized that many of the abstracts included are from papers in which the rare-earth compound or compounds are treated along with several other ceramic materials, are mentioned only secondarily, with primary interest placed on a more commonly used refractory material, or are used as part of a mixture of materials formed experimentally and reported on in the paper. As the better known rare-earth materials, such as the oxides of uranium, thorium, and cerium, appear more frequently in the literature, they also appear more frequently in this collection. Articles abstracted include only information on the basic properties that are of interest to the refractories investigator. References to crystal lattices and related topics are generally excluded from this publication. The temperature 1,500° C. has been set arbitrarily as the lower limit for reported data on thermal properties. However, because of the scarcity of information, some reports are included in which data are limited to those obtained at lower temperatures. Many of the articles abstracted include lists of references that will be of additional assistance in pursuing specific lines of investigation.

Jan 1, 1962

By Rudolf E. Greuer

The existing computer programs for the simulation of ventilation systems under normal ventilation conditions are reviewed and a suitable program for including the influence of mine fires is selected. New program parts are written for the consideration of methane productions in coal mines, heat and gas productions of mine fires, temperature and air composition changes in ventilation systems, and the ventilation forces resulting from the latter. Other program parts are provided for the detection of danger zones and reversed air currents and for the inclusion of recirculated air currents in the network analysis. Existing program and new program parts are combined. The resulting new program can be used for a multitude of assignments. It is designed for the practical ventilation engineer and should be applicable to all types of ventilation emergency plans, in particular mine fire plans. The organization of the program and its mathematical basis are described. A FORTRAN IV listing and several flow diagrams are included. Eight executed examples are discussed, input and output for these examples explained. Storage requirements and execution times are estimated.

Jan 1, 2011

By Russell Griffin

The current state of the art of fire and smoke detection technology is reviewed from the standpoint of suitability for use in under- ground metal and nonmetal mines. Detection modes, fire signatures, and environmental considerations are included. Preliminary results of long- term, in-mine tests are presented.

By McHenry Mosier

The Bureau of Mines, United States Department of the Interior, has established a testing adit on the Government reservation at Mount Weather, Virginia, to facility to research on the fundamental tats of mining under actual metal-mining conditions. A number of sites in several Eastern States were investigated, out Mount Weather was selected because the rock seemed best suited for rock drilling and other mining tests and because the ground was already owned by the Federal Government, the site having been acquired in 1902 for use of the Weather Bureau. The testing edit has an advantage over en active metal mine for certain investigations because variable conditions affecting any particular research problem can be controlled and maintained in a fixed status, whereas in an operating mine this seldom is feasible. Operations were begin September 1935, with a crew of four laborers under a resident engineer. The laborers were recruited from, nearby farms, and. although they had no previous mining experience, they have developed into satisfactory miners.

Jan 1, 1939

By J. B. Stott

The performance of an adiabatic calorimeter for measuring heats of oxidation of coal is assessed and suggestions made for its improvement and calibration. The use of magnetic analysers for measuring small oxygen deficiencies in air is described and three different methods of measuring the output for such a meter are characterised. The occurrence of spontaneous heating in an 800 tonne heap of Wyoming coal is briefly described. The major part of the report deals with the oxidation of Pittsburgh seam and Wyoming subbituminous coal and describes an experiment in which 1 tonne of Wyoming coal is stored in a 5 metre long insulated container whilst air was passed through. Temperature rises, rates of oxygen absorption and gas compositions of the air stream were measured. The report relates the results of these-experiments to a theory of spontaneous heating developed by Stott and Quan which stresses the importance of the moisture content of the coal and the relationship between the heat necessary to evaporate this water to the heat available from coal oxidation. The work was carried out over a five month period and the emphasis is on demonstrating the effects of moisture transfer and confirming the theory of Stott and Quan.

Jan 1, 1980

By J. M. West

Expanded war in Viet-Nam overshadowed activities in the Far East in 1965, diverting capital and materials from potential regional development projects. Japan with-stood a period of business recession that was particularly felt by its coal mining and iron and steel industries. Toward yearend signs of improvement began to show. Despite the recession with attendant credit restrictions and forced cutbacks in areas of overproduction, Japan's overall industrial output rose nearly 5 percent during the year. Foreign trade, liberalized in 1964, was a strong point in the Japanese economy and took the place of lagging domestic demand. Japan maintained its third place in world production of iron and steel ahead of West Germany and in 1965 was the world's fore-most exporter of iron and steel in primary and semimanufactured forms. Economic setbacks in mainland China caused by its "Great Leap" failures and subsequent withdrawal of Soviet technical assistance were difficulties relegated to the past. However, a newly formed "Red Guard" political group, part of a so-called cultural revolution, was due to cause new disruptions in 1966. Nevertheless, significant gains were claimed in Chinese industry, and the country approached self-sufficiency in petroleum in 1965 by virtue of its Tach'ing oilfield. Restoration of friendly relations was achieved between South Korea and Japan accompanied by Japanese offers of industrial aid and increased trade. Indonesia's economy was deteriorating; the country withdrew from regional development organizations and continued its stubborn confrontation policy against Malaysia throughout 1965. Late in the year after a Communist uprising had been quelled, there was a period of political retrenchme t and it was hoped that economic improvements would follow. Petroleum remained a strong area in Indonesia's varied resources, and its production was increasing. Tin output declined, however, because of operating difficulties.

Jan 1, 1967

By Robert Stefanko

A series of workshops were conducted -with invited participants from the coal mining industry to identify the most pressing research and development needs of the industry. Six workshops were held on the following subjects; Research Priorities for Mining-Oriented Universities, R&D Needs-for Surface Coal Mining, R&D Needs for Deep Coal Mining, R&D Needs for Anthracite Coal Mining, R&D Needs for Coal Mine Health and Safety, and R&D Needs far Environmental Control in Coal Mining.

Jan 1, 1975